Pipe and Bolt Threading Machine Main Drive Components 0 0 0 0 0 0 0 0 0 Pump Bracket Screw () Washer (0) Screw Centering Jaw Set Centering Head Back Plate Top Cover Die Head Decal (Not Shown) 00 Screw / - 0 x / () 0 00 Set Screw / - x / () Set Screw / - x / () 0 Scroll Rear Bearing 0 Washer Rear Side Plate Screw / - 0 x / 0 Grease Fitting () Screw / - x / () 0 Lock Washer / 0 0 Washer / Base Belt Tensioner 0 Nut / - () 0 Washer / () See Service Notes 00 Lock Washer / () 0 Oil Pump Set Screw / - x 00 Chuck Jaw Set 0 Roll Pin / x / Jaw Insert Set Front Bearing Jaw Insert Set F/Coated Pipe Gear Box Assy. 0 Self-Tapping Screw ( Req. f/g.s.) 0 0 Motor Bracket 0 Front Side Plate V-Belt Gear Box Pulley 00 Lock Washer / () 0 Pinch Point Boss ( Req. f/g.s.) Lock Nut / - 00 Inlet Hose 00 Grommet Output Hose Spacer 00 Key 0 Bolt / - x / 0 Rivets () Motor Pulley (0 Hz) Chuck Cap 0 Motor Pulley (0 Hz) 0 0 Safety Plate Drive Gear/Spindle Assy. Screw / - x / () Bottom Cover Screw 0 - () 0 Handwheel Set of Cover Plates Motor w/capacitor 0V, 0 Hz Jam Nut / - Motor w/capacitor 0V, 0 Hz Tube Insert () Motor w/capacitor 0V, 0 Hz 00 Compression Nut Motor w/capacitor 0/0V, 0 Hz 00 Ferrule 0 Motor w/capacitor 0V, 0 Hz GS Union 0 Shoulder Bolt Tie Down Strap 0 Pinion Guard 0 Screw 0 - x / Scroll 0 Shifter Knob
Pipe and Bolt Threading Machine Carriage and Chip Pan 0 0 0 0 0 Carriage Assembly (Includes Ref. #-, 0-,,,,,, -) 0 Rail Plug () 0 Bolt / - x / () Rear Rail Guide Block () Sine Bar Spacer 0 Sine Bar Sine Bar Cover Assembly Guide Block Spring () 0 Roll Pin () 0 Carriage (Includes Ref. #) Sine Bar Return Spring Washer #0 () Guide Bar Screw #0 - x / () Front Rail Oil Supply Clamp Sine Bar/Pinion Shaft () Supply Line Fitting Drip Plate 0 Die Lubrication Tube Sine Bar Pinion 0 Carriage Handwheel Carriage Pinion () Stud () Roll Pin / x / () 0 Draw Tray Assembly 0 Insert Assembly Washer Seal Washer 0 Bulk Head Fitting Tubing Screen Assembly Screw #0 - x / Chip Pan Hanger Assembly Chip Pan Bracket () 00 Lock Washer / () Screw / - x / () Hex Nut / - 0 Washer 0 Drain Plug Drain Plug (Rubber-Early Style) Ball Detente Lock Nut / - () Pin 0 Spring 0 Handwheel Shaft Lock Washer 0 Washer Screw 0 Spring Washer 0 0 Latch Spiral Pin 0 Handwheel Kit
Pipe and Bolt Threading Machine ML Oil Pump 0 ML Oil Pump Pump Valve Body Compression Fitting () * Gasket (Set of ) * Valve Retainer Assy. Gerotor Housing w/bearing * O-Ring Sleeve Bearing Gerotor Set Pump Cap w/seal 0* Oil Seal 0 Soc. Hd. Cap Screw / - 0 x 0 Lock Washer / * ML Service Kit * * * 0* Note: Ref. Sleeve Bearing used on older Geroter Housings, not required on new pumps. * Indicates Part is Included in Service Kit. See Service Note No. Pipe Cutter Pipe Cutter Screw Handle 0 Ball Bearing Cutter Frame Roll Housing Groove Pin Groove Pin () Cutter Wheel Roll () Roll F/Coated Pipe ( per set) 0 Wheel Pin 0 0 Groove Pin 0 No. Reamer Assembly Reamer Assembly 0 Reamer Arm Reamer Blade / - 0 Shoulder Bolt 0 Groove Pin 0 Pivot Block Groove Pin ()
Pipe and Bolt Threading Machine Gear Box 0 0 0 * * * 0 Gear Box Assembly 0 Screw / - x / () 0 Fixed Gear Cluster Assembly Freeze Plug Snap Ring () 0 Screw / - x / () Snap Ring Rear Output Bearing 0 Washer / () Shift Cluster Key 0 Thrust Washer 0 Spiral Pin Output Pinion Key 0 Input Shaft Assembly Front Output Bearing Input Pinion Key Wire Ring Output Shaft Wire Ring () Dowel Pin () 0 Front Input Bearing Shifting Fork st Input Gear Gear Box Snap Ring Output Pinion Gear Cluster Shift Gear Snap Ring 0 Retaining Ring Input Rear Bearing 0 Rings Set of Rear Bearing Woodruff Key () * st Gear Constant Speed * Constant Speed Shaft * Large Constant Speed Gear 0 Stop Nut / - () Shift Slide 0 Shifter Knob Shifter Detente Spring 0 Spacer 0 Front Constant Speed Bearing Steel Ball Shift Slide Sleeve Bearing 0 Grease ( lb. can) 0 Constant Speed Assembly See Service Notes *When replacing early style parts, using square keys, a complete shaft assembly (Ref. No. ) should be used.