SFC-FID ASTM System SFC-4000 Series SFC Performance Innovation Reliability
The JASCO SFC-FID system has been developed as a simple and validated turn-key solution for the measurement of the two ASTM standard measurements that require SFC. ASTM-5186 for aromatics analysis, in diesel and aviation fuel and D-6550 for olefin content in gasoline. The SFC-FID system can also be configured for any analysis that may require SFC for the separation of volatile materials such as oils, fuels and lubricants. Table of contents System ASTM Requirements 4 System Features 5 Performance 6 Software ChromNAV 7 2 3
ASTM D5186 and D6550 Requirements System Features The two ASTM standard test methods, D5186 and D6550 have specific requirements that must be met for system compliance. ASTM D5186-15 Standard Test Method for Determination of the Aromatic Content and Polynuclear Aromatic Content of Diesel Fuels and Aviation Turbine Fuels By Supercritical Fluid Chromatography ASTM D6550-15 Standard Test Method for Determination of Olefin Content of Gasolines by Supercritical-Fluid Chromatography Module Requirement Column Oven and Valve Switching The compact column oven houses the silica and silver columns and also contains built-in column switching valves required for the ASTM D6550 standard test method. This integrated design ensures extremely stable temperature for the columns and valves to provide the highest resolution and reproducibility. Back Pressure Regulator The patented design of the back pressure regulator provides unmatched baseline stability and retention time reproducibility, which is critical to the reliability required for the ASTM methods. Detection A GC oven contains a pre-bpr splitter to control the sampling ratio to the FID detector. Supply of the combustion gases is controlled automatically with a fl ame-out sensor for safe operation. Pump Autosampler Column Oven 0.3% RSD retention time or better sub-micron injection capabilities 0.2% repeatability, mass % or better for 1% aromatics (ASTM D5186) 0.1% repeatability, mass % or better for 1% olefi n (ASTM D6550) 0.5 C temperature control precision or less Switching Valves 2 allowing for 4 different valve positions (ASTM D6550) Columns Silica and Silver loaded Silica (ASTM D6550) Resolution D5186 Aromatics and Non-Aromatics of at least 4 Monoaromatics and Polynuclear aromatics of at least 2 Resolution D6550 Aromatics and Olefi ns of at least 3 The SFC-FID ASTM system meets and exceeds all of the above requirements for both ASTM D5186 and D6550 providing a system that covers both analyses. ASTM 5186 Pump The CO 2 pump includes built-in peltier cooling and has an asymmetric dual piston design to maintain a highly stable CO 2 fl ow that yields retention time reproducibility of 0.05%, far below the ASTM requirement of 0.3%. Autosampler The autosampler includes fi xed injection volumes of 0.5, 0.2 or 0.1μL to meet the requirements of the ASTM methods. The high precision yields a mass repeatability of 0.04%, well below the 0.1% requirement 1% olefi n for ASTM D6550. The autosampler injection procedure includes a sample preload feature that eliminates the wait time between injections, saving time and mobile phase. Columns Extensive research went into the development of the silica and silver loaded silica to produce a silica column with exceptional resolution and silver column for differential retention of olefi ns, while still maintaining a short analysis time. ASTM 5186 ASTM 6550 4 5
System Performance ChromNAV Software The system calibration uses traceable standards and achieves excellent linearity with high correlation coefficient for accuracy and precision in the determination of unknown samples. The ASTM standards used for system performance testing for D5186 and D6550 were acquired from Spectrum Quality Standards. Instrument Control The ChromNAV chromatography data system includes integrated instrument control through an Ethernet based interface, with validation and data analysis. For the ASTM methods the preconfigured system can be fine-tuned to individual column requirements. Injection and valve timing are controlled automatically with excellent timing precision for repeatable run to run reproducibility. The chromatograms from the FID detector are used to monitor the separation, create calibration curves and calculate values for samples. An option UV or PDA detector can also be included in the system if required. The ASTM methods state specific acceptance criteria for repeatability and reproducibility, which are exceeded as seen in the data below. ASTM Repeatability % Acceptance Measured 1.0 ±0.110 0.04 ASTM Reproducibility % Acceptance Measured 1.0 ±0.470 0.10 Data Acquisition Pre-built methods and sequences are utilized for quick and easy sample analysis. Within the same sequence, samples for each ASTM standard test method can be included. The sequence allows inclusion of predetermined integration, peak identification, calibration and fully customizable reports for complete automation from sample analysis to report printing. ChromNAV allows the export of raw data and peak calculation results to Microsoft Excel automatically. 3.5 ±0.281 0.06 6.0 ±0.422 0.06 8.5 ±0.548 0.20 12.0 ±0.709 0.55 17.0 ±0.921 0.90 25.0 ±1.230 0.58 3.5 ±1.203 0.16 6.0 ±1.802 0.34 8.5 ±2.340 0.38 12.0 ±3.030 0.44 17.0 ±3.935 1.05 25.0 ±5.255 1.63 6 7
JASCO INTERNATIONAL CO., LTD. 11-10, Myojin-cho 1-chome, Hachioji, Tokyo 192-0046, Japan Tel: +81-42-649-3247, Fax: +81-42-649-3518, Web: www.jascoint.co.jp/english/ Australia, China, Hong Kong, India, Indonesia, Iran, Japan, Korea, Malaysia, New Zealand, Pakistan, Philippines, Russia, Singapore, Taiwan, Thailand JASCO, INCORPORATED 28600 Mary s Court, Easton, Maryland 21601, U.S.A. Tel: +1-410-822-1220, Fax: +1-410-822-7526, Web: www.jascoinc.com Argentina, Bolivia, Brazil, Canada, Chile, Colombia, Costa Rica, Guatemala, Mexico, Paraguay, Peru, Puerto Rico, United States of America, Uruguay, Venezuela JASCO EUROPE S.R.L. Via Luigi Cadorna 1, 23894 Cremella (LC), Italy Tel: +39-039-9215811, Fax: +39-039-9215835, Web: www.jascoeurope.com JASCO Deutschland www.jasco.de JASCO UK www.jasco.co.uk JASCO France www.jascofrance.fr JASCO Benelux www.jasco.nl JASCO Spain www.jasco-spain.com Algeria, Austria, Belgium, Cyprus, Denmark, Egypt, Finland, France, Germany, Greece, Hungary, Israel, Italy, Jordan, Kuwait, Lebanon, Luxembourg, Morocco, Netherlands, Norway, Poland, Portugal, Romania, Saudi Arabia, South Africa, Spain, Sweden, Switzerland, Syria, Tunisia, Turkey, United Arab Emirates, United Kingdom, Yemen ISO 9001 Certified ISO 14001 Certified Products described herein are designed and manufactured by ISO-9001- and ISO-14001-certified JASCO Corporation