Wall-Mounted Eyewash Table of Contents Pre- Information.............. 2 Instructions.................. 3 Assembly of Components............... 4 Parts List............................ 5 Bradley S19 220bf Eye Face Wash With Spray Ring
R 114-051 Datum Signe P.O. BOX 309, MENOMONEE FALLS, WI 53052-0309 USA TEL: 1-800-BRADLEY FAX: (262-251-5817) http://www.bradleycorp.com P.O. Box 309, Menomonee Falls, WI 53051 TEST THIS UNIT EACH WEEK DIESES GERÄT 1ST WÖCHENTLICH ZU PRÜFEN. ESSAI HEBDOMADAIRE Test-operate valve(s) each week and sign below. Report any malfunctions immediately. Ventil(e) wöchentlich im Testbetrieb prüfen, bestätigt durch Unterschrift. Jegliche Störung sofort melden. THIS SIDE UP Test le fonctionnement des valves chaque semaine et signe en bas. S'il y à quelque chose qui ne va pas fait un rapport immédiatement. Unterschrift Packing List WARNING Read this installation manual completely to ensure proper installation, then file it with the owner or maintenance department. Compliance and conformity to drain requirements and other local codes and ordinances is the responsibility of the installer. Separate parts from packaging and make sure all parts are accounted for before discarding any packaging material. If any parts are missing, do not begin installation until you obtain the missing parts. Flush the water supply lines before beginning installation and after installation is complete. Test the unit for leaks and adequate water flow. Main water supply to the eyewash should be ON at all times. Provisions shall be made to prevent unauthorized shutoff. The ANSI Z358.1 standard requires an uninterruptible supply of flushing fluid at a minimum 30 PSI (0.21 MPa) flowing pressure. Flushing fluid should be tepid per ANSI Z358.1. The inspection and testing results of this equipment should be recorded weekly to verify proper operation. This equipment should be inspected annually to ensure compliance with ANSI Z358.1. Workers who may come in contact with potentially hazardous materials should be trained regarding the placement and proper operation of emergency equipment per ANSI Z358.1. 2
Supplies Required: (4) 5/16" wall anchors and bolts Pipe sealant Piping to 1/2" NPT water supply inlet Piping to 1-1/4" drain outlet Sign-mounting hardware NOTE: Local codes may require the installation of a backfl ow prevention valve to complete proper installation. Compliance with local codes is the responsibility of the installer. Valve must be tested annually to verify that it is functioning properly. Backfl ow prevention valves are not included with the fi xture and may be supplied by the contractor or purchased from Bradley Corporation. Step 1: Install inlet drain fitting 1. Rough-in supply piping and drain piping at the dimensions shown. Mark the bracket and mounting hole locations on the wall. Install suitable wall anchors (sup plied by installer) at the bracket and mounting hole locations. 2. Secure support brack ets to the wall with 5/16 bolts (supplied by installer). 3. Position the eyewash with skirt over the support brackets and rest the back of the skirt on the brack ets. 1-7/8" (48mm) 35" (887mm) Suggested Height to Floor 6-7/8" (175mm) 4-19/32" (117mm) 9/16" (14mm) 2-3/4" (70mm) 5-1/2" (140mm) 15" (381mm) 9-3/16" (233mm) 10-5/16" (262mm) 3-5/8" (92mm) Support Brackets 4-1/2" (114mm) 1/2" NPT Supply Mounting Holes 1-1/4" Drain Outlet 36-3/4" (933mm) Suggested Height to Floor 4. Fasten the skirt to the wall with 5/16 bolts (supplied by installer) at the mounting hole locations. Step 2: Assemble components 1. Assemble eyewash components as shown on page 4. 3-3/4" (95mm) 19" (483mm) 15-1/4" (368mm) Apply pipe sealant (supplied by installer) to all male-threaded pipe joints. Use a strap wrench around pipes when tightening to prevent marring. 7-1/2" (191mm) Support Brackets Mounted on Wall 5-1/4" (133mm) Step 3: Connect water supply 1. Connect the water supply piping (supplied by installer) to the 1/2" NPT inlet on the eyewash. 24" (610mm) 2. Connect the tailpiece to the 1-1/4" drain outlet on the eyewash. 3. Mount the safety sign to the wall using sign-mounting hardware (supplied by installer). 4. Open the water supply lines. Test for leaks and adequate water flow. 3
114-051 P.O. BOX 309, MENOMONEE FALLS, WI 53052-0309 USA TEL: 1-800-BRADLEY FAX: (262-251-5817) http://www.bradleycorp.com R P.O. Box 309, Menomonee Falls, WI 53051 TEST THIS UNIT EACH WEEK DIESES GERÄT 1ST WÖCHENTLICH ZU PRÜFEN. ESSAI HEBDOMADAIRE Test-operate valve(s) each week and sign below. Report any malfunctions immediately. Ventil(e) wöchentlich im Testbetrieb prüfen, bestätigt durch Unterschrift. Jegliche Störung sofort melden. Test le fonctionnement des valves chaque semaine et signe en bas. S'il y à quelque chose qui ne va pas fait un rapport immédiatement. Datum Unterschrift Signe Assembly of Components 1.12 1.11 1.10 12 1.9 1.8 1.6 1.5 1.7 1 13 1.4 1.3 11 4 1-1/4" Drain Outlet 2 1/2" NPT Supply Inlet 3 1.2 1.1 5 6 7 8 14 9 10 7.1 NOTE: Items 1.1-1.12 come preassembled as Item 1. 4
Parts List Item Part No. Qty Description Item Part No. Qty Description 1 S90-290 1 Spray Ring Assy. 1.1 111-084A 1 Inlet-Drain Fitting w/elbow 1.2 124-028 1 Center Seal Gasket 1.3 187-053 1 Eyewash Bowl 1.4 173-009 1 Cup Strainer 1.5 S21-073 1 Supply Pipe 1.6 113-1159 1 Spacer, Drain 1.7 S05-100 1 Eyewash Yoke 1.8 107-371 2 Dust Cover 1.9 269-651 1 Swivel Stem 1.10 124-055 2 Quad Ring 1.11 139-087 1 Spray Ring 1.12 110-199 1 Acorn Nut 3 169-1024 1 Coupling 4 111-087 1 P-trap/Wall Tube 5 113-751 1 Pipe, 1/2" x 2-1/2" 6 269-1100 1 Street Elbow 7 S27-282 2 1/2" Ball Valve with Nut 7.1 110-215 1 Nut only 8 153-372R 1 Ball Valve Adapter (RH) 9 S08-336 1 Handle Assy. 10 142-002DA 1 Lockwasher 11 140-143 2 Support Bracket 12 114-051 1 Safety Sign 13 204-421 1 Emergency Inspection Tag 14 S30-070 1 Ball Valve Kit 2 S87-027 1 Cabinet Assy. Prepack S30-071 includes Items 7.1, 8, 9, 10 Prepack S05-127 includes Items 1.9, 1.10, 1.11, 1.12 5