CME5-5 A-R-I-E-AQQE S-A-D-N

GRUNDFOS DATA BOOKLET CME5-5 A-R-I-E-AQQE S-A-D-N Grundfos pump 98396719 Thank you for your interest in our products. Please contact us for more information, or visit our website https://www.lenntech.com/grundfos/cmebasis/98396719/cme5-5-a-r-i-e-aqqe.html info@lenntech.com tel. +31 152 610 900 fax. +31 152 616 289 BE > THINK > INNOVATE

Position Qty. Description 1 CME5-5 A-R-I-E-AQQE Product No.: On request Compact, reliable, horizontal, multistage, end-suction centrifugal pump with axial suction port and radial discharge port. Pump materials in contact with the liquid are in stainless steel. The mechanical shaft seal is a special designed, unbalanced O-ring seal. Pipework connection is via internal Whitworth pipe threads, Rp (ISO 7/1). The pump is fitted with a 3-phase, fan-cooled, permanent-magnet, synchronous motor. The motor efficiency is classified as IE5 in accordance with IEC 60034-30-2. The motor includes a frequency converter and PI controller in the motor terminal box. This enables continuously variable control of the motor speed, which again enables adaptation of the performance to a given requirement. An operating panel on the motor terminal box enables setting of required setpoint as well as setting of pump to "Min." or "Max." operation or to "Stop". The Grundfos Eye indicator on the operating panel provides visual indication of pump status: "Power on": Motor is running (rotating green indicator lights) or not running (permanently green indicator lights) "Warning": Motor is still running (rotating yellow indicator lights) or has stopped (permanently yellow indicator lights) "Alarm": Motor has stopped (flashing red indicator lights). Communication with the pump is possible by means of Grundfos GO Remote (accessory). The remote control enables further settings as well as reading out of a number of parameters such as "Actual value", "Speed", "Power input" and total "Power consumption". The terminal box holds terminals for these connections: one dedicated digital input two analog inputs, 0(4)-20 ma, 0-5 V, 0-10 V, 0.5-3.5 V 5 V voltage supply to potentiometer and sensor one configurable digital input or open-collector output Grundfos Digital Sensor input and output 24 V voltage supply for sensors two signal-relay outputs (potential-free contacts) GENIbus connection interface for Grundfos CIM fieldbus module. Further product details Pump and motor are integrated in a compact and user-friendly design. The pump is fitted to a low base plate, making it ideal for installation in systems where compactness is important. The state-of-the-art design and materials of the shaft seal ensure high wear resistance, improved sticking and dry-running capabilities and long operating life. Servicing the pump requires no special service tools. Service parts are in stock for quick delivery and are available as kits, single parts or bulk. Service videos are available on www.youtube.com. Frequency converter operation offers these functions: - controlled operation, i.e. consumption flucturates - constant pressure - communication with the pump. Adaption of performance through frequency-controlled speed offers obvious benefits such as: - energy savings - increased comfort 1/12

Position Qty. Description - control and monitoring of the application and pump performance. An operating panel on the motor terminal box enables setting of required setpoint as well as setting of pump to "Min." or "Max." operation or to "Stop". The Grundfos Eye indicator on the operating panel provides visual indication of pump status: "Power on": Motor is running (rotating green indicator lights) or not running (permanently green indicator lights) "Warning": Motor is still running (rotating yellow indicator lights) or has stopped (permanently yellow indicator lights) "Alarm": Motor has stopped (flashing red indicator lights). Communication with the pump is possible by means of Grundfos GO Remote (accessory). The remote control enables further settings as well as reading out of a number of parameters such as "Actual value", "Speed", "Power input" and total "Power consumption". Pump A combination of a stop ring and a Nord-lock washer secures a tight and reliable fixation of the impeller spacing pipes to the splined pump shaft. It is possible to remove and fit the hydraulic parts from the pump side. The inlet and outlet port are integrated in the pump sleeve. The inlet part, chambers and discharge part are hold together by four staybolts and a retaining flange. The pump is fitted with an unbalanced O-ring seal with a rigid torque-transmission system. It has a fixed seal driver ensuring a reliable rotation of all parts. The dynamic secondary seal is an O-ring. Primary seal: Rotating seal ring material: silicon carbide (SiC) Stationary seat material: silicon carbide (SiC) This material pairing is used where higher corrosion resistance is required. The high hardness of this material pairing offers good resistance against abrasive particles. Secondary seal material: EPDM (ethylene-propylene rubber) EPDM has excellent resistance to hot water. EPDM is not suitable for mineral oils. The pump shaft is connected to the motor shaft through a left thread and tight fit. The shaft cannot be dismantled. Motor The motor is a totally enclosed, fan-cooled motor with principal dimensions to EN 50347. Electrical tolerances comply with EN 60034. The motor efficiency is classified as IE5 in accordance with IEC 60034-30-2. The motor requires no external motor protection. The motor control unit incorporates protection against slow- and quick-rising temperatures, e.g. constant overload and stalled conditions. The terminal box holds terminals for these connections: one dedicated digital input two analog inputs, 0(4)-20 ma, 0-5 V, 0-10 V, 0.5-3.5 V 5 V voltage supply to potentiometer and sensor one configurable digital input or open-collector output Grundfos Digital Sensor input and output 24 V voltage supply for sensors two signal-relay outputs (potential-free contacts) GENIbus connection interface for Grundfos CIM fieldbus module. Technical data Liquid: Pumped liquid: Water Liquid temperature range: -20.. 120 C 2/12

Position Qty. Description Liquid temperature during operation: 20 C Density: 998.2 kg/m³ Technical: Rated flow: Rated head: Primary shaft seal: Approvals on nameplate: Curve tolerance: Materials: Pump housing: Impeller: Rubber: 5.6 m³/h 55.6 m AQQE CE,TR,CURUS,EAC ISO9906:2012 3B Stainless steel DIN W.-Nr. 1.4301 AISI 304 Stainless steel DIN W.-Nr. 1.4301 AISI 304 EPDM Installation: Maximum ambient temperature: 40 C Maximum operating pressure: 16 bar Max pressure at stated temp: 10 bar / 120 C 16 bar / 90 C Flange standard: WHITWORTH THREAD RP Pump inlet: Rp 1 1/4 Pump outlet: Rp 1 Electrical data: Motor type: IE Efficiency class: Rated power - P2: Mains frequency: Rated voltage: Rated current: Rated speed: Enclosure class (IEC 34-5): Insulation class (IEC 85): 90D IE5 2.2 kw 50 Hz 3 x 380-500 V 4.15-3.40 A 360-4000 rpm IP55 F Others: Minimum efficiency index, MEI : 0.7 Net weight: 18.6 kg Gross weight: 22.1 kg Danish VVS No.: 385232050 3/12

On request CME5-5 A-R-I-E-AQQE 50 Hz H [m] CME5-5, 3*400 V eta [%] 75 70 100 % 65 60 55 90 % 50 45 80 % 90 40 80 35 70 % 70 30 25 60 % 60 50 20 15 10 50 % 40 % 40 30 20 5 21 % 10 0 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 6.5 7.0 7.5 P [kw] Q [m³/h] 0 NPSH [m] 2.0 P1 (motor+freq.converter) 20 P2 1.5 15 1.0 10 0.5 5 0.0 0 4/12

Rp 3/8 Rp 3/8 10.5 Rp 1 1/4 Rp 1 248.3 180.6 410.5 155 212.7 178 197.7 139.8 125 267 105.1 197.8 107.6 302.9 Description Value General information: Product name: CME5-5 A-R-I-E-AQQE Product No: On request EAN number: On request Technical: Rated flow: 5.6 m³/h Rated head: 55.6 m Impellers: 5 Primary shaft seal: AQQE Approvals on nameplate: CE,TR,CURUS,EAC Curve tolerance: ISO9906:2012 3B Pump version: A Model: A Materials: Pump housing: Stainless steel DIN W.-Nr. 1.4301 AISI 304 Impeller: Stainless steel DIN W.-Nr. 1.4301 AISI 304 Material code: I Rubber: EPDM Code for rubber: E Installation: Maximum ambient temperature: 40 C Maximum operating pressure: 16 bar Max pressure at stated temp: 10 bar / 120 C 16 bar / 90 C Flange standard: WHITWORTH THREAD RP Pump inlet: Rp 1 1/4 Pump outlet: Rp 1 Connect code: R Liquid: Pumped liquid: Water Liquid temperature range: -20.. 120 C Liquid temperature during operation: 20 C Density: 998.2 kg/m³ Electrical data: Motor type: 90D IE Efficiency class: IE5 Rated power - P2: 2.2 kw Mains frequency: 50 Hz Rated voltage: 3 x 380-500 V Rated current: 4.15-3.40 A Rated speed: 360-4000 rpm Enclosure class (IEC 34-5): IP55 Insulation class (IEC 85): F Others: Minimum efficiency index, MEI : 0.7 Net weight: 18.6 kg Gross weight: 22.1 kg Config. file no: 98499054 Danish VVS No.: 385232050 H [m] 75 70 65 60 55 50 45 40 35 30 25 20 15 10 5 100 % 90 % 80 % 70 % 60 % 50 % 40 % 21 % CME5-5, 3*400 V 0 0 1 2 3 4 5 6 7 Q [m³/h] P [kw] Rp 3/8 2.0 1.5 1.0 0.5 0.0 10.5 L1 L2 L3 PE 267 139.8 178 90.3 180.6 248.3 NC L1 L2 L3 197.8 302.9 125 155 0 eta [%] 90 80 70 60 50 40 30 20 10 15 10 5 0 NPSH [m] P1 (motor+freq.converter) 20 410.5 105.1 107.6 212.7 197.7 P2 Rp 1 Rp 3/8 Rp 1 1/4 C1 NO NC C2 +24 V* OC DI GND NO 10 DI3/OC1 4 AI1 +24 V* +24 V* +24 V*/5 V* 2 DI1 5 +5 V 6 GND A GENIbus A Y GENIbus Y B GENIbus B 3 GND 15 +24 V 8 +24 V +24 V* +24 V* +24 V*/5 V* 26 +5 V 23 GND 25 GDS TX 24 GDS RX +5 V* 7 AI2 5/12

On request CME5-5 A-R-I-E-AQQE 50 Hz cos phi eta CME5-5 + 90D 2.2 kw 3*400 V, 50 Hz I [A] cos phi eta 0.8 4.0 I 0.6 3.0 0.4 2.0 0.2 1.0 0.0 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 2.0 2.1 n [rpm] P2 [kw] 0.0 P1 [kw] n 3000 3.0 P1 (motor+freq.converter) 2000 2.0 1000 1.0 0 n = 100 % 0.0 6/12

On request CME5-5 A-R-I-E-AQQE 50 Hz 90.3 180.6 Rp 3/8 10.5 267 139.8 178 302.9 Rp 1 197.8 105.1 107.6 Rp 1 1/4 125 212.7 Rp 3/8 155 197.7 410.5 248.3 Note! All units are in [mm] unless others are stated. Disclaimer: This simplified dimensional drawing does not show all details. 7/12

Exploded view 251a 251d 77 28 7 7a 17 301a 219 92 301a 11 9 92 51 11b 105 100 215a 215 66a 67 49 45 18 530a 530 215a 217 531a 534 531 534a 6 8/12

Sectional drawing (TM058200 for TPE2,TPE3) 5 4 3 2 1 TM058200 9/12

Exploded view ( TM057026 for MGE model H/I ) 251d 251b 291 290 293 287 287a 502 277a 273b 277 252a 286 273a 273 275a 266 268 268a 289a 289 251a 288b 288 288a 252b 159e 157 158 150 156c 156 151 152 172 154 185 178 156d 187 153 188 191 156c 156b 192 159d 10/12

Parts list CME5-5, Product No. On request Valid from 2.1.2013 (1301) Pos Description Annotation Données de classification Référence Quantité Unité + MGE90D 1 pcs Cross recess countersunk screw 4 pcs - 4 Chamber cpl. 3 pcs Guide vane 6 Plate 1 Retainer 1 Intermediate chamber 1 Vane 1 45 Neck ring 1 65 Retainer 1-4.d Chamber cpl. 1 pcs Chamber 1 Retainer for seal ring 1 Guide vane 6 Plate 1 Vane 1 45 Neck ring 1 65 Neck ring retainer 1-5a Chamber cpl. 1 pcs Retainer 1 Intermediate chamber 1 Vane 1 45 Neck ring 1 65 Retainer 1 6.a Flange 1 pcs 16 Collar sleeve cpl. 1 pcs - 25 Drain plug cpl. 2 pcs 11 O-ring Diameter: 18,5 1 Material type: EPDM Thickness: 2 25 Plug 1 31 O-ring Diameter: 114 1 pcs Material type: EPDM Thickness: 3,9-32 Cover plate 1 pcs Cover plate 1 Plate 1 36 Lock nut Thread: M8 1 pcs 49 Impeller cpl. 5 pcs 51 Pump shaft Diameter: D12 1 pcs 64 Spacing pipe 4 pcs 64.c Clamp 1 pcs 66 Wedge lock washer 1 pcs 76 Nameplate 2 pcs - 105 Shaft seal 1 pcs 102 O-ring Diameter: 17,86 1 Material type: EPDM Thickness: 2,62 103 Seal ring, stationary 1 104 Seal ring, rotating 1 107 O-ring 1 108 Compression spring 1 111 Retainer 1 112 Driver for shaft seal 1 111.a Stop ring 1 pcs 151 Fan cover 1 pcs 152 Pan head thread forming screw 4 pcs 156 Fan 1 pcs 181 Hex socket head cap screw Length (mm): 115 4 pcs 11/12

Pos Description Annotation Données de classification Référence Quantité Unité Thread: M8 191 Foot 1 pcs 12/12

Disclaimer: The information about the Grundfos pump in this document may be outdated. Data may be subject to alterations without further notice. Please contact us to verify the data above is still accurate/up-to-date. All information is copyright Grundfos. info@lenntech.com https://www.lenntech.com tel. +31 152 610 900 fax. +31 152 616 289