INTRODUCTION WALL MOUNT APPLICATIONS SLIMLINE BOX... 5 COMMSRAK... 5 IMRAK 400... 6-7 IMRAK 600... 8-9 FLOOR MOUNT APPLICATIONS COMMSRAK... 11 IMRAK 600... 12-15 IMRAK 1400... 16-32 Specification... 17-18 Dimensions... 19 Building Your Own System... 20-21 Doors and Rear Panels... 22 Side Panels, Top Covers... 24-25 Gland Plates, Baying Kits... 25-26 Castors, Adjustable Feet, Lifting Eye, Bolting Down Plate... 27 Plinths... 28 IMRAK 1400, 1200mm Wide... 29-32 VERAK IP... 34-35 VERAK EMC... 38-41 GENERAL ACCESSORIES... 42-57 Panel Mounts and Supports... 42-43 Chassis Supports, Trays and Shelves... 44-45 Desk Units and Drawer Units... 47 Keyboard/Keyboard Housing... 47 Swing Frames... 48 Thermal Management... 49 Earth Continuity Kit... 50 Cable Management... 51 Electrical Panels... 52 Front Panels and Screws... 53-54 Power Distribution Panels... 55-56 Fire protection unit... 57 Light... 57 NETWORKING SOLUTIONS... 58-60 Fibre optic 19" Shelves... 58 Fibre optic 19" Front Panels... 58 Wall Cabinet for Fibre Applications... 59 110 Tower Unit... 60 110 PDS Panel... 60 ACCESSORIES CODING KEY The following codes denote the product for which accessories can be used. IMRAK 600... IMRAK 1400... VERAK... The IMRAK family is a suite of products built expressly for the network professional. Each product has been designed with specific features to simplify the process of network installation and solve many of the problems encountered when installing, operating and maintaining computer networks. Much attention was also paid to the appearance of the products. So much in fact that a number of IF design awards were presented to VERO Electronics in recognition of their achievements with the IMRAK family. IMRAK WALL MOUNTING IMRAK 400 The IMRAK 400 series is a range of wall mounted enclosures for office environments where a reduced amount of U height and internal depth (300 to 500mm versions) are required. The aesthetics match the IMRAK 600 and IMRAK 1400 creating a pleasing and professional looking, integrated appearance to all network components. Optional mounting, hinged and panel mounting arrangements create a variety of equipment mounting and access arrangements so that the IMRAK 400 can be used in almost all locations, no matter how seemingly inaccessible. IMRAK 600 IMRAK 600 IMRAK 600 cabinets provide an economic solution for applications when side access is not required. Aesthetically, it fits the IMRAK range with a plan size of 600 x 600mm and can be used on the same installation while maintaining the same overall visual effect. Available as freestanding or wall mounted versions, many accessories are common to the IMRAK range meaning that configuration changes can be easily accommodated both during installation and later operation and maintenance. Certificate Number Chandlers Ford FM 00424 Uxbridge Q 06146 Many of the products in this Section are manufactured at our Chandlers Ford or Uxbridge facilities in accordance with BS EN ISO9001. For further details contact our Quality department. 2
IMRAK 1400 VERAK IP & EMC CUSTOMISED IMRAK IMRAK 1400 The IMRAK 1400 range are freestanding cabinets suitable for office, equipment room and cabling closet installation. Attention to styling, with attractive two tone grey paint and green trim highlights with a smoked glass door mean that the IMRAK 1400 can be used in any office environment. However IMRAK 1400 is still an exceptionally rugged and strong cabinet enabling it to be used for all applications VERAK VERAK is the latest range of large rack systems developed by VERO Electronics. Available in IP55 and EMC screened versions, VERAK builds on the experience gained by VERO as a market leader in network applications. VERAK is available in IP55, EMC and combined IP& EMC formats in heights of 27 to 42U and 600 x 600, 600 x 800 and 800 x 800 plan sizes. The IP and EMC versions of VERAK are intended for separate markets. The IP version addresses the emergent industrial networking sectors, while the EMC version with its high level screening is suitable for the electronics and telecoms industries. VERO's extensive experience in rack manufacture has ensured that typical problems of cable access and thermal management in racks has been considered and resolved to optimise the racks performance. Consistent with VERO's integrated approach the VERAK range has been designed to accept the complete range of IMRAK internal fitting such as 19" panel mounts, cross members, cable troughs and trays and power distribution products. Where necessary most of our standard racks are easily modified to suit individual customer requirements or applications. Customising options include special sizes, heights, widths and depths, screen printing, surface or subsurface, paint colour, engraving, punching and drilling. Further details are available from your local sales office. 3
NETWORKING - WALL MOUNT APPLICATIONS INTRODUCTION VERO has developed a range of products to suit the requirement of wall mounting your Networking application. The products detailed in this section start with a slim 2.5U key cabinet style enclosure, suitable for such applications as fibre breakout or local patching and progress through a comprehensive range to a 22U 600mm deep cabinet, suitable for modems, patching and active equipment. All the products are designed to the very highest standards and through controlled Industrial Design, ensure that whatever combination is used, your installation will look professional, attractive and well managed. The most visible aspect to any Network is the furniture used to house that Network and you should feel as proud of its appearance as you do the Network performance. All VERO products are designed to be flexible and delivered to your requirements. There is a full range of accessories available, which can be supplied with the cabinets, to ensure your onsite installation time is kept to a minimum. PRODUCTS AVAILABLE SLIMLINE CABINET - 2.5U x 19 key cabinet style enclosure COMMSRAK - 12U, 37U, 42U x 19 open frame rack with integral cable management IMRAK 400-6U, 9U, 12U, 15U x 19 cabinet in depths from 300mm to 500mm IMRAK 600-12U, 17U, 22U x 19 cabinet in 600mm depth SLIMLINE CABINET COMMSRAK IMRAK 400 IMRAK 600 4
NETWORKING - WALL MOUNT APPLICATIONS SLIMLINE CABINET 2.5U x 19 key cabinet style enclosure FEATURES Low profile for exposed positions Key lock Wall mounting slots in back panel Multi access gland facilities Internal protection plate for additional security Colour matched for coordinated installations Supplied with drilling template for wall The cabinet can also be used for housing other networking components such as data distribution panels. Top and base Colours : 1,2mm Zintec coated steel : Pale grey RAL 7035 base Dusty grey RAL 7037 door Height 500mm Width 335mm Depth 115mm SLIMLINE CABINET Cabinet 960-254426A Earth Kit 801-231543C COMMSRAK 12U, 37U, 42U x 19 open frame rack with integral cable managment. FEATURES All round accessibility Integral cable management Colour matched for coordinated installations Supplied flat pack with single type fixings and tooling Optional earth bonding facility Shelving accessories available for modems etc 286mm or 400mm offset from wall to 19 mounts Load rating up to 150kgs Steel painted pale grey RAL 7035 Ordering Information Order Code 12U frame 52-255052B 37U frame 52-255051E 42U frame 52-255050H 286mm wall mount kit 52-251177J 400mm wall mount kit 52-257133A Earth kit 52-248075G Cantilever chassis support 802-563106A Chassis tray 256mm 802-561013G 255mm cantilever shelf 802-562284D 12U WALL MOUNTED COMMSRAK Note: These items can be configured (N) to provide complete kits for delivery. 5
NETWORKING - WALL MOUNT APPLICATIONS IMRAK 400 6U, 9U, 12U, 15U x 19 cabinet in depths from 300mm to 500mm Supplied fully assembled for quick installation Available with toughened glass or metal door Available as single section cabinet or two section (rear access) cabinet 4 height options - 6U (364mm o/all), 9U (497mm o/all), 12U (630mm o/all) and 15U (764mm o/all) All cabinets are industry standard 600mm wide 4 depth options - 300mm single section 400mm single section 400mm two section 500mm two section Optional earth bonding facility Shelving accessories available for modems etc Colour matched for coordinated installations Cable entry positions in top and bottom of all sections Load rating of 20kgs for two section and 40kgs for single section Supplied with drill template for wall Choice of colour ident on glass (standard is green) Available with either standard key locks or swing handles for additional security Choice of locks for swing handle Adjustable 19 panel mounts supplied as standard MATERIAL AND FINISH Zintec steel, Cabinet painted pale grey RAL 7035. Steel door, and glass door trims painted dusty grey RAL 7037. KEY LOCK SWING HANDLE 6
NETWORKING - WALL MOUNT APPLICATIONS IMRAK 400 300MM DEEP SINGLE SECTION Ordering Information IMRAK 400 400MM DEEP TWO SECTION Ordering Information Height Door Single section (300mm) Single section (300mm) with key lock with swing handle 6U Glass 801-138103C 801-138119K 6U Metal 801-138104A 801-138120C 9U Glass 801-138107F 801-138123H 9U Metal 801-138108D 801-138124F 12U Glass 801-138111D 801-138127L 12U Metal 801-138112B 801-138128J 15U Glass 801-138115G 801-138131J 15U Metal 801-138116E 801-138132G Height Door Two section, key locks Two section, swing handle (300mm front + 100mm rear) (300mm front + 100mm rear) 6U Glass 801-138101G 801-138117C 6U Metal 801-138102E 801-138118A 9U Glass 801-138105K 801-138121A 9U Metal 801-138106H 801-138122K 12U Glass 801-138109B 801-138125D 12U Metal 801-138110F 801-138126B 15U Glass 801-138113L 801-138129G 15U Metal 801-138114J 801-138130L IMRAK 400 400MM DEEP SINGLE SECTION Ordering Information Height Door Single section (400mm) Single section (400mm) with key lock with swing handle 6U Glass 801-241784H 801-137103H 6U Metal 801-241785F 801-137104F 9U Glass 801-231181L 801-137107L 9U Metal 801-231182J 801-137108J 12U Glass 801-231191H 801-137111J 12U Metal 801-231192F 801-137112G 15U Glass 801-231201J 801-137115A 15U Metal 801-231202G 801-137116K IMRAK 400 500MM DEEP TWO SECTION Ordering Information Height Door Two section, key lock Two section, swing handle (400mm front +100mm rear) (400mm front +100mm rear) 6U Glass 801-241782A 801-137101A 6U Metal 801-241194G 801-137102K 9U Glass 801-231178L 801-137105D 9U Metal 801-231179J 801-137106B 12U Glass 801-231187K 801-137109G 12U Metal 801-231188H 801-137110L 15U Glass 801-231198E 801-137113E 15U Metal 801-231199C 801-137114C GENERAL ACCESSORIES Ordering Information Cable entry brush 801-10016H Earth kit (1 per section) 801-231543C UK 5 way switched power strip 640-912635C 19" brkt to recess power strip 640-912732E 19" brkt to protude power strip 801-246724A 255mm deep cantilever shelf 802-562284D Cantilever chassis supports 802-563106A 256mm chassis tray to fit supports 802-561013G Replacement gland plates and panel mount angles are available SWING HANDLE LOCKS The locks for the swing handle need to be ordered separately. Keyed alike lock - self locking All the locks supplied operate with the same key and the door automatically locks when closed. Keyed alike lock - manual locking All the locks supplied operate with the same key. To lock the door the key must be turned. Triangular key drive lock - self locking The lock is operated by a triangular machine cabinet drive. The door automatically locks when closed. Lock blank The lock blank fills the hole in the swing handle when a lock is not required. It also acts as a spring clip holding the handle into its housing. Keyed alike lock-self locking 802-563532F Keyed alike lock-manual locking 802-563610A Triangular key drive lock 802-563533D Lock blank 802-563534B 7
NETWORKING - WALL MOUNT APPLICATIONS IMRAK 600 WALL MOUNTING 12U, 17U, 22U x 19" cabinet in 600mm depth FEATURES Supplied fully configured for quick installation - select the items you need and we will assemble Available with toughened glass or metal door 3 heights options - 12U (635mm o/all), 17U (855mm o/all) 22U (1075mm o/all) All cabinets are industry standard 600mm wide and 600mm deep Optional earth bonding facility Shelving accessories available for modems etc Colour matched for coordinated installations Cable entry positions in top and bottom of all sections Load rating of 100kgs Supplied with drill template for wall Choice of colour ident on glass (standard is green) Available with either standard key locks or swing handles for additional security Choice of locks for swing handle MAIN BODY (WALL MOUNT) Welded construction made from 1.2mm zintec painted pale grey RAL 7035. Height 12U 844-259859G 17U 844-259860L 22U 844-259861J COVER TRIM KIT The cover trims provide attractive styling for the front of the cabinet when no door option has been selected. Cover trim : 1.2mm zintec painted dusty grey RAL 7037 including green feature trim. SWING HANDLE LOCKS The locks for the swing handle need to be ordered separately. Keyed alike lock - self locking All the locks supplied operate with the same key and the door automatically locks when closed. Keyed alike lock - manual locking All the locks supplied operate with the same key. To lock the door the key must be turned. Triangular key drive lock - self locking The lock is operated by a triangular machine cabinet drive. The door automatically locks when closed. Lock blank The lock blank fills the hole in the swing handle when a lock is not required. It also acts as a spring clip holding the handle into its housing. Height 12U 844-244653C 17U 844-244654A 22U 844-244655K Keyed alike lock-self locking 802-563532F Keyed alike lock-manual locking 802-563610A DOORS Triangular key drive lock 802-563533D Metal door : 1.2mm zintec painted Lock blank 802-563534B dusty grey RAL 7037 Glass door : 4mm toughened safety glass Height Door Std key lock Swing handle 12U Glass 844-244645B 844-137201C 12U Metal 844-244641K 844-137202A 17U Glass 844-244646L 844-137203K 17U Metal 844-244642H 844-137204H 22U Glass 844-244647J 844-137205F 22U Metal 844-244643F 844-137206D 5U INFILL PANELS The 5U infill panels are available as vented & non vented alternatives & allow for cable entry or convection cooling. When selected, the relevant door must be reduced by 5U. Infill panels : 0.9mm zintec painted dusty grey RAL 7037 5U FAN INFILL PANEL Vented Non vented 844-247849D 844-247848F The 5U fan infill panel is used in conjunction with doors to provide forced cooling for the cabinet. The panel is available for induction extraction. Each panel comprises three 120mm x 120mm fans (Part number 28-238116F) supplied fully wired to a CEE 22 connector & tested for immediate use. Induction Extraction Fan infill panel 844-247852D 844-247850H These infill panels will fit a 17U cabinet using a 12U door and a 22U cabinet using a 17U door. 8
NETWORKING - WALL MOUNT APPLICATIONS PANEL MOUNTING ANGLE SUPPORTS Unique to the IMRAK 600, they permit the panel mounting angles to be adjusted the full depth of the cabinet. The first & fourth hole at the front & rear of the support is tapped to allow simple panel mounting angle installation. Supplied as a pair with appropriate fixings. (When 4 panel mounting angles are required to be adjusted, two pairs of supports must be ordered). Panel mounting : 1.6mm zintec angle supports painted pale grey RAL 7035. Panel mount support kit 844-244661D CHASSIS SUPPORTS They can be varied along the depth of the cabinet & are prepunched to allow the fitting of chassis trays without further drilling. Supplied in pairs. Actual length Chassis support 270mm 802-561009J Chassis support 370mm 802-561561J Chassis support 470mm 802-561010B CHASSIS TRAYS The chassis trays feature slots providing for even airflow through the cabinet & as a basis to anchor components & accessories. They MUST be ordered with a pair of chassis supports (one kit). Chassis trays : 1.6mm steel zinc & colour passivated finish. Actual length Chassis tray 256mm 802-561013G Chassis tray 356mm 802-561014E Chassis tray 456mm 802-561015C CANTILEVER SHELVES These unique cantilever shelves fix onto the verticals via bayonet tabs & are retained via the plastic clips supplied. They provide an economic way of shelving without the need for panel mount angles. Cantilever shelf : 1.6mm steel painted pale grey RAL 7035. Depth Load rating 2U shelf 255mm 20kg 844-247854L 3U shelf 400mm 20kg 844-247855J EARTH CONTINUITY KIT Each kit contains 10 leads to earth all panels, doors & leaving extra leads to earth parts of the electronic equipment. Kit has ring terminals at both ends. Earth kit 802-560005L HEAVY DUTY PANEL MOUNTING ANGLES The heavy duty panel mounts (supplied in pairs) can be mounted directly to the vertical of the cabinet or to panel mount supports, permitting infinite depth adjustment. They also feature an addition flange for the mounting of accessories etc. Height 12U 802-560498F 17U 802-560503F 22U 802-560508G FIXED PANEL MOUNTING ANGLES The fixed panel mounts (supplied in pairs) provide a lower cost alternative to the heavy duty panel mounts. They can be fixed directly to the vertical of the cabinet or can be adjusted the depth of the rack at 20mm increments when used in conjunction with panel mounting angle support kits. Panel mounts : 2.0mm zintec painted pale grey RAL 7035 Height 12U 802-562367L 17U 802-562372G 22U 802-562377H DIRECT MOUNT SHELF Designed to provide maximum shelf support in the minimum configuration, this shelf uses the same bayonet tabs as mentioned above and secures into the 4 corners of the main body. Direct mount shelf : 1.2mm steel zinc & colour pasivate finish Load rating 50kgs Direct mount shelf 844-258356E OTHER ACCESSORIES Please refer to the following pages for details of Power Strips... 55-56 Cable Management... 51 9
NETWORKING - FREE STANDING INTRODUCTION VERO has developed a range of products suitable for floor standing your Networking application. These products include the award winning IMRAK 1400 major range of Networking floor mount cabinets. The products detailed in this section start with an open frame racking solution and progress through to a 42U EMC cabinet. All the products are designed to the very highest standards and through controlled Industrial Design, ensure that whatever combination is used, your installation will look professional, attractive and well managed. In any network often the first item you see is the network housings. VERO's products are designed to be sympathetic to any environment. All VERO products are designed to be flexible and delivered to your requirements. There is a full range of accessories available, that can be supplied with the cabinets, to ensure your on site installation time is kept to a minimum. COMMSRAK IMRAK 600 PRODUCTS AVAILABLE COMMSRAK - 12U, 37U, 42U x 19 open frame rack with integral cable management IMRAK 600-12U, 17U, 22U, 27U x 19 cabinet in 600mm depth IMRAK 1400 - VERAK IP - 12-47U 19" cabinet 600 & 800mm width x depth combinations 27U - 42U 19" cabinet 600 x 800mm width x depth combinations VERAK EMC - 27U - 42U 19" cabinet 600 x 800mm width x depth combinations IMRAK 1400 VERAK IP VERAK EMC 10
NETWORKING - FREE STANDING COMMSRAK 12U, 37U, 42U x19" openframe rack with integral cable managment FEATURES All round accessability Integral cable management Colour matched for coordinated installations Supplied flat pack with single type fixings and tooling Optional earth bonding facility Shelving accessories available for modems etc Industry standard 600mm x 600mm footprint Load rating up to 150kgs subject to shelf configuration Steel painted pale grey RAL 7035 Ordering Information Order Code 12U frame 52-255052B 37U frame 52-255051E 42U frame 52-255050H Floor mount kit 52-255053K Baying kit 52-244931C Top cover 450mm 52-248074K Earth kit 52-248075G Light/medium castor (2 braked/2 unbraked) 802-560002F Light/medium castor (4 unbraked) 802-561557L Adjustable feet 802-560001H Cantilever chassis support 802-563106A Chassis tray 256mm 802-561013G 255mm cantilever shelf 802-562284D 42U FLOOR MOUNT TOP COVER CANTILEVER CHASSIS SUPPORTS 11
NETWORKING - FREE STANDING CABINET IMRAK 600 CABINETS 12U, 17U, 22U, 27U x 19" cabinet in 600 depth FEATURES Supplied fully configured for quick installation - select the items you need and we will assemble Available with toughened glass or metal door 4 heights options - 12U (660mm o/all) 17U (880mm o/all) 22U (1100mm o/all) 27U (1320mm o/all) All cabinets are industry standard 600mm wide and 600mm deep Optional earth bonding facility Shelving accessories available for modems etc Colour matched for coordinated installations Cable entry position in base of cabinet Choice of colour ident on glass (standard is green) Available with either standard key locks or swing handles for additional security Choice of locks for swing handle 12 MAIN BODY The welded construction of the main body comprises a top, side panels & bottom panel. The bottom panel has an aperture for the provision of cabling. Welded construction made from 1.2mm zintec painted pale grey RAL 7035. Height 12U 844-244637A 17U 844-244638K 22U 844-244639H 27U 844-253265L DOORS Doors are available as glass or metal alternatives. They can be used in conjunction with a rear panel or with the 5U infill panels. Metal door : 1.2mm zintec painted dusty grey RAL 7037 Glass door : 4mm toughened safety glass Height Door Std key lock Swing handle 12U Glass 844-244645B 844-137201C 12U Metal 844-244641K 844-137202A 17U Glass 844-244646L 844-137203K 17U Metal 844-244642H 844-137204H 22U Glass 844-244647J 844-137205F 22U Metal 844-244643F 844-137206D 27U Glass 844-253283J 844-137207B 27U Metal 844-253272C 844-137208L SWING HANDLE LOCKS The locks for the swing handle need to be ordered separately. Keyed alike lock - self locking All the locks supplied operate with the same key and the door automatically locks when closed. Keyed alike lock - manual locking All the locks supplied operate with the same key. To lock the door the key must be turned. Triangular key drive lock - self locking The lock is operated by a triangular machine cabinet drive. The door automatically locks when closed. Lock blank The lock blank fills the hole in the swing handle when a lock is not required. It also acts as a spring clip holding the handle into its housing. Keyed alike lock-self locking 802-563532F Keyed alike lock-manual locking 802-563610A Triangular key drive lock 802-563533D Lock blank 802-563534B
NETWORKING - FREE STANDING CABINET FEATURE REAR PANELS The feature rear panel provides an attractive alternative to the metal door where access to the rear of the cabinet is not required. In addition to the rear panel, each kit contains 4 screws, 4 cage nuts & 4 plastic feature plugs. Rear panels : 0.9mm zintec painted dusty grey RAL 7037 Height 12U 844-244649E 17U 844-244650J 22U 844-244651G 27U 844-253310K COVER TRIM KIT The cover trims provide attractive styling for the front or rear of the cabinet when no door option has been selected. Cover trim : 1.2mm zintec painted dusty grey RAL 7037 including jade green feature trim. Height 12U 844-244653C 17U 844-244654A 22U 844-244655K 27U 844-253316J 5U INFILL PANELS The 5U infill panels are available as vented & non vented alternatives & allow for cable entry or convection cooling. When selected, the relevant door or rear panel must be reduced by 5U. For example, if cabling was required at the rear of a 22U cabinet, a 17U door or rear panel & a 5U infill panel would be selected. Infill panels : 0.9mm zintec painted dusty grey RAL 7037 Vented Non vented 844-247849D 844-247848F 5U FAN INFILL PANEL The 5U fan infill panel is used in conjunction with doors & rear panels to provide forced cooling for the cabinet. The panel is available for induction extraction. Each panel comprises three 120mm x 120mm fans (Part number 28-238116F) supplied fully wired to a CEE 22 connector & tested for immediate use. Induction Extraction Fan infill panel 844-247852D 844-247850H GLAND PLATE The gland plate can be selected to seal off the cable aperture in the bottom cover. Both full & half gland plates are available. The half gland plates allow a cable entry kit to be fitted in the centre section. The cable entry kit consists of two brushes through which cables may be pushed. Full gland plate : 2.0mm zintec with a zinc plated & passivated finish Half gland plate : 1.6mm zintec with a zinc plated & passivated finish Full gland plate 802-560945G Half gland plate 802-560953H Cable entry kit 802-561007B NOTE: If half gland plates are used without a cable entry kit, the slot remaining between the plates is 360 x 72mm. PANEL MOUNTING ANGLE SUPPORTS Unique to the IMRAK 600, they permit the panel mounting angles to be adjusted the full depth of the cabinet. The first & fourth hole at the front & rear of the support is tapped to allow simple panel mounting angle installation. Supplied as a pair with appropriate fixings. (When 4 panel mounting angles are required to be adjusted, two pairs of supports must be ordered). Panel mounting angle supports : 1.6mm zintec painted pale grey RAL 7035. Panel mount support kit 844-244661D HEAVY DUTY PANEL MOUNTING ANGLES The heavy duty panel mounts (supplied in pairs) can be mounted directly to the vertical of the cabinet or to panel mount supports, permitting infinite depth adjustment. They also feature an addition flange for the mounting of accessories etc. Height 12U 802-560498F 17U 802-560503F 22U 802-560508G 27U 802-560513C FIXED PANEL MOUNTING ANGLES The fixed panel mounts (supplied in pairs) provide a lower cost alternative to the heavy duty panel mounts. They can be fixed directly to the vertical of the cabinet or can be adjusted the depth of the rack at 20mm increments when used in conjunction with panel mounting angle support kits. Panel mounts : 2.0mm zintec painted pale grey RAL 7035 Height 12U 802-562367L 17U 802-562372G 22U 802-562377H 27U 802-562382D 13
NETWORKING - FREE STANDING CABINET OTHER ACCESSORIES Please refer to the following pages for details of Power Strips... Page 55-56 Cable Management... Page 51 LIGHT/MEDIUM DUTY CASTORS Supplied as a kit of four, they provide a static load rating of 65kg each. Castors 802-560002F CHASSIS SUPPORTS They can be varied along the depth of the cabinet & are prepunched to allow the fitting of chassis trays without further drilling. Supplied in pairs. Actual length Chassis support 270mm 802-561009J Chassis support 370mm 802-561561J Chassis support 470mm 802-561010B ADJUSTABLE FEET The adjustable feet allow the alignment of the cabinet on uneven surfaces. Supplied as a kit of four. Adjustable feet 802-560001H CANTILEVER SHELVES These unique cantilever shelves fix onto the verticals via bayonet tabs & are retained via the plastic clips supplied. This permits the use of the fixed 19" panel mounting angles in front of the shelf. They are available in 2 & 3U heights. Cantilever shelf : 1.6mm steel painted pale grey RAL 7035. Depth Load rating 2U shelf 255mm 20kg 844-247854L 3U shelf 400mm 20kg 844-247855J EARTH CONTINUITY KIT Each kit contains 10 leads to earth all panels, doors & leaving extra leads to earth parts of the electronic equipment. Kit has ring terminals at both ends. Earth kit 802-560005L CHASSIS TRAYS The chassis trays feature slots providing for even airflow through the cabinet & as a basis to anchor components & accessories. These MUST be ordered with a pair of chassis supports (one kit). Chassis trays : 1.6mm steel zinc & clear passivated finish. Actual length Chassis tray 256mm 802-561013G Chassis tray 356mm 802-561014E Chassis tray 456mm 802-561015C DIRECT MOUNT SHELF Designed to provide maximum shelf support in the minimum configuration and secures into the 4 corners of the main body. Direct mount shelf : 1.2mm steel zinc & colour pasivate finish Load rating 50kgs Direct mount shelf 844-258356E 14
IMRAK 1400 CABINETS IMRAK 1400, FRAME& CLADDING Open frame... 20 Steel door... 22 Glass door... 22 Cover trim... 23 Rear panel... 22 Ventilated infill panel... 24 Unventilated infill panel... 24 Side panel... 24 Top cover, unventilated... 25 Top cover, high top side vented... 25 Top cover, high top fully ventilated... 25 Top cover, with gland plate... 25 600MM PANEL MOUNTING SYSTEMS & SUPPORTS Panel mounting angles... 42 Simple panel mounting angles... 42 Panel mounting angle supports... 43 Reducing cable channel... 43 Cross members... 43 800MM 17
CABINETS CASTORS, PLINTHS, GLAND PLATES, FANS & POWER Page IMRAK 1400 Fan tray... 49 Power distribution panel (P.D.P.'s)... 55 Full gland plate IMRAK 1400... 26 Half gland plate (pair)... 26 Cable entry kit - used with the 'Half gland plate'... 26 Heavy duty castors... 27 Light/ medium duty castors... 27 Adjustable feet... 27 Plinth corner sections... 28 Plinth side trims... 28 Plinth front & rear trims... 28 SHELVING & CABLE MANAGEMENT Chassis supports - mount onto either 'panel mounting angles' or 'panel mounting angle supports'... 44 Chassis tray - mount onto chassis supports... 44 Chassis trays to fix directly to Vertical members... 45 Hook-in cantilever shelf... 44 19" Cantilever shelves... 45 Cantilever chassis support... 45 Sliding shelves - shelves and slides need to be ordered separately... 46 Cable trays... 51 Cable hoops... 51 18
IMRAK 1400 DIMENSIONS CABINETS Height DIM A DIM B 12U 620,1 533,4 17U 842,4 755,7 22U 1064,6 977,9 27U 1286,9 1200,2 32U 1509,1 1422,4 37U 1731,4 1644,7 42U 1953,6 1866,9 47U 2175,9 2089,2 A B DIM C Heavy duty castor 92,1mm Light duty castor 66,0mm Light duty braked castor 66,0mm Adjustable feet Min. 25 Max. 40 High top and high Add 24mm top side vented Adjustable Add 56mm foot adaptor to adjustable feet C 19,2 STANDARDS IEC 297-2 DIN 41494, part 7 DIN 41491, part 1 (mounting dimensions) EN 60950 VDE 0100 325 525 725 595, 795 /, 1195 488,1 688,1 LIFTING EYE CENTRES (12MM) 471,6 671,6 871,6 52,2 60 Corner verticals : 1,6mm steel End frames : 1,6mm steel Panel mounts : 2,0mm steel Panel mount supports : 1,6mm steel Side panels, door : 0,9mm steel and top panels IP glazed door : 1,2mm steel Electrical mounting panel : 2,5mm steel IMRAK load rating : 500kg COLOUR SPECIFICATION Powder epoxy paint. Side panels, framework : Pale grey, panel mounts, RAL 7035 horizontal and vertical trim kit Door, top panel : Dusty grey, and rear panel, RAL 7037 edge cover trims CUSTOMISING OPTIONS FRAME O/ALL 400 600 800 570.2 / 770.2 587.2 / 787.2 467 451 97,9 240 440 640 451 OR 651 465.3 OR 665.3 490 OR 690 IMRAK has been designed for quick and easy modification to suit specific applications or corporate identity requirements. We can, for instance, customise IMRAK to maximise your cable management efficiency. Special sizes and alternative finishes can also be supplied, subject to economic minimum quantity. The following customising options are available for IMRAK: Width Depth Punching/Drilling Screen printing Colour changes Wiring Cooling 19
CABINETS IMRAK 1400 FOR OFFICE AND COMPUTER ROOM ENVIRONMENTS WHATEVER FEATURES YOUR APPLICATION REQUIRES IMRAK was designed to be both flexible and affordable. When you place your order, you get (and pay for) only as many features as you need for your application. To make it easy for you, IMRAK is offered in two basic configurations - the OPEN FRAME unit and the READY RACK. One of these units may be sufficient for your application. If not, choose from the extensive range of IMRAK accessories to build the system you require. Remember to specify accessories such as tops, castors etc when placing your order. IMRAK 1400, if fitted with a non-vented top cover, has an IP23 rating. CONTENTS OF KIT A. The OPEN FRAME unit comprises: 4 verticals 2 end frames Fixings B. The READY RACK unit comprises: 4 verticals 2 end frames 2 side panels 2 panel mounts (order extra as required) 4 panel mounting supports* 2 reducing cable channels (800 wide racks only) Fixings * 6 panel mounting supports on units 42U & 47U AN EXTENSIVE RANGE OF STANDARD SIZES IMRAK is available in heights from 12U, rising in 5U increments, to 47U. Standard IEC 297-2 sizes of 400mm, 600mm and 800mm deep are available to accommodate various applications including 19" and PDS (Premises Distribution System). IMRAK 1400 COMPONENTS IN AN OPEN FRAME RACK. BUILDING YOUR OWN SYSTEM To specify your own system, simply choose an Open Frame or Ready Rack and add to it from piece part packs. You will then be given an unique order code which will enable you to re-order an identical unit at any time in the future. EXAMPLES 1. For a 37U 600mm wide x 600mm deep rack with front and rear metal doors, 2 panel mounts, top fan tray, ventilated top and light duty castors, order: 1 off 804-510101G Ready Rack 2 off 802-563394C Metal door 1 off 802-560475G Top fan tray 1 off 802-560647D Fully ventilated top 1 off 802-561557L Light/medium duty braked castors 2. 42U 800mm wide x 600mm deep rack with rear metal panel, glass front door, side panels, unventilated top and swing frame, order: 1 off 804-550305L Open Frame 1 off 802-560403K Side panels 1 off 802-560251G Rear metal panel 1 off 802-563460E Glass door 1 off 802-560471D Unventilated top 1 off 802-560584B Swing frame (full height) COMPONENTS IN A READY RACK. 20
IMRAK 1400 IMRAK 1400 (non-ip) Stock heights available of 600mm and 800mm wide on a 7 working day delivery. Non-stock heights available on 3 week delivery. or Special Order. CABINETS Dimensions Height (U) W x D Open Frame Ready Rack Metal door Glass door Rear panel Cover trim 600 x 600 804-550001J 804-510001L 802-563389G 802-563446K 802-560190A 802-560600H 600 x 800 804-550002G 804-510002J 802-563389G 802-563446K 802-560190A 802-560600H 12 800 x 600 804-550185F 804-510561F 802-563397H 802-563454L 802-560191K 802-560600H 800 x 800 804-550186D 804-510562D 802-563397H 802-563454L 802-560191K 802-560600H 600 x 600 804-550021C 804-510021E 802-563390L 802-563447H 802-560200B 802-560605J 600 x 800 804-550022A 804-510022C 802-563390L 802-563447H 820-560200B 802-560605J 17 800 x 600 804-550205D 804-510565J 802-563398F 802-563455J 802-560201L 802-560605J 800 x 800 804-550206B 804-510566G 802-563398F 802-563455J 802-560201L 802-560605J 600 x 600 804-550041H 804-510041K 802-563391J 802-563448F 802-560210K 802-560610E 600 x 800 804-550042F 804-510042H 802-563391J 802-563448F 802-560210K 802-560610E 22 800 x 600 804-550225J 804-510569A 802-563399D 802-563456G 802-560211H 802-560610E 800 x 800 804-550226G 804-510570E 802-563399D 802-563456G 802-560211H 802-560610E 600 x 400 804-550060D 804-510060F 802-563392G 802-563449D 802-560220G 802-560615F 600 x 600 804-550061B 804-510061D 802-563392G 802-563449D 802-560220G 802-560615F 27 600 x 800 804-550062L 804-510062B 802-563392G 802-563449D 802-560220G 802-560615F 800 x 400 804-550244E 804-510572A 802-563400A 802-563457E 802-560221E 802-560615F 800 x 600 804-550245C 804-510573K 802-563400A 802-563457E 802-560221E 802-560615F 800 x 800 804-550246A 804-510574H 802-563400A 802-563457E 802-560221E 802-560615F 600 x 600 804-550081G 804-510081J 802-563393E 802-563450H 802-560230D 802-560620B 32 600 x 800 804-550082E 804-510082G 802-563393E 802-563450H 802-560230D 802-560820B 800 x 600 804-550265H 804-510577B 802-563401K 802-563458C 802-560231B 802-560620B 800 x 800 804-550266F 804-510578L 802-563401K 802-563458C 802-560231B 802-560620B 600 x 400 804-550100G 804-510100J 802-563394C 802-563451F 802-560240A 802-560625C 600 x 600 804-550101E 804-510101G 802-563394C 802-563451F 802-560240A 802-560625C 37 600 x 800 804-550102C 804-510102E 802-563394C 802-563451F 802-560240A 802-560625C 800 x 400 804-550284D 804-510580B 802-563402H 802-563459A 802-560241K 802-560625C 800 x 600 804-550285B 804-510581L 802-563402H 802-563459A 802-560241K 802-560625C 800 x 800 804-550286L 804-510582J 802-563402H 802-563459A 802-560241K 802-560625C 600 x 400 804-550120A 804-510120C 802-563395A 802-563452D 802-560250J 802-560630K 600 x 600 804-550121K 804-510121A 802-563395A 802-563452D 802-560250J 802-560630K 600 x 800 804-550122H 804-510122K 802-563395A 802-563452D 802-560250J 802-560630K 42 600 x 900 804-550123F 804-510123H 802-563395A 802-563452D 802-560250J 802-560630K 800 x 400 804-550304B 804-510584E 802-563403F 802-563460E 802-560251G 802-560630K 800 x 600 804-550305L 804-510585C 802-563403F 802-563460E 802-560251G 802-560630K 800 x 800 804-550306J 804-510586A 802-563403F 802-563460E 802-560251G 802-560630K 600 x 600 804-550141D 804-510141F 802-563396K 802-563453B 802-560260F 802-560635L 600 x 800 804-550142B 804-510142D 802-563396K 802-563453B 802-560260F 802-560635L 47 600 x 900 804-550143L 804-510143B 802-563396K 802-563453B 802-560260F 802-560635L 800 x 600 804-550325E 804-510589F 802-563404D 802-563461C 802-560261D 802-560635L 800 x 800 804-550326C 804-510590K 802-563404D 802-563461C 802-560261D 802-560635L 21
CABINETS FRONT AND REAR DOORS AND PANELS IMRAK 1400 Doors suitable for the front or rear of IMRAK are available in metal and glass. Shortened doors can also be fitted to provide space above or below the door for accommodating fan units, grills, touch panels or cable entries. Shortened door infill panels are available with or without ventilation. Unventilated rear panels are also offered in all standard widths and U heights, and may be used as cable gland panels. AND CONTENTS OF KITS Cover trim : Aluminium extrusion Painted in RAL 7037. Metal door Glass door : 0,9mm steel complete with brackets, fixings, lock and 2 keys. Painted in RAL 7037. : 4mm toughened tinted grey glass (6mm for 42U & 47U doors 800 wide), complete with brackets, fixings, door lock and keys. PLAIN RACK IMRAK WITH COVER TRIM Shortened door infill panels : 0,9mm steel complete with brackets and fixings. Painted in RAL 7037. Rear panel : 0.9mm steel complete with brackets and fixings. Painted in RAL 7037. Swing handle : Swing handle suitable for the IMRAK 1400 steel or glass doors. DOORS, IMRAK 1400 STEEL DOOR Height Metal door Glass door U 600mm wide 800m wide 600mm wide 800mm wide 12 802-563389G 802-563397H 802-563446K 802-563454L 17 802-563390L 802-563398F 802-563447H 802-563455J 22 802-563391J 802-563399D 802-563448F 802-563456G 27 802-563392G 802-563400A 802-563449D 802-563457E 32 802-563393E 802-563401K 802-563450H 802-563458C 37 802-563394C 802-563402H 802-563451F 802-563459A 42 802-563395A 802-563403F 802-563452D 802-563460E 47 802-563396K 802-563404D 802-563453B 802-563461C PANELS AND TRIMS, IMRAK 1400 Height Rear panel Cover trim U 600mm wide 800mm wide 600/800 wide 12 802-560190A 802-560191K 802-560600H 17 802-560200B 802-560201L 802-560605J 22 802-560210K 802-560211H 802-560610E 27 802-560220G 802-560221E 802-560615F 32 802-560230D 802-560231B 802-560620B 37 802-560240A 802-560241K 802-560625C 42 802-560250J 802-560251G 802-560630K 47 802-560260F 802-560261D 802-560635L 22 REAR PANEL STANDARD GLASS FRONT DOOR
IMRAK 1400 CABINETS FITMENT OF COVER TRIM COVER TRIMS For applications where no doors are required, a set of aluminium trims may be fitted. Cover trims are supplied in pairs painted in RAL 7037 and with an inset green plastic coach line. See previous page for ordering information. As an option, red or blue coach lines may be specified at extra cost. see below for details. Note: These trims cannot be fitted at the same time as a door. COACH LINES A green plastic coach line is fitted to the 'cover trims' and, 'glass door' as a standard free of charge high-light colour. Alternative colours or extra green coach lines may be specified for an additional cost. Colour Length Green 2 x 2.15m 802-562230E Red 2 x 2.15m 802-562232A Blue 2 x 2.15m 802-562231C IMRAK 1400 DOOR SWITCH Designed to facilitate door access monitoring. The microswitch is a fully sealed unit with 500mm integral leads potted onto the terminal. The switch comes complete with its own mounting plate and fixings to attach it to an IMRAK 1400 vertical. Microswitch specification: Contact rating:5a 250V ac,3a 28V dc Contact resistance:50mh Operating temperature:-40 c to +125 c Note: the unit is recommended for low voltage applications ONLY. This is due to the vulnerability of the single insulating cable within the rack. IMRAK door switch 802-557460B EARTHING KIT FOR GLASS DOOR This earthing kit electrically joins the lock member to the hinge member on the glass door via a conductive self adhesive tape. For full rack earthing an 'Earth Continuity Kit' is required. 600mm wide 802-563520B 800mm wide 802-563521L SWING HANDLE PLUS LOCK OPTION SWING HANDLES Both the metal and glass doors can have a swing handle fitted as an option. Please note, the locks for the swing handle need to be ordered separately. Keyed alike lock - self locking All locks supplied operate with the same key and the door automatically locks when closed. Keyed alike lock - manual locking All locks supplied operate with the same key. To lock the door the key must be turned. Triangular key drive lock - self locking The lock is operated by a triangular machine cabinet drive. The door automatically locks when closed. Lock blank The lock blank fills the hole in the swing handle when a lock is not required. It also acts as a spring clip holding the handle into its housing. Swing handle-imrak 1400 802-563494K Keyed alike lock-self locking 802-563532F Keyed alike lock-manual locking 802-563610A Triangular key drive lock 802-563533D Lock blank 802-563534B 23
CABINETS IMRAK 1400 UNVENTILATED INFILL PANEL VENTILATED INFILL PANEL INFILL PANELS (NON-IP) These panels have a nominal size of 5U. For example, a panel plus 32U door would fit a 37U rack. They may be fitted above or below (or both) either a door (glass or steel) or a rear panel. Typical uses are to allow mechanical handling of cables i.e. to accept connectors/cable glands, or bulk cable access using the cable brush version. 600mm wide unventilated 802-561042L 800mm wide unventilated 802-561043J 600mm wide ventilated 802-561044G 800mm wide ventilated 802-561045E 600mm wide with cable brush 802-563581D REDUCED HEIGHT DOOR WITH VENTILATED INFILL PANEL 3U INFILL PANEL 3U INFILL PANELS This panel has a nominal size of 3U and allows two standard doors to be fitted onto the same rack. For example a 42U high rack could have a 12U glass door on top and a 27U steel door on the bottom, the 3U infill panel filling the gap between the two. 3U INFILL PANEL 3U x 600mm 802-563383H SIDE PANELS, IMRAK 1400 Strong, lightweight side panels are easily fixed into position using smooth action slam latches. A centre grommet may be removed and replaced with a lock if required. Side panels are supplied in pairs and painted RAL 7035 with RAL 7037 mouldings. IMRAK 1400 SHOWING SLAM-LATCH FITTING SIDE PANELS IMRAK 1400 Non-stock heights available on Special Order. Height (U) 400mm deep 600mm deep 800mm deep 900mm deep 12-802-560283E 802-560284C - 17-802-560303C 802-560304A - 22-802-560323H 802-560324F - 27 802-560342D 802-560343B 802-560344L - 32 802-560363G 802-560364E - 37 802-560382C 802-560383A 802-560384K - 42 802-560402A 802-560403K 802-560404H 802-560405F 47-802-560423D 802-560424B 802-560425L SECTION SHOWING ''SLAM-LATCH'' APPLICATION A = Latch position B = Hook of side panel locating onto end frame SIDE PANEL LOCKS For lockable side panels, simply order a kit of two locks: 802-560004B 24
IMRAK 1400 CABINETS TOP COVERS UNVENTILATED HIGH TOP SIDE VENTED HIGH TOP FULLY VENTED TOP COVERS Three styles of top are available. The low unvented top provides no ventilation. The high top side vented allows air flow through side slots. The high top fully vented provides air flow through a matrix of square top holes as well as side slots. TOP COVERS Non-stock heights available on Special Order. Dimensions Unventilated High Top, High Top, (W x D) (sealed) Side Vented Fully Ventilated 600 x 400 802-560466H 802-560654G 802-560646F 600 x 600 802-560467F 802-560655E 802-560647D 600 x 800 802-560468D 802-560656C 802-560648B 600 x 900-802-560657A 802-560649L 800 x 400 802-560470F 802-560658K 802-560650D 800 x 600 802-560471D 802-560659H 802-560651B 800 x 800 802-560472B 802-560660A 802-560652L Note: High tops must be removed for lifting eyes to be fitted to the racks HIGH TOP, SIDE VENTED WITH GLAND PLATE This range of top covers are supplied complete with a removable gland plate. The gland plate is supported by an internal frame structure which transfers any loads applied to the cover directly onto the racks main frame. The gland plate allows cable glands to be fitted, and has an aperture of 360 x 190mm (W x D). The top cover allows air to flow out of slots in all four side edges of the top cover. HIGH TOP, SIDE VENTED WITH GLAND PLATE CONTENTS OF KIT 1 top cover 1 top gland plate Fixings Top cover : 0.9mm steel Gland plate : 1.6mm steel Finish : Painted in RAL 7037 Dimensions (W x D) 600 x 600 802-562982B 600 x 800 802-562983L 800 x 600 802-562985G 800 x 800 802-562986E 25
CABINETS GLAND PLATES IMRAK 1400 Gland plates are used to infill the space in the end frames or to allow cable glands to be fitted, or for supporting odd sized loads. Both full and half gland plates are available. The half gland plates allow a cable entry kit to be fitted in the centre section. The cable entry kit consists of two brushes through which cables may be pushed. CONTENTS OF KIT Full gland plate: 1 gland plate and fixings Half gland plate: 2 half sized gland plates and fixings GLAND PLATE Full gland plate, 2.0mm steel : Half gland plate, 1.6mm steel: zinc plate and passivate zinc plate and passivate FULL AND HALF GLAND PLATES GLAND PLATES AND CABLE ENTRY KITS 600mm wide 800mm wide 400mm deep 600mm deep 800mm deep 400mm deep 600mm deep 800mm deep Full gland plate 802-560945G 802-560946E 802-560947C 802-560949K 802-560950C 802-560951A Half gland plates 802-560953H 802-560954F 802-560955D 802-560957L 802-560958J 802-560959G Cable entry kit 802-561007B 802-561007B 802-561007B 802-561008L 802-561008L 802-561008L Note: If half gland plates are used without a cable entry kit the slot remaining between the plate is 360 x 72 on 600 wide racks and 560 x 72 on 800 wide racks. BAYING KIT The baying kit is designed for joining two IMRAKs side by side. CONTENTS OF KIT 4 brackets painted in RAL 7035 Fixings Note: Cage nuts should be fitted in the square hole of one rack. (See 1 in diagram and bracket fitted using 2 screws and nuts in the second rack before the racks are pushed together). Baying kit 802-560943L VERTICAL TRIM KIT A vertical trim kit is used to create a smooth, neat appearance when two racks are bayed together. Fitment is by means of attaching to one rack and allowing the other leg to float. CONTENTS OF KIT 2 trims (1 for front; 1 for rear) Fixings Height 12 802-560805A 17 802-560810H 22 802-560815J 27 802-560820E 32 802-560825F 37 802-560830B 42 802-560835C 47 802-560840K HORIZONTAL TRIM KIT A horizontal trim kit is used to complement the vertical trim kit and stop foreign bodies falling down the slot between the two racks. CONTENTS OF KIT 1 trim and fixings painted in RAL 7035 Rack depth 400 802-561046C 600 802-561047A 800 802-561048K Non-stock Special Order. 26
IMRAK 1400 CASTORS CABINETS Two types of castors are available. Light/medium duty: castors load max. 68Kg each, screwed direct into corner blocks, using 10mm threads also available as braked version. Heavy duty: castors load 115Kg each under average conditions, fitted to the rack with bolt on mounting plates. Available in braked and unbraked versions. Note: Adjustable feet cannot be used together with the light/ medium duty castor, as both use the same mounting hole. LIGHT/MEDIUM DUTY CASTOR LIGHT/MEDIUM DUTY BRAKED CASTOR CONTENTS OF KIT Unbraked castors are supplied as a kit of 4 castors. Braked castors are supplied as a kit with 2 braked and 2 unbraked. Heavy duty castors are supplied complete with mounting plates and fixings. ADJUSTABLE FEET These allow you to align your rack on uneven surfaces. Adjustable feet are screwed direct into corner blocks, using 10mm threads. An adaptor is required when feet are to be fitted as well as heavy duty castors. HEAVY DUTY CASTOR HEAVY DUTY BRAKED CASTOR Note: Adjustable feet cannot be used together with the light/ medium duty castors, as both use the same mounting hole. LIFTING EYE KIT Eyebolts can be screwed into the 12mm threaded holes in the top four corners of the IMRAK frame to facilitate lifting of fully loaded racks. Each eyebolt has a maximum loading capacity of 320Kg. Supplied as a kit of 4. Note: When using a rack with a high top, the top must be removed to fit the lifting eyes. BOLTING DOWN PLATE ADJUSTABLE FOOT ADJUSTABLE FOOT ADAPTOR This is a kit of 4 rectangular plates which allows the base frame to be bolted down, using 12mm bolts (not supplied). Painted in RAL 7035 ACCESSORIES Lifting eye kit 802-560000K Adjustable feet kit 802-560001H Adjustable feet adaptor 802-560944J Light/medium duty castor 802-561557L LIFTING EYEBOLT BOLTING DOWN PLATE Light/medium duty braked castor 802-560002F Heavy duty castor 802-560003D Heavy duty braked castor for IMRAK 1400 802-561556B Bolting down plate 802-562415D All accessories above are supplied in kits of 4 27
CABINETS PLINTH AND PLINTH TRIM KITS IMRAK 1400 Plinth kits are available in two heights 100mm or 200mm. Plinth kits consist of four identical corner sections and four infill sections which allow easy modification for cable entry. Adjustable feet which will align IMRAK on uneven surfaces can be fitted to a plinth. Plinths may be stacked to give additional heights. CONTENTS OF KIT 100mm/200mm plinths : 4 corner sections painted in RAL 7035 and fixings Side trims : 2 side trims painted in RAL 7035 and fixings 2 front or rear trims painted in RAL 7035 Note: All 3 items must be ordered to create a full plinth kit. PLINTHS - 100mm HIGH VERSION /Unit Size 600 x 400 600 x 600 600 x 800 800 x 400 800 x 600 800 x 800 100mm high plinth 802-561033A 802-561033A 802-561033A 802-561033A 802-561033A 802-561033A Plinth side trim kit 802-561034K 802-561035H 802-561036F 802-561034K 802-561035H 802-561036F Plinth front and rear trim kit 802-561038B 802-561038B 802-561038B 802-561039L 802-561039L 802-561039L PLINTHS - 200mm HIGH VERSION /Unit Size 600 x 400 600 x 600 600 x 800 800 x 400 800 x 600 800 x 800 200mm high plinth 802-563030H 802-563030H 802-563030H 802-563030H 802-563030H 802-563030H Plinth side trim kit 802-563031F 802-563032D 802-563033B 802-563031F 802-563032D 802-563033D Plinth front and rear trim kit 802-563034G 802-563034G 802-563034G 802-563035J 802-563035J 802-563035J EXTENSION PLINTH Extension plinths are designed to provide increased stability when using heavy equipment and are recommended for mobile racks fitted with 800mm glass doors or swing frames. Each plinth has fixing studs for heavy duty castors and threads fitted to take adjustable feet (castors and adjustable feet to be ordered separately). CONTENTS OF KIT 2 plinths plus fixings to fit to the rack (order castors and adjustable feet separately). EXTENSION PLINTHS /Unit Depth 400 deep 600 deep 800 deep Extension plinth 802-561029C 802-561030G 802-561031E 28 PLINTH LEVELLING KIT 100mm Levelling kit 802-552997F 200mm Levelling kit 802-563158D For full details see page 35
IMRAK 1400 CABINETS GLAZED DOORS METAL DOORS IMRAK 1400 1200MM WIDE This extended width IMRAK 1400 allows unrestricted access between the rack verticals. For networking applications this not only permits increased cable density compared with using two bayed 600mm wide racks. (5, 110 block towers instead of 4) but also removes the need to thread cable patch cords around the central verticals. The benefits are being able to divide one or both sides into 19" allowing the use of 110 block systems along with 19" items i.e. hubs, routers, modems etc. in the same cabinet. CONTENTS OF KIT A.The OPEN FRAME unit comprises 4 verticals 2 end frames Fixings B. The READY RACK unit comprises 4 verticals 2 end frames 2 side panels 1 top cover complete with gland plate 4 panel mounting supports* Fixings * 6 panel mounting supports on 42U racks FRONT AND REAR DOORS AND PANELS Double doors suitable for the front or rear of IMRAK 1400, 1200mm wide are available in metal and glass. A double rear panel option is also available. These double doors and rear panels lock onto a vertical central member. This central member is easily removed when installing equipment into the rack allowing full width access. AND CONTENTS OF KITS Double glazed doors:- 2 glazed doors, steel frame 1.2mm steel painted in RAL 7037, glazed with 4mm toughened tinted grey glass, complete with multipoint locking mechanism 1 vertical central member Brackets & fixings Double metal doors:- 2 steel doors, 0.9mm steel painted in RAL 7037, complete with multipoint locking mechanism 1 vertical central member Brackets & fixings Double rear panels:- 2 rear panels, 0.9mm steel painted in RAL 7037 1 vertical central member Brackets & fixings SWING HANDLES Both the metal and glass doors can have a swing handle fitted as an option. Please note, the locks for the swing handle need to be ordered separately. Keyed alike lock - self locking All the locks supplied operate with the same key and the door automatically locks when closed. Keyed alike lock - manual locking All the locks supplied operate with the same key. To lock the door the key must be turned. Triangular key drive lock - self locking The lock is operated by a triangular machine cabinet drive. The door automatically locks when closed. Lock blank The lock blank fills the hole in the swing handle when a lock is not required. It also acts as a spring clip holding the handle into its housing. Swing handle-for 1200mm wide 802-563494K Keyed alike lock-self locking 802-563532F Keyed alike lock-manual locking 802-563610A Triangular key drive lock 802-563533D Lock blank 802-563534B Dimensions Height (U) W x D Open Frame Ready-Rack Metal doors Glazed doors Rear panels 32U 1200 x 600 804-555081D 804-510455E 802-563512A 802-563516D 802-562859G 32U 1200 x 800 804-555082B 804-510456C 802-563512A 802-563516D 802-562859G 37U 1200 x 600 804-555101B 804-510475K 802-563513K 802-563517B 802-562864H 37U 1200 x 800 804-555102L 804-510476H 802-563513K 802-563517B 802-562864H 42U 1200 x 600 804-555121G 804-510495D 802-563514H 802-563518L 802-562869J 42U 1200 x 800 804-555122E 804-510496B 802-563514H 802-563518L 802-562869J For side panels see page 24. 29
CABINETS 19" PANEL MOUNTING SYSTEM FOR IMRAK 1400, 1200MM WIDE Full or partial 19" panel mounts can be installed into this rack. IMRAK 1400 FULL LENGTH 19" PANEL MOUNTING SYSTEM This is achieved by putting in one or two central verticals, which match the height of the rack, plus one or two pairs of panel mounting angles. Note: two verticals and two pairs of panel mounting angles are only required when 19" mounting is needed side by side within the 1200mm wide window. PARTIAL 19" PANEL MOUNTING SYSTEM For short sections of 19" mounting, a support cross bar is required and verticals and matching panel mounting angles of the required length. VERTICALS* Height 12U 802-562993H 17U 802-562998J 22U 802-563003L 27U 802-563008A 32U 802-563013H 37U 802-563018J 42U 802-563023E *Sold as single items 19" PANEL MOUNTING SYSTEM SUPPORT CROSS BAR 1200mm wide 802-563029D PARTIAL 19" PANEL MOUNTING SYSTEM 30
IMRAK 1400 CABINETS 110 TOWER UNIT FOR IMRAK 1400, 1200MM WIDE A modular tower unit has been developed for the mounting of 110 blocks and cable management blocks. The maximum number of towers that can be installed across the width of an IMRAK 1400, 1200mm wide, is 5 with additional cross members. However the towers can be back to back mounted allowing 10 towers to be mounted. The cross members mount from the panel mount supports. Remember to order 2 pairs of panel mount angle supports if working from an open frame. 110 TOWER SYSTEM Mild steel Painted grey RAL 7035 CONTENTS OF KITS Tower kit : 1 tower unit and fixings Cross member kit : 2 cross members and fixings Cable restrainers : 1 pair and fixings Cable trough kit : 1trough and fixings 12U Tower (200 Pair) 961-554476A 17U Tower (300 Pair) 961-554477K 22U Tower (500 Pair) 961-554478H 27U Tower (600 Pair) 961-554192D 32U Tower (800 Pair) 961-554193B 37U Tower (900 Pair) 961-554194L 42U Tower (1000 Pair) 961-554195J IMRAK 1400, 1200mm wide cross member 961-554199A Cable restrainers 961-554200J Cable trough 961-554525C Panel mounting angle supports 600 deep racks 802-560545A Panel mounting angle supports 800 deep racks 802-560546K 1200MM WIDE - HIGH TOP, SIDE VENTED WITH GLAND PLATE This top cover is supplied complete with two top gland plates. Ventilation is provided by allowing air to flow out of slots in all four sides of the top cover. CONTENTS OF KIT 1 high top side vented 2 top gland plates Fixings 1200 x 600 802-562978D 1200 x 800 802-562979B TOP COVER 31
CABINETS PLINTH AND PLINTH TRIM KITS FOR IMRAK 1400, 1200MM WIDE IMRAK 1400 Plinth kits are available in two heights 100mm or 200mm. The complete plinth consists of four identical corner sections, two central sections and six infill sections which allow easy modification for cable entry. Adjustable feet which will align IMRAK on uneven surfaces can be fitted to a plinth. Plinths may be stacked to give additional heights. CONTENTS OF KITS 100/200mm plinth : corners 100/200mm central: sections 4 corner sections painted in RAL 7035 and fixings 2 central sections painted in RAL 7035 and fixings Side trim kit : 2 side trims painted in RAL 7035 and fixings Front trim kit : 2 front trims painted in RAL 7035 and fixings Rear trim kit : 2 rear trims painted in RAL 7035 and fixings PLINTH AND PLINTH TRIM KITS Note: All 5 items must be ordered to create a full 1200mm wide plinth kit. /unit size 1200 x 600 1200 x 800 100mm high plinth corners 802-561033A 802-561033A 100mm high central section 802-563036G 802-563036G Plinth side trim kit 802-561035H 802-561036F Plinth front trim kit 802-561038B 802-561038B Plinth rear trim kit 802-561038B 802-561038B /unit size 1200 x 600 1200 x 800 200mm high plinth corners 802-563030H 802-563030H 200mm high central section 802-563037E 802-563037E Plinth side trim kit 802-563032D 802-563033B Plinth front trim kit 802-563034G 802-563034G Plinth rear trim kit 802-563034G 802-563034G PLINTH LEVELLING KIT When fitting a 100m or 200mm high plinth with adjustable feet, a stiffening kit is needed which consists of 4 spacers and fixings to pass the load from the lower flange to the frame of the rack and also M10 hexagon nuts to lock the adjustable foot in place. 100mm levelling kit 802-552997F 200mm levelling kit 802-563158D ADJUSTABLE FEET AND CASTORS Adjustable feet and castors are available for IMRAK 1400, 1200mm wide in a kit of 6, braked castors are supplied in kits of 3 braked and 3 unbraked. For further details see page 27. Adjustable feet kit 802-563042A Light/medium duty castor 802-563043K Light/medium duty braked castor 802-563044H Heavy duty castor 802-563045F Heavy duty braked castor 802-563046D Adjustable feet adaptor 802-563047B 32
CABINETS VERAK IP Features and Benefits NEW VERAK IP IP 55 sealed Protecting the system from dust, dirt, and water jets Thermal control A full range of thermal control options are available to cool your system within the sealed enclosure Robust cladding Protects the system in all shop-floor and industrial environments Heavy duty frame Allows fully loaded racks to be safely transported. The VERAK is capable of taking 750kg loads Supplied configured Racks delivered to site with all accessories fitted to the customer specification, thereby making installation quicker and easier Simple baying Racks can be linked together for larger applications quickly whilst maintaining the IP seal Accessories A full range of proven accessories are available to help with networking, electronic or electrical applications Styling A racking system with the appearance to complement the most advanced office, laboratory or manufacturing environment Range ex-stock Ex-stock sizes Other sizes available on application 27U 600x600mm 37U 600x600mm 37U 600x800mm 42U 600x600mm 42U 600x800mm 42U 800x600mm 42U 800x800mm Glass or metal door. IP 5 5 INDEX OF PROTECTION DUST PROTECTION 1st index 5 Limitation of ingress of dust Total protection of persons from touching voltage-carrying or internal moving parts.protection of the object from harmful deposit of dust. Although ingress is not completely prevented, dust will not enter in sufficient quantity to impair the operation or safety of the apparatus. WATER PROTECTION 2nd index 5 Protection against jet water A jet of water projected from a standard nozzle at 12.5 litres per minute against the object from all directions must not have any harmful effect. 34
NEW VERAK IP CABINETS D DIM RACK WIDTH BOLT DOWN HOLES H CENTRE LINE FOR FEET & BOLT DOWN HOLES APERTURE L J K FEET CENTRES RACK DEPTH E DIM F DIM WIDTH BETWEEN VERTICALS APERTURE H 97,9 467,0 WIDTH BETWEEN VERTICALS G DIMENSIONS Height DIM A DIM C 12U 535,0 645,0 17U 757,3 867,3 22U 979,5 1089,5 27U 1201,8 1311,8 32U 1424,0 1534,0 37U 1646,3 1756,3 42U 1868,5 1978,5 47U 2090,8 2200,8 Shaded areas = not stocked 4,2 STANDARD TOP COVER 451,0 465,3 30,0 VENTED TOP COVER Heavy duty castor High top and high top side vented 59,7mm Add 30mm 'A'DIMENSION = 'B' U HEIGHTS 'C'DIMENSION = TOTAL RACK HEIGHT 59,7 451,0 20,0 GLAND PLATE APERTURE STANDARDS IEC 287-2 Rack dimensions EN 60950 Earthing IEC 529 IP rating -IP55 Verticals : 2.0mm steel End frames : 2.0mm steel Sides, doors : 1.6mm steel Top covers : 1.2mm steel IP glass : 4.0mm toughened PAINT AND COLOUR SPECIFICATION Specification : Iron phosphate pre-treatment electropaint primer and textured powder top coat Colour : Frame, side panels, and internal mounting systems. Pale gray RAL7035 Doors and top covers anthracite grey RAL 7016 Rack Rack Bolt Rack dimensions 'A' DIM 'B' Units 'C' DIM 'D' DIM 'E' DIM 'F' DIM 'G' DIM 'H' DIM 'J' DIM 'K' DIM 'L' DIM 'M' DIM width depth holes feet aperture aperture 27U x 600 x 600 1201.8 27 1311.8 597.6 678.0 490.0 440.0 558.0 380.0 450.0 393.4 363.8 27U x 600 x 800 1201.8 27 1311.8 597.6 878.0 490.0 640.0 758.0 380.0 450.0 593.4 363.8 27U x 800 x 600 1201.8 27 1311.8 797.6 678.0 690.0 440.0 558.0 580.0 650.0 393.4 563.8 27U x 800 x 800 1201.8 27 1311.8 797.6 878.0 690.0 758.0 580.0 650.0 593.0 593.4 563.8 37U x 600 x 600 1646.3 37 1756.3 597.6 678.0 490.0 440.0 558.0 380.0 450.0 393.4 363.8 37U x 600 x 800 1646.3 37 1756.3 597.6 878.0 490.0 640.0 758.0 380.0 450.0 593.4 363.8 37U x 800 x 600 1646.3 37 1756.3 797.6 678.0 690.0 440.0 558.0 580.0 650.0 393.4 563.8 37U x 800 x 800 1646.3 37 1756.3 797.6 878.0 690.0 640.0 758.0 580.0 650.0 593.4 563.8 42U x 600 x 600 1868.5 42 1978.5 597.6 678.0 490.0 440.0 558.0 380.0 450.0 393.4 363.8 42U x 600 x 800 1868.5 42 1978.5 597.6 878.0 490.0 640.0 758.0 380.0 450.0 593.4 363.8 42U x 800 x 600 1868.5 42 1978.5 797.6 678.0 690.0 440.0 558.0 580.0 650.0 393.4 563.8 42U x 800 x 800 1868.5 42 1978.5 797.6 878.0 690.0 640.0 758.0 580.0 650.0 593.4 563.8 35
CABINETS MAIN STRUCTURE FRAME The frame comprises 4 verticals and 2 end frames DOORS FOR THE FRONT AND REAR OF THE RACK GLAZED DOOR 4mm toughened tinted glass complete with swing handle. The required lock or lock blank needs to be ordered separately. SWING HANDLES NEW VERAK IP Both the metal and glass doors have a swing handle fitted as standard. Please note, the locks for the swing handle need to be ordered separately. Keyed alike lock - self locking All the locks supplied operate with the same key and the door automatically locks when closed. Keyed alike lock - manual locking All the locks supplied operate with the same key. To lock the door the key must be turned. Triangular key drive lock - self locking The lock is operated by a triangular machine cabinet drive. The door automatically locks when closed. Lock blank The lock blank fills the hole in the swing handle when a lock is not required. It also acts as a spring clip holding the handle into its housing. Keyed alike lock-self locking 802-563532F Keyed alike lock-manual locking 802-563610A Triangular key drive lock 802-563533D Lock blank 802-563534B FOR THE TOP FOR THE SIDES TOP COVER IP 55 unvented top cover. For information on side vented and fully vented non IP top covers see page 25. STEEL DOORS 1.6mm steel door complete with swing handle. The required lock or lock blank needs to be ordered separately SIDE PANELS Side panels are sold in pairs and are 1.6mm steel painted in RAL7035. The side panels are fitted using captive pozi drive screws which allow the units to be easily fitted or removed. 36
NEW VERAK IP FOR THE SIDES CONTINUED FOR THE BOTTOM OF THE RACK CABLE & THERMAL MANAGEMENT CABINETS IP BAYING KIT The kit consists of the required length of selfadhesive IP gasket material and 6 brackets which lock the two racks together to form a bayed suite of racks. For example: If three racks are to be bayed together to make one suite of racks, one pair of side panels are required (to be used either end of the suite) and two baying bracket kits. IP55 GLAND PLATE Gland plates are used to IP55 seal the space in the end frame and to allow sealed cable glands to be fitted. A gland plate must be fitted to achieve the IP55 seal on the complete rack. REMEMBER TO ORDER YOUR PANEL MOUNTS For panel mounting systems see page 42 SHELVING SYSTEM For shelving systems see page 46 5U INFILL PANELS 5U infill panels can be fitted above and/or below a short length door. The U height of the door plus infill panel or panels must equal the total height of the rack. The 5U infills are pre-punched to accept three IP54 fans or filters. (The 800 wide 5U infill accepts 4 fans). The punched holes being sealed by three separate plates when fans are not specified. 600mm wide 800mm wide 17U steel door 567-565151K - 27U glazed door 567-565169B - 27U steel door 567-565153F - 32U steel door 567-565154D 567-565162E 37U glazed door 567-565171D 37U steel door 567-565155K 42U glazed door 567-565172B 567-565180C 42U steel door 567-565156L 567-565164A 5U infill panel 567-565130G 567-565131E IP54 intake fan 130 x 130mm 608-554255A IP54 extract fan 130 x 130mm 608-554721J IP54 filter 130 x130mm 608-554258F VERAK IP VERAK VERAK VERAK VERAK VERAK VERAK VERAK IP 27.66 IP 37.66 IP 37.68 IP 42.66 IP 42.68 IP 42.86 IP 42.88 Dimensions Height U 27 37 37 42 42 42 42 W x D 600x600 600 x 600 600 x 800 600 x 600 600 x 800 800 x 600 800 x 800 Main structure Frame 585-565025B 585-565041D 585-565042B 585-565049K 585-565050K 585-565053H 585-565054F For the top Top cover IP55 567-565296F 567-565296F 567-565297D 567-565296F 567-565297D 567-565300H 567-565301F Doors Glazed door 567-565169B 567-565171D 567-565171D 567-565172B 567-565172B 567-565180C 567-565180C Steel door 567-565153F 567-565155K 567-565155K 567-565156L 567-565156L 567-565164A 567-565164A Sides Side panels 567-565244C 567-565252D 567-565253B 567-565256G 567-565257E 567-565256G 567-565257E IP baying kit 567-565357A 567-565365B 567-565366L 567-565369E 567-565370J 567-565396E 567-565370J For the bottom of the rack Bottom gland plate 567-565320B 567-565320B 567-565321L 567-565320B 567-565321L 567-565324E 567-565325C Adjustable feet 567-565343A 567-565343A 567-565343A 567-565343A 567-565343A 567-565343A 567-565343A Heavy duty castors 567-565408K 567-565408K 567-565408K 567-565408K 567-565408K 567-565408K 567-565408K Lifting eyes 567-565489F 567-565489F 567-565489F 567-565489F 567-565489F 567-565489F 567-565489F 37
CABINETS VERAK EMC FEATURES AND BENEFITS NEW VERAK EMC High EMC attenuation High level shielding, helping systems meet EMC legislation Simplified cable entry Removable recessed panels enable cable entry into the rack from above or below the rear door IP 55 sealed Protects the system from dust, and water. Transparent doors Transparent door option is available which does not compromise the racks EMC shielding effectiveness and allow visual inspection of equipment without opening the door Robust cladding Protects the system in all shop-floor and industrial environments Heavy duty frame Allows fully loaded racks to be safely transported. The VERAK is capable of taking 750kg loads Supplied configured Racks delivered to site with all accessories fitted to the customer specification, thereby making installation quicker and easier Simple baying Racks can be linked together for larger applications quickly whilst maintaining the EMC and IP seal Accessories A full range of proven accessories are available to help with networking, electronic or electrical applications Styling A racking system with the appearance to complement the most advanced office, laboratory or manufacturing environment Thermal management EMC screened ventilation plates top and bottom allow natural or forced convection whilst maintaining integrity of EMC rack VERAK - EMC Range ex-stock Ex-stock sizes Other sizes available on application 27U 600x600mm 37U 600x600mm 37U 600x800mm 42U 600x600mm 42U 600x800mm 42U 800x600mm 42U 800x800mm Glass or metal door ATTENUATION db H -FIELD E -FIELD FREQUENCY MHz 38
NEW VERAK EMC CABINETS D DIM RACK WIDTH BOLT DOWN HOLES H CENTRE LINE FOR FEET & BOLT DOWN HOLES APERTURE L J K FEET CENTRES RACK DEPTH E DIM F DIM WIDTH BETWEEN VERTICALS APERTURE H 97,9 467,0 WIDTH BETWEEN VERTICALS G DIMENSIONS Height DIM A DIM C 12U 535,0 645,0 17U 757,3 867,3 22U 979,5 1089,5 27U 1201,8 1311,8 32U 1424,0 1534,0 37U 1646,3 1756,3 42U 1868,5 1978,5 47U 2090,8 2200,8 Shaded areas = not stocked 4,2 STANDARD TOP COVER 451,0 465,3 30,0 VENTED TOP COVER Heavy duty castor High top and high top side vented 59,7mm Add 30mm 'A'DIMENSION = 'B' U HEIGHTS 'C'DIMENSION = TOTAL RACK HEIGHT 59,7 451,0 20,0 GLAND PLATE APERTURE STANDARDS IEC 287-2 Rack dimensions EN 60950 Earthing IEC 529 IP rating -IP55 Verticals : 2.0mm steel End frames : 2.0mm steel Sides, doors : 1.6mm steel Tops covers : 1.2mm steel IP glass : 4.0mm toughened PAINT AND COLOUR SPECIFICATION Specification : Iron phosphate pre-treatment electropaint primer and textured powder top coat Zinc plating : Zinc plated and colour passivate Colour : Side panels, and internal mounting systems Pale gray RAL7035 Doors and top covers anthracite grey RAL 7016 Rack Rack Bolt Rack dimensions 'A' DIM 'B' Units 'C' DIM 'D' DIM 'E' DIM 'F' DIM 'G' DIM 'H' DIM 'J' DIM 'K' DIM 'L' DIM 'M' DIM width depth holes feet aperture aperture 27U x 600 x 600 1201.8 27 1311.8 597.6 678.0 490.0 440.0 558.0 380.0 450.0 393.4 363.8 27U x 600 x 800 1201.8 27 1311.8 597.6 878.0 490.0 640.0 758.0 380.0 450.0 593.4 363.8 27U x 800 x 600 1201.8 27 1311.8 797.6 678.0 690.0 440.0 558.0 580.0 650.0 393.4 563.8 27U x 800 x 800 1201.8 27 1311.8 797.6 878.0 690.0 758.0 580.0 650.0 593.0 593.4 563.8 37U x 600 x 600 1646.3 37 1756.3 597.6 678.0 490.0 440.0 558.0 380.0 450.0 393.4 363.8 37U x 600 x 800 1646.3 37 1756.3 597.6 878.0 490.0 640.0 758.0 380.0 450.0 593.4 363.8 37U x 800 x 600 1646.3 37 1756.3 797.6 678.0 690.0 440.0 558.0 580.0 650.0 393.4 563.8 37U x 800 x 800 1646.3 37 1756.3 797.6 878.0 690.0 640.0 758.0 580.0 650.0 593.4 563.8 42U x 600 x 600 1868.5 42 1978.5 597.6 678.0 490.0 440.0 558.0 380.0 450.0 393.4 363.8 42U x 600 x 800 1868.5 42 1978.5 597.6 878.0 490.0 640.0 758.0 380.0 450.0 593.4 363.8 42U x 800 x 600 1868.5 42 1978.5 797.6 678.0 690.0 440.0 558.0 580.0 650.0 393.4 563.8 42U x 800 x 800 1868.5 42 1978.5 797.6 878.0 690.0 640.0 758.0 580.0 650.0 593.4 563.8 Frame, top & bottom plates and inner EMC Zinc plated shielding panels on the doors and side panels zinc and colour passivate 39
CABINETS MAIN STRUCTURE DOORS FOR THE FRONT AND REAR OF THE RACK NEW VERAK EMC FRAME The frame comprises of 4 verticals and 2 end frames TOP/BOTTOM PLATES For VERAK EMC to work as an EMC enclosure top and bottom plates must be fitted. GLAZED DOOR RFI screened, tinted glass complete with swing handle. The required lock or lock blank needs to be ordered separately. SHORTENED STEEL DOORS AND 10U CABLE ACCESS PANEL A shortened steel door needs to be ordered separately from the 10U recessed cable access panel. The cable access panel is recessed by 60mm so cable connectors do not protrude out from the foot print The panel can be fitted above or below the door and is easily removed to facilitate the fitting of cable connectors etc. The 1.6mm steel door comes complete with swing handle. The required lock or lock blank needs to be ordered separately 40 PLAIN This plain EMC shielding panel which can be fitted at either the top or bottom of the rack can also be utilised as a cable entry panel VENTED The vented EMC shielding panel allows air to flow through the rack assuming a vented plate' is fitted at both the top and bottom of the rack and the rack is fitted with a ventilated top cover. A top mounted fan tray' can also be fitted under the top mounted vented plate to provide forced air cooling. See page 49 for fan tray details. STEEL DOORS 1.6mm steel door complete with swing handle. The required lock or lock blank needs to be ordered separately SWING HANDLES Both the metal and glass doors have a swing handle fitted as standard. Please note, the locks for the swing handle need to be ordered separately. Keyed alike lock - self locking All locks supplied operate with the same key and the door automatically locks when closed. Keyed alike lock - manual locking All locks supplied operate with the same key. To lock the door the key must be turned. Triangular key drive lock - self locking The lock is operated by a triangular machine cabinet drive. The door automatically locks when closed. Lock blank The lock blank fills the hole in the swing handle when a lock is not required. It also acts as a spring clip holding the handle into its housing. Keyed alike lock-self locking 802-563532F Keyed alike lock-manual locking 802-563610A Triangular key drive lock 802-563533D Lock blank 802-563534B
NEW VERAK EMC FOR THE SIDES TOP COVERS CABINETS LIFTING EYES Lifting eyes are sold as a kit of 4. Note, side vented and fully vented top covers must be removed before lifting eyes can be fitted. REMEMBER TO ORDER YOUR PANEL MOUNTS For panel mounting systems see page 42 SHELVING SYSTEM For shelving systems see page 46 SIDE PANELS Side panels are sold in pairs and are 1.6mm steel painted in RAL7035. The side panels are fitted using captive pozi drive screws which allow the units to easily fitted or removed. BAYING BRACKET KIT The kit consists of the required length of selfadhesive RFI contact fingers and IP gasket material plus 6 brackets which lock the two racks together to form a bayed suite of racks. For example: If three racks are to be bayed together to make one suite of racks, one pair of side panels are required (to be used either end of the suite) and two baying bracket kits. VERAK EMC PLAIN IP55 TOP IP 55 unvented top cover. SIDE VENTED TOP COVER This top allows convected air to flow out through the top. Note, for air to be able to flow through the rack a vented top and bottom plate must be fitted. FULLY VENTED TOP COVER A fully vented top is recommended when a fan tray is to be used. Note, for air to be able to flow through the rack a vented top and bottom plate must be fitted. VERAK VERAK VERAK VERAK VERAK VERAK VERAK EMC 27.66 EMC 37.66 EMC 37.68 EMC 42.66 EMC 42.68 EMC 42.86 EMC 42.88 Dimensions Height U 27 37 37 42 42 42 42 W x D 600x600 600 x 600 600 x 800 600 x 600 600 x 800 800 x 600 800 x 800 Main structure Frame 586-565089A 586-565105G 586-565106E 586-565113H 586-565114F 586-565117E 586-565118J Top/bottom plates Top vented screen 571-565410G 571-565410G 571-565411E 571-565410G 571-565411E 571-565414K 571-565415H Bottom vented screen 571-565418B 571-565418B 571-565419L 571-565418B 571-565419L 571-565422L 571-565423J Top & bottom plain 571-565336D 571-565336D 571-565337B 571-565336D 571-565337B 571-565340B 571-565341L Doors Glazed door full length 571-565201E 571-565203A 571-565203A 571-565204K 571-565204K 571-565212L 571-565212L Steel door full length 571-565185K 571-565187F 571-565187F 571-565188D 571-565188D 571-565196E 571-565196E 10U cable panel 571-565146J 571-565146J 571-565146J 571-565146J 571-565146J 571-565147G 571-565147G Shortened steel door 571-565183C 571-565185K 571-565185K 571-565186H 571-565186H 571-565194J 571-565194J For the sides Side panels 571-565276G 571-565284H 571-565285F 571-565288L 571-565289J 571-565288L 571-565289J EMC/IP baying kit 571-565389E 571-565397F 571-565398D 571-565401H 571-565402F 571-565401H 571-565402F Top covers Plain IP55 top 567-565296F 567-565296F 567-565297D 567-565296F 567-565297D 567-565300H 567-565301F Side vented top 571-565304L 571-565304L 571-565305J 571-565304L 571-565305J 571-565308C 571-565309A Fully vented top 571-565312A 571-565312A 571-565313K 571-565312A 571-565313K 571-565316D 571-565317B For the bottom of the rack Adjustable feet 567-565343A 567-565343A 567-565343A 567-565343A 567-565343A 567-565343A 567-565343A Heavy duty castors 567-565408K 567-565408K 567-565408K 567-565408K 567-565408K 567-565408K 567-565408K Lifting eyes 567-565489F 567-565489F 567-565489F 567-565489F 567-565489F 567-565489F 567-565489F 41
GENERAL CABINET ACCESSORIES 19" PANEL MOUNTING ANGLE SIMPLE 19" PANEL MOUNTING ANGLES METRIC PANEL MOUNTS 11.50 SIMPLE 19"FIXED PANEL MOUNTING ANGLES METRIC ETSI PANEL MOUNTS 42 97.9 NEW 19" PANEL MOUNTING ANGLES - PAINTED OR CONDUCTIVE Panel mounts are supplied in pairs to provide 19" mounting positions with hole patterns to accept captive nuts on universal centres. Incorporated into the design of the mounts are notches in the centre of each U height which makes the positioning of cage nuts much simpler. The panel mounting may be attached directly to the corner vertical in which case front to rear adjustment is 60mm per panel mount, or may be fitted onto panel mount angle supports giving infinite adjustment throughout the depth of the rack. CONDUCTIVE VERSION The conductive 19" panel mounting angles are the same as above but are finished in zinc and passivate. This provides earth continuity between the 'panel mount' and equipment mounted onto it. Painted - 2mm steel, painted in RAL 7035 Conductive - 2mm steel, zinc & passivate CONTENTS OF KIT 2 panel mounting angles Fixings 4 screws (12-37U) 6 screws (42-47U) Height (U) Finish 6 Painted 802-562413H 12 Painted 802-560498F 17 Painted 802-560503F 22 Painted 802-560508G 27 Painted 802-560513C 32 Painted 802-560518D 37 Painted 802-560523L 42 Painted 802-560528A 47 Painted 802-560533H 42 Zinc and passivate 802-563592K Simple 19" panel mounts are supplied in pairs to provide 19" mounting positions on universal centres. The centre of each U height is notched, making the positioning of cage nuts much simpler. Simple 19" panel mounts may be attached directly to the corner vertical, 60mm from the front door, or onto panel mount angle supports giving adjustment throughout the depth of the rack in 20mm steps.they allow directly fixed chassis trays (see page 44) to be used when the panel mounts are fitted onto the verticals. Simple 19" panel mounts have no side mounting positions. 2mm steel, painted in RAL 7035 CONTENTS OF KIT 2 fixed panel mounting angles Fixings 4 screws (12-37U) 6 screws (42-47U) SIMPLE 19" PANEL MOUNTING ANGLES Height (U) 12 802-562367L 17 802-562372G 22 802-562377H 27 802-562382D 32 802-562387E 37 802-562392A 42 802-562397B 47 802-562402B Metric panel mounts are supplied in pairs to provide 19" mounting on SU (metric) centres. These panel mounts allow for the fitting of Metric Modular Order or ETSI (European Telecom Standard Initiative) equipment. Metric panel mounts may be attached directly to the corner vertical in which case front to rear adjustment is 60mm; or they may be fitted onto panel mount angle supports giving infinite adjustment throughout the depth of the rack. 2mm steel, painted in RAL 7035 CONTENTS OF KIT 2 metric panel mounts Fixings 4 screws (12-37U) 6 screws (42-47U) METRIC PANEL MOUNTS U Height (SU) 12 21 802-562416B 17 30 802-562421J 22 39 802-562426K 27 47 802-562431F 32 56 802-562436G 37 65 802-562441C 42 74 802-562446D 47 83 802-562451L M6 x 12mm SCREW & M6 WHIZZ TIGHT NUT FIXINGS M6 x 12mm screw 802-561040D M6 whizz tight nut 802-561041B Sold in packs of 100
GENERAL CABINET ACCESSORIES SLIDING CAGE NUT PANEL MOUNTS & 'U' SPACING LOCATION STRIP SLIDING CAGE NUT PANEL MOUNTS Sliding cage nut' panel mounts are supplied in pairs to provide 19 mounting or SU (metric) centres. The sliding cage nuts are easily front loaded into the panel mounts and allow infinite adjustment of equipment up and down. The panel mount itself is an aluminium extrusion which provides earth continuity between mounted equipment and the panel mount. U SPACING LOCATION STRIP As an accessory to the sliding cage nut mount U spacing location strips are available in pairs. The U spacing location strips, slide into the tee slots in the panel mount. They provide defined U spacing into which the sliding cage nuts will locate, thereby aiding the alignment of equipment. The location strips do not inhibit the ability of the nuts, or equipment, to be slid up or down the panel mounts. Sliding cage nut panel mounts 42U 802-563600D U spacing location strip 42U 802-563608K For sliding cage nuts and front panel screws see page 54. Panel fixings, sliding cage nut system M6x10mm pozi drive screws, bright zinc. Pack 100 645-557764H M6 black plastic cup washers to suit above. Pack 100 645-555388J M6 sliding cage nut. Pack 100 645-557765F PANEL MOUNT ANGLE SPACING BRACKET PANEL MOUNTING ANGLE SUPPORTS (600mm wide racks or for Token ring panel mounts) TYPE 1 PANEL MOUNTING ANGLE SUPPORTS These fit between vertical members to allow full adjustment of the panel mounts at any position along IMRAK s framework. Equipment can, as a result, be fitted flush with the front face of the side panel or inset all the way to the rear of the unit. Units occupy 1U of height. 1,6mm steel, painted in RAL 7035 Complete with fixings CONTENTS OF KIT 2 panel mounting angle supports 4 clips (2 left hand; 2 right hand) Note: Use 2 kits up to 37U high 3 kits for 42U & 47U high PANEL MOUNTING ANGLE SUPPORTS PANEL MOUNT ANGLE SPACING BRACKET This bracket can only be used with 600mm wide racks when the 'panel mounting angle supports' have been mounted in the outer positions on the vertical, out towards the side panel. With the use of the 'panel mount angle spacing bracket' the 'panel mount angles' can be set into the rack. Thereby providing extra space for cabling at the front and rear of the panel mount angles. 1.6mm steel, painted in RAL 7035 CONTENTS OF KIT 2 panel mount angle spacing brackets Fixings Note: Depth 400 802-560544C 600 802-560545A 800 802-560546K 900 802-560547H Use 2 kits up to 37U high 3 kits for 42U & 47U high PANEL MOUNT ANGLE SPACING BRACKET 802-563574A REDUCING CABLE CHANNEL Shown fitted withpanel mounting angles and double cable hoops REDUCING CABLE CHANNELS Reducing cable channels are suitable for 800mm wide racks only.these units are supplied in pairs and may be attached directly to the corner vertical, or fitted onto panel mount angle supports giving infinite adjustment throughout the depth of the rack.reducing cable channels have been designed to support 'panel mounting angles'. The appropriate size and type of 'panel mounting angles' also need to be ordered. S 1.6mm steel, painted in RAL 7035 CONTENTS OF KIT 2 reducing cable channels Fixings REDUCING CABLE CHANNELS Height (U) 6 802-563565B 12 802-563566L 17 802-563567J 22 802-563568G 27 802-563569E 32 802-563570J 37 802-563571G 42 802-563572E 47 802-563573G CROSS MEMBERS Cross members fit across the rack between the corner verticals to allow for economical fitting of DIN mounting rails, mounting of cable trays or to offer support for cables at the rear of the rack. The use of 2 or 3 members allows customers to attach their own design of rear mounting panels. 1,6mm steel, painted in RAL 7035 CONTENTS OF KIT 1 cross brace 2 clips (1 left hand; 1 right hand) CROSS MEMBERS Rack dimensions 600 wide 802-560552D 800 wide 802-560553B 43
GENERAL CABINET ACCESSORIES CHASSIS SUPPORTS 451 / 651 These steel supports may be varied along the depth of the rack and offer an ideal method of supporting heavy equipment. When used in conjunction with KM6-II cardframes they allow every cardframe to be supported without loss of U height. The horizontal sections of the supports are prepunched to allow the chassis trays to be fitted without further drilling. An extra 15mm width is available when chassis supports are fitted directly to panel mounting angle supports as maximum chassis width is then 465mm.The nominal load rating is 50k g. The 370mm/570mm long supports are intended to be fitted when panel mounts are inset greater than 60mm in 600 & 800 deep racks. CHASSIS SUPPORT COMPLETE WITH CHASSIS TRAY 394 / 594 467 / 667 474 / 674 417 / 617 490 / 690 (Note: If higher loads are required a second support can be inserted under the first in an inverted position). CHASSIS TRAYS AND SUPPORTS Number in kit To suit rack size Actual length Chassis supports pair 400mm deep 270 802-561009J Chassis supports pair 500mm * 370 802-561561J Chassis supports pair 600mm deep 470 802-561010B Chasss supports pair 700mm* 570 802-561562G Chassis supports pair 800mm deep 670 802-561011L *There are no 500 & 700mm deep racks, but the chassis supports are intended for use when panel mount angles are inset by say 120-150mm etc. CHASSIS TRAYS FOR 19" These steel trays come in 4 depths so that the correct depth for your installation may be selected without interfering with cabling or power distribution at the rear. The slots in the tray allow for good airflow and at the same time offer a selection of fixing positions to allow modems and instruments to be screwed into position. With this style of tray a pair of chassis supports is also required. Note: The units for 600 or 800 wide may be supported on chassis supports bolted to panel mounting angle supports. CHASSIS TRAYS Note: For 600 wide units fitted on chassis supports and in turn on panel mountings, 4 panel mountings must be fitted. CANTILEVER SHELVES These unique cantilever shelves fix onto the verticals via bayonet tabs & are retained via the plastic clips supplied. This permits the use of the 19" fixed panel mounting angles in front of the shelf. They are available in 2 & 3U heights respectively. Cantilever shelf : 1.6mm steel zinc pale grey RAL 7035. Number in kit 600mm wide racks 800mm wide racks Chassis tray 256mm 1 802-561013G 802-561017K Chassis tray 356mm 1 802-561014E 802-561018H Chassis tray 456mm 1 802-561015C 802-561019F Chassis tray 556mm 1 802-561016A 802-561020K Depth Load rating 2U shelf 255mm 20kg 844-247854L 3U shelf 400mm 20kg 844-247855J 44
220,0 420,0 620,0 GENERAL CABINET ACCESSORIES 492,8 692,8 CHASSIS TRAYS TO FIX DIRECTLY TO VERTICAL MEMBERS These trays are designed for applications where equipment wider than 19" is to be mounted or used in conjunction with fixed panel mounts. As they are fitted directly to the vertical corner members, no chassis supports or panel mounting members are required, thereby reducing cost and complexity. Note: These can be used with fixed panel mounts when fitted to the vertical (NOT on panel mount supports) but not when standard panel mounts are used. CHASSIS TRAYS TO FIX DIRECTLY TO VERTICAL MEMBERS 1.6mm steel : Zinc plate and passivate Number Depth of 600mm wide 800mm wide in kit rack rack rack Direct mounting trays 1 400mm deep 802-563557A 802-563561K Direct mounting trays 1 600mm deep 802-563558K 802-563562H Direct mounting trays 1 800mm deep 802-563559H 802-563563F Nominal load per shelf 600 wide 50kg Nominal load per shelf 800 wide 20kg HEAVY DUTY SHELVES For applications where very heavy loads are required, these shelves offer a load capacity of 100kg. Slotted holes offer limited air passage and also provide simple fixing positions. Note: If a load of 50Kg to 100kg is to be fixed, specify 2 pairs of chassis supports per shelf and reverse the second pair under the first pair. Shelf : 1.6mm steel Finish : Zinc plate and passivate HEAVY DUTY SHELVES 600 wide racks 800 wide racks 472mm deep 802-552914C 802-552917H 627mm deep 802-552915A 802-552918F 754mm deep 802-552916K 802-552919D 19" CANTILEVER SHELVES Cantilever shelves fix directly onto the standard 19" panel mounts. The shelves occupy 2U of panel mount height. APPLICATIONS Ideal for networking applications and modem mounting. Shelf : 1.6mm steel Finish : Painted in RAL 7035 CANTILEVER CHASSIS SUPPORTS Cantilever chassis supports fix directly onto Panel Mounting Angles. These supports can be used to support equipment by themselves or with a Chassis Tray 256mm mounted on them. Nominal load per pair of cantilever chassis supports 20kg. 400MM DEEP CANTILEVER SHELF Cantilever supports : 1,6mm steel Finish : Zinc plate and passivate CANTILEVER CHASSIS SUPPORTS CANTILEVER CHASSIS SUPPORTS Pair of cantilever chassis supports 802-563106A 258mm 255MM DEEP CANTILEVER SHELF 255mm deep 802-562284D 400mm deep 802-562285B Nominal load per shelf 20kg. mounted in the centre of the shelf. 45
GENERAL CABINET ACCESSORIES SLIDING SHELVES A range of sliding shelves are available which when used with the slides and special bobbins allow the same shelf to be used with both single and double extension slides. Short shelves may be used on larger slides eg: the 400mm shelf on slides to suit 600mm deep racks. Maximum load capacity is 35kg. 16mm steel : Zinc plate and passivate CONTENTS OF KIT 1 shelf 4 mounting bobbins for 400mm deep version 6 mounting bobbins for 600mm deep version 8 mounting bobbins for 800mm deep version SHELF FITTED TO SLIDES SLIDING SHELF KIT SLIDING SHELVES For 600 wide racks For 800 wide racks To suit Actual To suit Actual rack depth length rack depth length *400 240 802-563082L 400 240 802-563085E 600 440 802-563083J 600 440 802-563086C 800 640 802-563084G 800 640 802-563087A *Note: This shelf is for use in deeper racks where only a short shelf is required. SLIDE KIT SLIDES Single and double extension slides come complete with brackets for use with the sliding shelves above. The brackets can be used either fitted to the 19" mountings or fitted directly into the verticals, and hence can be used with a ready rack which has only 1 pair of panel mounts. Slides can be fitted to either 600 or 800mm wide racks. The slides come fitted with threaded inserts to take the bobbins. Caution: Heavy loads mounted on slides can make a rack unstable. Please ensure that the rack is bolted down or have an extension plinth fitted. SLIDES Single extension slides to suit 600 deep rack 802-552926G Single extension slides to suit 800 deep rack 802-562462F Double extension slides to suit 600 deep racks actual length 483 mm 802-552927E Double extension slides to suit 800 deep racks actual length 686 mm 802-552928C Supplied in pairs complete with brackets. AIR DUCTING TRAY 19" The tray is 1U high and can be attached to a subrack or a 19" rack to direct air into or out of the rack. AIR DUCTING TRAY 19" 632-554172D The integrated chassis supports will make it easy to put subracks above the tray. AIR DUCTING TRAY 19"
MOUNTING RAILS Two types of standard assembly rails are available, both are 585mm in length and are supplied with fixings for mounting onto an IMRAK 'cross member', page 43. Note the 'cross member' needs to be ordered separately. GENERAL CABINET ACCESSORIES WITHDRAWABLE DESK UNIT WITHDRAWABLE DESK UNIT Withdrawable desk units provide a retractable writing surface to suit any range of 19" racks.they only occupy one U of panel space and are supplied complete with telescopic slides that have hold-in springs fitted. Panel mounts are required in the front and the rear of the rack to fit this unit. Front panel : 3mm steel, painted in RAL 7035 Handle Writing surface Telescopic slides : Extruded aluminium : Grey linette plastic laminate on blockboard base These items are not available ex-stock : Steel Rack Extended suited depth IMRAK 600 deep 367 607-552998F IMRAK 800 deep 445 607-552999D Top Hat Profile DIN 46277 35mm x 7,3mm 802-563108H 'C' Profile Mounting Rail 35mm x 18mm 802-563386B 2U KEYBOARD HOUSING This high quality keyboard housing occupies 2U of usable height and comes complete with a lockable drop down front panel. It is suitable for marquardt keyboard type 7064 or cherry type G80-1800 which can be screwed in position with two screws or with the cherry keyboard is fitted with a velcro strip. The keyboard is mounted on high quality slides which offer positive stop'' both in and out. In addition, the front part of the tray is usable as a handle or pencil holder. The usable aperture is 50 x 426mm. 2U Keyboard housing 802-556070J Velcro mounting kit 802-562178C 1U KEYBOARD AND HOUSING This space saving keyboard occupies only 1U in height and is a totally enclosed unit. When open, the keyboard tilts to an ergonomic 12 and is IBM AT/XT compatible. 483 ca. 420 1U 250 28 FIXED DESK UNIT FIXED DESK UNIT The fixed desk unit provides a flat rigid writing surface suitable for fitting to any standard 19" rack. It occupies only 2U of panel height and has a writing surface 445mm wide by 305mm deep. 3 12 1,6mm steel fitted to a 3mm steel panel. Painted in RAL 7035 These items are not available ex-stock 607-553000C Note: These units may be used in 19'' racks which have mounting centres within the range shown. 1U KEYBOARD AND HOUSING 1U Keyboard type cherry G 80-0777 International Style IBM AT/XT compatible 898-10001H 440mm wide 250mm deep Spiral cable XT/AT compatible 898-10019B
GENERAL CABINET ACCESSORIES SWING FRAMES Swing frames are designed to allow easy access to the rear of equipment, particularly when the location of the racks restricts or prohibits rear access. When racks are bayed together in suites, swing frames allow access to the side and rear of the equipment. Swing frames are available in four sizes to suit 42U high racks (usable height 39U), 37U high (usable height 34U), 22U (usable height 19U) and 17U (usable height 14U). Any swing frame may be used in a rack equal to or greater than the U mounting height dimension (eg: a 42U swing frame in a 47U rack). The smaller swing frames enable you to fit some of your equipment in a fixed position, and the rest in a swinging position. (Remember to order shelves or panel mounts for the remaining aperture). All swing frames can be pivotted in more than one position. When selecting the left hand position (see diagram position 1) the swing frame will enable 450mm deep cardframes and equipment to clear the vertical members. When the swing frame is in its left hand position, an infill panel may be used which offers extra mounting positions for switches and meters etc., as well as giving a neat and pleasing appearance to the system. Note: If an infill panel is not ordered, the swing frame will be built with the pivot in the centre position unless otherwise specified at the time of ordering. By inverting the whole system it is possible to change the swing frame to a right hand pivot system. Safe working load of the swing frame is 100kg. Caution: A rack with a swing frame should be fitted with an extension plinth or bolted down to ensure that it will not tip over when the swing frame is operated. 2 1 BRACKET MOUNTING DETAIL PLAN VIEW OF SWING FRAME SWING FRAMES 48 Dimensions U (mounting) U (usable) Swing frame Infill panel 42 39 802-560584B 802-560695D 37 34 802-560579F 802-560690C 22 19 802-560564H 802-560675K 17 14 802-560559A 802-560670J Swing frames can only be fitted in 800mm wide cabinets.
THERMAL MANAGEMENT STANDARD FAN TRAYS Top mounted fan trays are available to aid the cooling of your equipment. These may be retrofitted to the IMRAK 1400 versions and occupy none of the usable U height. Fan trays are supplied with or without fans. Top fan trays have blanking plates fitted in all unused positions. Connection to all fan trays is by means of a CEE 22 mains inlet, ordered separately GENERAL CABINET ACCESSORIES TOP MONITORED FAN TRAYS Each fan is monitored by its own independent chip housed on a motherboard. These chips monitor the speed of every fan by measuring the current commutation pulses. If the fan is braked by an obstruction or fails completely, indication is given via the LED being extinguished and the audible alarm sounding. If remote monitoringis required this can be acheived by removing the available alarm and using the TTL facility and the relay to give a signal out. This is a non-latching output signal and once the fan speed returns to normal the LED will be illuminated. The TTL facility will go high and the relay de-energise. TOP MONITORED FAN TRAYS Dimensions (W x D) 600 x 600 802-563099E 600 x 800 802-563100B 800 x 600 802-563103G 800 x 800 802-563104E STANDARD FAN TRAYS Non-stock available on Special Order. IMRAK FAN TRAY ACCESSORIES Additional blanking plates 802-503897B Single fan connection lead 28-241569C 3 link AC daisy chain 28-555230B 4 link AC daisy chain 28-555231K 6 link AC daisy chain 28-555232G 2m mains lead with CEE22 plug, and 13amp (UK) plug fitted 802-561559G 2m mains lead with CEE22 plug, and Schuko plug (German/French) 802-562463D INSERTED FANS FOR PERSONAL CONFIGURATIONS Dimensions (W x D) Top with fans* Number of fans in tray Top tray As supplied Max. number without fans 600 x 400 802-560474J 2 2 802-560482K 600 x 600 802-560475G 4 6 802-560483H 600 x 800 802-560476E 4 6 802-560484F 600 x 900 802-560477C 4 8 802-560485D 800 x 400 802-560478A 3 3 802-560486B 800 x 600 802-560479K 4 6 802-560487L 800 x 800 802-560480C 4 9 802-560488J *Supplied with 28-238116F fans Input Dims. Airflow Bearings Noise Voltage Frequency Power mm CFM M 3 /hr db(a) V watts 120 x 120 x 25 64 110 Sleeve 43 220 VAC 50 18,0 28-243081K 120 x 120 x 38 95 160 Sleeve 43 220 VAC 50 22,0 28-238116F 120 x 120 x 38 70 117 Sleeve 36 220 VAC 50 10,0 28-243083D 120 x 120 x 38 95 160 Sleeve 44 115 VAC 50 22,0 28-243084A 120 x 120 x 38 109 184 Sleeve 46 12 VDC - 6,5 28-243085J 120 x 120 x 38 109 184 Sleeve 46 24 VDC - 6,7 28-243086F LOW NOISE FAN TRAYS Low noise top mounted fan trays are available to aid the cooling of your equipment. They may be fitted after your equipment on the IMRAK 1400, and occupy none of the usable U height. Connection to all fan trays is by means of a CEE22 mains inlet, ordered seperately. LOW NOISE FAN TRAYS Dimensions (W x D) Number of fans 600 x 600 4 802-563089H 600 x 800 4 802-563090A 800 x 600 4 802-563093F 800 x 800 4 802-563094D THERMOSTAT- FZK180 AND THERMOSTAT WIRING KIT Thermostat FZK180 can be used to control either the standard or low noise top mounted fan trays. The adjustment range is from 10 c to 60 c. The Thermostat wiring kit contains all the necessary parts including thermostat mounting, cable ties, grommets and wiring instructions to achieve a thermostat controlled roof mount fan tray. FZK180 Thermostat 608-554266G Thermostat wiring kit 802-563585G For more details regarding the Thermostat FZK180 see page 2.66 in the Handbook. Note: Personal configurations are achievable when using the fans in the above table with basic IMRAK fan trays 49
GENERAL CABINET ACCESSORIES EARTH CONTINUITY KIT Two styles of earth continuity are available. Each contains 10 leads to earth all panels, doors and leaving extra leads to earth parts of the electronic equipment. Type 1 has ring terminals at both ends to mount directly onto the earth studs on the panels. Type 2 has a ring terminal on one end and a spade (faston) at the other. Adaptor rings are provided for bolting on to the earth studs to allow quick removal and assembly. 6X... 4X... 29X... 4X... 22X... 16X... 28X... 7X... TYPE 1 TYPE 2 2X... 4X... 4X... 29X... 4X... 22X... 16X... 28X... 7X... 8X... EARTH CONTINUITY KITS Earth continuity kit Type 1 802-560005L Earth continuity kit Type 2 802-561563E EARTHING BARS EARTHING BARS These earthing bars offer the option of bonded earth or isolated earth condition by using insulated spacer strips. They have male spade fixing positions at ¹/₂ U intervals and can be mounted on any flat surface. Mounting holes allow mounting without further drilling on the inside faces of IMRAK as illustrated. Made from nickel plated copper, the earth Busbars have a rating of 40 amps and can be cut to length. Main earth is provided by an M6 stud at both ends. EARTHING BARS Earthing Bar 13U 802-552929A Earthing Bar 27U 802-552930E Earthing Bar 39U 802-552931C BUSBAR SYSTEM - EARTHING This is a copper common earth/neutral busbar which is normally fitted to the rear vertical members of the rack. It is rated at 140 amps and supported by polyamide insulating blocks which will accept 4mm, ⁵/₃₂'' or 6BA fixing screws.there are three sizes of terminals for conductor sizes 1,5 to 35mm. Note:The busbar is simply fitted to the blocks using 'snap-on' clips. BUSBAR SYSTEM - EARTHING Qty Copper bar 10mmx3mmx1000mm 1 613-10475C Insulated Mtg. Block 20 613-10476L Large Terminal 16-35mm conductor 20 613-10479B Small Terminal 1,5-4mm conductor 50 613-10477H Medium Terminal 4-14mm conductor50 50 613-10473J Busbar kit 1 802-556088A BUSBAR KIT Busbar kit contains the fllowing items:- 1 copper bar 10mm x 3mm x 1000mm 3 insulated mounting blocks 1 large terminal 16-35mm conductor 10 small terminals 1.5-4mm conductor Note: this is part of BUSBAR SYSTEM - EARTHING ELECTRO-STATIC POINT (E.S.P.) This E.S.P. is designed to protect against electrostatic discharge with its consequential damage to electronic equipment. This self-tapping screw stud will be fitted on the mid-point of the front left-hand vertical, unless otherwise stated. ELECTRO-STATIC WRIST STRAP AND LEAD To be used with the E.S.P. Electro-static point (E.S.P.) 802-563039A Electro-static wrist strap and lead 802-563040E 50
GENERAL CABINET ACCESSORIES CABLE BAR CABLE HOOPS CABLE MANAGEMENT Seven alternative products are offered which are suitable for use in any rack. Plastic cable trunking. A plastic trough measuring 80mm wide by 40mm deep externally with snap-on cover. Supplied in 2m lengths and easily cut for other sizes. Steel cable trays. Four alternative lengths, all152mm wide by 12,7mm deep and multipunched for accepting cable ties, etc. Plastic cable trays. 1500mm x 135mm wide by 13mm deep, multi-punched for accepting cable ties etc. Easy to cut and will not damage or cut into cables. Cable hoops. For neat cable management, hoops can be fixed to the inside face of the vertical corner members. Single sized hoops are available for racks with side panels, and double hoops for racks which are bayed together. Hoops may also be fitted on cross members at the rear of the rack or from panel mount supports on the side of the rack. Cable bar. For 19" mounting and supporting cable at the rear of panel mounts. CABLE MANAGEMENT PANELS 2U cable entry 960-236702E 1U brush strip panel 802-563107K 1U cable management panel 802-563522J 1U cable management panel with extra large hoops 802-563536J 2U cable management panel 802-563523G CABLE MANAGEMENT PANELS IN BLACK 1U cable management panel 802-563575K 1U cable management panel with extra large hoops 802-563576H 2U cable management panel 802-563577F All panels supplied with fixings DOCUMENT HOLDER A plastic self-adhesive document holder is available which can be fixed to any flat surface. It is available in A5 and A4 sizes. DOCUMENT HOLDER W x H x D (mm) A5 size 250x145x21 802-553082F A4 size 355x195x21 802-553081H CABLE MANAGEMENT Plastic trunking 2m long 643-10000F Steel cable tray 32U 802-560871K Steel cable tray 37U 802-560876L Steel cable tray 42U 802-560881G Steel cable tray 47U 802-560886H Plastic cable tray 37U 802-562414F Single cable hoops 802-563545H Single cable hoops pk. of 10 802-563612H Double cable hoops 802-563546F Double cable hoops pk. of 10 802-563613F Cable bar 19" 961-553948B CABLE MANAGEMENT LOOP 1 pair of cable management loops 960-228781A MAGNETIC FIBRE OPTIC CABLE HOLDER This simple device consists of a plastic bobbin with a magnet on the rear face allowing it to be mounted to any steel surface. The diameter of the bobbin prevents the fibre optic cable from bending at too tight a radius. Fibre optic holder 802-552932A 51
GENERAL CABINET ACCESSORIES ELECTRICAL PANELS Available for both 600 and 800mm wide racks for 32, 37 & 42U heights, these electrical panels facilitate easy mounting of all non-19" components from DIN mounting rails to switch gear and relays etc. Two types of mounting brackets are available: Type 1 for fitment with panels between the rear verticals consists of 4 mounting brackets, 2 nylon support blocks & fixings. Type 2 is used in conjunction with panel mount supports and provides 2 nylon support blocks with screws and spacers to allow panels to move throughout the depth of the rack. 2,5mm steel, painted orange. ELECTRICAL PANEL Height Rack width (panel only) 37U 600 802-560736E 42U 600 802-560741A 37U 800 802-560782J 42U 800 802-560787K MOUNTING BRACKETS Type Rack width 1 600 & 800 802-552911J 2 600 & 800 802-552912G TYPE 1 MOUNTING TYPE 2 MOUNTING PRE-PUNCHED MOUNTING PANEL This panel allows fixing of any component without drilling, easy management of cables and good rigidity. The panel is 534mm x 660mm (15U), width x height, and should be mounting on two 'cross members' (see page 43). Note, this item cannot be fitted in any position which coincides with the 'panel mount angle supports' on a 600 wide rack due to the panel widths. Pre-punched panel 534 x 660 802-563074K MOUNTING RAILS Two types of standard assembly rails are available, both are 585mm in length and are supplied with fixings for mounting onto an IMRAK 'cross member', page 43. Note the 'cross member' needs to be ordered separately. Top Hat Profile DIN 46277 35mm x 7,3mm 'C' Profile Mounting Rail 35mm x 18mm 802-563108H 802-563386B PRE-PUNCHED MOUNTING PANEL 52
PANELS GENERAL CABINET ACCESSORIES We offer a comprehensive range of panels in aluminium to suit both 19" and half width practices. In addition, ventilated panels are available to provide an inlet of air for racks and enclosures. Panels are also available in 3mm steel (plain) or 1,6mm flanged. These are subject to a minimum order quantity of 25 units. 3mm aluminium NS4 half hard. FINISH Code JS Anodised (WP) : Pale grey textured paint to IMRAK colour RAL7035 : Etch & anodised Code KT : Pebble grey semi gloss paint to RAL 7032 W A Z Note: The anodised front panels are Innished on the front face ONLY. The front face is denoted by the smooth sheer edges. W 1-6U A Y X 7-12U Y X A Z A 19" x 3mm ALUMINIUM FRONT PANELS - PLAIN Unit W A X Y Z height (notional) JS finish Anodised (WP) KT finish 1 483 6 44,45 32-644-552985C 50-0767G 50-10081J 2 483 6 88,90 76-644-552986A 50-0768B 50-10082E 3 483 38 133,35 57-644-552987K 50-0769H 50-10083A 4 483 38 177,80 102-644-552988H 50-0770C 50-10084H 5 483 38 222,25 146-644-552989F 50-0771J 50-10085D 6 483 38 266,70 191-644-552990K 50-0772D 50-10086L 7 483 38 311,15 57 89-50-225827J - 8 483 38 355,60 76 102-50-225828F - 9 483 38 400,05 121 102-50-24284D 50-10089K 10 483 38 444,50 165 102-50-24285L 50-10090H 12 483 38 533,40 191 133-50-24286G 50-10092L HALF WIDTH x 3mm ALUMINIUM FRONT PANELS - PLAIN 2 268 6 88,90 76 - - - 50-0763E 3 268 38 133,35 57 - - - 50-0764L 4 268 38 177,80 102 - - - 50-0765F 19" X 3mm ALUMINIUM PANELS VENTED Unit W A X Y Z height (notional) JS finish Anodised (WP) KT finish 1 483 6 44,45 32-644-552981L 50-24281E - 2 483 6 88,90 76-644-552982J 50-24282A - 3 483 38 133,35 57-644-552983G 50-24283H - 53
GENERAL CABINET ACCESSORIES SCREW M6 X 18 CUP WASHER SLIDING NUT CAGED NUT CUP WASHER PANEL FIXINGS PANEL SCREW COVERS The appearance of your rack may be enhanced by fitting these covers to hide the screw heads. They are supplied in 46U (2045mm) lengths suitable for cutting as required. The clips should be fitted approximately every 250mm and should be ordered separately as required. Extruded aluminium, satin anodised finish Clips : Spring steel UNIT IDENTIFICATION STRIPS These self-adhesive strips fit to the return flange of the rack's vertical member and simplify the task of positioning panels/equipment accurately on the U spacing. They are supplied in sections to suit racks up to 47U height and are easily cut for other sizes. Attractive silver metallic finish with black numerics. UNIT IDENTIFICATION STRIPS CAGED NUT INSERTION TOOL TYPE 1 PANEL SCREW COVERS 603-10099A Panel screw cover x 2045mm 802-562222D Fixing clips, pack of 10 802-562223B CAGED NUT INSERTION TOOL TYPE 2 PANEL FIXINGS Shown here are the fixings suitable for fitting front panels. They are available in packs of 10, 100 and 1000. PANEL FIXINGS s Caged nut insertion tool Type 1 50-2339E Caged nut insertion tool Type 2 802-557377L Pack 10 Pack 100 Pack 1000 M6 x 10mm pozi drive screws, bright zinc 645-557764H M6 black plastic cup washers to suit above 645-555388J M6 sliding cage nut 645-557765F M6 x 18mm reduced head screws, bright zinc - 645-555387L - M6 black plastic cup washers to suit above - 645-555388J - M6 x 18mm reduced head screws, bright zinc, complete with cup washers 50-3965A 50-202534F 50-202535C M6 12/14 swg (1.83mm - 2.64mm) caged nuts - for use with IMRAK panel mounts 50-3966G 645-10023F 50-202533J M6 x 18/20 swg (0.7mm - 1.6mm) caged nuts 50-2847G - - M6 plain washer, zinc plated - 645-10033B - 54
POWER DISTRIBUTION PANELS IMRAK and VERAK are international products designed for companies with global purchasing and supply strategies. We offer a wide range of power distribution panels (PDPs) for the majority of European and other international markets. BS 13 amp German Schuko French sockets Swiss sockets IEC CEE 22 inlet Many of the socket strips are available in 19" versions, ie. can be fitted across the rack with the longer versions offered in a vertical format. U.K. 7 WAY R.C.D. POWER STRIPS A 'Residual Current operated circuit breaker' is designed to protect the operator from electrical faults in equipment. If the electrical installation is in order, on any given circuit or piece of equipment, the ingoing current will be equal to the outgoing current. If, however, current can leak to earth via a failed installation, the ingoing current will not equal the outgoing current and a magnetic flux is created within the units transformer. This imbalance is used to activate the tripping device. The trip isolates all the poles from the mains supply. By pressing the units test button a fault condition is produced, thus testing the electrical and mechanical functioning of the R.C.D. The test button cannot, however test the electrical installation, only the R.C.D. This unit is APPROVED to BS 5733 and is fitted with an illuminated power indicator and 3 metres of cable plus a 13 amp plug. The unit can be bolted directly to the IMRAK vertical or alternatively it can be vertically bolted to the 19" panel mounts with the use of a mounting bracket (640-912784H) Technical Data Operating voltage : 250V AC max. I n : 30 ma (To BS4293) Maximum rated current : 13A total load Operating temperature range : -25 to +40 C Width x height x total length 7 way R.C.D. 67 x 48 x 689mm 640-912852F U.K. 13 AMP SOCKETS, VERTICAL MOUNTING These units are APPROVED to BS5733 and are available with either an illuminated switch or as a non-switched version. Both units are fitted with an external earthing position and the unit comes complete with 3 metres of cable and 13 amp plug. The units can be bolted directly to the IMRAK verticals or alternatively can be bolted vertically to the 19" panel mounts with the use of a mounting bracket (640-912784H). The units are 67mm wide and 48mm high. Total length 6 way switched 467mm 640-912636A 9 way switched 689mm 640-912637K 13 way switched 911mm 640-912639F 6 way non-switched 467mm 640-912631L 9 way non-switched 689mm 640-912632J 13 way non-switched 911mm 640-912634E Mounting bracket - 640-912784H U.K. 13 AMP SOCKETS, 19" MOUNTED OR VERTICAL MOUNTED These units are APPROVED to BS5733 and are available with either an illuminated switch or as a non-switched version. Both units are fitted with an external earthing position and the unit comes complete with 3 metres of cable and 13 amp plug. The units can be bolted vertically onto the IMRAK panel mounts using the 'vertical mounting bracket', or alternatively can be bolted to the 19" panel mounts horizontally with the use of a 19" mounting bracket. The units are 67mm wide and 48mm high. Total length 5 way switched 407mm 640-912635C 5 way non-switched 407mm 640-912630B 19" mounting bracket - 640-912732E Vertical mounting bracket - 640-912784H GENERAL CABINET ACCESSORIES U.K. 7 WAY FILTERED POWER STRIPS A two-stage interference filter with very high attenuation levels for both common mode and differential mode interference is enclosed in a 7 way U.K. power strip. Intended for very sensitive equipment, or environments where interference is frequent and very intensive. The unit is equipped with ground line choke to give a additional protection against common mode interference This unit is APPROVED to BS 5733 and is fitted with an illuminated switch and 3 metres of cable plus a 13 amp plug. Note; plug is fitted with 10 amp fuse to match the max. current rating of the filter. The unit can be bolted directly to the IMRAK verticals or alternatively it can be bolted to the 19" panel mounts with the use of a mounting bracket (640-912784H) Technical Data Max. Rated current (40 C) : 10 amps Operating voltage : 250V AC max. Operating temperature range : -25 to +85 C Max. leakage current (250V 50Hz) : 2 x 0.21mA Width x height x total length 7 way, filtered, 67 x 48 x 689mm 640-912856J switched CEE 22 (IEC SOCKET) 19" MOUNTED OR VERTICAL MOUNTED Metal bodied socket strip containing 7 outlets. The unit is supplied with a 3 metre lead and UK 13 amp plug (Note: plug is fitted with a 10 amp fuse). The unit has an illuminated switch and its dimensions are 67mm wide and 48mm high. This socket strip can be bolted vertically onto the IMRAK panel mount angles using the vertical mounting bracket or alternatively can be bolted across the 19" panel mounts horizontally with the use of the 19" mounting bracket. Total length CEE 22 (7 way) switched 407mm 640-912900K 55
GENERAL CABINET ACCESSORIES MOUNTING BRACKETS VERSION 1 MOUNTING BRACKETS VERSION 2 SWISS SOCKETS PLASTIC BODY VERSIONS This is a 6 way unit with a switch which has on/off neon indicator. Supplied with a min. 2m of cable. 56 SCHUKO (GERMAN) SOCKETS This aluminium extrusion occupies only 1U in height but still allows for seven sockets, on/off neon switch and fuse (10 amp rated) and comes complete with a 1,5 metre lead and schuko plug. Note: Adaptor brackets must be ordered separately for 19" or vertical mounting. German 7 way Type C 640-10012J 6 way Type A 802-562464B SCHUKO (GERMAN) PLASTIC BODY VERSIONS Five sizes are available (4, 6, 8, 12 and a 19" 6 way) rated at 220V/230V/ 10A. Each plastic bodied socket strip has a switch with on/off indicator and is delivered with min. 2m of cable. This strip is mounted on the rack verticals or shelves. Grey with black sockets. A 6 way unit is also available for 19" mounting with a 2U high anodised front panel (6 way F P). COVER A cover is available for mounting over the switch to avoid unwanted power failure. Length mm Type 4 way 345 A 640-553950E 6 way 463 A 640-553951C 8 way 583 A 640-553952A 12 way 823 A 640-553953K 6 way F P 19"(482.6mm) A 640-553954H Cover - D 640-553967K MOUNTING BRACKETS FOR SCHUKO & SWISS SOCKETS Note: All vertically mounted power distribution panels (PDPs) require mounting brackets. The PDP type letter relates to the bracket options available. Type A PDPs will require a version 1, 2 or 3 bracket. Can be vertically mounted only. Type C PDPs can be mounted either horizontally on the 19" mounts or vertically. 19" Horizontal mounting - version 4 mounting bracket. Vertrical mounting - requires both a version 5 pair of brackets plus a version 1, 2 or 3 bracket. Type D PDPs mount directly onto the 19" panel mounts and do not use any mounting brackets. MOUNTING BRACKETS VERSION 3 VERSION 4 VERSION 4 & 5 VERSION 5 MOUNTING BRACKETS 3 Versions are available for Type A PDPs VERSION 1. Vertical mounting bracket which allows the PDPs to be fixed either directly to the vertical of the IMRAK or alternatively to the panel mounting angle. Supplied in pairs with fixings. VERSION 2. Bayed mounting brackets which allow the PDPs to be fitted in what is otherwise wasted space between two adjacent racks. Supplied in pairs with fixings. VERSION 3. Side mounting brackets which allow the PDPs to be fitted in the space behind the panel mounting - hence 19" equipment can be inserted past the PDP without problems. Supplied in pairs. VERSION 4- The 19" style allows Type C panels to be mounted in any 19" rack. VERSION 5 - Vertical adaptor brackets allow Types B & C panels to be vertically mounted. Note: These brackets should be used in conjunction with IMRAK PDP brackets (versions 1, 2 & 3). when mounted in a rack. Version 1 Vertical mounting 802-561050A Version 2 Bayed mounting 802-561051K Version 3* Side mounting 802-561052H Version 4 19" 802-552996H Version 5 Vertical 802-553007J *Note: With this type of mounting bracket, a pair of panel mount supports to suit the rack depth are required.
GENERAL CABINET ACCESSORIES FRENCH SOCKETS, VERTICAL MOUNTING These metal bodied units are available with either an illuminated switch or as a non-switched version. Both units are fitted with an external earthing position and the unit comes complete with 3 metres of cable and a French plug. Note: the unit does NOT contain a fuse. The units can be bolted directly to the IMRAK verticals or alternatively can be bolted vertically to the 19" panel mount angles with the use of a mounting bracket (640-912784H). The units are 67mm wide and 48mm high. Total length 5 way switched 467mm 640-912802K 8 way switched 689mm 640-912803H 12 way switched 911mm 640-912804F 5 way non-switched 467mm 640-912798H 8 way non-switched 689mm 640-912799F 12 way non-switched 911mm 640-912800C Mounting bracket - 640-912784H FRENCH SOCKETS 19" MOUNTING OR VERTICAL MOUNTED These metal bodied units are available with either an illuminated switch or as a non-switch version. Both units are fitted with an external earthing position and the unit comes complete with 3 metres of cable and a French plug. Note; the unit does NOT contain a fuse. The units can be bolted vertically onto the IMRAK 'panel mount angles' using the 'vertical mounting bracket' or alternatively can be bolted across the 19" panel mounts horizontally with the use of the '19" mounting bracket. Total length 4 way switched 407mm 640-912801A 4 way non-switched 407mm 640-912797K 19" mounting bracket - 640-912732E Vertical mounting bracket - 640-912784H 2U RACK MOUNTED FIRE PROTECTION UNIT (FPU) Protecting key equipment or the local area from fire should be of prime importance. This is specially true for mission critical equipment or for environments which are not covered by a premises fire protection system. The rack mounted FPU continuously monitors for smoke within the rack in the advent of a fire it cuts the power to the rack, activates alarm systems and extinguishes the fire. The incoming mains power to the rack is routed through the FPU via a 10 amp IEC female socket. The output power is also via 10 amp IEC sockets. Within the FPU are two optical smoke detectors. Two detectors are necessary because in racks, with forced air cooling, the exhaust air flows can be very laminar and two detectors are required to ensure all the exhaust air is monitored. At 3% obscurative the optical detectors trigger the protection system. Twin 10 amp relays cut power to the outlet sockets, thereby removing the source of heat and any cooling fans which otherwise would continue to expel smoke into the external environment. The audible and visual alarms operate and the alarm contacts, used for remote monitoring change state. The gas filled fire extinguisher also automatically operates flooding the rack with the extinguishant FM200. The unit is reset by a switch on the units front panel. Note, the FPU should always be mounted in the top 2U of the rack. 2U Fire protection unit 640-558051C Replacement extinguisher 640-558052A LIGHT This magnetically attached light is ideal for use in any environment with steel racks as it comes complete with a powerful magnet at the rear allowing easy fixing in horizontal or vertical formats. Its modern styling includes a high output, lower power consumption (11 watts) U shaped fluorescent tube which combine to give long tube life. If required the light can be fixed with screws to prevent unauthorised removal. This unit is not supplied with a plug and lead, the plug and lead should be ordered separately. Voltage rating Dimensions : 230V : 351 x 65 x 62mm MAGNETIC LIGHT SCHUKO VERSION A Schuko socket is moulded into the front face of the light. MAGNETIC LIGHT UK VERSION A 13 amp power socket is moulded into the front face of the light. LIGHT AND LEADS Light, Schuko version 802-562179A *Light, UK version 802-563580F 1,8m lead, schuko plug 802-562180E 2,0m lead, 13 amp plug 802-561559G * Commercial product only 57
NETWORKING SOLUTIONS FIBRE OPTIC 19" SHELVES These successful shelves have been further improved by re-engineering. Their primary function of efficient installation and termination of fibre optic cables has been made ever more flexible. FEATURES 1U / 2U height, 218mm / 362mm deep Flexible recessing 0 to 75mm Easy configuring Full range of accessories Complete cable management Supplied with all fixings including 19" mount requirement Rear panel with matrix of knockout with hole diameters 13mm, 16mm and 24.5mm for the mounting of various sized cable glands 19" fixed or slide mounting options (Recommended slides are 98-43211G & 98-43212C) Material : Zintec coated steel Finish : Pale grey RAL 7035 Splice Cassette : Polyester plastic The products can be configured (n) to provide complete kits for delivery FIBRE OPTIC 19" FRONT PANELS The flexibility of pre punched front panels or connector plates to allow mixed technology is still available. FEATURES Pre punched ST & SC Modular options for SMA/FDDI and FC/PC 19" conversion kit 1U SHELF 1U x 218mm 971-250745K 1U x 362mm 971-250747F 1U mtg kit for PKI cassette 972-250766E 1U mtg kit for BICC cassette 972-252990A 2U SHELF 2U x 218mm 971-250746H 2U x 362mm 971-250748D 2U mtg kit for PKI cassette 972-250767C 2U mtg kit for BICC cassette 972-252991K 1U FRONT PANELS 8W ST 971-250749B 12W ST 971-250750F 16W ST 971-250751D 24W ST 971-250752B 16W Single SC 971-258928F 16W Double SC 971-258929D Module Connector Panel 971-250756E 19" kit 971-250754J Plain Front 971-250758A 2U FRONT PANELS 48W ST 971-250753L 32W Single SC 971-258930H 32W Double SC 971-258931F Module Connector Panel 971-250757C 19" kit 971-250755G Plain Front 971-250759K MODULES 8W ST 960-233861L 8W SMA 960-233860B 2W FDDI 960-239728E 8W FC/PC 960-233991J BLANK 960-239021C 58
WALL CABINET FOR FIBRE APPLICATIONS NETWORKING SOLUTIONS The improved slimline cabinet can now be used for fibre applications, using the cassette kits, front panels & 19" conversion kits shown on the opposite page. The products can be configured (N) to provide complete kits for delivery: EG 960-254426A x 1 cabinet 972-250762B x 1 2 splice cassette kit 971-250752B x 1 24 way ST front panel 971-250754J x 1 19" conversion kit for front panel 960-249737J x 2 cable gland 972-250919F x 1 pack of cable clips Dimensions H W D 500mm x 335mm x 115mm Material:1.2 Zintec coated steel Colours: Pale grey RAL 7035 Base Dark grey RAL 7037 Door Cable glands Cabinet 960-254426A Earth kit 801-231543C FIBRE OPTIC SHELF AND WALL MOUNTED CABINET ACCESSORIES Pack Qty. Anchor stud 1 972-250911L Cable gland (size 2,3 to 6,7mm) 1 960-249741G Cable gland (size 4,8 to 8,0mm) 1 960-249737J Cable gland (size 7,0 to 12,0mm) 1 960-249739E Heatshrink gland (size 10,0 to 27,0mm) 1 960-233443G Two way branching kit 1 960-233853K Four way branching kit 1 960-233854H 2,5mm nylon tube 10M 960-233855F Cable clip 20 972-250919F Fibre field label 10 960-238875H Fusion splice sleeve 100 960-227227K ST blanking plug 10 960-238501E SMA blanking plug 10 960-238502C BICC cassette 1 960-237776D PKI cassette 1 960-249375F Fibre cable tidy 1 972-256727G Anchor stud Two way branching kit ST ADAPTORS CABLE TIDY Suitable for both multimode and single mode connections Adaptor possesses the key-way and posts for bayonet type connection Precision alignment reduces insertion loss Bayonet mount ensures repeatability of connections ST ADAPTORS ST adaptor 960-227232F 59
NETWORKING SOLUTIONS 110 TOWER UNIT A modular Tower unit has been developed for the mounting of 110 blocks and cable management blocks. The tower can either be wall mounted or installed into a 600, 800 or 1200 wide IMRAK and is available to suit 12U, 17U, 22U, 27U, 32U, 37U, 42U and 47U heights IMRAK's. The maximum number of towers that can be installed across the width of IMRAK is 2 for 600mm wide, 3 for 800mm wide and 5 for 1200mm wide. The cross members mount from the panel mount supports. Depending on configuration of tower and rack, additional panel mount supports may be required. To specify the IMRAK racking system refer to the IMRAK Section. Mild steel Painted grey RAL 7035 CONTENTS OF KITS Tower kit : 1 Tower unit and Fixings Cross Member kit : 2 Cross members and Fixings Cable restrainers : 1 Pair and Fixings Cable trough kit : 1Trough and Fixings 12U IMRAK Tower (200 Pair) 961-554476A 17U IMRAK Tower (300 Pair) 961-554477K 22U IMRAK Tower (500 Pair) 961-554478H 27U IMRAK Tower (600 Pair) 961-554192D 32U IMRAK Tower (800 Pair) 961-554193B 37U IMRAK Tower (900 Pair) 961-554194L 42U IMRAK Tower (1000 Pair) 961-554195J 47U IMRAK Tower (1200 Pair) 961-554196G IMRAK 600mm wide cross member 961-554197E IMRAK 800mm wide cross member 961-554198C IMRAK1200mm wide cross member 961-554199A Cable restrainers 961-554200J Cable Trough 961-554525C 110 PDS PANEL Designed for 19" mounting, these panels will support 2 off 100 pair wiring blocks and 2 off cable tidy on 4U panels and 2 off 100 pair blocks on 2U panel. The recessed panels allow forward mounting of the panel mounts without interference from the cabinet door. Mild steel Painted grey RAL 7035 110 PDS PANEL 4U flat 961-553168F 2U recessed 961-508243A 4U recessed 961-508244K Recess is 100mm Note: Physical height of tower is approx 3U less than height of rack. 60