Instructions for Models: SB-8 SB-8-E What You Need To Know: Tools: Required: *Adjustable Wrench *Groove Joint Pliers *Philips Screwdriver Important Notes: Be sure to read instructions thoroughly before beginning installation. Do not overtighten any connections or damage may occur. This faucet has an operating range of 0-80 psi. Safety Tips: Cover your drain to prevent loss of parts. Be sure to wear eye protection while cutting pipe. Insert flexible hoses into the faucet base as shown, tighten the handle with the clamp spring, and then press the button of the spout in order to set flexible hoses and the faucet. Maintenance: Your new Lavatory Faucet is designed for years of trouble-free performance. Keep it looking new by cleaning it periodically with a soft cloth. Avoid abrasive cleaners, steel wool, and harsh chemicals as these will dull the finish and void your warranty. *Teflon Tape Shut off water supplies.remove old faucet. Clean sink surface in preparation for new faucet. Place spout thru mounting hole in sink. Secure spout with rubber washer,metal washer and nut. Make connections to water lines.use / IPS faucet connections () or use the supplied coupling nuts () with /8 O.D. ball nose risers ().Use wrenches to tighten connections.do not overtighten. Helpful: *Supply Lines *Basin Wrench *Pipe Wrench Need Help? For additional assistance or service call: *Hacksaw *Tubing Cutter *Utility Knife Slide Hot and Cold end valves thru sink mounting holes. NOTE:Hot side end valve is labeled. Secure end valves with washers and nuts. Hand tighten nuts onto shank. Lock nuts into pisition by tightening screws. Remove flange () and rubber washer () from POP-UP drain assembly. SPEAKMAN Company 00 Anchor Mill Road New Castle, DE 90 PHONE: 800--0 EMAIL: customerservice@speakman.com WEB: www.speakman.com *Eye Protection 9-SB-8-R
Place the rubber washer () to underside of the flange (). Insert the threaded end of the drain body up through the drain hole and attach flange to the body with the pivot hole () pointing to the rear of the sink. 9 Place one end of spring clip () on the end of pivot rod (). Insert rod through hole in lift rod strap ().Secure with spring clip (). RPG0-00 (-BN) RPG0-099 RPG0-090 RPG-00 RPG0-09 (.GPM) RPG-0089 RPG0-0 (.GPM) / Unscrew the nut () from the pop-up body. NOTE:Retain the seal () on the pivot rod (). Place the nut onto the pivot rod insert the rod and seal () into the pivot hole ().Install stopper () as shown ().Slide nut () on and hand tighten. (Please do not overtighten). 0 Insert lift rod () into strap () and tighten screw(). 8 Tighten lock nut () by rotating counterclockwise until the pop-up drain assembly is secure. Rubber washer should be on top of sink. IMPORTANT: After installation is completed, remove aerator. Turn on water supply and allow both hot and cold water to run for at least one minute each to remove the debris. While water is running,check for leaks. Replace aerator.. [0mm].89 [8mm].09 [mm].8 [8mm].8 [mm]. [mm].9 [mm]. [mm].8 [0mm].0 [0mm] 8.0 [0mm]
SPEAKMAN COMPANY Tiber TM Collection Combination Series SM-00-P DESCRIPTION Speakman Tiber TM Collection Combination Series unites the best products included in our Tiber TM Series. The combination begins with our anti-scald balanced pressure valve with integral stops, featuring a brass body and adjustable temperature limit stop. The wall plate and handle are designed with definitive Tiber TM Collection styling. Piston type pressure balancing/ceramic regulating cartridge assembly with built-in check valves. Meets ASME A.8. / CSA B. & ASSE 0 standards. Also provided is the S- brass shower arm with metal wall flange. The featured product in the Tiber TM Collection Combination Series is the ANYSTREAM S-0 showerhead with a outer spray adjustment ring. Five self-cleaning plunger nozzles resist scale build-up and provide spray streams for a full body coverage pattern. The center core nozzle delivers massaging jets and a combination spray is included. Waterconserving pressure compensating AUTOFLO device reduces flow to. GPM / 9. LPM maximum, to meet existing ANSI A.8. Standard. Also included in this package is the metal S- tub spout, which features an integrated diverter, matched to the style of the other combination pieces. SPECIFICATIONS SM-000-P Anti-Scald Balanced Pressure Valve: Connections: ½ female copper sweat inlets & shower outlet; ½ NPT female tub outlet Flow Rate: For use with showerheads rated at.0 GPM (. LPM) or higher S-0 Showerhead: Supply: ½ NPT female Flow Rate:. GPM / 9. LPM MAX S- Shower Arm: Supply: ½ NPT male inlet Outlet: ½ NPT male outlet S- Tub Spout with Diverter: Supply: ½ copper pipe slip fit INSTRUCTIONS See individual products for installation of the components and warranty information. ROUGH-IN 9 SM 00 P R
INSTRUCTIONS FOR MODELS SA-0 TOWEL RACK SA-0 TOWEL BAR SA-0 PAPER HOLDER SA-0 ROBE HOOK SA-0 TOWEL BAR Pencil TOOLS AND SUPPLIES Hex Key (included) Level Phillips Screwdriver Drill Phillips Drive Bit Drill Bit Ø/ The Mounting Plate () comes pre-installed in the Accessory (). Remove the Mounting Plate(s) by loosening the pre-installed set screw at bottom with the included Hex Key. Align Mounting Plate over center point marked in previous step. Mounting Plate should be vertical with Notch in the cylinder () pointing to the bottom as shown below. Mark Mounting Screw locations onto the wall surface. Remove items after marking mounting locations. IMPORTANT Do not over-tighten any connections or damage may occur. Be sure to read instructions thoroughly before beginning installation. If mounting directly to wood stud, Plastic Anchors are not required. If mounting to tile, acquire proper mounting hardware capable of supporting the accessory in use. If mounting to drywall, drill guide holes at marked locations using a Drill equipped with a Ø /" bit. Ø / SAFETY TIPS At the selected height, mark center point of mounting locations onto wall referencing the rough in diagram. Cover your drain to prevent loss of parts. For additional assistance or service please contact: SPEAKMAN Company 00 Anchor Mill Road New Castle, DE 90 800--0 customerservice@speakman.com MAINTENANCE Your new Speakman Product is designed for years of trouble-free performance. Keep it looking new by cleaning it periodically with a soft cloth. The use of harsh chemicals and abrasives on any of the Speakman custom finish products may damage the finish and void the product warranty. Please be sure to only use approved cleaners. Please contact Speakman for any clarification of acceptable cleaners. Insert Plastic Anchors into drilled holes and screw in the anchor using a Phillips Head screwdriver, or a Drill equipped with a Phillips Driver Bit until the head is flush with the wall surface. www.speakman.com WARRANTY OR 9-SA-00-0 Additional warranty information can be found at: www.speakman.com
Secure Mounting Plate with the Mounting Screws provided. Verify that the Mounting Plate is aligned vertically. ROUGH-IN DIAGRAMS SPEAKMAN " 0mm " 8mm " 8mm " 0mm 8 " 9mm " mm " 0mm " mm 8 " 0mm 0 " mm SA-0 " 8mm 8 " 0mm SA-0 " Place Accessory () over Mounting Bracket and secure the pre-installed set screw () with the included Hex Key. mm " 0mm " 8mm " mm SA-0 " 0mm in mm " 0mm 9 " mm " 0mm " mm SA-0 SA-0 DIMENSIONS SUBJECT TO CHANGE WITHOUT NOTICE.