Omega R&D Inc. INSTALL GUIDE OL-AL(MDB)-GM Available for : OL-MDB-ALL Rev. Date: March 3, 0 Doc. No.: ##887## 003 GM please visit www.caralarm.com for complete product details The brand names and logos found in this guide are property of their respective owners. Omega R&D Inc. 0 NOTICE: The manufacturer will accept no responsibility for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician. This guide has been written for properly trained technicians; a certain level of skill & knowledge is therefore assumed. Please!review the Installation Guide carefully before beginning any work.
Page of OL-AL(MDB)-GM Doc. No.: ##887## 003 install TYPE SELECTiOn FEATURES NOTE MAKE MODEL YEAR INSTALL TYPE DATA IMMOBILIZER BYPASS ARM OEM ALARM DISARM OEM ALARM DOOR LOCK DOOR UNLOCK PRIORITY UNLOCK TRUNK/HATCH RELEASE PUDDLE LIGHT CTRL DOOR STAT OUTPUT TRUNK STAT OUTPUT TACHOMETER OUTPUT BRAKE PEDAL STAT OUTPUT 3 E-BRAKE OUTPUT 3 RAP SHUTDOWN CTRL I The 0th character in the Vehicle Identification Number (VIN) indicates the manufacturing year: =00; =00; 3=003... CHEVROLET PONTIAC SATURN Cobalt 05-06 Cobalt 07-0 HHR 06 HHR 07- Malibu Classic 04-07 Malibu 07- Malibu Hybrid 08- Malibu MAXX 04-06 Malibu MAXX 07-09 G6 05-06 G6 07-09 Pursuit / G5 05-06 Pursuit / G5 07-0 Solstice 06 Solstice 07-09 Aura / Hybrid 07-0 Sky 07-09 Doorlocks and trunk release features on the module will not operate on vehicles that are not equipped with OEM keyless entry. If puddle light function is active in vehicle settings. 3 Available on AL-CA modules in DATA and STANDARD mode. Available on DL modules in DATA mode only. www.caralarm.com Omega Research & Development Inc. 0
Page 3 of OL-AL(MDB)-GM Doc. No.: ##887## 003 COMPOnEnT LOCATOr A D B C www.caralarm.com Omega Research & Development Inc. 0
Page 4 of OL-AL(MDB)-GM Doc. No.: ##887## 003 KnOwLEDgE BASE HOw TO TEST THE new generation PASSLOCK wire The Passlock wire s voltage can vary according to the ignition s position. Although a small variation can occur when using a voltmeter, the Passlock wire should reflect the following results: On Key sense, the wire tests ± VDC On Accessory, the wire tests ±0 VDC With the ignition ON, the wire tests ±4.0 VDC Upon start, the wire tests ±3 VDC When learning the module to the vehicle, consider the module have to read 0 identical voltage values on every key position before validating all the Passlock values. Give the module enough time into every key position to acquire its accurate sampling (follow the module LED reactions as found in the programming procedure). warning! The vehicles equipped with a new generation Passlock system usually don t have any (+) Start wire. The vehicle monitors the Passlock wire and the Accessory Power Drop while the ignition is ON to determine proper crank timing. Do not connect the remote starter (+) start wire to the vehicle. ADVAnCED DiAgnOSTiC (Available only on 3K, 64K and 8K microcontrollers) Did you know the module will display its configuration information in the vehicle info center found in the instrument panel cluster or on the radio display. The module will automatically broadcast the information at the end of its learn sequence. You can also recall the information at any time by turning the key to the ON position and once the key is turned ON, press and hold down the programming button for seconds and then release it. The information displayed will be: Install Type PK3 Detected Passlock value at ignition Passlock value at start Keyless configuration Year matching VIN Auto Relock configuration new generation PASSLOCK/PK3+ TAMPEr MODE The new generation Passlock system is equipped with an anti theft countdown. When a failure to provide the vehicle the expected Passlock value, the vehicle will lock itself in Tamper Mode. Depending on various criteria, the vehicle BCM will evaluate the security breach and will decide if it locks itself in regular or bad Passlock tamper mode or in PK3 tamper mode. PASSLOCK TAMPEr MODE SYMPTOMS The vehicle starts, ECM shuts off the fuel injectors and the security indicator starts blinking in the instrument panel cluster. To exit Passlock Tamper Mode, repair the failure in question. During the following steps, make sure the battery is fully charged (it is recommend to apply e-brake to turn off DTRL on Canadian vehicles). Turn the vehicle ignition ON, move the key to the START position and bring it back to the ON position before the car started. Leave the key to the ON position. The security indicator will start blinking. After 0 minutes, the security indicator will stop blinking, turn ON solid, then turn OFF. Turn the vehicle ignition to the OFF position, wait 5 seconds and then attempt to start the vehicle. If the vehicle starts, wait for the security indicator to turn OFF before you turn off the engine. If the vehicle fails to start, keep the ignition ON, you are in BAD Tamper mode and may have to repeat the entire sequence up to 3 times which may take over 30 minutes. There s no solution to get the vehicle out of Tamper Mode faster then waiting the required delays in each cycles. PK3 TAMPEr MODE SYMPTOMS The vehicle doesn t start and the info center indicates a PK3+ failure. To exit PK3+ Tamper Mode, repair the failure in question. Close all vehicle doors Wait at least 3 minutes. Then start the vehicle using a valid key. The vehicle should start. If the vehicle refuses to start, unplug the vehicle battery for 30 seconds, then reconnect the battery and start the vehicle again. If the circuitry is properly connected and a valid key is used, the vehicle will start. www.caralarm.com Omega Research & Development Inc. 0
Page 5 of OL-AL(MDB)-GM Doc. No.: ##887## 003 TYPE - wire CrOSS reference CHArT CONNECTOR MAKE MODEL YEAR DESCRIPTION CHEVROLET NAME TYPE POSITION PONTIAC POLARITY MODULE LOCATION COMPONENT LOCATOR Cobalt 05-06 HHR 06 Malibu Classic Malibu MAXX 04-07 04-06 G6 05-06 Pursuit / G5 05-06 Solstice 06 V ~ Green 6 pin Red/White (+) Ignition switch A V ~ Black 5 pin Red/White (+) PK3+ A Data (SWC) OBDII ~ 6 pin Green (DATA) OBDII D Data (Keyless) C White 7 pin Tan/White or LtGreen (DATA) BCM B V ~ Green 6 pin Red/White (+) Ignition switch A V ~ Black 5 pin Red/White (+) PK3+ A Data (SWC) OBDII ~ 6 pin Green (DATA) OBDII D Data (Keyless) C White 7 pin Tan/White or LtGreen (DATA) BCM B V ~ Green 6 pin Red/White (+) Ignition switch A V ~ Black 5 pin Red/White (+) PK3+ A Data (SWC) OBDII ~ 6 pin Green (DATA) OBDII D Data (Keyless) C White 7 pin Tan/White or LtGreen (DATA) BCM B V ~ Green 6 pin Red/White (+) Ignition switch A V ~ Black 5 pin Red/White (+) PK3+ A Data (SWC) OBDII ~ 6 pin Green (DATA) OBDII D Data (Keyless) C White 7 pin Tan/White or LtGreen (DATA) BCM B V ~ Green 6 pin Red/White (+) Ignition switch A V ~ Black 5 pin Red/White (+) PK3+ A Data (SWC) OBDII ~ 6 pin Green (DATA) OBDII D Data (Keyless) C White 7 pin Tan/White or LtGreen (DATA) BCM B V ~ Green 6 pin Red/White (+) Ignition switch A V ~ Black 5 pin Red/White (+) PK3+ A Data (SWC) OBDII ~ 6 pin Green (DATA) OBDII D Data (Keyless) C White 7 pin Tan/White or LtGreen (DATA) BCM C www.caralarm.com Omega Research & Development Inc. 0
Page 6 of OL-AL(MDB)-GM Doc. No.: ##887## 003 TYPE - wiring DIAGRAM PASSLOCK IGN (+) IGNITION SWITCH PK3+ PK3+ CONNECTOR - BLACK 5 4 3 6 ACC (+) 5 4 3 V (+) IGNITION SWITCH CONNECTOR - WHITE REMOTE STARTER V (+) IF THERE IS NO PK3+ CONNECTOR IGNORE RED/WHITE CUT IGN (+) ACC (+) TACH (AC) INPUT TRUNK/TAILGATE WINDOW RELEASE (-) OUTPUT UNLOCK (-) OUTPUT LOCK (-) OUTPUT GROUND (-) GWR (-) OUTPUT DATA MODE OPTIONAL -> TRUNK STATUS (-) INPUT OPTIONAL -> DOOR STATUS (-) INPUT N/A LEGEND NOT REQUIRED IN DATA MODE (-WAY) NOT REQUIRED IN DATA MODE (-WAY) USE DATA MODE OR HARD MODE GWR (-) INPUT - BLUE/WHITE (NC) WHITE GROUND - BLACK V (+) - RED LOCK/ARM (-) INPUT - GREEN/BLACK UNLOCK/DISARM (-) INPUT - BLUE/BLACK TRUNK/TAILGATE WINDOW RELEASE (-) INPUT - RED/WHITE (NC) BROWN (NC) PURPLE/YELLOW (NC) PURPLE/BLACK AUTO-RELOCK (+) INPUT - WHITE ACCESSORY (+) INPUT - BLACK/WHITE RAP SHUTDOWN (-) OUTPUT - GREEN *TACH (AC) OUTPUT - PURPLE/WHITE CONNECT TO DRIVER DOOR SWITCH TO TURN OFF RADIO AT THE END OF THE REMOTE START SEQUENCE CONNECT TO CONSTANT V (+) TO ENABLE AUTOMATIC RELOCK AFTER START OBDII CONNECTOR LOCATED UNDER DRIVER SIDE DASH DATA MODE BCM WHITE/BLACK - PK3 (+) VEHICLE SIDE WHITE/RED - PK3 (+) KEY SIDE WHITE (NC) YELLOW/BLACK - DOOR STATUS (-) OUTPUT* YELLOW/RED - TRUNK STATUS (-) OUTPUT* YELLOW - PASSLOCK BROWN/RED (NC) BROWN/YELLOW (NC) ORANGE/BLACK - DATA (KEYLESS) ORANGE/WHITE (NC) ORANGE - DATA (SWC) PINK/BLACK (NC) PINK - IGNITION (+) INPUT BLUE/RED (NC) BLUE/YELLOW (NC) GREEN/RED (NC) GREEN/YELLOW (NC) GRAY/RED (NC) GRAY/YELLOW (NC) C - WHITE DATA (KEYLESS) 3 4 5 6 7 8 55 7 9 0 DATA (SWC) 3 4 5 6 8 www.caralarm.com Omega Research & Development Inc. 0
Page 7 of OL-AL(MDB)-GM Doc. No.: ##887## 003 TYPE - wire CrOSS reference CHArT CONNECTOR MAKE MODEL YEAR DESCRIPTION CHEVROLET NAME TYPE POSITION PONTIAC POLARITY MODULE LOCATION COMPONENT LOCATOR Cobalt 07-0 HHR 07- Malibu Malibu Hybrid Malibu MAXX 07-08- 07-09 G6 07-09 Pursuit / G5 07-0 Solstice 07-09 V ~ Green 6 pin Red/White (+) Ignition switch A Data (SWC) OBDII ~ 6 pin Green (DATA) OBDII D Security Light C White 7 pin DkGreen (DATA) BCM B V ~ Green 6 pin Red/White (+) Ignition switch A Data (SWC) OBDII ~ 6 pin Green (DATA) OBDII D Security Light C White 7 pin DkGreen (DATA) BCM B V ~ Green 6 pin Red/White (+) Ignition switch A Data (SWC) OBDII ~ 6 pin Green (DATA) OBDII D Security Light C White 7 pin DkGreen (DATA) BCM B V ~ Green 6 pin Red/White (+) Ignition switch A Data (SWC) OBDII ~ 6 pin Green (DATA) OBDII D Security Light C White 7 pin DkGreen (DATA) BCM B V ~ Green 6 pin Red/White (+) Ignition switch A Data (SWC) OBDII ~ 6 pin Green (DATA) OBDII D Security Light C White 7 pin DkGreen (DATA) BCM B V ~ Green 6 pin Red/White (+) Ignition switch A Data (SWC) OBDII ~ 6 pin Green (DATA) OBDII D Security Light C White 7 pin DkGreen (DATA) BCM C www.caralarm.com Omega Research & Development Inc. 0
Page 8 of OL-AL(MDB)-GM Doc. No.: ##887## 003 TYPE - wire CrOSS reference CHArT CONNECTOR MAKE MODEL YEAR DESCRIPTION SATURN NAME TYPE POSITION POLARITY MODULE LOCATION COMPONENT LOCATOR Aura / Hybrid 07-0 Sky 07-09 V ~ Green 6 pin Red/White (+) Ignition switch A Data (SWC) OBDII ~ 6 pin Green (DATA) OBDII D Security Light C White 7 pin DkGreen (DATA) BCM B V ~ Green 6 pin Red/White (+) Ignition switch A Data (SWC) OBDII ~ 6 pin Green (DATA) OBDII D Security Light C White 7 pin DkGreen (DATA) BCM C www.caralarm.com Omega Research & Development Inc. 0
Page 9 of OL-AL(MDB)-GM Doc. No.: ##887## 003 TYPE - wiring DIAGRAM IGNITION SWITCH BCM C - WHITE SECURITY LIGHT 55 7 8 PASSLOCK IGN (+) DATA (SWC) 3 4 5 6 7 8 6 5 4 3 ACC (+) V (+) IGNITION SWITCH CONNECTOR - WHITE REMOTE STARTER 9 0 3 4 5 OBDII CONNECTOR LOCATED UNDER DRIVER SIDE DASH 6 IGN (+) ACC (+) TACH (AC) INPUT TRUNK/TAILGATE WINDOW RELEASE OUTPUT UNLOCK (-) OUTPUT LOCK (-) OUTPUT GROUND (-) GWR (-) OUTPUT DATA MODE REQUIRED -> BRAKE (+) INPUT REQUIRED -> E-BRAKE STATUS (-) INPUT OPTIONAL -> TRUNK STATUS (-) INPUT OPTIONAL -> DOOR STATUS (-) INPUT N/A LEGEND NOT REQUIRED IN DATA MODE (-WAY) NOT REQUIRED IN DATA MODE (-WAY) USE DATA MODE OR HARD MODE GWR (-) INPUT - BLUE/WHITE (NC) WHITE GROUND - BLACK V (+) - RED LOCK/ARM (-) INPUT - GREEN/BLACK UNLOCK/DISARM (-) INPUT - BLUE/BLACK TRUNK/TAILGATE WINDOW REL. (-) INPUT - RED/WHITE (NC) BROWN SECURITY LIGHT - PURPLE/YELLOW (NC) PURPLE/BLACK AUTO-RELOCK (+) INPUT - WHITE ACCESSORY (+) INPUT - BLACK/WHITE RAP SHUTDOWN (-) OUTPUT - GREEN *TACH (AC) OUTPUT - PURPLE/WHITE CONNECT TO DRIVER DOOR SWITCH TO TURN OFF RADIO AT THE END OF THE REMOTE START SEQUENCE CONNECT TO CONSTANT V (+) TO ENABLE AUTOMATIC RELOCK AFTER START DATA MODE WHITE/BLACK - PASSLOCK CONNECTOR SIDE WHITE/RED - PASSLOCK VEHICLE SIDE WHITE (NC) YELLOW/BLACK - DOOR STATUS (-) OUTPUT* YELLOW/RED - TRUNK STATUS (-) OUTPUT* YELLOW - PASSLOCK BROWN/RED (NC) BROWN/YELLOW (NC) ORANGE/BLACK (NC) ORANGE/WHITE (NC) ORANGE - DATA (SWC) PINK/BLACK (NC) PINK - IGNITION (+) INPUT BLUE/RED - SECURITY LIGHT BCM SIDE BLUE/YELLOW - SECURITY LIGHT VEHICLE SIDE GREEN/RED - E-BRAKE STATUS (-) OUTPUT* GREEN/YELLOW (NC) GRAY/RED - BRAKE (+) OUTPUT* GRAY/YELLOW (NC) www.caralarm.com Omega Research & Development Inc. 0
Page 0 of OL-AL(MDB)-GM Doc. No.: ##887## 003 installation MODE SELECTiOn Press and release programming button to select installation mode. LED flashes (X) once = DATA MODE LED flashes (X) twice = STANDARD HARD MODE! Press and hold programming button until LED turns solid GREEN to register selection. After registration, follow Factory Reset Procedure to change installation mode and restart this procedure. MODULE PrOgrAMMing PrOCEDUrE Close driver door. 5 Turn key to Start position and Hold for 3 seconds. START Re-open driver door to wake up data bus. 6 ON Release key from Start position and return to ON position. Insert key into ignition. Wait 3 seconds. Wait, LED will turn solid GREEN for seconds. 3 Turn key to Accessory position. 7 OFF Turn key to OFF position. ACC Wait 3 seconds. 4 Turn key to ON position. 8 Module Programming Procedure completed. ON Wait 3 seconds. www.caralarm.com Omega Research & Development Inc. 0
Page of OL-AL(MDB)-GM Doc. No.: ##887## 003 identify VEHiCLE YEAr Locate the Vehicle Identification Number (VIN) and identify the 0th character. 4 3 A 5 Y N 5 T A L 8 D 5 R 0 X Match the VIN s 0th character to its corresponding year. L > 990 S > 995 Y > 000 5 > 005 A > 00 M > 99 T > 996 > 00 6 > 006 B > 0 N > 99 V > 997 > 00 7 > 007 C > 0 P > 993 W > 998 3 > 003 8 > 008 D > 03 R > 994 X > 999 4 > 004 9 > 009 E > 04 LED STATUS Flashing RED DIAGNOSTICS DURING PROGRAMMING DURING REMOTE START WITH IGNITION OFF Missing/wrong information from firmware or vehicle Incorrectly programmed Solid RED Waiting for more vehicle information Incorrectly programmed Flashing GREEN Additional steps required to complete programming MODULE DiAgnOSTiCS Correctly programmed and operational Incorrectly programmed or connected Not programmed waiting for more vehicle information False ground when running status from remote starter Solid GREEN then OFF Correctly programmed Reset in progress Reset in progress OFF No activity or already programmed Invalid ground when running status from remote starter At rest and ready for a remote start sequence FACTOrY reset PrOCEDUrE DISCONNECT all connectors from module EXCEPT the black 4-PIN standard or optional data connector. DISCONNECT black 4-PIN standard or optional data connector. 5 6 LED will turn solid red for seconds. RESET COMPLETED. RECONNECT all connectors. 3 4 PRESS AND HOLD programming button while connecting either 4-PIN standard or optional data connector. When LED flashes red, RELEASE programming button. 7! Repeat programming procedure. Failure to follow procedure may result with a DTC or a CHECK ENGINE error message. This product is protected by one or more of the following patents: U.S. LETTErS PATEnT no. 5,79,55; 6,0,460; 6,43,004; 6,49,6; 6,75,47; 6,97,73; 6,346,876; 6,39,534; 6,59,4; 6,696,97; 6,756,885; 6,756,886; 6,77,67; 6,8,89; 6,94,750; 7,00,40; 7,03,86; 7,046,6; 7,06,37; 7,068,53; 7,05,830; 7,05,679; 7,4,083; 7,369,936; 7,378,945; 7,489,33; 7,50,937; CAnADiAn PATEnT no.,30,48;,45,03;,46,670;,44,99;,45,0;,45,07;,45,038;,45,04;,50,893;,45,490;,45,96;,45,487; EUrOPEAn PATEnT no.,053,8; DE 69807-94T; U.S. 00045535; 006098; 0060984; 00400784; 008003036; 009007955; EP500565; 538038; 538037; www.caralarm.com Omega Research & Development Inc. 0