Milking variables in relation to teats preparation and unit attachment delay in cows

Similar documents
Somatic Cell Count Benchmarks

Heritability Estimates for Conformation Traits Gladys Huapaya and Gerrit Kistemaker Canadian Dairy Network

The Brake Assist System

KERN FIELD CROPS. Kern County 1031 S. Mt. Vernon Avenue Bakersfield, CA

Forage Harvester Evaluation

Dynamic characteristics of railway concrete sleepers using impact excitation techniques and model analysis

Evaluating Losses in Electrical Equipment Focus on Transmission Utilities. CNY Engineering Expo 2016 Syracuse, New York Arthur C. Depoian P.E.

Dairy Cattle Career Development Event

First Do No Harm: Why Seatbelts are a Patient Care Issue. Noah Smith, NHTSA Office of EMS

Exercise 3. Battery Charging Fundamentals EXERCISE OBJECTIVE DISCUSSION OUTLINE DISCUSSION. Charging fundamentals

DRIVER SPEED COMPLIANCE WITHIN SCHOOL ZONES AND EFFECTS OF 40 PAINTED SPEED LIMIT ON DRIVER SPEED BEHAVIOURS Tony Radalj Main Roads Western Australia

Forage Harvester Evaluation

Effect of Sample Size and Method of Sampling Pig Weights on the Accuracy of Estimating the Mean Weight of the Population 1

A Study of Lead-Acid Battery Efficiency Near Top-of-Charge and the Impact on PV System Design

A Comparison of Fuel Usage and Harvest Capacity in Self-Propelled Forage Harvesters

The purpose of this experiment was to determine if current speed limit postings are

Charging and Discharging Method of Lead Acid Batteries Based on Internal Voltage Control

Evaluation Considerations and Geometric Nuances of Reduced Conflict U-Turn Intersections (RCUTs)

Safety Evaluation of Converting On-Street Parking from Parallel to Angle

PVP Field Calibration and Accuracy of Torque Wrenches. Proceedings of ASME PVP ASME Pressure Vessel and Piping Conference PVP2011-

PUBLICATION NEW TRENDS IN ELEVATORING SOLUTIONS FOR MEDIUM TO MEDIUM-HIGH BUILDINGS TO IMPROVE FLEXIBILITY

Final Report. LED Streetlights Market Assessment Study

The Effective IVIS Menu and Control Type of an Instrumental Gauge Cluster and Steering Wheel Remote Control with a Menu Traversal

Physiologic Comparison of Yamaha JWII Power Assisted and Traditional Manual Wheelchair Propulsion

Small vents make a big difference

Cost-Efficiency by Arash Method in DEA

RESPA -CF Vortex HyperFLOW Product Validation

I. INTRODUCTION. Sehsah, E.M. Associate Prof., Agric. Eng. Dept Fac, of Agriculture, Kafr El Sheikh Univ.33516, Egypt

It s so easy. It will save time and money. Managing your change process and maintaining your cluster will improve animal health and milk quality.

WHAT IS THE PROFIT OF DRIVING FAST? -THE COMPARISON OF THE SPEEDY DRIVING AND SAFE DRIVING IN TERMS OF TRAVELING TIME-

Use of Flow Network Modeling for the Design of an Intricate Cooling Manifold

Spot Speed Study. Engineering H191. Autumn, Hannah Zierden, Seat 20. Ryan King, Seat 29. Jae Lee, Seat 23. Alex Rector, Seat 26

THIN FILM FUSE LINK. R D Harrison*, I Harrisont, A F Howet.

DOCTORATE (Ph.D.) DISSERTATION THESES

HUMAN AND TEST BAG IMPACT LOADS ON STATIONARY SEATING Min Li. Zhihui Wu* Bob Tackett. Jilei Zhang*

Dynamic Behaviour of Asynchronous Generator In Stand-Alone Mode Under Load Perturbation Using MATLAB/SIMULINK

Why array oversizing makes financial sense

A Study on the Growth Characteristics of Different Varieties of Early Rice as the Direct-seeded Plant

Factory Data: MOSFET Controls Supercapacitor Power Dissipation

Wind-Diesel Hybrid System: Overview of the Requirements, Models and Software Tools Hussein Ibrahim, Ph.D.

Quasi-Static Finite Element Analysis (FEA) of an Automobile Seat Latch Using LS-DYNA

Pump Control Ball Valve for Energy Savings

IT'S MAGNETIC (1 Hour)

OKLAHOMA CORPORATION COMMISSION REGULATED ELECTRIC UTILITIES 2017 RELIABILITY SCORECARD

Linking the Indiana ISTEP+ Assessments to the NWEA MAP Growth Tests. February 2017 Updated November 2017

Effect of Police Control on U-turn Saturation Flow at Different Median Widths

ELECTRICAL ENGINEERING & COMPUTER SCIENCE NEWSLETTER Volume

HIGH-RELIABILITY POUCH CELL CONNECTION AND COST ASPECTS OF A ROBUST BMS SOLUTION

Reducing. with Current. arc flash note 2. points of interest. Why Use Current Limiting Fuses. By mike lang, Principal field engineer

UPGRADE OF AN INDUSTRIAL Al-BSF SOLAR CELL LINE INTO PERC USING SPATIAL ALD Al 2 O 3

Charles Sullivan, Associate Professor, Thayer School of Engineering at Dartmouth

Passive Vibration Reduction with Silicone Springs and Dynamic Absorber

LINERS AND TUBES THE RIGHT COMPONENTS FOR THE BEST RESULT

3.2. Current Limiting Fuses. Contents

Using Reduced Tire Pressure for Improved Gradeability A Proof of Concept Trial

ACCIDENT MODIFICATION FACTORS FOR MEDIAN WIDTH

Flanging and Hemming of Auto Body Panels using the Electro Magnetic Forming technology

There are two leading power conversion technologies used in formation charging rectifiers

Public Transportation Problems and Solutions in the Historical Center of Quito

Equipment Strategy for Stand By Diesel Generators Strategy

Relationship between steering torque and ease of driving with bar type steering in high speed range

Longevity of turf response to urea, coated urea, and blends

Data envelopment analysis with missing values: an approach using neural network

FAULT ANALYSIS OF AN ISLANDED MICRO-GRID WITH DOUBLY FED INDUCTION GENERATOR BASED WIND TURBINE

BEDDING MANAGEMENT TOOLS

THE EFFECT OF GESTATION ON MILK AND BUTTEKFAT PRODUCTION IN DAIRY CATTLE DISSERTATION

Impurity Testing of Fixed-Dose Combination Drugs Using the Agilent 1290 Infinity II HDR-DAD Impurity Analyzer Solution

OKLAHOMA CORPORATION COMMISSION REGULATED ELECTRIC UTILITIES 2018 RELIABILITY SCORECARD

Testing of gel-electrolyte batteries for wheelchairs

Effect of cavitation in cylindrical and twodimensional nozzles on liquid jet formation

DESIGN OF HIGH ENERGY LITHIUM-ION BATTERY CHARGER

Evaluation of reed canary grass shredding and compacting properties

Watermelon Research Report 2011 On-Farm Watermelon Survey

FUEL PROVISIONS FOR DREDGING PROJECTS

3 consecutive 2-month summer campaigns

Diesel-Driven Compressor Torque Pulse Measurement in a Transport Refrigeration Unit

A TechForAg 'Ready-To-Milk' Modular Parlor Model: Dbl. 12 Thorp/Germania ParaBone Key Features:

Multi Body Dynamic Analysis of Slider Crank Mechanism to Study the effect of Cylinder Offset

Association between M-class solar flares and Coronal Mass Ejections during the solar cycle 23 rd

Low Sulphur Fuel Oils Preliminary Estimated Costs to Canadian Industry based on European Data

LES of wind turbine wakes

Investigating the Concordance Relationship Between the HSA Cut Scores and the PARCC Cut Scores Using the 2016 PARCC Test Data

MRY DECEMBER 2017 ALL SALES INQUIRIES: FREEPHONE BETTER COWS BETTER LIFE CRVAVONCROFT.COM

M216 HI-SPEED DIGITAL THERMOMETER INSTRUCTION MANUAL

Tablet PC Project Workshop

Train Group Control for Energy-Saving DC-Electric Railway Operation

(Picture of Parlor Stalls not available at this time) This parlor should milk from 160 cows to 220 cows per hour with two milkers

Utilization of Electric Power Laboratory 3 rd Year G2: Testing & Characteristic of MCCB Used in Commercial and Industrial Applications

Expected Energy Not Served (EENS) Study for Vancouver Island Transmission Reinforcement Project (Part I: Reliability Improvements due to VITR)

HOW MUCH DRIVING DATA DO WE NEED TO ASSESS DRIVER BEHAVIOR?

HHS:PHS:FDA:CFSAN:OFS:DPDFS:DEB:MST Paint Branch Parkway College Park, MD M-I February 7, 2012

Simple, Fast High Reliability Rework of Leadless Devices Bob Wettermann

NAME Bull number (ID) Born:

Research on Skid Control of Small Electric Vehicle (Effect of Velocity Prediction by Observer System)

Analysis and calculation model of energy consumption and product yields of delayed coking units

Parking Studies. Lecture Notes in Transportation Systems Engineering. Prof. Tom V. Mathew. 1 Overview 1

STUDIES ON THE EFFECTIVENESS OF IGNITION INTERLOCKS

Impact of Plug-in Electric Vehicles on the Supply Grid

Department of Civil Engineering (Transportation Engineering), Birla Vishvakarma Mahavidyalay Engineering College, Vallabh Vidyanagar, Gujarat, India

Turbo boost. ACTUS is ABB s new simulation software for large turbocharged combustion engines

Transcription:

preparation and unit attachment delay in cows H. Turki & S. Winnicki Veterinarian Department Agricultural University of Poznan, 60-625 Poznan, 52 Wojska Polskiego street E-mail: h_turki@hotmail.com Milking routines observations were carried out on 84 black and white dairy cows randomly chosen. The effect of the time taken to manually stimulate the teats (cleaning and drying) before the unit is attached prep-time divided into two classes (to 30 and >30 seconds) and the time delay from the beginning of the cow preparation process until unit attachment prep-lag time also divided into two classes (to 60 and >60 seconds) on milk flow time, total milking time, first minute milk flow rate, average milk flow rate, milk yield and somatic cell counts in milk was investigated. The longest milk flow time was observed in rear teats, for all classes of prep-time and prep-lag time. The greatest difference (P 0.05) between front and rear teats was observed for a prep-time and a prep-lag time respectively of 30 and 60 sec. Summary Prep-time had a significant effect on milk flow time (P 0.01), total milking time (P 0.01) and first minute milk flow rate (P 0.01), this effect was also observed on average milk flow rate (P 0.05). However no significant effects were observed on milk yield and somatic cell counts. Total milking time, first minute milk flow rate, average milk flow rate and milk yield decreased as prep-lag time increased. Milk yield was influenced by prep-lag time (P 0.05). No significant effects of neither prep-time nor prep-lag time was observed on somatic cell count in milk. Key words: Prep-time, prep-lag time, dairy cow, milk flow rate, milking time. To withdraw milk efficiently from the bovine mammary gland, the cow must be included as an active partner in the milking process by evoking the milk ejection reflex (Hamann, 1991). Studies have shown that milk ejection is not entirely dependant on the action of oxytocin and that there are also many other factors that control the effectiveness of oxytocin Introduction 89

response (Mayer et al., 1984; Svennersten and Claesson, 1990). According to Lefcourt (1982), the effect of teat stimulation on sympathetic tone in the mammary gland is a second milk letdown mechanism. In addition to oxytocin causing milk letdown, the nervous system also plays a role in rate of milk flow through the teat canal (Bruckmaier and Blum, 1998). A minimum of 12-15 seconds of teat contact time is required for sufficient nerve stimulation to ensure adequate oxytocin release and a good milk ejection response (Mein and Reid, 1996). Premilking cow preparation is proven to be an important step in achieving maximum milk yield, quality and udder health. Units should be attached within a window of 60 to 90 seconds from beginning of udder preparation process to take advantage of oxytocin stimulated by good teat manipulation (Rasmussen et al., 1992). The purpose of this experiment was to investigate the effect of the time taken to manually clean and dry the teats before the unit is attached and the time from the beginning of the cow preparation process until unit attachment on milk flow time, first minute milk flow rate, average milk flow rate, milk yield and somatic cell count in milk. Material and methods A field study was carried out on 84 black and white dairy cows randomly chosen. Cows were held in a two tie-stall barn and milked to a pipeline by a set of four milking units MilkMaster with automatic teatcups detachers. All cows were milked using the same milking routine consisting of fore stripping of three to five squirts from each teat followed by teat cleaning with a different total duration. The machine was attached in a different time for each cow after preparation. The time taken to manually clean and dry the teats before the unit is attached is referred to as Prep time and the time from the beginning of the cow preparation process until unit attachment is referred to as Prep lag time (Reneau and Chastain, 1995). Time studies were conducted for three consecutive days at evening milking. Prep time, Prep lag time, milk flow time from individual quarters, first minute milk flow rate, average milk flow rate, total milking time and milk yield were recorded. On the fourth day milk samples were taken during evening milking in order to determinate somatic cell counts using Fossomatic 4000. The effect of prep time divided into two classes (to 30 sec., >30 sec.) and prep lag time into two classes (to 60 sec., > 60 sec.) on first minute milk flow rate, average milk flow rate, total milk yield and total milking time was investigated. Results are presented tables as means ± SD. For statistical evaluations STATISTICA 97 software was used. Mean differences of different classes were tested for significant differences using the Duncan s Test. 90 Conference on "Physiological and technical aspects of machine milking"

Table1. Milk flow time from in individual quarters in relation to prep-time and prep-lag time. Seconds Front teats Rear teats Prep-time Prep-lag time Number of cows Left Right Left Right Quarter effect 0-60 31 230±34 AB 249±48 AB 290±74 Aa 303±78 A X 0-30 > 60 29 244±44 CD 234±52 CD 269±77 BC 272±92 Ba X 0-60 11 307±72 AC 310±56 AC 362±76 AB 389±123 AB X > 30 > 60 13 284±40 BD 308±82 BD 343±62 Ca 350±76 a X Prep-time effect XX XX XX XX - Prep-lag time effect NS NS NS NS - Lactation effect XX XX XX XX - Means in columns designated by the same capital letter are significantly different at P 0,01. Means in columns designated by the same small letter are significantly different at P 0,05. NS- means not significant. 91

Results and discussion Average milk flow time (MFT) increased significantly in all quarters (P 0.01) as prep time increased (Table 1), however no significant effect of prep-lag time was observed even though as cow prep lag time increased, (MFT) decreased. According to Eicker et al., (2000), a well-prepped cow will letdown her milk rapidly and completely and her average flow rate will be higher. The longest (MFT) was observed in rear teats, for all classes of prep-time and prep-lag time. The greatest difference (P 0.05) in (MFT) between front and rear teats was observed for a prep-time and a prep-lag time ranging respectively from 0 to 30 and from 0 to 60 sec. The quarter effect was significant (P 0.05). Rear teats normally have higher milk yield and take longer to milk than the front ones (Rassmusen, 1993). First minute milk flow rate (FMMFR) (P 0.01) and average milk flow rate (AMFR) (P 0.05) were influenced by prep-time and prep-lag time (Table 2). (FMMFR) and (AMFR) were the highest for a prep-time from 0 to 30 sec. and a prep-lag time from 0-60 sec. As prep-time and prep-lag time increased, (FMMFR) and (AMFR) decreased. According to Gorewit and Gassman (1985) a stimulation for 60 or 120 sec. did not achieve higher peak milk flow rates than 15 or 30 sec., and the average milk flow rate increased and machine-on time decreased with duration of stimulation. Milk yield was not affected by prep-time, however it was influenced significantly (P 0.05) by prep-lag time. According to Bruckmaeir and Blum, (1996) milk yield was not significantly lower in milking without than with stimulation, whereas machine-on time was prolonged and peak milk flow rate was reduced during milking without stimulation. Total milking time (TMT) increased (P 0.01) as prep-time increased and decreased as prep-lag time increased. The longest (TMT) was observed for a prep-time and a prep lag-time respectively over 30 sec. and ranging from 0 to 60 sec. This is probably due to an inadequate stimulus of the udder. According to Rasmussen et al., (1992) the ideal prep-lag times are 1.3 minutes, or 1.18 minutes. They found that a range of 1 to 1.5 minutes is accepted as the optimal prep-lag time for all stages of lactation. Gorewit and Gassman (1985) concluded that it takes longer to milk out the last kg of milk if premilking teat preparation is conducted inefficiently or even omitted. On the other hand the shortest (TMT) was observed when prep-time ranged from 0 to 30 sec. and prep-lag time was over 60 sec. Better milking preparation causes faster let-down and better milk-out and allows shorter unit-on times (Stewart, 1993). Merill et al., (1987) tested the effects of premilking preparation (full stimulation and minimum stimulation) on milk flow rates and machine-on time. They found that cows receiving full stimulation had significantly higher average milk flow rates and shorter machine on-times starting at week 32. Milk flow rate and yield determine the unit-on time and can have a significant effect on throughput (Reneau and Chastain, 1995). According to Pfeilsticker et al. (1995), the time from the start of teat stimulation until maximal pressure (ejection pressure) is 115 seconds. However, milkers, compelled by the speed of premilking cow prep rather than thoroughness, often fail to 92 Conference on "Physiological and technical aspects of machine milking"

Table 2. First minute milk flow, average milk flow, milk yield and total milking time in relation to Prep-time and prep-lag time. Seconds (kg/min) Prep-time Prep-lag time Number of cows First minute milk flow Average milk flow Milk yield (kg) Total milking time (sec.) Ln SCC 0-30 0-60 31 2.905±0.800 AB 2.476±0.823 a 8.263±2.182 313±78 A 10.504±1.256 > 60 29 2.429±0.735 CD 2.122±0.514 7.240±2.290 282±92 BC 10.655±1.207 > 30 0-60 11 1.903±0.967 AC 2.024±0.685 8.042±2.314 399±73 AB 11.654±0.752 > 60 13 1.507±0.384 BD 1.789±0.691 a 6.641±1.926 360±80 C 10.772±1.248 Prep-time effect XX X NS XX NS Prep-lag time effect XX X X NS NS Lactation effect X NS XX XX NS Marks as in table 1. 93

achieve either adequate teat sanitation or consistent milk letdown stimulus. No significant effects of neither prep-time nor prep-lag time was observed on somatic cell count in milk. Conclusion Average milk flow time increased significantly in all quarters (P 0.01) as prep time increased, on the other hand no significant effect of prep-lag time was observed on milk flow time. The longest milk flow time was observed in rear teats, for all classes of prep-time and prep-lag time. First minute milk flow rate and average milk flow rate were influenced by prep-time and prep-lag time. As prep-time and prep-lag time increased, first minute milk flow rate and average milk flow rate decreased. Milk yield was not affected by prep-time, however it was influenced significantly by prep-lag time. Total milking time increased as prep-time increased and decreased as prep-lag time increased. The longest total milking time was observed for a prep-time and a prep lag-time respectively over 30 sec. and ranging from 0 to 60 sec. No significant effects of neither prep-time nor prep-lag time was observed on somatic cell count in milk. References Bruckmaier RM, Blum JW. 1996. Simultaneous recording of oxytocin release, milk ejection and milk flow during milking of dairy cows with and without prestimulation. J Dairy Res. May; 63(2): 201-8. Bruckmaier, R.M. and Blum, J.W. 1998. Oxytocin release and milk removal in ruminants. J. Dairy Sci. 81, 939. Eicker S., Stewart S., Reid D., Rapnicki P. and Ferry K. 2000. New Tools for measuring the effect of stimulation and take-off on milk flows. In Proceedings Annual Meeting, National Mastitis Council Proceedings. USA. Gorewit, R.C., and K.B.Gassman. 1985. Effect of duration of udder stimulation on milking dynamics and oxytocin release. J. Dairy Sci. 68: 1813. Hamann J. 1991. Milking related teat tissue changes as a predisposing factor for mastitis. Flem.Vet. J. 62, suppl. 1, 57-68. Lefcourt, A.1982. Effect of teat stimulation on sympathetic tone in bovine mammary gland. J. Dairy Sci. 65: 2317. 94 Conference on "Physiological and technical aspects of machine milking"

Mayer H., Schams D., Worstorff H. and Prokopp A.1984. Secretion of oxytocin and milk removal as affected by milking cows with and without manual stimulation. J. of Endocrinology 103: 355-361. Mein D., Reid D.A.1996. Milking time tests and guidelines for milking units. In Proceedings 35 th Annual Meeting, National Mastitis Council, Madison, WI, USA, 235-244. Merrill WG, Sagi R, Petersson LG, Bui TV, Erb HN, Galton DM, Gates R.1987. Effects of premilking stimulation on complete lactation milk yield and milking performance. J Dairy Sci. 70(8): 1676-84. Pfeilsticker H.U., Bruckmaier R.M., Blum J.W. 1995. Interruption of machine milking in dairy cows: effect on intrammamry pressure and milking characteristics. J. Dairy Res. 62: 359-366. Rasmussen, M.D., E.S. Frimer, D.M. Galton and L.G. Peterson. 1992. The influence of premilking teat preparation and attachment delay on milk yield and milking performance. J. Dairy Sci.75: 21-31. Rasmussen M.D.1993.Influence of switch level of automatic cluster removers on milking performance and udder health. J. Dairy Res. 60: 287-297. Reneau J.K. and Chastain J.P. 1995. Effect of cow prep on milk flow, quality and parlor throughput. In Dairy update issue 119, University of Minnesota, St. Paul, USA. Stewart S., P. Billon, G.. Mein 1993.Predicted maximum milk flow rates in milking systems. In National Mastitis Council, Annual Meetings Proceedings, pp. 125-132. Svennersten, K. and C.O. Claesson. 1990.Effect of local stimulation of one quarter on milk production and milk components. J. Dairy Sci. 73: 970-974. 95