Way/ 2 and 3 Position Four ported valves are generally used to operate double-acting cylinders or actuators. They have four or five pipe connections, commonly called ports: One pressure inlet. Two cylinder ports providing pressure to the double-acting cylinder or actuator. One or two outlets to exhaust pressure from the cylinders. In a de-energized position, pressure is connected to one cylinder port; the other port is connected to the exhaust. In an energized position, pressure and exhaust are reversed. Four ports means less piping is required. With five ports, independent speed controls can be mounted in each port. Three Types of Constructions Apply: Single Solenoid When the solenoid is energized, the valve shifts, then returns to the original position when de-energized. and 5 Ported Valves Flow Diagrams De-Energized Press. Press. Cyl. B Cyl. B Energized Exh. Exh. Cyl. A Cyl. A Dual Solenoid When one solenoid is energized, the valve shifts, then returns when the other solenoid is energized. They may be energized momentarily or continuously, but never concurrently. Some valves, both single and dual solenoid, may change position on loss of fluid pressure. Single Air Operator When the operator is pressurized, the valve shifts, then returns when the pressure is removed. See Engineering Section for further details. Standard and Optional Features: Solenoid valves are supplied, as listed, with either Red-Hat II molded epoxy solenoids or Red-Hat solenoids with metal enclosures (except for Series 801). Red-Hat II valves are identified by the letter G or H in their catalog numbers; e.g., 83G27. Many optional features may be added to your valves; e.g., high-temperature Class H molded coils and manual operators. See the Optional Features Section for details. Typical Ported Single Solenoid Dual Solenoid Cyl. B Press. Exh. Press. Exh. De Energized Solenoid A Last Energized Cyl. B Cyl. B Cyl. A Cyl. A Press. Exh. Energized Cyl. A Exh. Press. Exh. 2 De Energized Cyl. B Cyl. A Exh. Press. Exh. 2 Energized Cyl. B Cyl. B Cyl. B Cyl. A Press. Exh. Solenoid B Last Energized Cyl. A Cyl. A Typical 5 Ported Single Solenoid Dual Solenoid Exh. Press. Exh. 2 Solenoid A Last Energized Cyl. B Cyl. A Exh. Press. Exh. 2 Solenoid B Last Energized Series General Description (NPT) Page Number 830 Air Only 1/".01 832 General Service 1/" and 3/8.05 83 Piston/Poppet 1/" 1".07 835 Compact General Service 1/".09 801/802 Miniature Slide 1/8" and 1/".11 8551 Stainless Steel 1/".15 Directional Control.17.00
qwer Direct Acting Air-Only Solenoid Valves Aluminum Body In-Line, Sub-Base, and Group Mounted 1/" NPT E B A P /2 830 Features Air only design for cylinder control. Up to eight single and dual solenoid valves, in any combination, can be manifolded. Sub Base constructions have separate cylinder connections and common pressure and exhaust connections at each end. Can be assembled in the field by simply inserting tie rods through holes in base. Group Mounted constructions have common pressure connections at each end and separate cylinder and exhaust connections. Can be factory assembled or grouped in the field with strong snap on clamps, supplied. Construction Body Disc Core Tube Core and Plugnut Core Spring Shading Coil Seals Miscellaneous Electrical Standard Coil and Class of Solenoid Enclosures Valve Parts in Contact with Fluids Hard Anodized Aluminum Standard: Red Hat II Watertight, Types 1, 2, 3, 3S,, and X; Red Hat Type 1. Optional: Red Hat II Explosionproof and Watertight, Types 3, 3S,, X, 6, 6P, 7, and 9 (For 830G1 and 830G2 only); Red Hat Types 3,, X, 7, and 9. (To order, add prefix EF to catalog number.) See Optional Features Section for other available options. PE 305 Stainless Steel 30F Stainless Steel 302 Stainless Steel Copper NBR PA, CA Watt Rating and Power Consumption Spare Coil Part No. AC General Purpose Explosionproof DC Watts Watts VA Holding VA Inrush AC DC AC DC F 10.5 2 65 6982 6982 F 19.7 16.7 36 85 6982 66611 6982 66611 F 10.1 25 70 238610 23861 F 22.6 17.1 0 93 238610 238710 23861 23871 Standard Voltages: 2, 120, 20, 80 volts AC, 60 Hz (or 110, 220 volts AC, 50 Hz). 6, 12, 2, 120, 20 volts DC. Must be specified when ordering. Other voltages available when required. % ^ ) Nominal Ambient Temperature Ranges: AC: 32 F to 125 F (0 C to 52 C) DC: 32 F to 77 F (0 C to 25 C)(10 F/0 C occasionally) Leakage: Break in leakage rate of 2 SCFH is reduced to a very slight amount as the valve wears in. Approvals: CSA certified. AC is UL listed as General Purpose Valve. Red Hat II meets applicable CE directives..01 R1
830 Specifications (English units) Cv Flow Factor Specifications (Metric units) Max. AC SINGLE VALVE CONSTRUCTION - Single Solenoid Operating Pressure Differential (psi) Max. DC Max. Fluid Temp. F Aluminum Body Air-Inert Gas Air-Inert Gas AC DC Catalog Number AC DC 1/ 5/6.10 150 100 130 95 830G1 17.1/F 22.6/F SINGLE VALVE CONSTRUCTION - Dual Solenoid 1/ 5/6.10 150 100 10 95 830G2 10.1/F 22.6/F GROUP MOUNTED CONSTRUCTION - Single Solenoid 1/ 5/6.10 150 100 10 95 830A3 16.7/F 19.7/F GROUP MOUNTED CONSTRUCTION - Dual Solenoid 1/ 5/6.10 150 100 10 ➀ 95 ➀ 830A8 10.5/F 19.7/F SUB-BASE MOUNTED CONSTRUCTION - Single Solenoid 1/ 5/6.08 150 100 10 95 830A 16.7/F 19.7/F SUB-BASE MOUNTED CONSTRUCTION - Dual Solenoid 1/ 5/6.08 150 100 10 ➀ 95 ➀ 830A5 10.5/F 19.7/F Notes: ➀ Rating shown for individual mounted valves; when group mounted, maximum UL allowable fluid and ambient temperature is 86 F. (mm) Kv Flow Factor (m3/h) SINGLE VALVE CONSTRUCTION - Single Solenoid Max. AC Operating Pressure Differential (bar) Max. DC Max. Fluid Temp. C Aluminum Body Air-Inert Gas Air-Inert Gas AC DC Catalog Number AC DC 1/ 2.0.09 10 7 5 35 830G1 17.1/F 22.6/F SINGLE VALVE CONSTRUCTION - Dual Solenoid 1/ 2.0.09 10 7 0 35 830G2 10.1/F 22.6/F GROUP MOUNTED CONSTRUCTION - Single Solenoid 1/ 2.0.09 10 7 0 35 830A3 16.7/F 19.7/F GROUP MOUNTED CONSTRUCTION - Dual Solenoid 1/ 2.0.09 10 7 0 ➀ 35 ➀ 830A8 10.5/F 19.7/F SUB-BASE MOUNTED CONSTRUCTION - Single Solenoid 1/ 2.0.07 10 7 0 35 830A 16.7/F 19.7/F SUB-BASE MOUNTED CONSTRUCTION - Dual Solenoid 1/ 2.0.07 10 7 0 ➀ 35 ➀ 830A5 10.5/F 19.7/F Notes: ➀ Rating shown for individual mounted valves; when group mounted, maximum UL allowable fluid and ambient temperature is 30 C..02 R1
830 Dimensions: inches (mm) Note: Dual solenoid shown dotted in. SINGLE VALVE CONSTRUCTION - SINGLE AND DUAL SOLENOIDS SUB-BASE MOUNTED SINGLE AND DUAL SOLENOID CONSTRUCTION.03 R1
830 Dimensions: inches (mm) Mounting Brackets Catalog Number With General Purpose Solenoid Enclosure When Manual Operator Is Used 830G1 Mounting Holes on Body Order Kit No. 206 737 830G2 Standard NA 830A3 Mounting Holes on Body Order Kit No. 206 55 830A Mounting Holes on Body NA 830A5 Mounting Holes on Body NA 830A8 Standard when factory assembled, but must order Kit No. 206 55 for individual valves. NA NA Not Available. SUB-BASE MOUNTED CONSTRUCTION (Shown as Group Mounted) GROUP MOUNTED CONSTRUCTION - DUAL SOLENOID GROUP MOUNTED CONSTRUCTION SINGLE SOLENOID.0 R1
qwer Direct Acting General Service Solenoid Valves Brass or Stainless Steel Bodies 1/" and 3/8" NPT E B A P /2 832 Features Direct acting operation and high flow construction. Direct acting, high flow slide style valve. Optional flow control regulates cylinder speed independently, in either direction. Mechanical detent on dual solenoids holds last position, even after loss of electric power, pneumatics or pressure. No Minimum Operating Pressure Differential required to shift valve. Dual solenoid operation: solenoid may be energized momentarily (1/10 second) or continuously. Mountable in any position. Construction Electrical Solenoid Enclosures Valve Parts in Contact with Fluids Body Brass 30 Stainless Steel Seals and Discs Core Tube Core and Plugnut Springs Shading Coil Sleeve Seats Standard Coil and Class of NBR and FKM 305 Stainless Steel 30F Stainless Steel 302 Stainless Steel / 17 7 PH Stainless Steel Watt Rating and Power Consumption Copper Standard: Watertight, Types 1, 2, 3, 3S,, and X. Optional: Explosionproof and Watertight, Types 3, 3S,, X, 6, 6P, 7, and 9. (To order, add prefix EF to catalog number.) See Optional Features Section for other available options. PA Graphite filled PTFE Spare Coil Part No. General Purpose Explosionproof AC VA VA Watts Holding Inrush AC AC F 16.1 35 115 272610 27261 F 20.1 5 10 272610 27261 Standard Voltages: 2, 120, 20, 80 volts AC, 60 Hz. 2, 110, 115, 220, 230 volts AC, 50 Hz. Other voltages are available when required. Note: No combination 120/60, 110/50 coil available. Must order either 120/60 or 110/50, etc. % ^ ) Dual Solenoid Nominal Ambient Temperature Ranges: Standard Class F insulation: 32 F to 125 F (0 C to 52 C) Optional Class H insulation: 32 F to 10 F (0 C to 60 C) Approvals: CSA certified. UL listed as General Purpose Valves. Meets applicable CE directives..05
832 Specifications (English units) Cv Flow Factor ➀ SINGLE SOLENOID CONSTRUCTION Specifications (Metric units) Operating Pressure Differential (psi) Air-Inert Gas Maximum AC Water Max. Fluid. Temp. F Brass Body Stainless Steel Body Lt. Oil @ 300 SSU AC Catalog Number Ref. No. Catalog Number Ref. No. 1/ 3/16.70 125 100 100 160 832G1 1 832G701 2 20.1/F 3/8 3/16.70 125 100 100 160 832G3 1 832G703 2 20.1/F DUAL SOLENOID CONSTRUCTION 1/ 3/16.70 125 125 125 160 832G20 3 832G720 16.1/F 3/8 3/16.70 125 125 125 160 832G22 3 832G722 16.1/F Notes: ➀ With built in flow control (Suffix "M"), the Cv is 0. and an 0.5 psi minimum operating pressure is required. (mm) Kv Flow Factor (m3/h) ➀ SINGLE SOLENOID CONSTRUCTION Operating Pressure Differential (bar) Maximum AC Air-Inert Gas Water Max. Fluid. Temp. C Brass Body Stainless Steel Body Lt. Oil @ 300 SSU AC Catalog Number Ref. No. Catalog Number Ref. No. AC 1/.8.60 9 7 7 70 832G1 1 832G701 2 20.1/F 3/8.8.60 9 7 7 70 832G3 1 832G703 2 20.1/F DUAL SOLENOID CONSTRUCTION 1/.8.60 9 9 9 70 832G20 3 832G720 16.1/F 3/8.8.60 9 9 9 70 832G22 3 832G722 16.1/F Notes: ➀ With built in flow control (Suffix "M"), the Kv is 0.38 and an 0.03 bar minimum operating pressure is required. Dimensions: inches (mm) Ref. 1, 2, 3, AC.06
qwer Pilot Operated Piston/Poppet Solenoid Valves Brass Body 1/" to 1" NPT B E B E A A P /2 P 83 Features Sturdy, solid construction. Piston operated poppet design provides high flow. Can use air or water for piloting control valves. Wide range of sizes and flow rates. Single or dual solenoid construction. Dual solenoid can be shifted with a momentary signal and remain in position even if electrical power is lost. Mountable in any position. Construction Body Seals and Disc Core Tube Core and Plugnut Springs Shading Coil Pilot Seat Cartridge and Disc-Holder Shaft Gasket Electrical Standard Coil and Class of Watt Rating and Power Consumption AC Solenoid Enclosures Valve Parts in Contact with Fluids Spare Coil Part No. DC VA VA Watts Watts Holding Inrush General Purpose Explosionproof F 10.6 6.1 16 30 238210 238310 23821 23831 F 11.6 10.1 25 50 238610 238710 23861 23871 F 22.6 17.1 0 70 238610 238710 23861 23871 Dual Solenoid Operation: Minimum coil on time for dual solenoid valves is 0.3 seconds on air service and 1.0 seconds on liquids. Caution: Do not energize both solenoids simultaneously. Brass NBR 305 Stainless Steel 30F Stainless Steel 302 Stainless Steel and 17 7PH Stainless Steel Copper Standard Voltages: 2, 120, 20, 80 volts AC, 60 Hz (or 110, 220 volts AC, 50 Hz). 6, 12, 2, 120, 20 volts DC. Must be specified when ordering. Other voltages are available when required. Standard: Watertight, Types 1, 2, 3, 3S,, and X. Optional: Explosionproof and Watertight, Types 3, 3S,, X, 6, 6P, 7, and 9. (To order, add prefix EF to the catalog number.) See Optional Features Section for other available options. CA Lead/Copper % ) Nominal Ambient Temperature Ranges: AC: 32 F to 125 F (0 C to 52 C) DC: 32 F to 10 F (0 C to 0 C) Approvals: CSA certified. Meets applicable CE directives. Important: A Minimum Operating Pressure Differential must be maintained between the pressure and exhaust ports. Supply and exhaust piping must be full area, unrestricted. ASCO flow controls and other similar components must be installed in the cylinder lines only. Loss of air pressure may allow valve to shift on dual solenoid constructions..07 R2
83 Specifications (English units) Cv Flow Factor ➀ Min. Air-Inert Gas Specifications (Metric units) Operating Pressure Differential (psi) Max. AC Max. DC Lt. Oil @ Air-Inert Water 300 SSU Gas Water Max. Fluid Temp. F Brass Body Lt. Oil @ 300 SSU AC DC Catalog Number Ref. No. AC DC Press. Exh. SINGLE SOLENOID 1/ 1/.80 1.0 10 150 125 125 125 125 125 180 150 83G70 1 10.1/F 11.6/F 1/ 1/.80 1.0 10 250 ➁ 250 ➁ 250 ➁ 250 ➁ 250 ➁ 250 ➁ 180 180 83G0 1 17.1/F 22.6/F 3/8 3/8 1. 2.2 10 150 125 125 125 125 125 180 150 83G72 2 10.1/F 11.6/F 3/8 1/.80 1.0 10 250 ➁ 250 ➁ 250 ➁ 250 ➁ 250 ➁ 250 ➁ 180 180 83G1 1 17.1/F 22.6/F 1/2 3/8 1. 2.2 10 150 125 125 125 125 125 180 150 83G7 2 10.1/F 11.6/F 1/2 3/8 1. 2.2 10 250 ➁ 250 ➁ 250 ➁ 250 ➁ 250 ➁ 250 ➁ 180 180 83G27 2 17.1/F 22.6/F 3/ 3/ 5.2 5.6 10 150 125 125 125 125 125 180 150 83G76 3 10.1/F 11.6/F 3/ 3/ 5.2 5.6 10 250 ➁ 250 ➁ 250 ➁ 250 ➁ 250 ➁ 250 ➁ 180 180 83G29 3 17.1/F 22.6/F 1 3/ 5.2 5.6 10 150 125 125 125 125 125 180 150 83G78 3 10.1/F 11.6/F 1 3/ 5.2 5.6 10 250 ➁ 250 ➁ 250 ➁ 250 ➁ 250 ➁ 250 ➁ 180 180 83G31 3 17.1/F 22.6/F DUAL SOLENOID ➂ 1/ 1/.80 1.0 10 250 200 125 125 125 100 180 120 83G 6.1/F 10.6/F 3/8 3/8 1. 2.2 10 250 200 125 125 125 100 180 120 83G80 6 6.1/F 10.6/F 3/8 3/8 1. 2.2 10 300 300 200 180 83G50 7 10.1/F 1/2 3/8 1. 2.2 10 250 200 125 125 125 100 180 120 83G82 6 6.1/F 10.6/F 3/ 3/ 5.2 5.6 10 300 300 200 125 125 100 180 120 83G5 8 10.1/F 10.6/F 1 3/ 5.2 5.6 10 300 300 200 125 125 100 180 120 83G56 8 10.1/F 10.6/F Notes: ➀ 25 psi (1.7 bar) minimum on light oil service. ➂ On 50 hertz service, the watt rating for the 6.1/F solenoid is 8.1 watts. ➁ For best results, do not use valve rated 250 psi (17 bar) on mainline pressure of less than 125 psi (9 bar). (mm) Kv Flow Factor (m3/h) ➀ Min. Air-Inert Gas Operating Pressure Differential (bar) Max. AC Max. DC Lt. Oil @ 300 SSU Air-Inert Gas Max. Fluid Temp. C Brass Body Lt. Oil @ 300 SSU AC DC Catalog Number Watt Rating / Ref. No. AC DC Press. Exh. Water Water SINGLE SOLENOID 1/ 6.69.86 0.7 10 9 9 9 9 9 81 65 83G70 1 10.1/F 11.6/F 1/ 6.69.86 0.7 17 ➁ 17 ➁ 17 ➁ 17 ➁ 17 ➁ 17 ➁ 81 81 83G0 1 17.1/F 22.6/F 3/8 10 1.2 1.89 0.7 10 9 9 9 9 9 81 65 83G72 2 10.1/F 11.6/F 3/8 6.69.86 0.7 17 ➁ 17 ➁ 17 ➁ 17 ➁ 17 ➁ 17 ➁ 81 81 83G1 1 17.1/F 22.6/F 1/2 10 1.2 1.89 0.7 10 9 9 9 9 9 81 65 83G7 2 10.1/F 11.6/F 1/2 10 1.2 1.89 0.7 17 ➁ 17 ➁ 17 ➁ 17 ➁ 17 ➁ 17 ➁ 81 81 83G27 2 17.1/F 22.6/F 3/ 19.5.80 0.7 10 9 9 9 9 9 81 65 83G76 3 10.1/F 11.6/F 3/ 19.5.80 0.7 17 ➁ 17 ➁ 17 ➁ 17 ➁ 17 ➁ 17 ➁ 81 81 83G29 3 17.1/F 22.6/F 1 19.5.80 0.7 10 9 9 9 9 9 81 65 83G78 3 10.1/F 11.6/F 1 19.5.80 0.7 17 ➁ 17 ➁ 17 ➁ 17 ➁ 17 ➁ 17 ➁ 81 81 83G31 3 17.1/F 22.6/F DUAL SOLENOID ➂ 1/ 6.69.86 0.7 17 1 9 9 9 7 81 8 83G 6.1/F 10.6/F 3/8 10 1.2 1.89 0.7 17 1 9 9 9 7 81 8 83G80 6 6.1/F 10.6/F 3/8 10 1.2 1.89 0.7 21 21 1 81 83G50 7 10.1/F 1/2 10 1.2 1.89 0.7 17 1 9 9 9 7 81 8 83G82 6 6.1/F 10.6/F 3/ 19.5.80 0.7 21 21 1 9 9 7 81 8 83G5 8 10.1/F 10.6/F 1 19.5.80 0.7 21 21 1 9 9 7 81 8 83G56 8 10.1/F 10.6/F Dimensions: inches (mm) Ref. No. ØD E F G H J K L N P W X Y Z Exhaust 1 ins. Ø.28.56 2.1 1.88.08 1.03 2.15 3.13.72 3.12.75 1.1 1.56.81 3/8 mm Ø7.1 1 61 8 10 26 55 80 18 79 121 36 0 21 3/8 2 ins. Ø.3.75 3.12 2.63.06 1.50 1.97 3.18.83 2.9 6.06 1.88 1.90.8 1/2 mm Ø8.6 19 79 67 103 38 50 81 21 75 15 7 8 21 1/2 3 ins. Ø.3 1.3 3.81 3.88.86 2.09 2.3.56 1.56 3.31 8.25 2.12 2.63 1.16 1 mm Ø8.6 3 97 99 123 53 59 116 39 8 210 5 67 30 1 ins. Ø.28.56 2.1 1.88.3 1.03 2.52 3.13.72 3.38.81 1.1 1.56.81 3/8 mm Ø7.1 1 61 8 110 26 6 80 18 86 122 36 0 21 3/8 6 ins. Ø.3.75 3.12 2.63.50 1.50 2.52 3.18.83 3.38 6.06 1.88 1.90.8 1/2 mm Ø8.6 19 79 67 11 38 6 81 21 86 15 7 8 21 1/2 7 ins. Ø.3.75 3.12 2.63.68 1.50 2.59 3.18.83 3.56 6.06 1.88 1.90.8 1/2 mm Ø8.6 19 79 67 119 38 66 81 21 90 15 7 8 21 1/2 8 ins. Ø.3 1.3 3.81 3.88 5.56 2.09 3.03.56 1.55.00 8.25 2.12 2.63 1.16 1 mm Ø8.6 3 97 99 11 53 77 116 39 102 210 5 67 30 1 Ref 1-3 Ref. - 8 Ref 1-8.08 R2
qwer Pilot Operated Compact General Service Solenoid Valves Brass 316 Stainless Steel Bodies 1/" NPT EB B A P EA /2 835 Features Compact valves for general service applications. Low cost, way valve when low flow is sufficient. Mountable in any position. Construction Electrical Watt Rating and Power Consumption Solenoid Enclosures Valve Parts in Contact with Fluids Body Brass 316 Stainless Steel Seals and Discs NBR and PA FKM, PA and UR Core Tube Core and Plugnut 305 Stainless Steel 30F Stainless Steel Springs 302 Stainless Steel Shading Coil Piston Copper Spare Coil Part No. Standard AC General Explosionproof Explosionproof Coil and Purpose (EF) (EV) Class of DC VA VA Watts Watts Holding Inrush AC DC AC DC AC DC F 11.6 10.1 25 50 238610 238710 23861 23871 2761 2771 Standard Voltages: 2, 120, 20, 80 volts AC, 60 Hz (or 110, 220 volts AC, 50 Hz). 6, 12, 2, 120, 20 volts DC. Must be specified when ordering. Other voltages are available when required. Standard: Watertight, Types 1, 2, 3, 3S,, and X. Optional: Explosionproof and Watertight, Types 3, 3S,, X, 6, 6P, 7, and 9. (To order, add prefix EF or, for Explosionproof Stainless Steel trim and hub on Brass Bodied valves, add EV to catalog number.) See Optional Features Section for other available options. PA % ^ ) Nominal Ambient Temperature Ranges: AC: 32 F to 125 F (0 C to 52 C) DC: 32 F to 10 F (0 C to 0 C) Approvals: CSA certified. UL listed as General Purpose Valve. EV835G81 solenoid only UL approved. Meets applicable CE directives. Important: A Minimum Operating Pressure Differential must be maintained between the pressure and exhaust ports. Supply and exhaust piping must be full area, unrestricted. ASCO flow controls and other similar components must be installed in the cylinder lines only..09 R2
835 Specifications (English units) Cv Flow Factor Pressure Exhaust Inlet Exhaust Min. Specifications (Metric units) Operating Pressure Differential (psi) Air- Inert Gas Max. AC Water Lt. Oil @ 50 SSU Air- Inert Gas Max. DC Water Max. Fluid Temp. F Brass Body 316 Stainless Steel Body Lt. Oil @ 50 SSU AC DC Catalog Number Catalog Number Ref. No. AC DC SINGLE SOLENOID 1/ 1/16 3/32.09.09 10 150 150 150 100 100 100 180 10 835G1 EV835G81 1 10.1/F 11.6/F SINGLE SOLENOID AIR-ONLY CONSTRUCTION - Exhaust to Atmosphere 1/ 1/16 3/32.09.09 10 150 100 180 10 835H3 2 10.1/F 11.6/F (mm) Kv Flow Factor (m3/h) Operating Pressure Differential (bar) Max. AC Air- Lt. Oil Inert @ 50 Gas Water SSU Air- Inert Gas Max. DC Max. Fluid Temp. C Lt. Oil @ 50 SSU AC DC Brass Body 316 Stainless Steel Body Catalog Number Catalog Number Ref. No. AC DC Pressure Exhaust Inlet Exhaust Min. Water SINGLE SOLENOID 1/ 2 2.08.08 0.7 10 10 10 7 7 7 82 0 835G1 EV835G81 1 10.1/F 11.6/F SINGLE SOLENOID AIR-ONLY CONSTRUCTION - Exhaust to Atmosphere 1/ 2 2.08.08 0.7 10 7 82 0 835H3 2 10.1/F 11.6/F Dimensions: inches (mm) Ref. 1, 2.10 R2
Pilot Operated Miniature Directional Control Valves Aluminum Body Sub-Base and Manifold Mounted 1/" NPT 2 5/2 3 801 1 802 5 Features Unique guillotine action with sliding, sealing member. Optional flow control regulates cylinder speed in either direction. Dual solenoid versions hold last position, even after loss of electric power. Dual solenoid operation: solenoid may be energized momentarily (1/10 second) or continuously. Air/inert gas service only. Durable and non sticking sealing method. Standard manual operator both momentary and maintained. Optional flow control provides adjustable Cv from 0.2 to 0.8. Construction Main Valve Body, Sub- and Manifold Base, End Caps Pilot Valve Body End Caps Seals Spool Electrical Solenoid Enclosures Valve Parts in Contact with Fluids Aluminum Molded CA Stainless Steel (non metering) Molded CA (metering) NBR (Carboxylated Nitrile) Molded CA Slide Graphite filled PTFE Flow Plate Core Tube Ceramic (alumina) 305 Stainless Steel Core and Plugnut 30F Stainless Steel Springs 302 Stainless Steel Watt Rating and Power Consumption Standard Coil and AC Spare Coil Part No. Class of DC VA VA Watts Watts Holding Inrush AC DC F 6.9 6.3 8.8 12.1 00125 00125 Standard Voltages: 2, 120, 20, 80 volts AC, 60 Hz (or 110, 220 volts AC, 50 Hz). 6, 12, 2, 120, 20 volts DC. Must be specified when ordering. Other voltages are available when required. Standard: Open Frame Solenoid. Optional: Watertight, Types 1, 2, 3, 3S,, and X. (To order, substitute with prefix WT.) Explosionproof and Watertight, Types 3, 3S,, X, 6, 6P, 7, and 9. (To order, substitute with prefix EF.) See Optional Features Section for other available options. % ^ ) Nominal Ambient Temperature Ranges: Standard Class F insulation: AC: 0 F to 135 F ( 18 C to 57 C) ( U and SC prefix) AC: 0 F to 10 F ( 18 C to 0 C) (optional WT or EF prefix) DC: 0 F to 77 F ( 18 C to 25 C) 801 Approvals: CSA certified. UL recognized components for U and SC prefix. With prefix WT, UL listed as a General Purpose Valve. Meets applicable CE directives..11 R2
801 802 Specifications (English units) Cv Flow Factor Specifications (Metric units) Main Line Supply Max. Pressure (psi) Fluid Molded Epoxy Open Frame Solenoid Air-Inert Gas Temp. F Sub-Base Mounted Manifold Mounted Max. Max. AC DC AC DC Catalog Number Ref. No. Catalog Number Ref. No. AC DC Min. SINGLE SOLENOID 1/ 1/.80 20 150 150 135 77 U801B101 2 U801B103 3 6.3/F 6.9/F DUAL SOLENOID 1/ 1/.80 20 150 150 135 77 U801B105 5 U801B107 6 6.3/F 6.9/F SINGLE AIR PILOTED 1/ 1/.80 20 150 150 135 135 802A101 8 802A103 9 (mm) Kv Flow Factor (m3/h) Main Line Supply Max. Pressure (bar) Fluid Molded Epoxy Open Frame Solenoid Air-Inert Gas Temp. C Sub-Base Mounted Manifold Mounted Max. Max. AC DC AC DC Catalog Number Ref. No. Catalog Number Ref. No. AC DC Min. SINGLE SOLENOID 1/ 6.69 1. 10 10 57 25 U801B101 2 U801B103 3 6.3/F 6.9/F DUAL SOLENOID 1/ 6.69 1. 10 10 57 25 U801B105 5 U801B107 6 6.3/F 6.9/F SINGLE AIR PILOTED 1/ 6.69 1. 10 10 57 57 802A101 8 802A103 9 Dimensions: inches (mm) Ref. No. A B C E F 2.73.60.80 1.02.3 ➀ 19 15 20 26 112 ➀ 3 X X.79.91.3 ➀ X X 20 23 112 5.73.60.80 1.02 X 19 15 20 26 X See drawings for dimensions not shown. ➀ Add.5 (13.7 mm) for metering. Note: "EF" and "WT" dimensions shown by dotted lines. IMPORTANT: Valve can be mounted in any position. Ref. 2.12 R2
801 802 Dimensions: inches (mm) Ref. 3 (Valve only) Ref. 5 Ref. 3 (Valve with required end brackets.) (See List Price Schedule for appropriate kit numbers.).13 R2
801 802 Dimensions: inches (mm) Const. Ref. No. A B C E F G H 6* X X.79.91 X X X X 20 23 X X X 8.73.60.80 1.02.1 3.5 ➁ 1.22 ➀ 19 15 20 26 10 88 ➁ 31 ➀ 9* X X.79.91 X 3.5 ➁ 1.22 ➀ X X 20 23 X 88 ➁ 31 ➀ See drawings for dimensions not shown. 1 Add.5 (13.7 mm) for metering. ➁ Add 1.07 (27.2 mm). Note: "EF" and "WT" dimensions shown by dotted lines. Male 1/2" connection on EF/WT coil, conduit connector provided. * For dimensions with required end brackets see Const. Ref. 3 IMPORTANT: Valve can be mounted in any position. Auxiliary Pilot Air Pressure (psig) Ref. 8 SINGLE AIR PILOTED VALVES Auxiliary Pilot Air Pressure vs. Main Line Air Pressure 120 100 80 60 0 20 0 20 0 60 80 100 120 10 160 Main Line Air Pressure (psig) Ref. 6 Ref. 9.1 R2
Features Compact spool valve with threaded port connections. All exhaust ports are pipable, providing better protection against harsh environments. Standard manual operator. DIN, Watertight and Explosionproof solenoids available. Single and dual solenoid constructions. Mountable in any position. Construction Body Spring Shading Coil Seals Core and Core tube End Covers Spool Internal Parts Electrical Standard Coil and Class of Solenoid Enclosures Valve Parts in Contact with Fluid Black Anodized Aluminum Phosphate treated black steel Copper NBR + PUR Stainless Steel/Brass 6/6 glass filled PA/FG Aluminum Zamak, Steel, CA, Aluminum Watt Rating and Power Consumption Spare Coil Part Number Enclosure Type DC Watts AC Watts VA Holding VA Inrush AC DC F SC 3 2.5 3.5 6 00125 00125 F EF 6.9 6.3 7 10.1 266762 270007 F WT 6.9 6.3 7 10.1 266763 270008 Standard Voltages: SC: 2, 120, 20 volts AC, 50 60 Hz; 12, 2, 120 volts DC. WT and EF: 2/50 60Hz, (120/60, 110 120/50)➀, (20/60, 220 20/50)➁ volts AC; 6, 12, 2, 120 volts DC. Notes: ➀ Order as 120/60, 110/50 ➁ Order as 20/60, 220/50 Standard: - Prefix SC = IP65 type DIN (open frame) per 62 WT= Combination General Purpose and Watertight Types 1, 2, 3, 3S,, and X EF = Combination Explosionproof and Watertight Types 3, 3S,, X, 6, 6P, 7, 9 CLASS 1, DIV. 1 (Groups A D) and CLASS 2, DIV.1 Type 9 (Groups E G) Pilot Operated Spool Valves Anodized Aluminum Bodies 1/ NPT Nominal Ambient Temperature Ranges: SC: AC/DC: 5 F to +10 F ( 15 C to 60 C) EF: AC: 5 F to +10 F ( 15 C to 0 C) DC: 5 F to +77 F ( 15 C to 25 C) WT: AC: 5 F to +10 F ( 15 C to 60 C) DC: 5 F to +77 F ( 15 C to 25 C) Note: For temperatures below 32 F (0 C) moisture free air must be used. Approvals: % ^ ) 3/2 5/2 SC: UL recognized component. EF: UL and CSA solenoid approval. WT: UL General Purpose valve. Meets applicable CE directives. Refer to Engineering Section for details. Option: Metering: order metering device pkg. of 20 pcs. Order kit number: 276790 002 *. NOTE: When mounting inline 8551 valves with WT & EF solenoids (6.3 & 6.9 watts), ASCO recommends using two (2) 1/8 thick washers under the valve body to provide clearance for the solenoid coil..15 R1 3 3 2 2 1 1 12 12 2 3 5 1 2 3 3/2 5/2 8551 5 1 1
3/2 5/2 8551 Specifications (English units) Cv Flow Factor Dimensions: inches PREFIX SC COIL/SOLENOID PREFIX WT + EF COIL/SOLENOID Pilot Pressure PORT 3 (EXHAUST) 2 X Ø 0.21 NOTE 2 3.69 Fluid Temp. F (for single and dual solenoid) Single Solenoid Dual Solenoid Ref. No. Catalog Number Min. Max. Min. Max. AC Max. DC Catalog Number 0.86 0.0 5.69 1.30 0.36 NOTE 3 PORT 1 (PRESSURE INLET) 3 X 1/ NPT Const. Ref. 1 SHOWN WITH OPTIONAL METERING DEVICE 1.26 1.77 PORT 2 (CYLINDER) 1.18 COIL ROTATABLE ( POSITIONS) 0.90 2.1 SCREW MANUAL OVERRIDE 1.O8 Const. Ref. No. AC DC OPEN FRAME DIN COIL 3 WAY 1/ 1/.86 30 150 5 10 10 SC8551A005MS 1 SC8551A006MS 3 2.5 3 WAY 1/ 1/.86 30 150 5 10 10 SC8551A017MS 2 SC8551A018MS 2.5 3 WATERTIGHT ENCLOSURE 3 WAY 1/ 1/.86 30 150 5 10 77 WT8551A005MS 1 WT8551A006MS 3 6.3 6.9 WAY 1/ 1/.86 30 150 5 10 77 WT8551A017MS 2 WT8551A018MS 6.3 6.9 EXPLOSIONPROOF ENCLOSURE 3 WAY 1/ 1/.86 30 150 5 10 77 EF8551A005MS 1 EF8551A006MS 3 6.3 6.9 WAY 1/ 1/.86 30 150 5 10 77 EF8551A017MS 2 EF8551A018MS 6.3 6.9.16 R1
20.5 10.5 5.3 2xÿ 0.209(ÿ5.3) 32 10.25 20.5 32 5 27.5 30 22.8 61.3 21.8 Dimensions: inches PREFIX SC COIL/SOLENOID PREFIX WT + EF COIL/SOLENOID PREFIX SC COIL/SOLENOID PREFIX WT + EF COIL/SOLENOID PORT 5(EXHAUST) PORT 1 (PRESSURE INLET) PORT 3 (EXHAUST) 2 X Ø 0.21 NOTE 2.11 0.86 0.0 0.81 0.81 6.177 1.26 0.36 1.30 0.0 5 X 1/ NPT NOTE 3 1.26 1.08 PORT 3 (EXHAUST) Const. Ref. 2 1.77 PORT 1 (PRESSURE INLET) 3 X 1/ NPT NOTE 3 Const. Ref. 3 1.08 1.26 1.77 PORT (CYLINDER) 1.18 COIL ROTATABLE( POSITIONS) 0.90 2.1 SCREW MANUAL OVERRIDE 1.18 0.858(21.8) 0.90 COIL ROTATABLE ( POSITIONS) PORT 2 (CYLINDER) 2.1 SCREW MANUAL OVERRIDE PORT 2 (CYLINDER) 3/2 5/2 8551 NOTE 2 3.69 2 X Ø 0.21 7.80.17 R1
3/2 5/2 8551 Dimensions: inches PREFIX SC COIL/SOLENOID PREFIX WT + EF COIL/SOLENOID PORT 5 (EXHAUST) PORT 1 (PRESSURE INLET).11 0.81 0.81 1.26 8.28 0.0 NOTE 2 NOTE 3 2 X Ø 0.21 5 X 1/ NPT PORT 3 (EXHAUST) Ref. 1.08 1.26 1.772 1.18 0.90 2.1 PORT (CYLINDER) PORT 2 (CYLINDER) 0.86 COIL ROTATABLE ( POSITIONS) SCREW MANUAL OVERRIDE.18 R1
qwer Single or Dual Solenoid Pilot Operated Stainless Steel Valves For In-line Applications 1/" NPT Single Solenoid Dual Solenoid 2 5 1 3 2 5 1 3 5/2 8551 Features Unique sealing technology combines hard T seals and flexible o rings for bubble tight shutoff, dirt resistance, and multimillion cycle life. Designed for use in corrosive atmospheres. Single or dual solenoids. Mountable in any position. Dual solenoid operation: solenoid may be energized momentarily (1/10 second) or continuously. Low Power and Intrinsically Safe constructions are avaiable. See Special Service Valve Section for details. Construction Body Seals and Discs Core and Plugnut Core Tube Springs Shading Coil End Covers Spool Internal Parts Electrical Standard Coil and Class of Solenoid Enclosures Valve Parts in Contact with Fluids Watt Rating and Power Consumption DC Watts Watts AC VA Holding 316 Stainless Steel NBR and PUR 30F Stainless Steel 305 Stainless Steel 302 Stainless Steel Copper 316 Stainless Steel 316 Stainless Steel Zamak, Steel, CA, Brass Spare Coil Part No. General Purpose Explosionproof (EV) VA Inrush AC DC AC DC F 11.6 10.1 25 50 238610 238710 2761 2771 Standard Voltages: 2, 120, 20, 80 volts AC, 60 Hz (115 230 volts AC, 50 Hz). 6, 12, 2, 120, 20 volts DC. Must be specified when ordering. Other voltages available when required. Standard: Watertight, Types 1, 2, 3, 3S,, and X. Optional: Explosionproof and Watertight, Types 3, 3S,, X, 6, 6P, 7, and 9. (For Stainless Steel trim and conduit hub, add prefix EV to catalog number.) See Optional Features Section for other available options. % ^ ) Nominal Ambient Temperature Ranges: AC: F to 125 F ( 20 C to 52 C) DC: F to 10 F ( 20 C to 0 C) Approvals: UL listed for General Purpose valve. UL recognized components for SC prefix (open frame version). Meets applicable CE directives. Optional "EV" solenoid is CSA certified and UL listed..15
8551 Specifications (English units) Operating Pressure Differential (psi) Specifications (Metric units) Single Solenoid Operating Pressure Differential (psi) Dual Solenoid Max. Max. Fluid Fluid Max. Temp. F Stainless Steel Max. Temp. F Stainless Steel Cv Flow Ref. Ref. Factor Min. AC DC AC DC Catalog Number No. Min. AC DC AC DC Catalog Number No. AC DC 1/ 1/.8 35 150 120 10 120 8551G53 1 20 150 120 10 120 8551G55 2 10.1/F 11.6/F Operating Pressure Differential (bar) Single Solenoid Operating Pressure Differential (bar) Dual Solenoid Max. Max. Fluid Fluid Kv Flow Max. Temp. C Stainless Steel Max. Temp. C Stainless Steel Factor Ref. Ref. (mm) (m3/h) Min. AC DC AC DC Catalog Number No. Min. AC DC AC DC Catalog Number No. AC DC 1/ 6.72 2 10 8 59 8 8551G53 1 1 10 8 59 8 8551G55 2 10.1/F 11.6/F Dimensions: inches (mm) SINGLE SOLENOID Ref. 1 DUAL SOLENOID Ref. 2.16