Kinze 3000 Series Row Unit Hydraulic Actuator PN: 2006428-ENG REV. A
Installation Overview Required Parts Part Number Qty * Description 4003011 1 HYDRAULIC ACTUATOR ASSY. (INCLUDES MOUNTING HARDWARE) 4003458 1 UPPER ACTUATOR BRACKET 4003418 1 SUPPORT PLATE FOR UPPER BRACKET 4003417 1 ADAPTER PLATE UPPER ACTUATOR BRACKET 4003476 1 LOWER ACTUATOR BRACKET 4003481 1 SUPPORT PLATE LOWER ACTUATOR BRACKET (LOWER RIGHT) 4003479 1 SUPPORT PLATE LOWER ACTUATOR BRACKET (UPPER LEFT) 4003480 1 SUPPORT PLATE LOWER ACTUATOR BRACKET (UPPER RIGHT) 4003514 1 ANTI-ROTATION BRACKET 2002478-0515 6 BUTTON HEAD BOLT 1/2 X 1-1/2 IN.** 2002225-50 6 HEX SERRATED FLANGE NUT 1/2 IN.** 2002021-50125 3 CARRIAGE BOLT 1/2 X 1-1/4 IN.** 2002071-50 3 FLAT WASHER 1/2 IN.** 2002055-50 3 LOCK NUT 1/2 IN.** 2002401-62175 4 HEX HEAD BOLT 5/8 X 1-3/4 IN.** 2002225-62 4 HEX SERRATED FLANGE NUT 5/8 IN.** 2002001-25075 2 HEX HEAD BOLT 1/4 X 3/4 IN.** 2002061-25 2 SPLIT LOCK WASHER 1/4 IN.** 4003523 1 UPPER ACTUATOR BRACKET EXTENSION*** 2002121-05525 3 CARRIAGE BOLT 1/2 X 5-1/4 IN.*** 2002071-50 3 FLAT WASHER 1/2 IN.*** 2002055-50 3 HEX LOCK NUT 1/2 IN.*** 4003484 2 ACTUATOR SPACER 1/4 IN. THICK**** 2002488-200 1 SHOULDER BOLT 5/16 X 2 IN. (USED WITH 1 SPACER)**** 2002488-225 1 SHOULDER BOLT 5/16 X 2-1/4 IN. (USED WITH 2 SPACERS)**** * Quantities listed are per row unit **Hardware can be located in Installation Kit P/N 4003498, 4003518, 4003497 ***Only required when parallel arm extension brackets are installed. 2
**** Required only when determined necessary by step 12 of this section. Installation Procedure 1. Raise planter enough that row units are resting on lower stops. Remove 2. Remove existing down force springs, or air bags and all brackets related to down force from each row unit (including air bag brackets). 3. Assemble lower actuator bracket support plates to lower actuator bracket. May work better to add lower support after upper supports have been loosely fastened to parallel arms). 4. Position bracket assembly between parallel arms. Loosely fasten upper support plates to existing mounting holes of upper parallel arms using (2) 1/2 x 1-1/2 in. button head bolts with serrated flange nuts. Loosely fasten lower right support plate to parallel arm using same fasteners. 5. Tighten 1/2 in. fasteners that secure lower actuator bracket support plates to parallel arms. Front of Planter Lower actuator bracket support plates Chamfer this edge as necessary to eliminate interference with weld Lower actuator bracket 3
Carriage Bolts 6. Install (3) 1/2 x 1-1/4 in. carriage bolts into lower holes of adapter plate. Do not install nuts. 7. Position support plate on top of adapter plate and install (2) 5/8 x 1-3/4 in. bolts through upper holes. 8. Flip adapter/support plate assembly over and loosely install serrated flange nuts onto 5/8 in. mounting bolts. Install nuts just flush with bolt threads. 4
9. Mount upper actuator bracket to adapter/support plate assembly. Secure with 1/2 in. lock nuts and flat washers. Do not use a flat washer on upper mounting bolt because there will not be enough bolt threads to engage nylon. 10. Tighten lock nuts. 11. Slide upper actuator bracket assembly onto front of row unit. Support plate is in front of row unit mounting plate and adapter plate is behind it. 12. Loosely install 5/8 x 1-3/4 in. bolts into lower mounting holes of adapter/support plates. 13. Align actuator mounting hole on upper bracket with actuator mounting hole on lower bracket. Actuator bases do not require perfect alignment but adjustment should be as close as possible. 14. Tighten all (4) 5/8 in. mounting bolts. An open-end wrench will be required for upper mounting bolts. 5
15. Mount anti-rotation bracket to actuator with 1/4 x 3/4 in. bolts and split lock washers. Long ear of bracket is toward hydraulic fittings of actuator. 16. Measure distance between upper and lower actuator brackets. If distance is: Less than 8-7/8 no spacer 8-7/8 9-1/8 (1) spacer Measure Bottom of Upper Bracket to the Top of Lower Bracket 9-1/8 9-3/8 (2) spacers Greater than 9-3/8 contact technical support Spacer kit must be ordered separately. 17. Position actuator between brackets. 18. Secure actuator to lower bracket with provided shoulder bolt, rubber washer and flat washer. 19. Install spacer (if applicable, explained above) between self-centering pivot base of actuator and lower bracket. Use longer shoulder bolt when spacer(s) are required. 20. Torque shoulder bolt to 25 ft-lbs. 6
21. Extend actuator up so that 9/16 in. stud is engaged in hole of upper bracket 22. Install rubber washer, steel washer, and castle nut to secure actuator into upper bracket. Castle nut is properly tightened when upper self-centering pivot base of actuator is tight against upper bracket and rubber washer is slightly compressed. 23. Install provided cotter pin to lock castle nut in position. 7