Bauart gepruft Sicherheit egelma ge od o s be wac g www. tuv.com ID 000000000 GB494 UL950- EN950- EN5- IEC950- % - ~+ R
SPECIFICATION MODEL UHP-00 -. UHP-00-4. UHP-00-5 UHP-00 - UHP-00-5 UHP-00-4 UHP-00-6 UHP-00-48 OUTPUT INPUT PROTECTION FUNCTION OTHERS NOTE VOLTAGE ADJ. RANGE.~.5V.6~4.4V 4.5~5.5V.4~.6V VOLTAGE TOLERANCE Note. ±.0% ±.0% ±.0% LINE REGULATION LOAD REGULATION SETUP, RISE TIME 000ms, ms/0vac 000ms, ms/5vac at full load HOLD UP TIME (Typ.) 0ms/0VAC 0ms/5VAC VOLTAGE RANGE Note.4 90 ~ 64VAC 7 ~ 70VDC FREQUENCY RANGE 47 ~ 6Hz POWER FACTOR (Typ.) PF 0.94/0VAC PF 0.98/5VAC at full load EFFICIENCY (Typ.) 89% 90% 9% 9% AC CURRENT (Typ.).A/5VAC.A/0VAC INRUSH CURRENT (Typ.) LEAKAGE CURRENT OVERLOAD OVER VOLTAGE OVER TEMPERATURE WORKING TEMP. WORKING HUMIDITY ENVIRONMENT STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT VIBRATION SAFETY & EMC (Note.6) DC VOLTAGE RATED CURRENT.V A RATED POWER(convection) W RIPPLE & NOISE (max.) Note. 50mVp-p DC OK SIGNAL(Optional) REDUNDANT(Optional) SAFETY STANDARDS WITHSTAND VOLTAGE ISOLATION RESISTANCE EMC EMISSION EMC IMMUNITY MTBF DIMENSION Cold start A/5VAC <0.75mA / VAC 4.V A 68W 50mVp-p 0~% rated output power A/0VAC Protection type : Hiccup mode, recovers automatically after fault condition is removed.8~ 4.6V Protection type :Shut down O/P voltage,re-power on to recover Protection type :Shut down O/P voltage, recovers automatically after temperature goes down Contact rating(max.):5vdc/0ma resistive load -0 ~ +70 (Refer to Derating Curve") 0 ~ 95% RH non-condensing - ~ +85, 0 ~ 95% RH non-condensing ± 0.0%/ (0 ~ 50 ) 0 ~ 500Hz, 5G 0min./cycle, min. each along X, Y, Z axes 57K hrs min. MIL-HDBK-7F (5 ) 94*55*6mm (L*W*H) 5V A 00W 00mVp-p V 6.7A 00.4W 4.~5.8V PACKING 0.468kg;4pcs/.kg/0.49CUFT The The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets EMC directives. 5V.4A 0W 4V 8.4A 0.6W.8~5.V 94% 94% 6V 5.6A 0.6W 4.~7.8V For parallel connection protection:for parallel applications, when one PSU can not work, the another one will be automatically enabled. This can prevent the system crash, and provide the reliability of system 48V 4.A 0.6W 00mVp-p 45.6~50.4V UL950-,TUV EN950-,EN5-, CCC GB494, EAC TP TC 004, BSMI CNS46- approved, Design refer to EN6558-,--6 I/P-O/P:.75KVAC I/P-FG:KVAC O/P-FG:.5KVAC I/P-O/P, I/P-FG,O/P-FG:M Ohms/500VDC/5 / 70%RH Compliance to EN550,GB954,Class B, EN5504,EN--,-,EAC TP TC 00,BSMI CNS48 Compliance to EN-4-,,4,5,6,8,;EN-6- (EN5008-), heavy industry level,criterial A,EAC TP TC 00 4.6 ~ 5.46V 5.75 ~ 6.75V. ~ 5.6V 6.5 ~ 9.5V 6.4 ~.V 9.6 ~46.8V 5.8 ~ 6.4V 94% 94%
Block Diagram I/P EMI FILTER & RECTIFIER PFC CIRCUIT POWER SWITCH- ING RECTIFIERS & FILTER FG O.T.P. O.L.P. CONTROL DETECTION CIRCUIT O.V.P. DC OK Function Redundant Function Derating Curve 0Vac for 4.V,5V;Vac for other 0Vac for other RATED CURRENT (%) 0 RATED CURRENT (%) 0 Vac for 4.V,5V -0 0 0 0 0 50 70 (HORIZONTAL) -0 0 0 0 0 50 70 (HORIZONTAL) AMBIENT TEMPERATURE ( ) AMBIENT TEMPERATURE WITHOUT ALUMINUM PLATE( ) RATED CURRENT (%) 0-0 0 0 0 0 50 70 90 (HORIZONTAL) Tcase ( )
STATIC CHARACTERISTIC 90 LOAD (%) 70 50 90 0 0 00 0 64 INPUT VOLTAGE (V) Hz Function Manual.DC_OK Signal DC_OK is a collector shorted signal. It is used by an optocoupler in the power supply which indicates the output status of the power supply as exhibited below. DC OK K C E Optocoupler C-E Pin Conduction Optocoupler C-E Pin Open Optocoupler Rating(max.) PSU turns on DC ok PSU turns off DC fail 5Vdc/0mA resistive load GND PSU COM.Redundant function () UHP-00R is built-in redundant function and can be connected units in parallel. () When in parallel operation the maximum load should not be greater than the rated power of any PSU. PSU LOAD PSU
Mechanical Specification CASE NO.:49B Unit:mm 94 88 7.6 6.5 TB TB TB 4 8.8 8.5 8 4 55 SVR 4-ψ. L=6 97 tc 6 tc : Max. Case Temperature AC Input Terminal(TB) pin NO. Assignment Terminal Max mounting torque Pin No. Assignment AC/L AC/N (DEGSON) DG8C-B-0P 5Kgf-cm DC Output Terminal(TB,TB) pin NO. Assignment Pin No. Assignment Terminal Max mounting torque, (MW),4 TB-HTP-00-A 8Kgf-cm DC OK Connector(CN0):JST BB-PH-K-S or requivalent Mating Housing Terminal Pin No. Assignment DC COM DC OK JST PHR- or requivalent JST SPH-00T-P0.5S or requivalent
Installation.Operate with additional aluminum plate In order to meet the Derating Curve and the Static Characteristics, must be installed onto an aluminum plate(or the cabinet of the same size) on the bottom.the size of the suggested aluminum plate is shown as below. And for optimizing thermal performance, the aluminum plate must have an even and smooth surface (or coated with thermal grease), and must be firmly mounted at the center of the aluminum plate. unit:mm 00 M*4 00