Parts and Accessories Installation Instructions

Parts and Accessories Installation Instructions 5 224 B Retrofit Kit Xenon Headlights MINI (R 5/R 53) LHD and RHD The installation time is approx. 8 hours, but this may vary depending on the condition of the car and the equipment in it. Retrofit kit No. 63 12 29 765 63 12 29 879

Contents Section Page Important information........................................................... 3 1. Preparations.................................................................. 4 2. Parts list...................................................................... 5 3. Connection overview of headlight adjustment control wiring harness.................. 7 4. Connection overview of headlight wiring harness................................... 8 5. Connection overview of light module wiring harness................................ 1 6. Connection overview of instrument cluster wiring harness........................... 11 7. Connection overview of base module wiring harness................................ 12 8. Installation and cabling diagram of headlight adjustment control wiring harness........ 13 9. Installation and cabling diagram of headlight wiring harness......................... 14 1. Installation and cabling diagram of light module wiring harness..................... 16 11. Installation and cabling diagram of instrument cluster wiring harness................ 17 12. Installation and cabling diagram of base module wiring harness..................... 18 13. To install the xenon headlights................................................. 19 14. To install the load sensors..................................................... 2 15. To install the headlight adjustment control wiring harness.......................... 21 16. To install the headlight wiring harness........................................... 24 17. To install the light module wiring harness........................................ 28 18. To install the instrument cluster wiring harness................................... 29 19. To install the base module wiring harness........................................ 31 2. Coding...................................................................... 33 21. Concluding work............................................................. 34 22. Circuit diagram of headlight adjustment control wiring harness...................... 35 23. Circuit diagram of headlight wiring harness...................................... 37 24. Circuit diagram of light module wiring harness.................................... 43 25. Circuit diagram of instrument cluster wiring harness............................... 45 26. Circuit diagram of base module wiring harness................................... 47 EN/2

Target group: These installation instructions are primarily designed for use within the MINI dealership organisation and by authorised MINI service companies. In any event the target group for these installation instructions is specialist personnel trained on MINI cars with the appropriate specialist knowledge. All work must be completed using the latest repair manuals, circuit diagrams, servicing manuals and work instructions in a rational order using the prescribed tools (special tools) and observing current health and safety regulations. Item numbers refer only to the overview drawing and to the texts next to the appropriate figure. The xenon headlight retrofit kit only applies to cars with an air conditioning system. In cars without a headlight cleaning system, it is also necessary to order the headlight cleaning system installation kit by quoting retrofit kit No. 61 61 29 748. Order and install heated spray jets if requested by the customer. Subject to technical modifications. Installation information Ensure that the cables/lines are not kinked or damaged as you install them in the car. If the specified PIN numbers are occupied, bridges, double crimps or twin-lead terminals must be used. Special tools required Special tools M6 tapping tool M8 tapping tool MoDIC Torque wrench - Do not archive the hard copy of these installation instructions since daily updates are made by ASAP. EN/3

1. Preparations TIS instruction No. Disconnect the battery 12... Remove the oddments box on both sides 51 16 392 Remove the door sill strips left and right 51 47 Remove the front wheel arch trim on both sides Remove the headlights on both sides 63 12 8 Remove the bonnet trim Remove the right indicator light 63 13 2 Remove the right guide rail Release the fuse holder Remove the instrument panel cover 51 45 51 Remove the cover behind the hydraulic unit Raise the rear seat bench Remove the instrument cluster Remove the radio Remove the spare wheel cover Remove the left-hand shock absorber (install the load sensor as described in the TIS) R53 cars only Remove the exhaust system EN/4

2. Parts list ) * +, - Legend A B C D E LWR (headlight adjustment control) wiring harness Headlight wiring harness Light module wiring harness Instrument cluster wiring harness Base module wiring harness EN/5

2. Parts list F G H I J K L M N O P Q R 5 273 B Legend F G H I J K L M N O P Q R Xenon headlight, right Xenon headlight, left Load sensor, front Load sensor, rear Cable ties (4x) Manual headlight adjustment control cover Fillister head screw (4x) Hexagonal screw M6 x 16 (3x) Nut M6 (2x) Flat head screw M8 x 21 (2x) Mini connector (3x) Cable tie Headlight adjustment control module EN/6

3. Connection overview of headlight adjustment control wiring harness )& )% )$ )# )" )' ) ) ) )! ) ) ) # %" * Item Description Signals Cable colour Connection location in the car Abbreviation/ Slot A LWR (headlight adjustment control) wiring harness A1 VI 26-pin socket casing To headlight adjustment control module X18114 A2 Cable open Terminal 54 BL/RT To main cable loom with miniature connector P X254, PIN 35 A3 Blade terminal contact K-BUS WS/RT/GE To joint connector right X1116 A4 Blade terminal contact DFAHR GE/GN To connector right X1186 A5 Cable eyelet Terminal 31 BR To earth post X151 A6 Socket contact GR/BR To front load sensor X1832, PIN 5 A7 Socket contact GR/WS To front load sensor X1832, PIN 1 A8 Socket contact GR/GN To front load sensor X1832, PIN 4 A9 Plug contact GR/GE To plug connector left X15S, PIN 6 A1 Socket contact SW/WS To rear load sensor X13251, PIN 1 A11 Socket contact SW/GR To rear load sensor X13251, PIN 5 A12 Socket contact SW/GN To rear load sensor X13251, PIN 4 EN/7

4. Connection overview of headlight wiring harness B5 B2 B3 B4 B6 B17 B16 B18 B15 B19 B14 B2 B8 B21 B22 B23 B1 B24 B7 B B25 B26 B9 B13 B1 B11 B12 5 275 B Item Description Signals Cable colour Connection location in the car Abbreviation/ Slot B Headlight wiring harness B1 SW 3-pin socket casing To left headlight X13 B2 SW 3-pin socket casing To right headlight X135 B3 SW 2-pin socket casing To heated spray jet left X15 B4 SW 2-pin socket casing To heated spray jet right X16 B5 SW 2-pin socket casing To additional indicator light front right X39 B6 SW 2-pin socket casing To washing water pump front right X17 B7 Cable eyelet Terminal 31 BR To earth post connection on right side skirt X151 B8 Socket contact GR/WS Tie back B9 Socket contact SW/BR To washing water pump relay left X1594, PIN 6 B1 Socket contact SW/BL To washing water pump relay left X1594, PIN 1 B11 Plug contact GR/WS Tie back B12 Socket contact GN/WS To GN 12-pin socket casing of fuse holder X126, PIN 9 B13 Socket contact GN/GE To WS 12-pin socket casing of fuse holder B14 Socket contact GE/RT To VI 26-pin socket casing of LWR (headlight adjustment control) module B15 Socket contact GE/BR To VI 26-pin socket casing of LWR (headlight adjustment control) module B16 Socket contact BL/RT To VI 26-pin socket casing of LWR (headlight adjustment control) module B17 Socket contact BL/BR To VI 26-pin socket casing of LWR (headlight adjustment control) module B18 Socket contact GE/SW To VI 26-pin socket casing of LWR (headlight adjustment control) module B19 Socket contact GE/BR To VI 26-pin socket casing of LWR (headlight adjustment control) module B2 Socket contact BL/SW To VI 26-pin socket casing of LWR (headlight adjustment control) module X124, PIN 1 X18114, PIN 2 X18114, PIN 1 X18114, PIN 4 X18114, PIN 3 X18114, PIN 1 X18114, PIN 11 X18114, PIN 9 EN/8

4. Connection overview of headlight wiring harness Item Description Signals Cable colour Connection location in the car B21 Socket contact BL/BR To VI 26-pin socket casing of LWR (headlight adjustment control) module B22 Round contact WS/BL To GN 2-pin socket casing of base module B23 Round contact GE/BL To GN 2-pin socket casing of base module B24 Round contact WS/GN To GN 2-pin socket casing of base module B25 Round contact GE/GN To GN 2-pin socket casing of base module B26 Socket contact BL/GE To WS 54-pin socket casing of base module Abbreviation/ Slot X18114, PIN 8 X332, PIN 13 X332, PIN 19 X332, PIN 9 X332, PIN 15 X254, PIN 13 EN/9

5. Connection overview of light module wiring harness +! + + + # %$ * Item Description Signals Cable colour Connection location in the car Abbreviation/ Slot C Light module wiring harness C1 Socket contact GR/GE To plug connector left X15B, PIN 6 C2 Socket contact GR/GE To BL 54-pin plug base module X255, PIN 34 C3 Socket contact GR/GE To BL 54-pin plug base module X255, PIN 52 EN/1

6. Connection overview of instrument cluster wiring harness,!,$,,#,,," # %% * Item Description Signals Cable colour Connection location in the car Abbreviation/ Slot D Instrument cluster wiring harness D1 Socket contact BR/SW To SW 18-pin plug left X23B, PIN 11 D2 Socket contact GN/GR To SW 18-pin plug left X23B, PIN 12 D3 Socket contact GN/BL To SW 18-pin plug left X23B, PIN 13 D4 Socket contact BR/SW To WS 18-pin plug behind instrument cluster X1527B, PIN 3 D5 Socket contact GN/GR To WS 18-pin plug behind instrument cluster D6 Socket contact GN/BL To WS 18-pin plug behind instrument cluster X1527B, PIN 5 X1527B, PIN 6 EN/11

7. Connection overview of base module wiring harness -" -% -! -$ - -# - - # %& * Item Description Signals Cable colour Connection location in the car Abbreviation/ Slot E Base module wiring harness E1 Socket contact BR/SW To base module X254, PIN 1 E2 Socket contact BR/SW To base module X254, PIN 2 E3 Socket contact GN/BL To base module X254, PIN 3 E4 Socket contact GN/GR To base module X254, PIN 37 E5 Plug contact BR/SW To SW 18-pin plug left X23S, PIN 11 E6 Plug contact GN/GR To SW 18-pin plug left X23S, PIN 12 E7 Plug contact GN/BL To SW 18-pin plug left X23S, PIN 13 EN/12

8. Installation and cabling diagram of headlight adjustment control wiring harness ) ) )! )# )" ) )$ )% )& )' ) ) 5 279 B All the wiring harnesses are to be laid along the main cable loom as shown in the figure and secured with cable ties. Legend A1 To LWR (headlight adjustment control) module X18114 A2 To main cable loom with miniature connector A3 To joint connector right X1116 A4 To joint connector right X1186 A5 To earth post connection right X151 A6 To load sensor front X1832, PIN 5 A7 To load sensor front X1832, PIN 1 A8 To load sensor front X1832, PIN 4 A9 To plug connector left X15S, PIN 6 A1 To rear load sensor X13251, PIN 1 A11 To rear load sensor X13251, PIN 5 A12 To rear load sensor X13251, PIN 4 Tie back any excess lengths. EN/13

9. Installation and cabling diagram of headlight wiring harness B6 B5 B2 B4 B14-21 B7 B26 B22-25 B3 B8 B1 B9 B13 B1 B12 B11 5 28 B All the wiring harnesses are to be laid along the main cable loom as shown in the figure and secured with cable ties. Legend B1 To xenon headlight left X13 B2 To xenon headlight right X135 B3 To heated spray jet left X15 B4 To heated spray jet right X16 B5 To additional indicator light front right X39 B6 To washing water pump front right X17 B7 To earth post connection on side skirt right X151 B8 To steering angle sensor X1829, PIN 6 (cable is tied back) B9 To washing water pump relay left X1594, PIN 6 B1 To washing water pump relay left X1594, PIN 1 B11 To plug connector left X15S, PIN 23 (cable is tied back) B12 To fuse holder X126, PIN 9 B13 To fuse holder X124, PIN 1 B14 To LWR (headlight adjustment control) module X18114, PIN 2 B15 To LWR (headlight adjustment control) module X18114, PIN 1 B16 To LWR (headlight adjustment control) module X18114, PIN 4 B17 To LWR (headlight adjustment control) module X18114, PIN 3 B18 To LWR (headlight adjustment control) module X18114, PIN 1 B19 To LWR (headlight adjustment control) module X18114, PIN 11 B2 To LWR (headlight adjustment control) module X18114, PIN 9 B21 To LWR (headlight adjustment control) module X18114, PIN 8 B22 To base module X332, PIN 13 EN/14

9. Installation and cabling diagram of headlight wiring harness Legend B23 To base module X332, PIN 19 B24 To base module X332, PIN 9 B25 To base module X332, PIN 15 B26 To base module X254, PIN 13 Tie back any excess lengths. EN/15

1. Installation and cabling diagram of light module wiring harness +! + + 5 281 B All the wiring harnesses are to be laid along the main cable loom as shown in the figure and secured with cable ties. Legend C1 To plug connector left X15B, PIN 6 C2 To base module X255, PIN 34 C3 To base module X255, PIN 52 Tie back any excess lengths. EN/16

11. Installation and cabling diagram of instrument cluster wiring harness,$,#,",!,, 5 282 B All the wiring harnesses are to be laid along the main cable loom as shown in the figure and secured with cable ties. Legend D1 To plug left X23B, PIN 11 D2 To plug left X23B, PIN 12 D3 To plug left X23B, PIN 13 D4 To plug behind instrument cluster X1527B, PIN 3 D5 To plug behind instrument cluster X1527B, PIN 5 D6 To plug behind instrument cluster X1527B, PIN 6 Tie back any excess lengths. EN/17

12. Installation and cabling diagram of the xenon base module wiring harness - - -! -" -# -$ -% 5 283 B All the wiring harnesses are to be laid along the main cable loom as shown in the figure and secured with cable ties. Legend E1 To base module X254, PIN 1 E2 To base module X254, PIN 2 E3 To base module X254, PIN 3 E4 To base module X254, PIN 37 E5 To plug left X23S, PIN 11 E6 To plug left X23S, PIN 12 E7 To plug left X23S, PIN 13 Tie back any excess lengths. EN/18

13. To install the xenon headlights F G L L 5 284 B Install xenon headlights F/G. Attach the xenon headlight control unit left/right using 2 fillister head self-tapping screws L each. EN/19

14. To install the load sensors Wheel arch front left Unscrew the bolt (1) at the front which secures the inner ball joint to the front axle transverse control arm. Ensure that the drive shaft joint cup (2) is not damaged. Install the load sensor holder H, tighten bolt (1) to 165 Nm. # &# * H M If there is no thread in the front axle bracket, use the M6 tapping tool to cut a thread in the existing hole (1). Use hexagonal screw M6 x 16 Mto screw the holder and load sensor H tightly onto the front axle bracket. 1 1 # && * Rear left transverse control arm If there is no thread in the transverse control arm, use the M8 tapping tool to cut a thread in the existing holes (1). # &' * O 1 Rear left axle bracket If there is no thread in the axle bracket, use the M6 tapping tool to cut a thread in the existing holes (1). Use 2 pan head screws M8 x 21 O to screw the holder and load sensor I tightly onto the top transverse control arm. M Use 2 hexagonal screws M6 x 16 Mto screw the holder and load sensor tightly onto the axle bracket. I # ' * The load sensor must be fitted above the brake line. EN/2

15. To install the headlight adjustment control wiring harness Route A1 A12 underneath the rear seat bench to the rear load sensor through the rubber grommet (1). Carefully cut open the rubber grommet to do this. Seal the rubber grommet (1). 1 A1-A12 # '! * Connect A1 A12 to the supplied SW 6-pin casing. A1 SW/WS PIN 1 A11 SW/GR PIN 5 A12 SW/GN PIN 4 Seal unused slots with the supplied blind stoppers and route them towards the front like cables. # '" * Route A6 A8 through the rubber grommet (1) below the fuse box. Seal the rubber grommet (1). A6-A8 # " * Q Route A6 A8 to the load sensor and secure it to the existing cable using a cable tie J. If (1) is not fitted, fit a cable tie Q and secure it to the wiring harness. 1 A6-A8 J # "! * EN/21

15. To install the headlight adjustment control wiring harness Connect A6 A8 to the supplied SW 6-pin casing. A6 GR/BR PIN 5 A7 GR/WS PIN 1 A8 GR/GN PIN 4 Use the supplied blind stoppers to seal the free slots. # '% * )' Footwell front left. Route A9 to the SW 42-pin plug X15S and connect it. A9 GR/GE X15S, PIN 6 Route A1 A5 behind the radio to the right-hand side # '& * A1 1 Footwell front right. Use 2 M6 nuts N to screw the LWR (headlight adjustment control) module R tightly on to the existing stud bolt (1). Route A1 to the LWR (headlight adjustment control) module R. R N #! * If the installation site is already occupied, secure with a cable tie. Footwell front right. Route A2 to the main cable loom. Carefully cut open the main cable loom and locate the BL/RT cable. Use the supplied miniature connector P to connect A2 BL/RT to the BL/RT power supply cable of the base module X254, PIN 35. 2 ) #! * EN/22

15. To install the headlight adjustment control wiring harness Right side skirt. Connect A3 WS/RT/GE to the joint connector X1116. If occupied, attach A3 to X1116 using miniature connector P. )! :$ #! * :# Right side skirt. Screw A5 tightly onto earth post connection X151. )# #! * )" :&$ Right side skirt. Connect A4 GE/GN to the joint connector X1186. If occupied, attach A4 to X1186 using miniature connector P. #!" * EN/23

16. To install the headlight wiring harness *" *! * * #!$ * Remove the old headlight wiring harness as far as the rubber grommet behind the ABS hydraulic unit (the old wiring harness will later be shortened and removed). Route the headlight wiring harness B along the cable guide for the old headlight wiring harness. B1 to X13 B2 to X135 B3 to X15 B4 to X16 If you are not installing heated spray jets, insulate B3 and B4 and tie them back to a suitable point. Only for RHD cars. B7ÐB26 Rubber grommet (1) near the brake booster. Carefully cut open the rubber grommet (1) and thread B7 B26 through the rubber grommet (1) into the interior. Seal the rubber grommet (1). * # " * * B7ÐB26 Only for LHD cars. Rubber grommet (1) behind the ABS hydraulic unit. Carefully cut open the rubber grommet (1) and thread B7 B26 through the rubber grommet (1) into the interior. Seal the rubber grommet (1). #!% * EN/24

16. To install the headlight wiring harness B8ÐB13 Route B8 B13 above the instrument holder to the left. Tie back B8 and B11 (not required). #!& * Route B9 and B1 to the washing water pump relay X1594. Disconnect the old cables in question, tie them back and replace them with new ones. B9 SW/BR PIN 6 B1 SW/BL PIN 1 :#'" * *' #!' * Route B12 to the fuse holder and connect it to the GN plug X126. B12 GN/WS PIN 9 * : $ #! * Route B13 to the fuse holder and connect it to the WS plug X124. B13 GN/GE PIN 1 *! : " #! * EN/25

16. To install the xenon headlight wiring harness :&" Route B14 B21 to the LWR (headlight adjustment control) module. Connect B14 B21 to the VI plug X18114. B14 GE/RT PIN 2 B15 GE/BR PIN 1 B16 BL/RT PIN 4 B17 BL/BR PIN 3 B18 GE/SW PIN 1 B19 GE/BR PIN 11 #! * B2 BL/SW PIN 9 B21 BL/BR PIN 8 Route B22 B25 to the base module X332. Disconnect the old cables in question, tie them back and replace them with new ones. B22 WS/BL PIN 13 B23 GE/BL PIN 19 B24 WS/GN PIN 9 B25 GE/GN PIN 15 :!! #!! * Route B26 to the base module WS plug X254. Disconnect the old cables in question, tie them back and replace them with new ones. B26 BL/GE PIN 13 : #" #!" * EN/26

16. To install the xenon headlight wiring harness Base module WS plug X254. Disconnect and tie back the following cables: BL/RT PIN 1 GE/BR PIN 2 BL/SW PIN 3 BL/BR PIN 19 GE/RT PIN 2 BL/BR PIN 21 : #" #!# * :# GE/SW PIN 37 GE/BR PIN 38 Route B7 to the earth post connection X151 and screw it on tightly. *% #!$ * a 1 Cut off the old wiring harness in front of the rubber grommet (1) and insulate it so it is water-tight. Dimension a = 1 mm Tie back the wiring harness to a suitable point. #!% * EN/27

17. To install the light module wiring harness + Footwell front left. Connect C1 GR/GE to X15B, PIN 6. :#* #!& * Route C2 and C3 above the instrument holder to the right to the base module. C2-C3 #!' * Base module right. Connect C2 and C3 to plug X255. C2 GR/GE PIN 34 C3 GR/GE PIN 52 If the plug is occupied, disconnect it and tie it back. : ## #! * EN/28

18. To install the instrument cluster wiring harness :!* Footwell front left. Connect D1 D3 to the SW 18-pin plug X23B. D1 BR/SW PIN 11 D2 GN/GR PIN 12 D3 GN/BL PIN 13 See next figure. #! * If a 1-pin plug is fitted, replace this with the supplied SW 18-pin plug. #! * :!* #!! * SW 18-pin socket casing X23B (if WS 1-pin fitted). Reconnect the following cables (if present): BR PIN 1 SW/BL/GE PIN 2 BL/BR PIN 3 BR/GE PIN 4 BR/SW PIN 5 VI/BL PIN 6 RT/GN PIN 7 VI/GR PIN 8 BR/SW PIN 9 BR/VI PIN 1 D1 PIN 11 D2 PIN 12 D3 PIN 13 EN/29

18. To install the instrument cluster wiring harness :!5 #! " * SW 18-pin plug casing X23S (if WS 1-pin fitted). Reconnect the following cables (if present): BR PIN 1 SW/BL/GE PIN 2 BL/BR PIN 3 BR/GE PIN 4 BR/SW PIN 5 VI/BL PIN 6 RT/GN PIN 7 VI/GR PIN 8 BR/SW PIN 9 BR/VI PIN 1 Route D4 D6 above the instrument holder to the instrument cluster. Route to the monitor in cars with an on-board monitor. :# %* D4ÐD6 #! # * Connect D4 D6 to the WS 18-pin plug X1527B. Disconnect the old cables in question, tie them back and replace them with new ones. D4 BR/SW PIN 3 D5 GN/GR PIN 5 D6 GN/BL PIN 6 #! $ * EN/3

19. To install the base module wiring harness Connect E1 E4 to the WS plug of the base module X254. E1 BR/SW PIN 1 E2 BR/SW PIN 2 E3 GN/BL PIN 3 E4 GN/GR PIN 37 : #" #! % * E5ÐE7 Route E5 E7 above the instrument holder to the SW plug casing X23S. #! & * Footwell front left. Connect E5 E7 to the SW plug X23S. E5 BR/SW PIN 11 E6 GN/GR PIN 12 :!5 E7 GN/BL PIN 13 #! ' * Tie back the manual headlight adjustment control plug (1). #!! * EN/31

19. To install the base module wiring harness Replace the manual headlight adjustment control switch in the oddments box with the supplied cover K. K #!! * EN/32

2. Coding Connect the battery. This system requires coding. - To ensure that the retrofit system - is fully functional and - prevents malfunctions and errors when combined with other electrical systems in the car, this retrofit system and, possibly, other components must be coded and saved in the central code of the IKE. This coding process is automatic using the current coding program in the Retrofit path. The procedure is user-guided, follow the text instructions for completing each individual step. Procedure - DIS/MoDiC: Connect to the vehicle - Ignition: ON - Select: Coding ZCS/FA - Series: R5 - Path: 2 Retrofit - System: Xenon headlights EN/33

21. Concluding work Connect all plugs and plug connectors. Re-assemble the car. EN/34

22. Circuit diagram of headlight adjustment control wiring harness 6 TBC X15S X1186 X1116 DFAHR K-BUS,5 GRGE,35 GEGN,35 WSRTGE TBC DFAHR K-BUS 13 24 14 X18114 16 5 18 HSSV HSGV HSPV,5 GRGN,5 GRWS,5 GRBR HSSV HSGV HSPV 4 1 5 X1832 G2 2 7 22 25 26 21 HSSH HSGH HSPH 31 31 KL54 X18114,5 SWGN,5 SWWS,5 SWBR,5 BR,5 BR,35 BLRT HSSH HSGH HSPH 4 1 5 X13251 X11359,5 BR 31 X151 5 335 B EN/35

22. Circuit diagram of headlight adjustment control wiring harness Legend G2 LWR (headlight adjustment control) module X15S Plug connector VO-INSTR. I X151 Earth post X1116 VB (connector) K-BUS X1186 VB (connector) DFAHR X11359 LTG (cable) open tl. 54 X13251 Load sensor HI (rear) LWR (headlight adjustment control) X1832 Load sensor VO (front) LWR (headlight adjustment control) X18114 VI 26-pin socket casing LWR (headlight adjustment control) Cable colours RT SW GN BR GE WS VI GR BL OR red black green brown yellow white violet grey blue orange EN/36

23. Circuit diagram of headlight wiring harness G2 G1 3 4 1 2 X18114 9 8 1 11 15 9 13 19 Q21L Q22L Q11L Q12L Q21R Q22R Q11R Q12R 56a 56b 56b 56a X332,5 BLBR,5 BLRT,5 GEBR,5 GERT,5 BLSW,5 BLBR,5 GESW,5 GEBR 2,5 GEGN 1,5 WSGN 1,5 WSBL 2,5 GEBL Q21L Q22L Q11L Q12L 4 2 3 5 Q21R Q22R Q11R Q12R 56a 56b 56b 56a X13 4 2 3 5 X135 9 6 X13 6 9 X135 M M 8 8 31L 31L 2,5 BR 2,5 BR X151 X151 5 336 B EN/37

23. Legend, circuit diagram of headlight wiring harness Legend G1 G2 X13 X135 X151 X332 X18114 Base module LWR (headlight adjustment control) module Full beam headlight, left Full beam headlight, left Earth Base module A VI 26-pin socket casing Cable colours RT SW GN BR GE WS VI GR BL OR red black green brown yellow white violet grey blue orange EN/38

23. Circuit diagram of headlight wiring harness G3 F12 2A X126 9 1 15 DIAG,5 GNWS,35 GRWS,5 GNWS,35 GRWS,5 GNWS,35 GRWS 15A DIAG 15 DIAG 1 7 1 7 X13 X135,35 GRWS D92 1 X1* X2* G1 H1 13 49VR,5 BLGE 1 2,35 BR 31 X254 X39 X39 X151 5 337 B EN/39

23. Legend, circuit diagram of headlight wiring harness Legend G1 Base module G3 Fuse holder X1* No longer required H1 Additional indicator light, front right X15S Plug VO-INSTR. I X13 Full beam headlight, left X135 Full beam headlight, left X151 Earth X254 WS 54-pin socket casing X39 Additional indicator light, front right X126 GN 12-pin socket casing X2* No longer required Cable colours RT SW GN BR GE WS VI GR BL OR red black green brown yellow white violet grey blue orange * Names with an asterisk refer to this circuit diagram and not to the BMW dealer organisation s circuit diagrams. EN/4

23. Circuit diagram of headlight wiring harness X1594 X1594 1 6 1,5 SWBL 1,5 SWBR 2 1 X17 M G3 X124 X15 X15 X151 X16 X16 F35 5A 1 KL15,75 GNGE,5 GNGE,5 GNGE KL15 1 1 KL15 31 2 2 31,5 BR,5 BR 31 5 338 B EN/41

23. Circuit diagram of headlight wiring harness Legend G3 X15 X16 X17 X151 X1594 X124 Fuse holder Heated spray jet, left Heated spray jet, right Washing water pump Earth Washing water pump relay WS 12-pin socket casing Cable colours RT SW GN BR GE WS VI GR BL OR red black green brown yellow white violet grey blue orange EN/42

24. Circuit diagram of light module wiring harness S G1 34 TBC 52 TBC X255,5 GRGE,5 GRGE,5 GRGE TBC 6 X15B 5 332 B EN/43

24. Circuit diagram of light module wiring harness Legend G1 X15B X255 Base module Plug connector VO-INSTR. I BL 54-pin socket casing Cable colours RT SW GN BR GE WS VI GR BL OR red black green brown yellow white violet grey blue orange EN/44

25. Circuit diagram of instrument cluster wiring harness S 3 5 6 X1527B 31E C2 FRESH,5 BRSW,5 GNGR,5 GNBL 31E C2 FRESH 11 12 13 X23B 5 334 B EN/45

25. Circuit diagram of instrument cluster wiring harness Legend X1527 X23B Plug, IHKA (integrated automatic heater/air conditioning) I Plug connector VO-INSTR. Cable colours RT SW GN BR GE WS VI GR BL OR red black green brown yellow white violet grey blue orange EN/46

26. Circuit diagram of base module wiring harness S G1 1 2 37 3 31E 31E C2 FRESH X254,5 BRSW,5 BRSW,5 GNGR,5 GNBL,5 BRSW 31E C2 FRESH 11 12 13 5 333 B EN/47

26. Circuit diagram of base module wiring harness Legend G1 X23S X254 Base module Plug connector VO-INSTR. WS 54-pin socket casing Cable colours RT SW GN BR GE WS VI GR BL OR red black green brown yellow white violet grey blue orange EN/48