FORD Tourneo Connect 07/08 >> Transit Connect 07/08 >> For vehicles with and without trailer preparation! Part No: FR-09-07 Electric wiring kit for towbars / 7-pin / N / Volt / ISO 74 This electric kit has to be installed by a professional workshop or a suitable qualified person. The installation instructions must have been read and fully understood before the start of any installation. Please contact your wiring kit provider or the hotline shown in the footer should you need assistance! Make sure the vehicle is approved/homologated by the manufacturer to tow a trailer! Also please check that there is a definite compatibility between this vehicle and the electric kit! Following the installation of the electric kit, the fitting instructions should be kept together with the vehicle service document and vehicle handbook. The fitting instructions contain important information relating to the use and function of the towing kit as well as for any diagnostic or activation process, that might have to be repeated in the future (e.g. after the performance of a vehicle software update). All warranty claims will be forfeited if the electric kit or components contained therein are used incorrectly or modified. If a towing socket adaptor has been used to connect to the trailer or bike rack, this must be removed from the trailer socket once the trailer or bike rack has been disconnected. If the trailer or bike rack is not equipped with a rear fog lamp, depending on the towing vehicle type, the correct function of the towing kit cannot be guaranteed. In such cases, a rear fog lamp should be retro fitted. This towing electric kit will not be covered under warranty if any technical or electrical modifications or software updates have been performed by the vehicle manufacturer after the initial commissioning of the kit. That applies especially to modifications or updates which may cause malfunctions in the trailer socket or any other part of the trailer electrical equipment! Depending on the type of trailer module used in this electric kit, diagnostic interrogation with the vehicle s electrical system may be limited or will not function. The error memory inside the trailer module may not be able to be accessed by vehicle manufacturers diagnostic system. Error logs relating to the trailer electrical equipment, that may be generated in the vehicle manufacturers diagnostic system as a result of a test procedure, may be due to the incorrect installation of the towing electric kit or the false activation of the trailer module. We always recommend whenever possible, the following troubleshooting process: An analysis of the vehicle s error memory and possibly clearing of all faults before the start of the installation! Try disconnecting the trailer module from the towing harness and re-start the fault clearing process! If in doubt, limit the time for troubleshooting to a max of 0,5 hours and call our Technical Support Team! Please follow our instructions carefully and always test the towing electrics using a true lighting board or a specifically designed bulb tester. If an LED tester is used, ensure it is equipped with correct load resistors or malfunctions will occur! This instruction is subject to changes and we reserve the right to make changes to design, colour etc. All of the data and illustrations may not be an exact representation but the text contained in this instruction must be observed! /9
*********** **** --> Righ t S TE /** W t t Part No: ********* C U C M M U A T X B G 5x C U x x x x x x x x x x 0x U5 micro II fuse mini fuse U6 All models Without trailer preparation All models With trailer preparation Option B, 8-, 5-7 -4 Option A /9
+ + SYMBOL EXPLANATION Left (58-L) respectively Right (58-R) tail light V Cigarette lighter / accessory socket 54 STOP Stop light (54) / high mounted, third stop light (54) Loudspeaker / buzzer L Turn signal indicator left Park Distance Control R Turn signal indicator right Switch / source of function Rear fog light(s) Connect together Reverse Reversing light(s) Disconnect 0+ 5+ Permanent power supply / pin socket, chamber 9 Charging wire for trailer battery / pin socket, chamber 0 Look at / See further information Look carefully at selected area Trailer / trailer recognition Present / Occupied / OK B+/0 Permanent current power supply Not present / Not occupied / Not OK Ground or Earth () Acoustic indication Ground connection battery terminal lug Attention / important advice Positive connection battery terminal lug Fuse / fuse capacity 0 Ampère TOOLS C o C o ATTENTION! The vehicle's cooling capacity may have to be increased when retrofitting a trailer coupling! You must observe the manufacturer's instructions!!! Note: It may be necessary to check if this vehicle has a stored radio code before disconnecting the battery! Code : ATTENTION! In order to avoid mal-functions and damage to the vehicle s electrical system the earth terminal must be disconnected from the vehicle s battery before starting work! Both the trailer module and the vehicle s control unit for the electrical system can be damaged during work on the data bus connections if the battery is not disconnected! Please pay attention to the manufacturer s instructions when disconnecting and reconnecting the vehicle s battery! /9
T X SEAL WITH SILICONE. 4/9
4!Attention: Ad-Blue tank may obscure grommet! 5 X SOCKET CONNECTION DIN/ISO 74 Pmax L -7 R STOP /L / 4/R 5/58-R 6/54 7/58-L W W W 5W xw 5W Yellow Blue White Green Brown Red Black 6 X! 7! 5/9
M M 4 M 8 M 0 mm G 9 6/9
Grey 6-pin Blue/Red Grey/Purple 54 STOP B Grey/Purple 54 STOP 4 B A 54 STOP 0 mini fuse mini fuse Red/Blue U Red/Blue 7/9
Option Pin, B+/0 Grey -pin Black 4-pin + 5 4 Vehicle with trailer preparation, B+/0 available Option Pin, B+/0 Grey -pin Black 4-pin 4 + 5 4 Vehicle with trailer preparation, without B+/0 Option Grey -pin Black 4-pin 5 8 + 4 Vehicle without trailer preparation 8/9
Option Grey -pin U Black 4-pin C C Option U Pos. 47 40A 5 Pos. 47 40A Pos. 47 40A Ford Spare Part Pos. 47 40 Amp. 4 9/9
Option & Option B Option A Option A Option B! Option B only if! 5 0/9
Option & Option A Option B 5 4 6 With glove box! Option & 7 /9
Without glove box! Option & 5x 8 Option Black 4-pin C C U C 4 9 U U /9
Option Option A Option B Cut to correct length! 50 mm micro II fuse 4 U5 U6 0 Option F5 U6! Important! Please do not mount the fuse tap and its wiring output in the other direction! /9
Option C C C U U Option A 4 Option B 4/9
Option 00 mm Cut to correct length, if necessary! Black CAN-Data Wire Grey/Orange CAN high! Violet/Orange CAN low Important! Please note informations in picture! Black CAN high Yellow CAN low Black CAN high Grey/Orange Grey/Orange Grey/Orange Violet/Orange Yellow CAN Low Violet/Orange Violet/Orange 5/9
Option micro II fuse U5 U6 F5! Important! Please do not mount the fuse tap and its wiring output in the other direction! 4 Optional Reverse! MAX = W B M Reverse G A Pink A Reverse S socket 5 6/9
! Code : 6 Set up trailer operation! Please effect FDRS online coding as follows: Connect with FordEtis Dealer registration Vehicle : enter VIN Vehicle software Changes and Upgrades Configuration of towbar Select Genuine Ford Module 7 Ford Diagnose If the following control units / functions are installed, they must be configured manually on trailer operation: PAM SODL SODR FCDIM Optional Trailer Simulator for 7- and -pin Sockets 8 L R Reverse 54 STOP 9 7/9
C RPMx000 H 6:00 AM 6 F 80 Driving Aids 60 00 00 0 40 60 40 80 80 0 60 00 40 0 0 0 40 40 OK MENU 60 km/h 6666 miles 500 miles 60 0 /! L R 0 4 5 6 7 8 P LED L R 0 Optional Adapter socket 7-pin -pin 8/9
*********** **** --> Righ t S TE /** W t t Part No: ********* 4 9/9