62MB,MC,MD,ME040-950 Energy Recovery Ventilators Installation, Start-Up and Service Instructions CONTENTS Page SFETY CONSIDERTIONS...1 INTRODUCTION...1 INSTLLTION... 1-58 Step 1 Inspection...1 Step 2 Install Roof Curb...1 STND-LONE PPLICTIONS COUPLED PPLICTIONS Step 3 Rigging and Handling...45 MOUNTING THE UNIT INDOORS Step 4 Installing ERV Transitions...47 ERV UNIT COUPLED WITH 3 TO 12 1 / 2 TON HVC UNIT Step 5 Make Electrical Connections...47 POWER SUPPLY ELECTRICL CONNECTIONS STRT-UP... 59-75 Preparation...59 Internal Wiring...59 Rain Hoods...59 Energy Recovery Wheel...59 DRIVE BELT IRSELS Blower Rotation...59 irflow Settings and djustments...59 FCTORY SETTING CURVE SELECTION DJUST THE ERV BLOWER SPEED MESURE MOTOR VOLTGE, MPERGE ND FN RPM BELT MINTENNCE Variable ir Volume Option...74 Operating Sequence...74 OCCUPIED MODE UNOCCUPIED MODE SERVICE... 75-78 Removing Wheel Segments for Cleaning (62M170-950 s)...75 Removing and Installing Non-Segmented Wheel for Cleaning (62M040 s)...75 Removing and Installing Non-Segmented Wheel for Cleaning (62M075,120 s)...76 Installing Wheel Segments (62M170-950 s)...76 Wheel Drive Motor and Pulley Replacement...77 Belt Replacement...77 MINTENNCE...78,79 STRT UP CHECKLIST...CL-1 SFETY CONSIDERTIONS Installation and servicing of air-conditioning equipment can be hazardous due to system pressure and electrical components. Only trained and qualified service personnel should install, repair, or service air-conditioning equipment. Untrained personnel can perform the basic maintenance functions of cleaning coils and filters and replacing filters. ll other operations should be performed by trained service personnel. When working on air-conditioning equipment, observe precautions in the literature, tags and labels attached to the unit, and other safety precautions that may apply. Follow all safety codes. Wear safety glasses and work gloves. These instructions describe how to install, start up, and service 62M energy recovery ventilator units. Electrical shock can cause personal injury and death. Shut off all power to this equipment during installation. There may be more than one disconnect switch. Tag all disconnect locations to alert others not to restore power until work is completed. INTRODUCTION The 62M energy recovery ventilator (ERV) units recover energy from building exhaust air and pre-condition ventilation air. ll ERV units are available in either vertical discharge (through the bottom) or horizontal discharge configuration. The 62MB and MC vertical discharge units are used when a stand-alone ERV unit is required. The 62MD and ME horizontal discharge unit can be used as a stand-alone unit, or can also be coupled with a Carrier rooftop unit. INSTLLTION Step 1 Inspection Inspect the unit; file a claim with the shipping company if the unit is damaged. Check the packing list to ensure that the correct items have been received and notify your Carrier representative of any discrepancy. Step 2 Install Roof Curb STND-LONE PPLICTIONS The ERV unit can be installed without being coupled with a Carrier rooftop unit. The ERV units can be installed in one of three stand-alone applications: down discharge, horizontal discharge, or a combination of both down discharge and horizontal discharge. When installing a stand-alone ERV unit refer to Fig. 1-45 and, complete the following: Locate the Roof Curb Prior to locating the roof curb consider the structural support required for the rooftop system and, the duct drop location in relation to the joists. llow sufficient space for service, clearance, and locations of vents or other sources of air. Manufacturer reserves the right to discontinue, or change at any time, specifications or designs without notice and without incurring obligations. Book 1 4 Catalog No. 536-220 Printed in U.S.. Form 62M-1SI Pg 1 1-06 Replaces: New Tab 10a 12a
Cover roof opening if installation of the ERV unit will not be immediate. Failure to cover roof opening could result in water damage and/or serious personal injury. ssemble the Roof Curb Connect the curb side and the curb end. See Fig. 1. Insert the tabs on the curb end into the slots on the curb sides. Press firmly until the pieces lock into place. It may be necessary to exert additional force to the top of the curb to lock the pieces in place. Ensure the curb pieces are locked together prior to proceeding. Repeat for all corners of the roof curb. Prepare Roof Curb Location Cut a hole in the roof for duct openings. See Fig. 2-5 for duct opening dimensions. Frame the opening to provide adequate structural support. Install Deck Pans and Duct Supports The roof curb may have a duct support and deck pans, depending on the model and application. Determine which end of the roof curb will be the duct end. Install the deck pans on the roof curb with the insulation side facing up toward the ERV base. Install the duct support between the supply and return openings. Set the Roof Curb Fit the roof curb assembly by measuring across the corners of the curb to ensure a square fit. Set the roof curb over the roof opening. Level the curb by placing shims under the bottom flange of the curb. Secure the curb in place by welding or fastening the curb to the roof. Cover the roof curb if installation of the ERV unit will not be immediate. Failure to cover the roof curb could result in water damage and/or serious personal injury. Install Ductwork Ductwork will be installed in the roof curb for vertical discharge and stand-alone applications. The duct will hang from the top of the curb. See Fig. 45 for standalone application airflow. NOTE: Ductwork must be installed before the ERV unit is set in place. Refer to Fig. 2-5 to determine the duct size required. Provide field manufactured duct and place into the supply and return openings in the curb. Install Gaskets The ERV roof curbs come with a gasketing package to provide a seal between the ERV unit and the top perimeter of the roof curb. Install the gasket around the top perimeter of the curb and around the supply and return opening. NOTE: Some stand-alone curbs will not have duct openings). Gasket strips must fit tightly together, leaving no gaps for leakage. IMPORTNT: Gasket installation is critical for water integrity. Improperly installed gaskets can result in air or water leaks, leading to poor unit performance. Install Roofing Materials Insulate and add a cant strip to the roof curb. Follow suggested and acceptable roofing practices END Fig. 1 ssembling the Roof Curb SIDE for applying roofing materials. The roofing material should extend up to the wood nailer and be secured under the counterflashing. Follow all local, national, and industry roofing standards. Refer to Fig. 6 for roofing recommendations. COUPLED PPLICTIONS The ERV unit can be installed directly coupled to a Carrier rooftop unit. The connection between the ERV and HVC (Heating, Ventilation, and ir Conditioning) unit is made with the use of a transition. In a coupled rooftop application there is a separate roof curb for the HVC curb and a separate roof curb for the ERV unit. See Fig. 4 and 5 for roof curb dimensions. Locate the Roof Curb Prior to locating the roof curb consider the structural support required for the rooftop system and, the duct drop location in relation to the joists. llow sufficient space for service, clearance, and locations of vents or other sources of air. Refer to the rooftop installation instructions for more information regarding location considerations. ssemble the Roof Curb Connect the curb side and the curb end. Insert the tabs on the curb end into the slots on the curb sides. Press firmly until the pieces lock in to place. It may be necessary to exert additional force to the top of the curb to lock the pieces in place. Ensure the curb pieces are locked together prior to proceeding. Repeat for other corners of the roof curb. NOTE: If lifting or moving the roof curb assembly hammer the tabs over 90 degrees. Install Deck Pans and Duct Supports The roof curb may have a duct support and deck pans, depending on the model and application. Refer to Fig. 2-5. Determine which end of the roof curb will be the duct end. Install the deck pans on the roof curb with the insulation side facing up toward the ERV base. Install the duct support between the supply and return openings. Install Locator Pieces Some ERV roof curbs (62M-CRB- 14MC and 62MB-CRB-14MC) will include locator pieces, which are to be attached to the ERV roof curb section. The locator pieces will help the installer ensure that the ERV and HVC unit roof curbs are positioned properly. ttach the 2 side locator pieces to the ERV roof curb. Install the cover panel over the 2 sides and fasten in place. 2
Set the Roof Curb Fit the roof curb assembly by measuring across the corners of the curb to ensure a square fit. Set the roof curb over the roof opening. Level the curb by placing shims under the bottom flange of the curb. Secure the curb in place by welding or fastening the curb to the roof. IMPORTNT: The ERV roof curb must be set in precisely the correct location relative to the rooftop roof curb for the transitions to connect properly. See Fig. 7-44 for location dimensions. Install Ductwork Ductwork will be installed in the roof curb for vertical, coupled applications. The duct will hang from the top of the curb. NOTE: Ductwork must be installed before the rooftop unit is set in place. NOTE: Ductwork must be installed before the ERV unit is set in place. Refer to Fig. 2 and 3 to determine the duct size required. Provide field manufactured duct and place into the supply and return openings in the curb. Install Gaskets The ERV roof curbs come with a gasketing package to provide a seal between the ERV unit and the top perimeter of the roof curb. Install the gasket around the top perimeter of the curb and around the supply and return opening. (Some stand-alone curbs will not have duct openings.) Gasket strips must fit tightly together, leaving no gaps for leakage. IMPORTNT: Gasket installation is critical for water integrity. Improperly installed gaskets can result in air or water leaks, leading to poor unit performance. Install Roofing Materials Insulate and add a cant strip to the roof curb. Follow suggested and acceptable roofing procedures for applying roofing materials. The roofing material should extend up to the wood nailer and be secured under the counter flashing. Follow all local, national, and industry roofing standards. Refer to Fig. 5 for roofing recommendations. 24.09 10.81 SUPPLY 1.00 TYP. 4X 22.94 11.50 RETURN 14.00 3.00 TYP. 4X 11.00 NOTES: 1. ll dimensions are in inches. 2. Roof curb shipped unassembled. Fig. 2 Roof Curb 62M040 for Stand-lone pplications 3
Typical Insulated deck pans. (Insulation face up) * D E S/ F C G R/ H LEGEND R/ Return ir S/ Supply ir B *IMPORTNT: Insulation on deck pans must face up. NOTE: Roof curb shipped unassembled. DIMENSIONS (in.) 62M UNIT SIZE CURB Duct Sizes PRT NO. B C D E F G H Return Supply 075,120 62M--CRB-14S 27 30.5 14 14 11.3 1 14.7 1.5 13.75 x 14.38 13.75 x 11 170-285 62M-B-CRB-14S 45.5 49.63 14 17.5 19.5 2 24 1.75 17 x 23.5 17 x 19 330-640 62M-C-CRB-14S 55.41 60.34 14 24.84 23.41 2 30 24.5 x 29.5 24.5 x 23 750,950 62M-D-CRB-14S 86.25 95.7 14 32.5 42.13 2 42.13 32 x 41.75 32 x 41.75 Fig. 3 Roof Curb 62M075-950 for Vertical Stand-lone pplications ERV Curb C B D LEGEND ERV Energy Recovery Ventilator NOTE: Roof curb shipped unassembled. 62M UNIT SIZE *62M075,120 curb is shipped with deckpans insulation and duct supports which may be discarded. 62M170-285 curb is shipped with deck pans and insulation. 4 CURB PRT NO. DIMENSIONS (in.) B C D 075,120* 62M--CRB-14S 27 30.5 14 1.5 170-285 62M-B-CRB-14S 49.63 14 45.5 1.75 330-640 62M-C-CRB-14M 60.34 14 55.41 1.75 750,950 62M-D-CRB-14M 95.7 14 86.25 1.75 Fig. 4 Roof Curb 62M075-950 for Horizontal Stand-lone pplications or s Coupled with Rooftop s 15 Tons and bove
ERV Curb C Must be Watertight Locator pieces to connect ERV curb to rooftop unit curb B D E LEGEND ERV Energy Recovery Ventilator NOTE: Roof curb shipped unassembled. 62M UNIT SIZE CURB PRT NO. DIMENSIONS (in.) B C D E 075,120 62M--CRB-14MC 30.5 14 27 1.5 19.81 170-285 62M-B-CRB-14MC 49.63 14 45.5 1.75 37.81 Fig. 5 Roof Curb 62M075-285 s 3 to 12 1 / 2 Ton Rooftop s GSKETING ROOF CURB RIGID INSULTION* CNT STRIP* ROOF DECK* NIL* FLSHING* ROOF FELT* ROOF* *Field provided. Fig. 6 Roofing Materials Recommendation 5
3.52 7.53 12.45 10.75 12.75 RETURN IR* SUPPLY IR.75 29.98 RER SIDE 2.33 19.75 RETURN IR (OPTIONL) 3.91 11.15 10.50 3.95 4.83 7.13 5.34 ERV WHEEL SUPPLY IR (OPTIONL) 45.75 19.25 OPTIONL INDOOR PREHETER 10 25.12 27.19 VIEW - RIGHT SIDE 22.90 REQUIRED SERVICE CLERNCES Front 16 in. Rear 0in. Left* 18 in. Right* 18 in. *30 in. service clearance required on either Left or Right side for ERV wheel removal. NOTE: ll dimensions are in inches. TOP SIDE 29.75 27.19 16.00 POWER ENTRY 3.95 3.48 8.43 29.88 13.26 2.67 11.09 OUTSIDE IR HORIZONTL UNITS ONLY* 29.75 25.12 OPTIONL (INDOOR) PREHETER 12.45 EXHUST IR 16.02 7.69 31.24 LEFT SIDE FRONT SIDE Fig. 7 62MB,MC040 Indoor Dimensions 13.25 16 6
13.72 OUTSIDE IR HOOD 12.29 5.35 EXHUST IR HOOD 3.55 TOP OF CURB VIEW - RIGHT SIDE 3.52 10.75 12.75 2.33 7.53 RETURN IR* 12.45 SUPPLY IR 19.75.75 29.98 RER SIDE 3.91 4.83 7.13 SUPPLY IR (OPTIONL) 10 16.00 OUTSIDE IR HOOD ND OPTIONL PREHETER 11.15 12.96 10.50 8.97 11.00 RETURN IR (OPTIONL) 3.95 5.34 ERV WHEEL 45.75 13.38 EXHUST IR HOOD TOP SIDE POWER ENTRY 29.75 16.00 3.95 3.48 OUTSIDE IR HOOD 11.09 HORIZONTL UNITS ONLY* 29.75 EXHUST IR HOOD 12.45 5.31 13.5 LEFT SIDE Fig. 8 62MD,ME040 Outdoor Dimensions REQUIRED SERVICE CLERNCES Front 27.5 in. Rear 10 in. Left* 20 in. Right* 20 in. *30 in. service clearance required on either Left or Right side for ERV wheel removal. NOTE: ll dimensions are in inches. 29.88 8.43 13.26 2.67 OUTSIDE IR 16.02 EXHUST IR 7.69 FRONT SIDE 7
5.53 18.63 5.58 12.90 21.10 VIEW - RIGHT SIDE 11.00 14.50 SUPPLY RETURN RER SIDE 6.13 10.32 SUPPLY IR (BOTTOM SUPPLY ONLY) 6.60 10.39 19.04 OPTIONL PREHETER 6.65 9.25 37.14 3.46 12.98 6.18 OPTIONL RETURN IR (BOTTOM RETURN ONLY) 10.93 TOP SIDE EXHUST IR OUTLET PREHETER CBINET REQUIRED SERVICE CLERNCES Front 31 in. Rear 0in. Left 24 in. Right* 39 in. *39 in. service clearance required for ERV wheel removal. NOTE: ll dimensions are in inches. 42.6 39.03 3.34 6.97 POWER ENTRY / OPTIONL DISCONNECT LOCTION 21.10 CCESS DOOR 15.40 EXHUST IR 18.88 (OPTIONL) IRFLOW TEST PORTS 15.25 3.88 23.00 18.63 11.00 OPTIONL PREHETER (INDOOR) 10.66 OUTSIDE IR 8.63 5.58 3.63 LEFT SIDE 2.10 10.50 FRONT SIDE Fig. 9 62MB,MC075,120 Indoor Dimensions 8
6.39 18.74 2.86 10.25 11.06 43.10 CCESS DOOR 39.8 VIEW - RIGHT SIDE 6.43 9.19 10.32 SUPPLY RETURN 3.10 14.45 RER SIDE 37.14 6.97 ERV WHEEL OUTDOOR IR HOOD 6.60 10.39 19.04.87 6.65 SUPPLY IR (BOTTOM SUPPLY ONLY) 9.25 3.46 18.69 12.98 6.18 OPTIONL PREHETER OPTIONL RETURN IR (BOTTOM RETURN ONLY) 10.93 EXHUST IR HOOD 10.35 9.60 2.87 TOP SIDE DETIL POWER ENTRY/ OPTIONL DISCONNECT *NOTE* DISCONNECT LOCTION IS PPROXIMTE 4.11 TOP OF CURB 42.60 CCESS DOOR IRFLOW TEST PORTS (OPTIONL) 18.55 13.24 5.62 SEE DETIL 9.59 LEFT SIDE Fig. 10 62MD,ME075,120 Outdoor Dimensions REQUIRED SERVICE CLERNCES Front 31 in. Rear 0in. Left 24 in. Right* 39 in. *39 in. service clearance required for ERV wheel removal. NOTE: ll dimensions are in inches. 9.60 39.03 35.711 FRONT SIDE 9
49.55 20.00 9.62 21.84 15.50 SUPPLY IR 6.92 26.60 CCESS DOOR 26.60 VIEW - RIGHT SIDE 6.48 23.00 RETURN IR RER SIDE 3.16 10.76 IRFLOW TEST PORTS (OPTIONL) 25.00 8.20 13.75 8.68 OPTIONL PREHETER 8.20 15.63 SUPPLY IR OPENING RETURN IR OPENING 22.33 6.10 15.28 EXHUST IR OUTLET 8.21 ERV WHEEL PREHETER CBINET REQUIRED SERVICE CLERNCES Front 39 in. Rear 0in. Left 32 in. Right* 55 in. TOP SIDE *55 in. service clearance required for ERV wheel removal. NOTE: ll dimensions are in inches. 62.03 14.86 POWER ENTRY (OPTIONL DISCONNECT) 26.60 57.91 22.00 CCESS DOOR OUTSIDE IR 36.00 43.38 EXHUST IR 14.57 12.50 11.18 LEFT SIDE FRONT SIDE Fig. 11 62MB,MC170-285 Indoor Dimensions 10
9.16 20.78 20.00 9.62 OUTSIDE IR HOOD VIEW - RIGHT SIDE 15.50 SUPPLY IR 6.92 RER SIDE 6.48 23.00 RETURN IR 3.16 25.00 8.20 49.55 OPTIONL PREHETER 13.75 OUTSIDE IR HOOD.64 8.68 8.20 15.63 26.45 SUPPLY IR OPENING 22.33 6.10 ERV WHEEL 15.28 8.21 RETURN IR OPENING EXHUST IR HOOD 16.19 TOP SIDE 62.03 14.86 POWER ENTRY (OPTIONL DISCONNECT) 14.84 EXHUST IR 15.96 43.38 14.57 6.94 12.50 LEFT SIDE Fig. 12 62MD,ME170-285 Outdoor Dimensions REQUIRED SERVICE CLERNCES Front 39 in. Rear 0in. Left 32 in. Right* 55 in. *55 in. service clearance required for ERV wheel removal. NOTE: ll dimensions are in inches. 57.91 OUTSIDE IR HOOD 4.61 TOP OF CURB EXHUST IR HOOD FRONT SIDE 11
29.00 14.63 CCESS DOOR 65.21 VIEW - RIGHT SIDE 19.00 7.66 28.50 SUPPLY IR RETURN IR 37.50 6.11 6.61 2.87 RER SIDE 37.50 6.11 OPTIONL PREHETER 15.94 6.88 8.01 18.62 SUPPLY IR OPENING (BOTTOM SUPPLY ONLY) PREHETER CBINET 25.76 REQUIRED SERVICE CLERNCES RETURN IR OPENING (BOTTOM RETURN ONLY) 6.93 21.11 EXHUST IR OUTLET Front 50 in. Rear 0in. Left 40 in. Right* 62 in. *62 in. service clearance required for ERV wheel removal. TOP SIDE NOTE: ll dimensions are in inches. OPTIONL IRFLOW TEST PORTS 72.63 17.00 POWER ENTRY (OPTIONL DISCONNECT) 29.00 67.39 5.11 27.00 CCESS DOOR OUTSIDE IR 54.00 49.1 EXHUST IR 9.03 2.78 20.00 LEFT SIDE FRONT SIDE Fig. 13 62MB,MC330-640 Indoor Dimensions 12
OUTSIDE IR HOOD 8.68 26.41 VIEW - RIGHT SIDE 19.00 7.66 28.50 SUPPLY IR RETURN IR 37.50 6.11 6.61 RER SIDE 2.87 15.94 6.88 8.01 18.62 29.44 65.21 SUPPLY IR OPENING (BOTTOM SUPPLY ONLY) OUTSIDE IR HOOD 25.76 OPTIONL PREHETER 6.93 RETURN IR OPENING (BOTTOM RETURN ONLY) 21.11 EXHUST IR HOOD 19.69 7.63 TOP SIDE OPTIONL IRFLOW TEST PORTS 72.63 17.00 POWER ENTRY (OPTIONL DISCONNECT) 37.50 49.1 EXHUST IR 17.96 12.52 6.11 9.22 EXHUST IR HOOD 20.00 LEFT SIDE Fig. 14 62MD,ME330-640 Outdoor Dimensions 18.81 REQUIRED SERVICE CLERNCES Front 50 in. Rear 0in. Left 40 in. Right* 62 in. *62 in. service clearance required for ERV wheel removal. NOTE: ll dimensions are in inches. 67.39 OUTSIDE IR HOOD 4.21 TOP OF CURB FRONT SIDE 13
RIGHT SIDE SUPPLY IR 40 7.69 13.11 28.00 16.19 34.10 CCESS DOOR 21.86 VIEW - RETURN IR 35.75 RER SIDE 77.41 49.01 7.69 6.42 18.75 17.07 OPTIONL PREHETER 11.02 21.88 40.12 SUPPLY IR OPENING RETURN IR OPENING 34.73 6.43 31.67 EXHUST IR OUTLET 34 7/8 PREHETER CBINET REQUIRED SERVICE CLERNCES Front 65 in. Rear 0in. Left 50 in. Right* 72 in. *72 in. service clearance required for ERV wheel removal. NOTE: ll dimensions are in inches. TOP SIDE IRFLOW TEST PORTS (OPTIONL) 107.75 23.25 POWER ENTRY/ OPTIONL DISCONNECT LOCTION 34.10 CCESS DOOR 98.37 12.77 35.08 OUTSIDE IR 64.25 20.25 EXHUST IR 48.98 9.52 9.01 2.37 11.31 LEFT SIDE FRONT SIDE Fig. 15 62MB,MC750,950 Indoor Dimensions 14
8.83 OUTSIDE IR HOOD 33.71 VIEW - RIGHT SIDE SUPPLY IR 40 28.00 16.19 7.69 13.11 RER SIDE RETURN IR 35.75 B 49.01 7.69 77.41 4.40 OUTSIDE IR HOOD 18.75 11.02 6.42 17.07 21.88 40.12 SUPPLY IR OPENING 34.73 OPTIONL PREHETER 6.43 34 7/8 31.67 RETURN IR OPENING EXHUST IR HOOD 23.22 17.16 TOP SIDE IRFLOW TEST PORTS (OPTIONL) POWER ENTRY/ OPTIONL DISCONNECT LOCTION 107.75 23.25 23.81 21.58 20.25 EXHUST IR 48.98 9.01 2.89 LEFT SIDE Fig. 16 62MD,ME750,950 Outdoor Dimensions REQUIRED SERVICE CLERNCES Front 65 in. Rear 0in. Left 50 in. Right* 72 in. *72 in. service clearance required for ERV wheel removal. NOTE: ll dimensions are in inches. 98.37 OUTSIDE IR HOOD EXHUST IR HOOD FRONT SIDE 15
Filter access door shipped with Rooftop Rooftop 62M040 Outside air hood with aluminum water entrainment filter. Includes barometric intake damper. Exhaust hood Filter Filters Evaporation Coil EXH ccessory ERV Equipment support TRNSITION DETIL Standard Rooftop roof curb Outside air hood Filter ERV wheel Supply Blower 3 to 6 Ton Rooftop Panel covering return chamber ccessory Transition 3 ROOF CURB LOCTION DETIL Supply ccess door to adjust balancing damper Balancing damper To 62M040 Return ccessory ERV Equipment support 35 67 3/8 Rooftop Curb 35" ERV Support Side View - Rooftop Curb Top View 37 LEGEND ERV Energy Recovery Ventilator ROOFTOP UNIT MODEL ROOFTOP SIZE TRNSITION P/N ROOFTOP ECONOMIZER ERV EQUIPMENT SUPPORT P/N 48/50HJ,TJ,TM 004-007 62M-TR-HJ36-D 62M-900---004 62M-900---001 Fig. 17 62MD,ME040 Coupled with Carrier 48/50HJ,TJ,TM004-007 Vertical Discharge Rooftop 16
Filter access door shipped with Rooftop Rooftop 62M040 Field-Supplied Duct Outside air hood with aluminum water entrainment filter. Includes barometric intake damper. Exhaust hood Filter EXH ccessory ERV Equipment support TRNSITION DETIL Standard Rooftop roof curb Supply Blower 3 to 6 Ton Rooftop Panel covering return chamber Outside air hood Filter ERV wheel ccessory Transition ROOF CURB LOCTION DETIL 3 Supply ccess door to adjust balancing damper Balancing damper To 62M040 Return ccessory ERV Equipment support 35 67 3/8 Rooftop Curb 35" ERV Support Side View - Rooftop Curb 37 LEGEND ERV Energy Recovery Ventilator ROOFTOP UNIT MODEL ROOFTOP SIZE TRNSITION P/N ROOFTOP ECONOMIZER ERV EQUIPMENT SUPPORT P/N 48/50HJ,TJ,TM 004-007 62M-TR-HJ36-D 62M-900---008 62M-900---001 Fig. 18 62MD,ME040 Coupled with Carrier 48/50HJ,TJ,TM004-007 Horizontal Discharge Rooftop 17
Rooftop ccessory Transition (Includes front panel) Rooftop Supply Return TRNSITION DETIL ccessory ERV Equipment support Filter Exhaust hood ccessory Transition ERV wheel Filter 62M040 2 Piece front panel covers return chamber Outside air hood Top View ROOF CURB LOCTION DETIL 80 5/16 35 ccess door to adjust balancing damper To 62M040 44 11/16 Supply Return 4 3/8 Rooftop Curb 35" ERV Support Rooftop Curb LEGEND ERV Energy Recovery Ventilator ccessory ERV Equipment support Side View - ROOFTOP UNIT MODEL ROOFTOP SIZE TRNSITION P/N ERV EQUIPMENT SUPPORT P/N 48/50PG 03-07 62M-TR-HJ36-D 62M-900---001 Fig. 19 62MD,ME040 Coupled with Carrier 48/50PG03-07 Vertical Discharge Rooftop 18
Rooftop ccessory Transition (Includes front panel) Rooftop TRNSITION DETIL ccessory ERV Equipment support Filter ccessory Transition ERV wheel Filter 62M040 2 Piece front panel covers return chamber Exhaust hood Outside air hood Top View ROOF CURB LOCTION DETIL 80 5/16 35 ccess door to adjust balancing damper To 62M040 44 11/16 4 3/8 Rooftop Curb 35" ERV Support Rooftop Curb LEGEND ERV Energy Recovery Ventilator ccessory ERV Equipment support Side View - ROOFTOP UNIT MODEL ROOFTOP SIZE TRNSITION P/N ERV EQUIPMENT SUPPORT P/N 48/50PG 03-07 62M-TR-HJ36-D 62M-900---001 Fig. 20 62MD,ME040 Coupled with Carrier 48/50PG03-07 Horizontal Discharge Rooftop 19
ROOF CURB LYOUT TOP VIEW 67 3/8" Supply ir Standard roof curb for 3 to 6 ton rooftop unit 37 3/16" Return ir 35 " 3" 36" 34 3/8" 62M-900---001 Equipment Support "-" SIDE VIEW Standard Roof curb for 3 to 6 ton roof top unit 35 " 62M-900---001 Equipment Support 14" 10.4" Roof Fig. 21 62MD,ME040 Coupled with Carrier 48/50HJ,TJ,TM004-007 Rooftop 20
Filter door shipped with Rooftop unit. Rainhoods for optional economizer 62M ERV Rooftop unit Rooftop unit curb ccessory Transition SUPPLY RETURN ERV Wheel 62M075,120 ERV Locator pieces (included with ERV curb ERV curb, must be watertight) ROOF CURB LOCTION DETIL B Rooftop curb Locator Pieces ( included with ERV Curb) Cover panel provided 30.5 LEGEND ERV Energy Recovery Ventilator 27 NOTE: When using a 62M ERV unit coupled with a Carrier rooftop unit, the rooftop factory or field-installed economizer cannot be used. Use the 62M economizer instead. 2 3/4" 20" ERV curb ROOFTOP UNIT MODEL 48/50HJ,TF,TJ,TM ROOFTOP SIZE TRNSITION P/N ERV CURB P/N ROOFTOP ECONOMIZER DIMENSIONS (in.) B 004-007 62M-TR-HJ36-D 62M--CRB-14MC 62M-900---004 67 3 / 8 37 3 / 16 008,009 62M-TR-HJ78-D 62M--CRB-14MC 62M-900---005 78 1 / 4 50 012,014 62M-TR-HJ1012-D 62M--CRB-14MC 62M-900---006 78 1 / 4 50 Fig. 22 62MD,ME075,120 Coupled with Carrier 48/50HJ,TF,TJ,TM004-014 Vertical Discharge Rooftop 21
Filter door shipped with Rooftop unit. Horizontal supply and return duct (field supplied) 62M ERV Rooftop Rooftop unit ccessory Transition ERV Wheel 62M075,120 ERV Locator pieces (included with ERV curb ERV curb, must be watertight) Optional Horizontal Economizer ROOF CURB LOCTION DETIL B Rooftop curb Locator Pieces ( included with ERV curb) Cover panel provided 30.5" 27" LEGEND ERV Energy Recovery Ventilator NOTE: When using a 62M ERV unit coupled with a Carrier rooftop unit, the rooftop factory or field-installed economizer cannot be used. Use the 62M economizer instead. 2 3/4" 20" ERV curb ROOFTOP UNIT MODEL 48/50HJ,TF,TJ,TM ROOFTOP SIZE TRNSITION P/N ERV CURB P/N ROOFTOP ECONOMIZER DIMENSIONS (in.) B 004-007 62M-TR-HJ36-H 62M--CRB-14MC 62M-900---008 67 3 / 8 37 3 / 16 008,009 62M-TR-HJ78-H 62M--CRB-14MC 62M-900---009 78 1 / 4 50 012,014 62M-TR-HJ1012-H 62M--CRB-14MC 62M-900---010 78 1 / 4 50 Fig. 23 62MD,ME075,120 Coupled with Carrier 48/50HJ,TF,TJ,TM004-014 Horizontal Discharge Rooftop 22
Rooftop Rooftop ccessory Transition (Includes front panel) 62M ERV Supply Return ERV Wheel TOP VIEW ccessory Transition 62M075,120 ERV Locator pieces (included with ERV Curb ERV curb, must be watertight) LEGEND ERV Energy Recovery Ventilator NOTE: When using a 62M ERV unit coupled with a Carrier rooftop unit, the rooftop factory or field-installed economizer cannot be used. ROOF CURB LOCTION DETIL 20" 30 1/12" ERV Curb B Supply Return 2 3/4" 27" Rooftop Curb Curb Detail 20" ERV Curb Rooftop Curb Side View - Locator pieces (included with ERV Curb) ROOFTOP MODEL ROOFTOP SIZE 62M TRNSITION ERV CURB 48/50PG DIMENSIONS (in.) B 03-07 62M-TR-PG26-D 62M--CRB-14MC 80 5 / 16 44 11 / 16 08-14 62M-TR-PG712-D 62M--CRB-14MC 92 3 / 4 53 15 / 16 Fig. 24 62MD,ME075,120 Coupled with Carrier 48/50PG03-14 Vertical Discharge Rooftop 23
Rooftop Rooftop ccessory Transition (Includes front panel) 62M ERV Wheel TOP VIEW ccessory Transition 62M075-120 ERV Locator pieces (included with ERV curb, must be watertight) ERV Curb LEGEND ERV Energy Recovery Ventilator NOTE: When using a 62M ERV unit coupled with a Carrier rooftop unit, the rooftop factory or fieldinstalled economizer cannot be used. ROOF CURB LOCTION DETIL 20" ERV Curb 30 1/12" Curb Detail B 2 3/4" 27" Rooftop Curb 20" ERV Curb Rooftop Curb Locator pieces (included with ERV Curb) Side View - ROOFTOP MODEL ROOFTOP SIZE 62M TRNSITION ERV CURB 48/50PG DIMENSIONS (in.) B 03-07 62M-TR-PG26-H 62M--CRB-14MC 80 5 / 16 44 11 / 16 08-14 62M-TR-PG712-H 62M--CRB-14MC 92 3 / 4 53 15 / 16 Fig. 25 62MD,ME075,120 Coupled with Carrier 48/50PG03-14 Horizontal Discharge Rooftop 24
Filter door shipped with Rooftop unit 62M ERV Rainhoods for optional economizer Rooftop unit Rooftop Top View Rooftop curb Locator Pieces (included with ERV curb, must be watertight) ERV Curb 30 ccessory Transition 62M170-285 ERV SUPPLY RETURN ERV Wheel B Rooftop curb ROOF CURB LOCTION DETIL Locator Pieces ( included with ERV curb) Cover panel provided 49 5/8" ERV curb 45 1/2" 2 3/4" 38" Top View LEGEND ERV Energy Recovery Ventilator NOTE: When using a 62M ERV unit coupled with a Carrier rooftop unit, the rooftop factory or field-installed economizer cannot be used. Use the 62M economizer instead. ROOFTOP UNIT MODEL 48/50HJ,TF,TJ,TM ROOFTOP SIZE TRNSITION P/N ERV CURB P/N ROOFTOP ECONOMIZER DIMENSIONS (in.) B 004-007 62M-BTR-HJ36-D 62M-B-CRB-14MC 62M-900---004 67 3 / 8 37 3 / 16 008,009 62M-BTR-HJ78-D 62M-B-CRB-14MC 62M-900---005 78 1 / 4 50 012,014 62M-BTR-HJ1012-D 62M-B-CRB-14MC 62M-900---006 78 1 / 4 50 Fig. 26 62MD,ME170-285 Coupled with Carrier 48/50HJ,TF,TJ,TM004-014 Vertical Discharge Rooftop 25
Optional Horizontal Economizer Rooftop Filter door shipped with Rooftop unit. 62M ERV Rooftop Top View Horizontal Return duct (field supplied) Locator pieces (included with ERV curb, must be watertight) ERV Curb 30" ccessory Transition 62M170-285 ERV ERV Wheel B Rooftop curb ROOF CURB LOCTION DETIL Locator Pieces ( included with ERV Curb) Cover Panel provided 49 5/8" ERV curb 45 1/2" 2 3/4" 38" Top View LEGEND ERV Energy Recovery Ventilator NOTE: When using a 62M ERV unit coupled with a Carrier rooftop unit, the rooftop factory or field-installed economizer cannot be used. Use the 62M economizer instead. ROOFTOP UNIT MODEL 48/50HJ,TF,TJ,TM ROOFTOP SIZE TRNSITION P/N ERV CURB P/N ROOFTOP ECONOMIZER DIMENSIONS (in.) B 004-007 62M-BTR-HJ36-H 62M-B-CRB-14MC 62M-900---008 67 3 / 8 37 3 / 16 008,009 62M-BTR-HJ78-H 62M-B-CRB-14MC 62M-900---009 78 1 / 4 50 012,014 62M-BTR-HJ1012-H 62M-B-CRB-14MC 62M-900---010 78 1 / 4 50 Fig. 27 62MD,ME170-285 Coupled with Carrier 48/50HJ,TF,TJ,TM004-014 Horizontal Discharge Rooftop 26
Rooftop ccessory Transition 62M ERV unit LEGEND ERV Energy Recovery Ventilator NOTES: 1. The 62M ERV unit cannot be coupled with horizontal return 48/50TJ,TM016-028 and 48/50HJ015,017 units. 2. The ERV unit can be used with a factoryinstalled economizer, if desired. curb ERV curb TOP VIEW SIDE VIEW Rooftop ccessory Transition 62M170-285 ERV 15 to 25 Ton Rooftop 62M170-285 ERV ERV Wheel *Optional Economizer Transition Rooftop Curb ROOF CURB LOCTION DETIL ERV Curb 74 1/4" SUPPLY RETURN 45 1/2" Rooftop Curb 44 3/4" ERV Curb 18 11/16" 49 5/8" 67 1/16"* 44 3/4" TOP VIEW *Length is 89 1 / 16 for 48/50TM028 units. SIDE VIEW - ROOFTOP UNIT MODEL ROOFTOP SIZE TRNSITION P/N ERV CURB P/N 48/50TJ,TM 016-028 62M-BTR-HJ1525-D 62M-B-CRB-14S 48/50HJ 015,017 62M-BTR-HJ1525-D 62M-B-CRB-14S Fig. 28 62MD,ME170-285 Coupled with Carrier 48/50TJ,TM016-028 and 48/50HJ015,017 Vertical Discharge Rooftop 27
Rooftop Rooftop ccessory Transition (Includes front panel) 62M ERV Supply Return ERV Wheel TOP VIEW ccessory Transition 62M170-285 ERV Locator pieces (included with ERV curb, must be watertight) ERV Curb LEGEND ERV Energy Recovery Ventilator NOTE: When using a 62M ERV unit coupled with a Carrier rooftop unit, the rooftop factory or field-installed economizer cannot be used. ROOF CURB LOCTION DETIL 38 3/4" 49 5/8" ERV Curb Curb Detail B Supply Return 45 1/2" Rooftop Curb 38 3/4" ERV Curb Rooftop Curb 0" Side View - Locator pieces (included with ERV Curb) ROOFTOP MODEL ROOFTOP SIZE 62M TRNSITION ERV CURB 48/50PG DIMENSIONS (in.) B 03-07 62M-BTR-PG26-D 62M--CRB-14MC 80 5 / 16 44 11 / 16 08-14 62M-BTR-PG712-D 62M--CRB-14MC 92 3 / 4 53 15 / 16 Fig. 29 62MD,ME170-285 Coupled with Carrier 48/50PG03-14 Vertical Discharge Rooftop 28
Rooftop Rooftop ccessory Transition (Includes front panel) 62M ERV ccessory Transition ERV Wheel TOP VIEW 62M170-285 ERV Locator pieces (included with ERV curb, ERV Curb must be watertight) LEGEND ERV Energy Recovery Ventilator NOTE: When using a 62M ERV unit coupled with a Carrier rooftop unit, the rooftop factory or field-installed economizer cannot be used. ROOF CURB LOCTION DETIL 38 3/4" ERV Curb 49 5/8" Curb Detail B 45 1/2" Rooftop Curb 38 3/4" ERV Curb Rooftop Curb 0" Side View - Locator pieces (included with ERV Curb) ROOFTOP MODEL ROOFTOP SIZE 62M TRNSITION ERV CURB 48/50PG DIMENSIONS (in.) B 03-07 62M-BTR-PG26-H 62M-B-CRB-14MC 80 5 / 16 44 11 / 16 08-14 62M-BTR-PG712-H 62M-B-CRB-14MC 92 3 / 4 53 15 / 16 Fig. 30 62MD,ME170-285 Coupled with Carrier 48/50PG03-14 Horizontal Discharge Rooftop 29
Rooftop Outside ir Hood (See Note 2) 62M ERV Rooftop Curb Horizontal / Return Duct (field supplied) Rooftop ccessory Transition ccessory Transition 62M170-285 ERV ERV Curb Top View ERV Wheel Relief Hood O/ Hood LEGEND ERV Energy Recovery Ventilator O/ Outdoor ir NOTES: 1. The ERV unit can be used with a factoryinstalled economizer, if desired. 2. Transition includes a new outside air hood, which allows air intake through the front of the hood rather than the bottom. The new hood will use the filters from the original rooftop unit hood. ROOF CURB LOCTION DETIL Rooftop Curb 44 3/4 49 5/8 ERV Curb Curb Detail B 45 1/2 Rooftop Curb 44 3/4" ERV Curb Side View - Top View ROOFTOP MODEL ROOFTOP SIZE 62M TRNSITION ERV CURB DIMENSIONS (in.) B 48/50PG 20-28 62M-BTR-HG1525-H 62M-B-CRB-14MC 114.4 78.6 48/50HJ 020-028 62M-BTR-HG1525-H 62M-B-CRB-14MC 114.4 78.6 Fig. 31 62MD,ME170-285 Coupled with Carrier 48/50PG20-28 and 48/50HJ020-028 Horizontal Discharge Rooftop 30
Rooftop Outside ir Hood (See Note 2) 62M ERV Rooftop Standard HVC Roofcurb ccessory Transition ccessory Transition 62M170-285 ERV ERV Curb SUPPLY RETURN ERV Wheel O/ Hood LEGEND ERV Energy Recovery Ventilator O/ Outdoor ir NOTES: 1. The ERV unit can be used with a factoryinstalled economizer, if desired. 2. Transition includes a new outside air hood, which allows air intake through the front of the hood rather than the bottom. The new hood will use the filters from the original rooftop unit hood. Top View Relief Hood Rooftop Curb ROOF CURB LOCTION DETIL 44 3/4 49 5/8 Curb Detail B SUPPLY RETURN 45 1/2 Rooftop Curb 44 3/4" ERV Curb ERV Curb Side View - Top View ROOFTOP MODEL ROOFTOP SIZE 62M TRNSITION ERV CURB DIMENSIONS (in.) B 48/50PG 20-28 62M-BTR-HG1525-D 62M-B-CRB-14MC 114.4 78.6 48/50HJ 020-028 62M-BTR-HG1525-D 62M-B-CRB-14MC 114.4 78.6 Fig. 32 62MD,ME170-285 Coupled with Carrier 48/50PG20-28 and 48/50HJ020-028 Vertical Discharge Rooftop 31
Filter access door shipped with transition 62M ERV Rooftop Outside air hood for optional economizer Top View ccessory Transition Rooftop ccessory Transition 62M330-640 ERV ERV Curb Supply Return ERV Wheel O/ hood LEGEND ERV Energy Recovery Ventilator O/ Outdoor ir NOTE: When using a 62M ERV unit coupled with a Carrier rooftop unit, the rooftop factory or fieldinstalled economizer cannot be used. Use the 62M economizer instead. Outside air hood for optional economizer Rooftop curb Exhaust hood ROOF CURB LOCTION DETIL ERV curb 78 1/4" Supply Return 55 13/32" Rooftop Curb 33 1/2" ERV Curb 50" 9" 33 1/2" 60 11/32" Side View - Top View ROOFTOP UNIT MODEL ROOFTOP SIZE TRNSITION P/N ERV CURB P/N ROOFTOP ECONOMIZER 48/50HJ,TF,TJ,TM 012,014 62M-CTR-HJ1012-D 62M-C-CRB-14M 62M-900---006 Fig. 33 62MD,ME330-640 Coupled with Carrier 48/50HJ,TF,TJ,TM012,014 Vertical Discharge Rooftop 32
Rooftop Filter access door shipped with transition 62M ERV LEGEND ERV Energy Recovery Ventilator O/ Outdoor ir R/ Return ir S/ Supply ir NOTE: When using a 62M ERV unit coupled with a Carrier rooftop unit, the rooftop factory or field-installed economizer cannot be used. Use the 62M economizer instead. Rooftop Top View ccessory Transitions Horizontal supply duct (field supplied) Horizontal return (field supplied) 62M330-640 ERV ccessory Transition 10 to 12 1/2 Ton Rooftop ccessory Transitions ERV Curb Top View with Economizer 62M 330-640 ERV ERV Wheel O/ hood S/ R/ Exhaust hood S/ Duct R/ Duct Optional Horizontal Economizer Exhaust hood Rooftop curb ROOF CURB LOCTION DETIL ERV Curb 78 1/4" 55 13/32" Rooftop Curb 33 1/2" ERV Curb 50" 9" 33 1/2" 60 11/32" Side View - Top View ROOFTOP UNIT MODEL ROOFTOP SIZE TRNSITION P/N ERV CURB P/N ROOFTOP ECONOMIZER 48/50HJ,TF,TJ,TM Without Economizer 012,014 62M-CTR-HJ1012-H 62M-C-CRB-14M 48/50HJ,TF,TJ,TM With Economizer 012,014 62M-CTR-HJ1012-HEC 62M-C-CRB-14M 62M-900---010 Fig. 34 62MD,ME330-640 Coupled with Carrier 48/50HJ,TF,TJ,TM012,014 Horizontal Discharge Rooftop 33
Rooftop LEGEND ERV Energy Recovery Ventilator O/ Outdoor ir NOTES: 1. The ERV unit can be used with a factoryinstalled economizer, if desired. 2. The ERV cannot be coupled with a horizontal return 48/50TJ,TM or HJ 15 to 25 ton rooftop unit. 62M ERV Rooftop Curb ccessory Transition ERV curb Rooftop ccessory Transition 62M330-640 ERV TJ/HJ 15 to 25 Ton Rooftop ccessory Transition 62M ERV SUPPLY RETURN ERV Wheel Optional Economizer O/ hood Exhaust hood Top View Side View Rooftop Curb ROOF CURB LOCTION DETIL ERV curb 74 1/4" SUPPLY IR RETURN IR 55 13/32" Rooftop Curb 53 3/4" ERV Curb 11 1/2" 67 1/16"* 53 3/4" 60 11/32" Side View - Top View *Length is 89 1 / 16 for 48/50TM028 units. ROOFTOP UNIT MODEL ROOFTOP SIZE TRNSITION P/N ERV CURB P/N 48/50TJ,TM 016-028 62M-BTR-HJ1525-D 62M-B-CRB-14S 48/50HJ 015,017 62M-BTR-HJ1525-D 62M-B-CRB-14S Fig. 35 62MD,ME330-640 Coupled with Carrier 48/50TJ,TM016-028 and 48/50HJ015,017 Vertical Discharge Rooftop 34
Rooftop Rooftop 48/50PG ccessory Transition (Includes front panel) 62M ERV Supply Return ccessory Transition ERV Wheel TOP VIEW 62M330-640 ERV LEGEND ERV Energy Recovery Ventilator ERV Curb NOTE: When using a 62M ERV unit coupled with a Carrier rooftop unit, the rooftop factory or field-installed economizer cannot be used. ROOF CURB LOCTION DETIL 38 3/4 " 60 11/32" ERV Curb Curb Detail B Supply Return 55 13/32" Rooftop Curb 38 3/4" ERV Curb Rooftop Curb C Side View - ROOFTOP UNIT DIMENSIONS (in.) ROOFTOP SIZE 62M TRNSITION ERV CURB MODEL B C 48/50PG 08-14 62M-CTR-PG712-D 62M-C-CRB-14M 92 3 / 4 53 15 / 16 10 Fig. 36 62MD,ME330-640 Coupled with Carrier 48/50PG08-14 Vertical Discharge Rooftop 35
Rooftop Rooftop ccessory Transition (Includes front panel) 62M ERV ccessory Transition ERV Wheel TOP VIEW 62M330-640 ERV ERV Curb LEGEND ERV Energy Recovery Ventilator NOTE: When using a 62M ERV unit coupled with a Carrier rooftop unit, the rooftop factory or field-installed economizer cannot be used. ROOF CURB LOCTION DETIL 38 3/4" 60 11/32" ERV Curb Curb Detail B C 55 13/32" Rooftop Curb 38 3/4" ERV Curb Rooftop Curb Side View - ROOFTOP UNIT DIMENSIONS (in.) ROOFTOP SIZE 62M TRNSITION ERV CURB MODEL B C 48/50PG 08-14 62M-CTR-PG712-H 62M-C-CRB-14M 92 3 / 4 53 15 / 16 10 Fig. 37 62MD,ME330-640 Coupled with Carrier 48/50PG08-14 Horizontal Discharge Rooftop 36
Rooftop Outside ir Hood (See Note 2) 62M ERV Horizontal Return Duct (Field Supplied) Rooftop ccessory Transition Rooftop Curb ccessory Transition 62M330-640 ERV ERV Curb Top View ERV Wheel Relief Hood O/ Hood LEGEND ERV Energy Recovery Ventilator O/ Outdoor ir NOTES: 1. The ERV unit can be used with a factoryinstalled economizer, if desired. 2. Transition includes a new outside air hood, which allows air intake through the front of the hood rather than the bottom. The new hood will use the filters from the original rooftop unit hood. Rooftop Curb ROOF CURB LOCTION DETIL 44 3/4" 60 11/32" Curb Detail B 55 13/32" Rooftop Curb 44 3/4" ERV Curb Side View - ERV Curb Top View ROOFTOP MODEL ROOFTOP SIZE 62M TRNSITION ERV CURB DIMENSIONS (in.) B 48/50PG 20-28 62M-CTR-HG1525-H 62M-C-CRB-14M 114.4 78.6 48/50HJ 020-028 62M-CTR-HG1525-H 62M-B-CRB-14M 114.4 78.6 Fig. 38 62MD,ME330-640 Coupled with Carrier 48/50PG20-28 and 48/50HJ020-028 Horizontal Discharge Rooftop 37
Rooftop Outside ir Hood (See Note 2) 62M ERV Rooftop Curb Rooftop ccessory Transition ccessory Transition ERV Curb 62M330-640 ERV SUPPLY RETURN Top View ERV Wheel O/ Hood LEGEND ERV Energy Recovery Ventilator O/ Outdoor ir NOTES: 1. The ERV unit can be used with a factoryinstalled economizer, if desired. 2. Transition includes a new outside air hood, which allows air intake through the front of the hood rather than the bottom. The new hood will use the filters from the original rooftop unit hood. Relief Hood ROOF CURB LOCTION DETIL Rooftop Curb 44 3/4" 60 11/32" Curb Detail B SUPPLY RETURN 55 13/32" Rooftop Curb 44 3/4" ERV Curb ERV Curb Side View - Top View ROOFTOP MODEL ROOFTOP SIZE 62M TRNSITION ERV CURB DIMENSIONS (in.) B 48/50PG 20-28 62M-CTR-HG1525-D 62M-C-CRB-14M 114.4 78.6 48/50HJ 020-028 62M-CTR-HG1525-D 62M-B-CRB-14M 114.4 78.6 Fig. 39 62MD,ME330-640 Coupled with Carrier 48/50PG20-28 and 48/50HJ020-028 Vertical Discharge Rooftop 38
TOP VIEW ccessory Transition 62M ERV Supply Return ERV Wheel O/ hood Exhaust hood Rooftop ROOF CURB L YOUT 60.34" 0" LEGEND ERV Energy Recovery Ventilator O/ Outdoor ir NOTES: 1. The ERV unit can be used with a factoryinstalled economizer, if desired. 2. ERV cannot be coupled to a horizontal return rooftop unit. Supply Return 58 3/4" ERV Curb 55.4" Rooftop Curb 77 3/4" Outside air hood 62M SIDE VIEW Rooftop Economizer See Note 1 ERV Wheel ERV Curb ccessory Transition Standard Rooftop Curb ROOFTOP UNIT MODEL ROOFTOP SIZE TRNSITION P/N ERV CURB P/N 48/50 020-060 62M-CTR-J2060-D 62M-C-CRB-14M Fig. 40 62MD,ME330-640 Coupled with Carrier 48/50020-060 Vertical Discharge Rooftop 39
Rooftop 62M ERV Top View Rooftop Curb ccessory Transition Rooftop ccessory Transition 62M750,950 ERV ERV Curb SUPPLY RETURN ERV Wheel O/ Hood LEGEND ERV Energy Recovery Ventilator O/ Outdoor ir Exhaust Hood NOTES: 1. The standard factory economizer cannot be used when coupled with 62M750,950 units. Contact factory for transition with economizer. 2. 62M750,950 units cannot be used with 48/50TJ and TM016-028 horizontal discharge rooftop units. ROOF CURB LOCTION DETIL Rooftop Curb ERV Curb 74 1/4" SUPPLY IR RETURN IR 0" Rooftop 86.25" 31 9/16" Curb ERV Curb 67.1"* 31 9/16" 95.7" Side View - *Length is 89 1 / 16 for 48/50TM028 units. Top View ROOFTOP UNIT MODEL ROOFTOP SIZE TRNSITION P/N ERV CURB P/N ROOFTOP ECONOMIZER 48/50TJ,TM 016-028 62M-DTR-HJ1525-D 62M-D-CRB-14M 62M-900---007 48/50HJ 015,017 62M-DTR-HJ1525-D 62M-D-CRB-14M 62M-900---007 Fig. 41 62MD,ME750,950 Coupled with Carrier 48/50TJ,TM016-028 and 48/50HJ015,017 Vertical Discharge Rooftop 40
Rooftop 62M ERV Rooftop ccessory Transition ccessory Transition 62M750,950 ERV ERV Wheel O/ Hood ERV Curb LEGEND ERV Energy Recovery Ventilator O/ Outdoor ir NOTE: The ERV unit can be used with a factoryinstalled economizer, if desired. Top View Relief Hood ROOF CURB LOCTION DETIL ERV Curb Curb Detail B 86 1/4" Rooftop Curb 44 3/4" ERV Curb 44 3/4 95 3/4" Side View - Top View ROOFTOP MODEL ROOFTOP SIZE 62M TRNSITION ERV CURB DIMENSIONS (in.) B 48/50PG 20-28 62M-DTR-HG1525-H 62M-D-CRB-14M 114.4 78.6 48/50HJ 020-028 62M-DTR-HG1525-H 62M-D-CRB-14M 114.4 78.6 Fig. 42 62MD,ME750,950 Coupled with Carrier 48/50PG20-28 and 48/50HJ020-028 Vertical Discharge Rooftop 41
Rooftop 62M ERV Rooftop Curb Rooftop ccessory Transition ccessory Transition 62M750,950 ERV ERV Curb SUPPLY RETURN ERV Wheel O/ Hood LEGEND ERV Energy Recovery Ventilator O/ Outdoor ir NOTE: The ERV unit can be used with a factory-installed economizer, if desired. Top View Relief Hood ROOF CURB LOCTION DETIL Rooftop Curb ERV Curb Curb Detail B SUPPLY RETURN 86 1/4" Rooftop Curb 44 3/4" ERV Curb Top View 44 3/4 95 3/4" Side View - ROOFTOP MODEL ROOFTOP SIZE 62M TRNSITION ERV CURB DIMENSIONS (in.) B 48/50PG 20-28 62M-DTR-HG1525-D 62M-D-CRB-14M 114.4 78.6 48/50HJ 020-028 62M-DTR-HG1525-D 62M-D-CRB-14M 114.4 78.6 Fig. 43 62MD,ME750,950 Coupled with Carrier 48/50PG20-28 and 48/50HJ020-028 Vertical Discharge Rooftop 42
Rooftop 62M ERV Rooftop curb ccessory Transition ccessory Transition 62M750,950 ERV O/ Hood ERV Curb RETURN IR SUPPLY IR ERV Wheel LEGEND ERV Energy Recovery Ventilator O/ Outdoor ir NOTES: 1. The standard factory economizer can be used in conjunction with 62M750,950 units. 2. 62M750,950 units cannot be used with horizontal discharge rooftop units. Exhaust Hood ROOF CURB LOCTION DETIL Rooftop Curb 0" ERV Curb CURB DETIL SUPPLY IR RETURN IR 86.25" Rooftop Curb 57 9/16" ERV Curb 57 9/16" (See curb detail) 95.7" Side View - 77 3/4" Top View ROOFTOP UNIT MODEL ROOFTOP SIZE TRNSITION P/N ERV CURB P/N 48/50 020-060 62M-DTR-J2060-D 62M-D-CRB-14M Fig. 44 62MD,ME750,950 Coupled with Carrier 48/50020-060 Rooftop 43
Exhaust hood (outdoor units only) Top View Horizontal Discharge - Stand-lone Outside air hood (outdoor units only) Optional Pre-heater Exhaust Blower 2 in. pre-filters for exhaust 2 in. pre-filters for outside air ERV wheel Supply air blower Exhaust hood (outdoor units only) ERV Wheel 2 in. pre-filters exhaust Return/exhaust opening in base Top View Down Discharge - Stand-lone Optional Pre-heater Exhaust blower Outside air blower, mounted over supply opening in base Optional Pre-heater Outside air rainhood 2 in. pre-filters outside air Outside air intake hood (outside units only) ERV wheel Supply air blower 2 in. pre-filters outside air Hinged and latched access door (both sides) Side View Down Discharge - Stand-lone Optional ERV roof curb Supply duct for outside air (field provided) Fig. 45 62M irflow in Stand-lone pplications 44
Step 3 Rigging and Handling To transfer the unit from the shipping platform to the storage or installation site, refer to the rigging label on the unit and these instructions. ll panels must be in place when rigging. is not designed for handling by fork truck. Damage to unit may result. Refer to Table 1 for ERV unit weights. Check lifting devices for capacity constraints. Hook rigging shackles through the holes or lifting eyes in the ERV unit. NOTE: Some 62M units have lifting eyes, some 62M units have holes in the ERV base rail. See Fig. 46. Connect lifting straps and spreader bars. See Fig. 46. Spreader bars must be positioned to prevent cables from rubbing against the ERV unit. Carefully lift the ERV unit and set on ERV roof curb. Do not drop the ERV unit onto the roof curb, as damage may occur. void twisting or uneven lifting of the unit. Never lift the unit by the hoods or any means other than the provided lifting holes or eyes. MOUNTING THE ERV UNIT INDOORS The ERV unit can be mounted indoors. Follow all local and other applicable building codes. ll panels must be secured in place prior to lifting the ERV unit in to place. Follow all local and other applicable codes when lifting, locating and mounting the ERV unit. Damage to unit may result. Locate the ERV Prior to locating the indoor ERV unit consider the intake and exhaust duct accessibility to outside walls or roof vents. When locating the ERV unit consider required service clearances. See Table 1 for unit weights to determine if building structure reinforcements are required. Determine a Method for Mounting The method for mounting and securing the ERV unit to the building structure must be field designed and installed. Mounting methods will vary depending upon specific jobsite conditions. NOTE: Hardware and pieces to secure ERV unit to the building structure must not interfere with the service clearances or duct requirements for the unit. Lift the ERV in Place Secure the ERV unit to the building structure following all applicable local building codes. Do not use the ERV duct system to support the ERV unit in any way. Follow all local and applicable building codes and manufacture and install the ductwork to the ERV unit per the duct opening connections. Equipment damage or personal injury may result. Spreader Bars RIGGING FOR ERV INSTLLTION RIGGING HOLES ERV BSE RIL Fig. 46 Rigging Details RIGGING LIFTING EYES 45
Table 1 Physical Data UNIT 62M 040 075 120 170 225 285 NOMINL CPCITY (cfm) 400 750 1200 1700 2250 2850 CPCITY RNGE (cfm) 100-550 500-1000 1000-1400 1400-2000 2000-2500 2500-3200 MXIMUM SHIPPING WEIGHT (lb) Single-Wall Models 255 440 462 850 900 1000 Double-Wall Models 367 635 657 1135 1185 1285 MXIMUM OPERTING WEIGHT (lb) Single-Wall Models 235 400 422 790 840 940 Double-Wall Models 347 595 617 1075 1125 1225 62MB,MC INDOOR UNIT DIMENSIONS (in.) Length* 29.75 43.25 43.25 62.63 62.63 62.63 Width 29.88 39.13 39.13 58.38 58.38 58.38 Height 29.75 37.88 37.88 48.88 48.88 48.88 62MD,ME OUTDOOR UNIT DIMENSIONS (in.) Length* 48.43 60.75 60.75 87.13 87.13 87.13 Width 31.24 50.13 55.13 69.38 69.38 69.38 Height 29.72 37.88 37.88 48.88 48.88 48.88 ROTRY ENERGY EXCHNGER Type Enthalpy Lightweight Polymer with Silica Gel Desiccant Coating Size (Diam. x Depth) (in.) 22.5 x 2 29.0 x 2 29.0 x 3 40.0 x 1.5 40.0 x 1.5 40.0 x 3 Nominal Drive Motor Hp N/ N/ N/ 1 / 6 1 / 6 1 / 6 SUPPLY/EXHUST IR FN Qty Type 2.Forward Curved Centrifugal Drive Type Direct djustable Belt Drive Fan Isolation Neoprene Pads Wheel Dimensions (Diam. x Width) 5.5 x 5.5 9 x 7 9 x 7 12 x 12 12 x 12 12 x 12 Nominal Motor Hp 1 / 4 1 / 2 1 1 2 2 FILTERS (optional) Type 2-in. Pleated 30% Efficiency Exhaust ir...qty...size (L x W x D) (in.) 1.12 x 20 x 2 1.18 x 25 x 2 1.18 x 25 x 2 2.20 x 25 x 2 2.20 x 25 x 2 2.20 x 25 x 2 Outside ir...qty...size (L x W x D) (in.) 1.12 x 20 x 2 1.18 x 25 x 2 1.18 x 25 x 2 2.20 x 25 x 2 2.20 x 25 x 2 2.20 x 25 x 2 UNIT 62M 330 430 550 640 750 950 NOMINL CPCITY (cfm) 3300 4300 5500 6400 7500 9500 CPCITY RNGE (cfm) 3000-3600 3600-5000 5000-6000 6000-6800 6500-8500 8500-10,500 MXIMUM SHIPPING WEIGHT (lb) Single-Wall Models 1300 1350 1440 1590 2650 2750 Double-Wall Models 1710 1760 1850 2000 3270 3370 MXIMUM OPERTING WEIGHT (lb) Single-Wall Models 1220 1270 1360 1510 2550 2650 Double-Wall Models 1630 1680 1770 1920 3170 3270 62MB,MC INDOOR UNIT DIMENSIONS (in.) Length 73.13 73.13 73.13 73.13 108.3 108.3 Width 67.89 67.89 67.89 67.89 97.87 97.87 Height 65.21 65.21 65.21 65.21 77.4 77.4 62MD,ME OUTDOOR UNIT DIMENSIONS (in.) Length 100.88 100.88 100.88 100.88 143.45 143.45 Width 87.89 87.89 87.89 87.89 121.87 121.87 Height 65.21 65.21 65.21 65.21 77.4 77.4 ROTRY ENERGY EXCHNGER Type Enthalpy Lightweight Polymer with Silica Gel Desiccant Coating Size (Diam. x Depth) (in.) 56.2 x 1.5 56.2 x 1.5 56.2 x 3 56.2 x 3 68.0 x 3 68.0 x 3 Nominal Drive Motor Hp 1 / 2 1 / 2 1 / 2 1 / 2 1 / 4 ** 1 / 4 ** SUPPLY/EXHUST IR FN Qty Type 2...Forward Curved Centrifugal Drive Type djustable Belt Drive Fan Isolation Neoprene Pads Wheel Dimensions (Diam. x Width) 15 x 15 15 x 15 15 x 15 15 x 15 18 x 18 18 x 18 Nominal Motor Hp 2 3 5 7 1 / 2 7 1 / 2 10 FILTERS (optional) Type 2-in. Pleated 30% Efficiency Exhaust ir...qty...size (L x W x D) (in.) 6.16 x 20 x 2 6.16 x 20 x 2 6.16 x 20 x 2 6.16 x 20 x 2 6.20 x 24 x 2 6.20 x 24 x 2 Outside ir...qty...size (L x W x D) (in.) 6.16 x 20 x 2 6.16 x 20 x 2 6.16 x 20 x 2 6.16 x 20 x 2 6.20 x 24 x 2 6.20 x 24 x 2 LEGEND N/ Not pplicable *dd 10 in. to 62M040 units equipped with a preheater. Dimensions include outdoor air hoods. **575-v motors are 1 / 3 hp. 46
Step 4 Installing ERV Transitions When coupling ERV units with Carrier rooftop units an ERV transition is required to link the ERV unit and the Carrier rooftop unit together. ERV UNIT COUPLED WITH 3 to 12 1 / 2 TON HVC UNIT Complete the following steps to install a transition to a3to12 1 / 2 ton rooftop unit. 1. Remove the HVC unit filter door and set aside for later use. 2. Remove the panel shipped on the HVC unit covering the return air chamber. This panel can be discarded. 3. The 62M ERV transition for 3 to 12 1 / 2 ton rooftop units includes a replacement panel to cover the return opening. Install the replacement panel, with hood scoop attached, onto the HVC unit, over the return air chamber. Screw in place. The return/exhaust scoop will cover part of the return air opening in the HVC unit. NOTE: The standard transition does not seal tight around the return air opening on the HVC unit. This allows for some air to flow back to the HVC unit and some to be drawn back through the ERV unit. 4. Slide the transition between the ERV unit and the HVC unit. Refer to Fig. 17-44 to orient the transition. Line up the transition so that it covers the openings in the HVC unit and the ERV unit. The divider in the transition must separate the supply and return openings in the ERV unit. Screw the mating flanges of the transition to the ERV unit through pre-punched holes. Caulk the seams watertight. Screw the mating flanges on the other side of the transition to the new return air cover panel on the HVC unit. Caulk seams watertight. 5. On most models the filter access door shipped with the HVC unit will be reinstalled above the transition. 6. The transition includes a balancing damper to allow for the desired separation of the return/exhaust air between the ERV and HVC units. This damper has a manual adjustment. During balancing, this damper will be adjusted to achieve desired exhaust cfm. The balancing damper can be accessed through a separate door in the transition or through the HVC unit s filter access door. See Fig. 17-44. Step 5 Make Electrical Connections Prior to performing service or maintenance operations on the ERV unit, turn off and disconnect all power switches to the unit. Be aware that there may be more than one disconnect switch. Electrical shock could cause serious personal injury or death. IMPORTNT: Only trained, qualified installers and service technicians should install, wire, start-up and service equipment. POWER SUPPLY The electrical characteristics of the available power supply must agree with the unit nameplate rating. Supply voltage must be within the limits shown. See Tables 2 and 3 for electrical and configuration data. ELECTRICL CONNECTIONS The ERV unit must have its own electrical disconnect box. If the disconnect option has not been ordered from the factory, it must be field supplied and installed per local codes. See Tables 2 and 3. If the ERV unit has an electric pre-heater factory installed, it will be wired through the ERV unit disconnect. NOTE: Most ERV units have electrical interlock safety switches on the access doors, which will not allow the ERV unit to operate if either of the access doors are opened. Low Voltage Wiring Wire low voltage per diagrams. For coupled applications, there will be a brown and black wire in the exhaust chamber, which must be tied into the HVC unit s indoor fan so that when the indoor fan is activated, the ERV unit will be activated. 48/50TJ, HJ 3 to 12 1 / 2 Ton Rooftop s with Economizers The brown and black wires can be plugged into the economizer jumper plug on the HVC unit s economizer harness. Insert the brown wire from the ERV unit into terminal 4 in the jumper plug and insert the black wire from the ERV unit into terminal 3 in the jumper plug. See Fig. 47. If the 3 to 12 1 / 2 ton rooftop unit has an economizer installed, the economizer will have an end switch attached to the economizer actuator. The end switch must be wired into the ERV unit as shown in Fig. 48. For ERV units coupled with units with factory-installed economizers, (48/50TM, HJ 15 to 25 ton units 48/50HG, PG 15 to 25 ton units) the ERV transitions to these rooftop units include an economizer end switch. This switch mounts to the hub of the economizer damper gear as shown in Fig. 49. Set the end switch so that the ERV unit s outside air blower is deactivated during economizer mode. For stand-alone units, the ERV unit is jumpered from terminals 6 and 8 and 7 and 9, providing for continuous operation. The ERV unit should be connected to an on-off device such as aco 2 sensor. High Voltage Wiring (Fig. 50-53) Connect high voltage wiring to the disconnect per Fig. 50, 52 and 53. Check blower rotation direction and adjust if necessary. 47