MODEL NO.:Hovo 710 PUSH
Product Features Product Parts Product Illustration Product Operations and User Interface Icons Battery Installation and Storage Charging Dock Station and Battery Charging Methods Product Operations By Remote Control Unit Schedule Cleaning Time Virtual Blocker Operations
Before using this product, please read the following safety instructions and follow all normal safety precautions. Read this user manual thoroughly and carefully before using this product. Save this user manual. Follow these precautions to reduce the risk of injury or damage. Only a certified technician can disassemble and/or repair the product. non-authorized Do not use product near any flammables. Do not clean while product is charging. Do not over bend or put large weight on the power cord. This product is for indoor use and clean dry surface floor only. Before using, remove damageable objects (glass, textiles, papers, etc.) that can get caught in the cleaner's brush or vacuum intake. Before charging battery, make sure to (1) connect AC adapter to cleaner or charging base first; (2) then plug the adapter to the wall outlet next sequence to avoid sparks. To avoid injury; inform all people in the house that the unit is doing cleaning. Use this product in temperatures between 0 C and 40 C (32 F and 104 F). Remove battery from unit before recycling or scraping the unit. Disconnect AC adapter before removing the battery. The battery should be properly disposed. NOTE: Do not allow children to operate this product unless they are supervised by an adult
P r o d u c t F e a t u r e s 1. Voice message guidance and touch screen operations 2. Self-adjustable carriage of suction assembly and/or sweeping assembly so they will be closer to the ground to do better cleaning. 3. Patented ONE FIT ALL brush system with both soft bristle and rubber base to do good cleaning both on hard surface floor and carpet floor. The entangled hairs on brush blades can be easily cleaned and brush blades are replaceable. 4. Two-way 6 long wide high wattage UV lamp which kills up to 99% of bacteria both on floor and in dustbin. 5. Pre-filter and High-Efficiency Particle Absorption (HEPA) filter removes over 99% of airborne particles including mold, dust, and dust mites. 6. Two-way virtual blocker can create one or two invisible barriers that cleaner will not cross. 7. Reduce motor noise level manually (MUTE) or via lighting sensor. 8. Interchangeable sweeping assembly (for carpet cleaning) and suction only assembly (for hard surface floor cleaning).
P r o d u c t F e a t u r e s 9. Dustbin full condition alarm warning 10. Dark area cleaning mode Cleaner will clean under bed or sofa area for about 5 minutes. 11. Garbage/Dirt detection Cleaner will increase suction power to clean the area.
MODEL NO.:Hovo 710 PUSH P r o d u c t P a r t s Main Unit and Accessories PUSH cleaner * 1 set Charging dock station * 1pcs Remote controller * 1pcs Power adapter * 1pcs Trailing bar * 1pcs Mop * 2pcs Suction inlet * 1pcs Side brush * 2pcs extra HEPA filter * 1pcs extra 05
PUSH P r o d u c t I l l u s t r a t i o n bin out Manual charging port Front wheel
P r o d u c t O p e r a t i o n s a n d U s e r I n t e r f a c e I c o n s UV 1 2 3 4 5 6 7 SPOT AUTO DOCK Product Operations and User Interface Icons Note: Remove the small items or obstacles in the house before cleaning, especially the power cord and other objects that may be get tangled easily; if the battery is low during cleaning, the cleaner stops cleaning and beeps five times, then search for charging station and recharge battery. AUTO AUTO Automatic cleaning button: Press this button to start automatic cleaning; if the battery is low during cleaning, it will look for charging dock station automatically; During the cleaning process, touch any button on the panel to stop cleaning. SPOT SPOT Spot cleaning button Press this button, the cleaner automatically enters a range about 1m and cleans this area in spiral mode; it will clean the area for about 2-3 minutes and stop. During the cleaning process, touch any button on the panel to stop cleaning. DOCK DOCK Charging button Press this button, and the cleaner will search for charging station to recharge battery automatically. SCHEDULE Press the SCHEDULE button on the remote control, the icon turns on, and the cleaner enters current week, hour/minute and time week, hour/minute settings (see Remote control schedule setting on page 11). UV UV UV When the icon is on, the UV lamp of the machine tarts working; when the icon is off, the UV lamp is turned off. is on and s Note: When the cleaner is powered on in the first time, the system turns on UV lamp by default. 07
P r o d u c t O p e r a t i o n s a n d U s e r I n t e r f a c e I c o n s 1 2 3 4 5 6 7 2 Week day displays: 1 for Monday, 2 for Tuesday, 3 for Wednesday, 4 for Thursday, 5 for Friday, 6 for Saturday, 7 for Sunday ging the cleaner battery, turn the power switch ON first! Otherwise cleaner battery cannot be recharged and it will show E010 error code. you empty and clean dustbin and brushes after each use. er movement path is set by default and changes to spiral spot cleaning mode automatically if very dirty area is detected. automatically. Battery Installation and Storage s for about five minutes,then it will go back to AUTO mode Enter dark cleaning mode, you can either put the cleaner in the dark area or push DARK button on remote control unit. be used for an extended period of time, we recommend that you remove the battery. For long-term storage, fully charge the battery first, then remove it, and store it in a cool, dry place.
Charging Dock Station and Battery Charging Methods A. Auto charging via charging dock station and against the wall. 2 meters in front 0.5 meters on both sides. charging. dock station for automatic battery charging. wrap the DC power cord on the back of charging dock station, and do not put the power cord on the ground. Otherwise, it will affect the searching of charging dock station 5. Press DOCK on control panel or remote control, then cleaner will return to charging station and recharge battery. B. Manual charging battery Plug AC adapter power cord to the manual charging socket on unit first, then plug AC adapter to wall outlet next. Make sure to turn on cleaner power switch to recharge battery.it takes about 3 hours to fully charge a low power battery.
PUSH P r o d u c t O p e r a t i o n s B y R e m o t e C o n t r o l U n i t Remote control buttons Fig. 1 Press and the cleaner will search charging dock station and recharge battery. Press OK key to stop. Press to turn on/off the UV lamp on the bottom of the cleaner. Press and the cleaner will enter energy saving mute cleaning mode. (reduce motors noise level). Press and the cleaner will enter spiral/spot cleaning mode. Press OK key to stop. Press and the cleaner will enter sleep or working mode (in sleep mode, press and hold this button for 10 seconds to enter the working mode). Press and the cleaner will enter time/schedule clean ingsetting. Press and the cleaner will enter dark cleaning mode. Press to confirm (in standby mode, press this button to enter wall-following cleaning mode). Press and the cleaner will enter automatic cleaning mode. Press OK key to stop. Press and the cleaner will move forward. Press and the cleaner will move backward. Press and the cleaner will move to the left. Press and the cleaner will move to the right. AAA AAA 4m Fig. 2 Fig. 3 Note: 1. Before using the remote controller, install two AAA batteries first. (Fig. 2) 2. To control the cleaner with the remote controller, aim the remote controller at the sensor of the cleaner within 4 meters or 13 feet (Fig. 3). 3. When battery power is low, the remote control s effective distance will be shorter. If your vacuum does not respond well to the remote, please replace remote batteries ASAP. 10
S c h e d u l e C l e a n i n g T i m e Day of The Week and Time Setting Day of The Week Setting: day of the week setting; to select day of the week and it will be steady; to cancel day of the week selection and it flashes; day of the week and enter current Hour/Minute setting; Hour and Minutes Setting: day of the week, press Cleaning Time Setting Day of the Week: Day of week selection and it flashes; steady; press the button to cancel You can read current setting value by press OK after enter schedule Day of the week setting or cleaning time setting.
V i r t u a l B l o c k e r O p e r a t i o n s Introduction of virtual blocker Side indicator Front indicator AA AA 1.Front 0. Power switch 2.Side 3.Front, side 0 1 2 3 Side IR window Front IR window 0123 Side switch Fig.1 Fig.2 Fig.3 Turn button Can : turn off power of virtual blocker, switch among front, side, front/side. Turn to 0 position, the power supply of the virtual blocker will be cut off. Turn to position 1, the power supply of the virtual blocker is turned on; the machine is in front working mode, and the control range of the virtual blocker is within 2meters; Turn to position 2, the power supply of the virtual blocker is turned on; the blocker is in side working mode, and the control range of the virtual blocker is within 2meters; Turn to position 3, the power supply of the virtual blocker is turned on; the blocker is in dual working mode (front + side), and the control range of the virtual blocker is within 2meters; How to Operate Virtual Blocker 1. Before using it, open battery compartment cover on the bottom of virtual blocker, and insert two AA batteries properly according to the instructions (Fig. 3). Note: Incorrect battery polarity installation may result in operation failure or damage of the virtual blocker, and may cause other unexpected occurrence. 2. The battery life time depends on working modes and frequent of usage. In order to save battery power, please select appropriate virtual blocker working mode to reduce the transmission power; when the virtual blocker is not in use, turn the power off. 3. The virtual blocker is often placed near stairs, by the door, or at any places that requires a virtual blocker. 4. During use, ensure that the virtual blocker and the vacuum cleaner are placed on the same level, and there is no obstruction between the virtual blocker and the cleaner (Fig. 4). 5. In actual use, the effective distance of virtual blocker depends on the environment, movement of the cleaner and remaining battery power. 6. The virtual blocker should be at least 50cm from the cleaner, otherwise it will cause interference. 7. Do not aim the IR emission window/hole at people s eyes! 2m Fig. 4 2m 12
bin cover.(fig.1) and pre-filter bin cover,and pour out the dirt and other rubbish (Fig.3,4 & 5). Pre-filter
T T
Drive shaft Fig. 1 Fig. 2 rubber cap Fig. 3 Fig. 4
action on solution column below to eliminate hairs or debris entangled on wheels Hairs or debris wrapped on left and right side brushes Empty dustbin,clean dirt on sensor tip and suction inlet Clear the hairs or debris on the left and right wheels Clear hairs or dirt on the left and right side brushes hairs wrapped on roller brush Clear hairs or debris on the roller brush bumper sensors failure bumper sensors are blocked customer service of your local distributor. solution Hovo 710 Unit dimension 13.5 diameter 3.5 height Dustbin capacity 700ml
Dimension Hovo 710 05X105 mm Dimension Hovo 710. 2 AAA batteries (not included) Dimension Hovo 710. 2 AA batteries (not included) AC adapter Dimension Output Hovo 710 40X70X95 mm 100-240V 50/60Hz 0.8A 24VDC 1.0A
Metapo Inc. http://www.infinuvo.com http://www.metapo.com For technical support and manufacturer warranty: http://support.metapo.com Warranty services coverage only valid if you buy products from our authorized resellers.