Removing and installing trim panel vw-wi://rl/a.en-gb.a03.5106.29.wi::31914802.xml?xsl=3 1. oldal, összesen: 1 oldal Removing and installing trim panel Removing Carefully prise out trim panel -1- in direction of arrow. Pull off trim panel -1- to front. Installing Install trim panel -1- in reverse order of removal.
Removing and installing door trim (front) vw-wi://rl/a.en-gb.a03.5106.29.wi::31914801.xml?xsl=3 1. oldal, összesen: 3 oldal Removing and installing door trim (front) Special tools and workshop equipment required Torque wrench -V.A.G 1410-1 - Door trim Removing Remove trim panel -3- Chapter. Unscrew bolt -2-. Close hinged pocket -5-. Unscrew bolt -4-. Starting at bottom, unfasten door trim -1- at clips -6- (8x). Disengage Bowden cable for interior door handle Fig.. Unplug connector at window regulator control unit Fig. Installing Make sure all clips -6- are in position on
Removing and installing door trim (front) vw-wi://rl/a.en-gb.a03.5106.29.wi::31914801.xml?xsl=3 2. oldal, összesen: 3 oldal back of door trim. Renew damaged clips Fig. Install door trim -1- in reverse order of removal. 2 - Bolt Tightening torque: 4 Nm 3 - Trim panel 4 - Bolt Tightening torque: 4 Nm 5 - Hinged pocket with mount 6 - Clips (8x) 7 - Door shell Disengaging Bowden cable for interior door handle Pull Bowden cable -2- out of guide -1-. Disengage hook -3-. Connector at window regulator control unit Unfasten retaining clip -2- and unplug connector -3- from control unit -1- in direction of arrow. Fastener for door trim
Removing and installing door trim (front) vw-wi://rl/a.en-gb.a03.5106.29.wi::31914801.xml?xsl=3 3. oldal, összesen: 3 oldal Press retaining tab -2- and pull out fastener -1- in direction of arrow.
Dismantling armrest vw-wi://rl/a.en-gb.a03.5106.29.wi::31914807.xml?xsl=3 1. oldal, összesen: 1 oldal Dismantling armrest Special tools and workshop equipment required Torque wrench -V.A.G 1783/- Remove door trim Chapter. Remove insulation Chapter and Chapter. Remove armrest Chapter. Remove bolts -5- (2x). Tightening torque: 2 Nm Unscrew bolt -4-. Tightening torque: 2 Nm Pull front section -3- of armrest -1- out of guide -2-. Push down cover -6- towards rear. Installing Assemble armrest in reverse order of removal.
Removing and installing mirror adjustment switch vw-wi://rl/a.en-gb.a03.5106.29.wi::31914808.xml?xsl=3 1. oldal, összesen: 1 oldal Removing and installing mirror adjustment switch Removing Remove door trim Chapter. Remove insulation Chapter and Chapter. Remove armrest Chapter. Dismantle armrest Chapter. Use screwdriver to prise out mirror adjustment switch -1-. Unplug connector -2-. Installing Install mirror adjustment switch -1- in reverse order of removal.
Removing and installing window regulator motor vw-wi://rl/a.en-gb.a02.5105.89.wi::33968806.xml?xsl=3 1. oldal, összesen: 1 oldal Removing and installing window regulator motor Removing Door trim removed Rep. Gr.70. Note Window regulator motor can be removed or installed with motor or side window in any position. Unplug connectors before removing motor. Unscrew Torx bolts -2--T30- and detach motor. Installing When installing, make sure threaded pins - arrows- are engaged in inner door panel. Fit window regulator motor -3- and secure with bolts -2-. Tightening torque: 3.5 Nm. Note After installing the electric motor and attached wiring, first turn the ignition on and then off again. Then raise door window as far as it will go and keep window regulator switch pulled for approx. 2 seconds. The window regulator is now in the basic setting and the opening/closing function is activated.
Removing and installing mounting panel vw-wi://rl/a.en-gb.a02.5105.89.wi::33968804.xml?xsl=3 1. oldal, összesen: 3 oldal Removing and installing mounting panel 1 - Mounting panel Door trim removed Rep. Gr.70 Removing: Disconnect all electrical wires to control units/loudspeakers. Unfastened or severed cable ties must be attached at same position as on removal. Remove window regulator motor Chapter. Remove plastic covers at penetrations -arrows- in mounting panel Fig. Slide door window down by approx. 10 cm until door window drivers -6- with bolts -3- can be accessed through penetrations -arrows-. 2 - Torx bolt 4.5 Nm Must be unscrewed before door window or mounting panel can be removed 3 - Window regulator Removing Chapter. 4 - Front door 5 - Mountings
Removing and installing mounting panel vw-wi://rl/a.en-gb.a02.5105.89.wi::33968804.xml?xsl=3 2. oldal, összesen: 3 oldal Must rest on window regulator drivers when fitting door window Anchor and Fig.. 6 - Torx bolts 8 Nm 7 - Connecting element Installation position Fig. 8 - Motor for power latching system Removing and installing Chapter 9 - Hexagon flange nuts 5 Nm 10 - Washer Must always be fitted. 11 - Cable Engage in motor for power latching system Fig. Cover for mounting panel Pull out cover -2- before removing mounting panel -1- or door window. Driver (front) Detach mounting -2- for door window from driver -3- when removing door window or mounting panel -1-. When installing, tighten Torx bolt -4- to 4 Nm. When installing, make sure window mounting -2- is resting on top edge of driver -3-.
Removing and installing mounting panel vw-wi://rl/a.en-gb.a02.5105.89.wi::33968804.xml?xsl=3 3. oldal, összesen: 3 oldal Driver (rear) Unscrew door window mounting -2- from driver -3- when removing door window or mounting panel -1-. When installing, tighten Torx bolt -4- to 4 Nm. When installing, make sure window mounting -2- is resting on top edge of driver -3-. Connecting element pre-assembly operations If necessary, remove adhesive aluminium strips -2- over holes at mounting panel -1- (new component only). Insert connecting elements -3- in mounting panel -1- and tighten hexagon nuts -4- to 20 Nm.
Removing and installing window frame and window regulator vw-wi://rl/a.en-gb.a02.5105.89.wi::33968802.xml?xsl=3 1. oldal, összesen: 2 oldal Removing and installing window frame and window regulator 1 - Window frame Mounting panel removed Chapter Can only be removed after detaching door window from window regulator. When installing, observe tightening sequence for bolts. When installing, start by screwing in all bolts loosely. Height of window frame is already set by fitted flange bolts - 4- and -5-. After setting angle, tighten bolts to 32 Nm in following sequence: - 4-, -5-, -6-, - 7-, -8-, -9- and -10-. 2 - Door window Fitted during assembly of window frame Can be renewed with mounting panel and window frame fitted. 3 - Exterior mirror Removing Chapter. 4 - Fitted flange bolt Multi-point socket head 32 Nm 5 - Fitted flange bolt Multi-point socket head 32 Nm 6 - Torx bolt
Removing and installing window frame and window regulator vw-wi://rl/a.en-gb.a02.5105.89.wi::33968802.xml?xsl=3 2. oldal, összesen: 2 oldal 32 Nm 7 - Torx bolt 32 Nm 8 - Pan-head bolt 10 Nm 9 - Pan-head bolt 10 Nm 10 - Pan-head bolt 10 Nm 11 - Front door 12 - Door seal (outer) Removing and installing Fig. Fitting outer door seal Removal involves unscrewing bolt -3- at bottom. Unclip seal at top from door and detach seal. Bonding surface must be free of dust and grease. Before fitting, clean bonding surface at door -1- with D 009 401 04. When installing, start by clipping seal -2- into door (top). Working from bottom, detach backing as far as embossed area. Bond on seal in embossed area. Fix moulding in position at bottom and fully bond on seal in lower area. Detach rest of backing and bond on seal in upper area. Press seal firmly onto door. Screw on seal at bottom with bolt -3-.