Assembly Manual FELIX One

Assembly Manual FELIX One Version 1.0 2018 www.felixprinters.com support@felixprinters.com Zeemanlaan 15 3401 MV IJsselstein The Netherlands

Introduction Table of Content Dear Customer, Thank you for choosing FELIXprinters! To get your Felix printer up and running as fast and painlessly as possible please follow this manual carefully. Please don t take any shortcuts. It s better to spend a few minutes extra on reading, than to wait a week for new parts. When things are unclear or if you have any remarks or tips, please contact us at support@felixprinters.com. We also recommend looking on our forum and getting yourself a forum account. You will benefit from the ability to get downloadable and printable upgrades for your printer. Also it is a great source to obtain and share knowledge about your 3D printer and 3D printing in general. Have fun building! Kind regards, FELIXprinters. Required tools 5 Chapter 1: Frame 6 Chapter 2: Z-axis 8 Chapter 3: X-axis 11 Chapter 4: Y-axis 15 Chapter 5: Print Head 19 Chapter 6: Wiring 27 Chapter 7: Upload Firmware 31 Chapter 8: Installing LCD 32 Chapter 9: Functional test 33 Chapter 10: Finishing Touch 35 Chapter 11: Checklist 36 Bill of Material 38 FELIXprinters Assembly Manual for the FELIX One Page 3

Notice Before starting the assembling: Check the content of the kit if it is complete according to the bill of material in the appendix of this document. FELIXprinters Assembly Manual for the FELIX One Page 4

Required 1,5 2 2,5 3 4 5 5,5 7,0 12 Hexagon Key 1,5mm Hexagon Key 2mm Hexagon Key 2,5mm Hexagon Key 3mm Hexagon Key 4mm Hexagon Key 5mm Tweezer Wrench 5,5 mm 7,0 mm and 12 mm + - Grease Lubricant Phillips Head Screwdriver Slotted Head Screwdriver Small Pliers Knife / Box Cutter Rubber Hammer* Tape Measure Alcohol *Or use a steel hammer with a soft piece of rubber or plastic to absord the impact. FELIXprinters Assembly Manual for the FELIX One Page 5

Chapter 1: Frame 30 Minutes 1!! Hole!! 2!! Hole!!!! Hole!! 5 (1x) Profile 4 (2x) Bolt M8 x 20 (2x) Frame Connector 5 (1x) Profile 1 3 4 5!! Hole!!!! Hole!!!! Hole!! 160mm!! Hole!! 160mm!! Hole!! 5 (1x) Profile 2 (1x) Bolt M8 x 20 (1x) Frame Connector 5 5 FELIXprinters Assembly Manual for the FELIX One Page 6

6 7 8!! Hole!! (1x) Profile 2 (1x) Bolt M8 x 20 (1x) Frame Connector 5 5 (1x) Profile 3 (2x) Bolt M8 x 20 (2x) Frame Connector 5 9 10 11 5 Make sure the profiles are properly aligned. If not untighten the screws and readjust the profiles. (4x) End Cap Square (1x) End Cap Rectangle FELIXprinters Assembly Manual for the FELIX One Page 7

Chapter 2: Z-Axis 45 Minutes i 1 2 3 1,5 2 3 4 Example - Insert T-Nut: Insert the nut into the slot 2 Example - Insert T-Nut: Insert the key into the threaded hole and rotate the nut into position. 2 12 13 14 (4x) CSK Bolt M3 x 8 (1x) Motor (1x) Z-Axis Motor Bracket 2 (1x) Cable Stepper Z (1x) Motor Assembly (2x) T-Nut M4 (2x) Bolt M4 x 20 (2x) Small Washer M4 3 FELIXprinters Assembly Manual for the FELIX One Page 8

15 16 17 4cm 16cm 28cm!! Don t let the Carriage run of the Rail!! (3x) T-Nut M4 (3x) Bolt M4 x 20 (1x) Linear Guide HGW15 (1x) Z-Axis Lift (1x) Hexagon Nut 2 Use tape measure to allign. 3 18!! Remove Bolts after pulling Locknuts into Z-Axis Lift!! 19 20!! Washer!!!! Washer!! (2x) Bolt M4 x 40 (2x) Locknut M4 3 (4x) Bearing (2x) Bolt M4 x 25 (2x) Small Washer M4 3 FELIXprinters Assembly Manual for the FELIX One Page 9

21!! Tighten in a Crosswise Pattern!! 22 23!! Make sure the flat side of the Motor Axle is Perpendicular to the Set Screw!! 1 4 3 2 (1x) Z-Axis Lift Assembly (4x) Bolt M5 x 16 (4x) Small Washer M5 4 (1x) Motor (1x) Pulley (1x) Set Screw M3 x 6 (1x) Cable Stepper Y 1,5 (1x) Cable Stepper Y 24 25 26!! Make sure the Hexagon Nut stays in its Socket!!!! Apply Grease to the Spindle. Do NOT use Oil as Lubricant!!!! Make sure the flat side of the Motor Axle is Perpendicular to the Set Screw!! (1x) Motor Assembly (4x) CSK Bolt M3 x 8 2 (1x) Spindle (1x) Set Screw M3 x 6 Note: use a high quality and sharp 1.5 mm allen key to properly fix the spindle on the motor. 1,5 FELIXprinters Assembly Manual for the FELIX One Page 10

Chapter 3: X-Axis 60 Minutes 27 28!! Washer!! 1,5 2 2,5 3 - + 1,5 14 (1x) T-Nut M4 2 (2x) Bearing (1x) Small Washer M4 (1x) X-Axis Belt Mount (1x) Bolt M4 x 40 3 29 2 30 31!! Make sure the short side of the T-nut is facing the corner of the frame!! 1 3 2 1 (1x) Belt (1x) X-Axis Belt Mount Assembly (1x) T-Nut M4 3 2 FELIXprinters Assembly Manual for the FELIX One Page 11

32 33 34 (1x) Bolt M4 x 16 (1x) Small Washer M4 3 (1x) T-Nut M4 (1x) Bolt M4 x 16 (1x) Small Washer M4 (1x) X-Axis Motor Bracket 2 35 36 37 14mm from the side of the rail to side of the frame!! 14 mm!! Reposition the Safety Plugs as shown!! (2x) T-Nut M3 (black) (1x) Linear Guide MGN12 (2x) Bolt M3 x 12 (1x) Linear Guide MGN12 2 2,5 FELIXprinters Assembly Manual for the FELIX One Page 12

38!! Make sure to Position the Rail against X-Axis Belt Mount!! 39 40!! Make sure the flat side of the Motor Axle is Perpendicular to the Set Screw!! 2,5 (1x) Motor (1x) Pulley (1x) Set Screw M3 x 6 1,5 (1x) Cable Stepper X 41 42 43!! Tighten in a Crosswise Pattern!! 1 4 3 2!! Use Tweezer to Position the Bolts!! (1x) Motor Assembly (4x) CSK Bolt M3 x 8 (2x) Small Screw 2,2 x 8 (1x) Opto Sensor X (4x) CSK M3 x 6 (1x) Extru Base 2 + 2 FELIXprinters Assembly Manual for the FELIX One Page 13

44 45!! Use a screwdriver to Push the Belt completely into the Socket!! 46 3 1 2 47!! Insert the Square Nut into the Tension Bracket!! 48 49 -!! Use the Screwdriver to Push the Belt completely into the Socket!!!! Move the carriage to the center of the rail. Tighten the belt using the size 3 hexagon key until the belts can barely touch eachother when pressing them together!! 2 cm (1x) Tension Bracket (1x) Square Nut M4 (1x) Tension Bracket Assembly (1x) Bolt M4 x 25 3 FELIXprinters Assembly Manual for the FELIX One Page 14

Chapter 4: Y-Axis 30 Minutes 50 51!! Don t let the Carriage run of the Rail!!!! (1x) Thin Nut M4!!!! Endswitch Vane!! + - 2,5 3 5,5!! (1x) Thin Nut M4!! 52 (2x) Small Screw 2,2 x 8 (2x) Thin Nut M4 (1x) Opto sensor Y 53 54 + (4x) Bolt M3 x 16 (4x) Locknut M3 (4x) Small Washer M3 (1x) Y-Stage Bracket Pt.1 (1x) Y-Stage Bracket Pt.2 (1x) Hiwin Linear Guide MGN12 2,5 5,5!! Tighten in a Crosswise Pattern!! 1 1 3 4 2 2 (2x) Bolt M3 x 12 (1x) Y-Stage Bracket 2,5 (1x) Tension Bracket (1x) Bolt M4 x 25 (1x) Square Nut M4 3 (4x) Bolt M3 x 16 (4x) Small Washer M3 (1x) Y-Stage Assembly 2,5 FELIXprinters Assembly Manual for the FELIX One Page 15

55!! Use the Screwdriver to Push the Belt completely into the Socket!! 56 57!! Use the Screwdriver to Push the Belt completely into the Socket!! M3 x 25 4 2 cm 2 3 1 Tensioning the Belt: Move the Y-Axis completely to one end. Tighten the belt using the size 3 hexagon key until the belt can barely touch the rail of the Y-Axis (1x) Belt - - 3 58 59 60 (1x) Build Platform (1x) Short Wire Sleeve FELIXprinters Assembly Manual for the FELIX One Page 16

61 62 63!! Repeat for Front and Rear Thumbscrew!!!! Give the Cable enough Slack and tighten the Cable Ties!! (2x) Thumb screw (2x) Spring (1x) Build Platform Assembly (2x) Cable Tie 64!! Tighten the Bolt against the end of the Thread!! 65 66!! Give the Cable enough Slack and tighten the Cable Tie!! End to End 25cm (1x) Bolt M4 x 16 (1x) Spring (1x) Cable ties for mounting cables on z bracket (1x) Cable ties for mounting cables on z bracket 3 FELIXprinters Assembly Manual for the FELIX One Page 17

Chapter 5: Print Head 90 Minutes 69 70!! For Dual Head: Repeat this Step!!!! For Dual Head: Repeat this Step!! 1,5 1,5 2,5 3 (2x) Large Washer M4 (1x) Bolt M4 x 12 (1x) Thin Nut M4 (1x) Spring 3 (1x) Extru Arm Pt. 1 (1x) Bearing 71!! For Dual Head: Repeat this Step!! 72 73!! For Dual Head: Repeat this Step!!!! Repeat this Step!!!! Make sure the flat side of the Motor Axle is Perpendicular to the Set Screw!! (1x) Extru Arm Pt. 2 (1x) Motor (1x) Extruder drive wheel (1x) Set Screw M3 x 6 1,5 (1x) L-Bracket (1x) Square Nut M4 FELIXprinters Assembly Manual for the FELIX One Page 18

74!! Repeat this Step!! 75 76 Motor E1 Motor E1 (1x) Bolt M4 x 40 Bolt is used to keep square nut in place during assembly. 3 (3x) Bolt M3 x 16 (1x) L-Bracket Assembly (1x) Motor 2,5 (1x) Square Nut M4 (1x) Extruder Arm Assembly (1x) Spring Assembly 77 Motor E1 (1x) L-Bracket FELIXprinters Assembly Manual for the FELIX One Page 19

95 96 97! Make sure the sticker from the fan is at the back. The fan blows on the side of the sticker Align the print head on the carrier 98 Label end of the hot-endcable: 0 Mount the bolt loosely. Label end of the wire: 2 99 2,5 100! Tighten the bolt (2x M4) Place nuts for ease of assembly. 2,5 FELIXprinters Assembly Manual for the FELIX One Page 20

95 96 97 (2x) Bolt M4 x 40 (used in step 74) Connect sensor assembly and the fan + LED onto the main assembly. 2,5 98 99 100 (2x M4) Place nuts for ease of assembly. 2,5 FELIXprinters Assembly Manual for the FELIX One Page 21

101 102 103 1 x 2 x Guide fan wires to front of bracket. (3x) small cable tie bundle cables, but do not tighten too much. (2x) print head assembly Bend wires a little bit so they come to the front, while heads are still parallel to each other. 104 105 106 1. Remove nuts (placed in step 98) 2. (1x) small cable tie Mount front assembly. Bundle print head wires, motor wire and sensor wire. Place cable tie loosely. (2x) normal cable tie (1x) Long cable sleeve Mount left motor wire and print head wires together with cable bundle from right side. (2x) M4 x 12 Connect extruder assembly by placing two bolts. 2,5 2,5 FELIXprinters Assembly Manual for the FELIX One Page 22

107 1. Place flexplate on top of buildplate. 2. Move z-sensor above leveler wheel. 3. Move platform up, until left or right hot-end touches build plate. 4. Adjust height of z-sensor, until the distance between sensor and leveler wheel is the thickness of the calibration card. (Detailed Z-height calibration process is explained in the Quick Start Guide) FELIXprinters Assembly Manual for the FELIX One Page 23

Chapter 6: Wiring 108 109 60 Minutes 24cm End to End 38cm + 3 (2x) Single Cable Clip (1x) Angled Cable Clip 110 111 112 (1x) Single Cable Clip (2x) Single Cable Clip (2x) Dual Cable Clip FELIXprinters Assembly Manual for the FELIX One Page 24

113 114 115 1x Y-stage bracket pt1 1x Y-stage bracket pt2 4x Bolt M3x16 4x Smal washer M3 4x Self locking nut M3 116 117 118 1x Bolt M3x8 1x Small t-slot M3 1x Y stage tensioning bracket 1x Thin nut M4 1x Bolt M4x25 (1x) Electronic Enclosure Assembly 3 FELIXprinters Assembly Manual for the FELIX One Page 25

113 114 115! ATTENTION: Bottom of set-screw should NOT touch plate internally. Keep distance of approx. 0.5mm 3x Set screw M4x30 3x Thin nut M4 116 117 118 Large washer! Tighten the nuts a couple of turns, make sure that the springs are still able to compress for further fine-adjustment later. 3x spring 2x Small washer 1x Large washer 3x Thin nut M4 2x tie-wrap FELIXprinters Assembly Manual for the FELIX One Page 26

113 114 115 1x 25 cm Cable spiral 116 117 118 +/- 1cm Belt! Mount the belt, according to the arrows. FELIXprinters Assembly Manual for the FELIX One Page 27

113 114 115! Ends of the plastic strip must be cut at an angle! 1x 25 cm Cable spiral 1x Clamp + Cable tie 1x 13 cm Plastic U-profile 116 The y-axis and the print bed are finished. FELIXprinters Assembly Manual for the FELIX One Page 28

113 114 115 End to End 25 cm (2x) Power Supply Screw (1x) Power Supply (1x) Electronic Enclosure Pt. 2 + (2x) Power Supply Screw (1x) Electronic Enclosure Pt. 1 + 116!! Position the narrow edge upwards!! 117!! Make sure to position the left T-Nut against the profile!! 118 1 2 23cm!! First slide the Enclosure against the left T-Nut, next slide the right T-Nut with Bolt into the Slot. Finally tighten the Two Bolts!! (1x) Electronic Enclosure Cover Plate (2x) T-Nut M4 (2x) Bolt M4 x 12 (1x) Electronic Enclosure Assembly 3 3 FELIXprinters Assembly Manual for the FELIX One Page 29

Overview: Control Board Note: E0 = E1 on control board Important: 119 1. Set the Blue Potentiometers to the correct value as shown in the overview. 120 2. Tighten the screw terminals with force to ensure a good connection. 121 3. Make sure the Control board is positioned correctly, so that the underside doesn t touch the power supply. Main board side Red Blue Green Black Black Red Green Blue Motor side FELIXprinters Assembly Manual for the FELIX One Page 30

122 123 124!! Plug the connector into the matching socket description!! (4x) Square Nut M4 (1x) Control Board end X = Endswitch X (Opto sensor) end Y = Endswitch Y (Opto sensor) Z sensor cable has no label. 125 (1x) Display Assembly FELIXprinters Assembly Manual for the FELIX One Page 31

Chapter 7: Upload Firmware 15 Minutes Download the Firmware: Download the latest FELIX One Firmware version from: http://www.felixprinters.com/downloads_felixprinters Upload the Firmware to the Control Board: 1. Unzip the downloaded file to a convenient location. (Note: if you click on the zip file from within the Windows explorer, it will NOT be unzipped. You just view the content of the zip. You need to select the files and drag them to the desired location.) 2. Connect your printer to your computer and turn it on. Do not make a connection at this time with the printer with programs like Repetier-Host or Simplify3D. 3. Start the batch file upload_automatic.bat. A script will start in a command window. 4. The script will try to detect what COM port your printer is using. Check if this is correct, and then proceed by entering Y in the command window. 5. The firmware is uploaded when Programming finished! is displayed, this may take a few minutes. 6. Press any key to continue. The FELIX One firmware is now successfully uploaded. Note for Experienced Users: Due to compatibility issues with linux based systems, the baudrate for the FELIX Tec 4 is lowered to 115200. Make sure to adjust the settings in the used software accordingly. FELIXprinters Assembly Manual for the FELIX One Page 32

122 123 124 2x Small screw 2,2 x 8 10 125 126 (1x) Display Interface PCB (1x) Display Assembly 1x Plastic Display-cover FELIXprinters Assembly Manual for the FELIX One Page 33

127 128 128! Connecting the display cables 130 130 (2x)!! Clean the surface of the frame first before applying the damping feet!! Align the square nuts from step 88 properly before mounting the cover with the m4x12 bolts. (2x) (2x) (6x) Damping Feet FELIXprinters Assembly Manual for the FELIX One Page 34

Chapter 9: Functional Test 10 Minutes In order to make sure all motors, sensors and LCD panel are connected properly, the following tests need to be performed Main board Tec 4 Check heaters: Check Sensor Connections: Z-sensor The z-sensor can be tested by holding a metal object underneath the sensor. Check if the z-sensor LED turns off. When the z-sensor indication LED on the main board switches off, the sensor is activated. Y-sensor Manually move the bed to its end position to activate the y-sensor. Check if the y-sensor LED turns off. When the y-sensor indication LED on the main board switches off, the sensor is activated. X-sensor Manually move the extruder to its end position to activate the x-sensor. Check if the x-sensor LED turns off. When the x-sensor indication LED on the main board switches off, the sensor is activated. IMPORTANT: Keep hand near ON/OFF switch of printer, in case things go wrong. Warm up left extruder (E1). Note: The hot-ends might smell a bit the first time heating. This is because of a small amount of oil within certain parts. Click rotary button to enter the main menu --> Control --> scroll down to heater --> Click on E1 and rotate until setpoint temperature increases to about 100 degc. Then check if temperature for that heater goes up. Repeat these steps for the right extruder (E2) and for the Bed (55degC). FELIXprinters Assembly Manual for the FELIX One Page 35

Check Motor Cable Connections: IMPORTANT: Keep hand near ON/OFF switch of printer, in case things go wrong. X-axis motor To make sure the wires are connected as required it is important to test all connections. To do so for the x-axis: enter menu by pushing the rottary button --> Control --> Move --> Home X Y-axis motor To test the y-axis: enter menu by pushing the rottary button --> Control --> Move --> Home Y Z-axis motor NOTE: When doing home z, extruders heatup to 120 DegC to prevent possible filament blobs from scratching the kapton surface layer. Important: ensure flexplate is placed on the print bed. To test the z-axis: enter menu by pushing the rottary button --> Control --> Move --> Home Z FELIXprinters Assembly Manual for the FELIX One Page 36

Chapter 10: Finishing Touch 15 Minutes 131!! Peel off the protective sheet at the corner and stick the exposed adhesive to the BuildPlate at one corner!! 1 + 3 Preheat your buildplate to 60 C degrees to make sure the Kapton Foil will have good adhesion to the flexible plate. 2!! Continue peeling off the protective sheet and at the same time stick the foil to the BuildPlate using a soft object in a zigzag motion to avoid air bubbles!! (1x) Kapton Foil 132 133 134!! Use the Screwdriver to center the Square Nut before inserting the Bolts!! (4x) M4 x 12 (1x) Electronic Enclosure Cover + 3 (1x) Main Fan Cover Connect the fan cover onto the extruder unit. FELIXprinters Assembly Manual for the FELIX One Page 37

Chapter 11: Checklist Frame: 1. Frame bolts (6x) are properly fixed. 2. Frame profiles are perpendicular and propely aligned. 3. Damping feet are placed underneath the printer. X-axis: 1. X-axis rail is properly aligned. 2. Bolts (2x) X-axis rail are properly fixed. 3. X-axis belt pushed fully into bracket and tensioner. 4. Belt remains at same height during moving the X-axis. 5. Set screw (1x) for pulley is fixed at the correct height with set screw. 6. X-axis belt tensioned properly Y-axis: 1. Bolts for stacked bearings (4x) guiding the belt are properly fixed. 2. Y-axis carriage is properly aligned in the Z-axis lift. 3. Bolts (4x) of the Y-axis carriage are properly fixed. 4. Y-axis belt pushed fully into bracket and tensioner. 5. Belt remains at same height during moving the Y-axis. 6. Set screw (1x) for pulley is fixed at the correct height with set screw. 7. Y-axis belt tensioned properly. Z-axis: 1. Z-axis rail is properly aligned. 2. Bolts (3x) Z-axis rail are properly fixed. 3. Set screw (1x) Z-axis spindle is properly fixed. 4. Bolts (4x) connecting Z-axis carriage to the lift are propely fixed. 5. Z-axis spindle nut is properly fitted in the Z-axis lift. 6. Z-axis spindle is greased over its entire length. Build Platform: 1. Bolt (1x) center of build platform is properly fixed. 2. Build surface doesn t contain air bubbles. Print Head: 1. Extruder drive wheels properly aligned. 2. Bolts (2x) connecting print head to X-axis carriage are properly fixed. 3. Bolts (2x) sensor bracket are properly fixed. Electrical: 1. Wire harness properly fixed without rubbing against parts. 2. Wire harness loop for X, Y, Z-axis are at the correct length and do not get pulled under full extension. 3. Cables are not under tension and have enough slack. 4. Cable ties neatly cut off. 5. Connectors properly connected in sockets. 6. Potentiometers on control board are set to the correct values. 7. Control board contains the correct Tec 4 firmware version. 8. Wire colors are according to diagram. Online Test: 1. Build platform heats up to 90 degrees C, move cable harness to check for wire breakage. 2. Extruders heat up to 90 degrees C, move cable harness to check for wire breakage. 3. Hot-ends don t move during loading/unloading filament. 4. Check if filament gets pulled through firmly. FELIXprinters Assembly Manual for the FELIX One Page 38

Congratulations! You have finished building the FELIX One. Continue to the Quick Start Guide to start printing! FELIXprinters Assembly Manual for the FELIX One Page 39

Bill of Material Bolts and nuts set Part Quantity #140 011.0 Set screw D-916 - M3 x 6-N - 5 #140 012.0 Bolt D-7991- M3 x 6 --- 6N - CSK 5 #140 013.0 Bolt D-7991- M3 x 8 --- 8N - CSK 15 #140 016.0 Hexagon socket head cap screw DIN 912 - M3 x 12 5 #140 017.0 Hexagon socket head cap screw DIN 912 - M3 x 16 14 #140 018.0 Hexagon socket head cap screw DIN 912 M4 x 12 12 #140 019.0 Hexagon socket head cap screw DIN 912 M4 x 16 2 #140 020.0 Hexagon socket head cap screw DIN 912 M4 x 20 7 #140 021.0 Hexagon socket head cap screw DIN 912 M4 x 25 4 #140 022.0 Hexagon socket head cap screw DIN 912 M4 x 40 2 #140 023.0 Hexagon socket head cap screw DIN 912 M5 x 16 5 #140 024.0 WasherD-125A M3 6 FELIXprinters Assembly Manual for the FELIX One Page 40

#140 025.0 WasherD-125A M4 10 #140 026.0 WasherD-125A M5 5 #140 028.0 Corrosserie ring - M4 - large washer 2 #140 029.0 Prevailing torque type hexagon nut DIN-985 - M3 6 #140 030.0 Prevailing torque type hexagon nut DIN-985 - M4 6 #140 031.0 Hexagon Thin Nut D-439B - M4 8 #140 032.0 Powersupply screw UNC 6/32 x 1/4 Pozi steel 6 #140 037.0 Set screw D-916 - M4 x 30 2 #140 039.0 Spring Extruder & bed 4 #140 040.0 Thin square nut DIN 562 - Steel - M4 9 #110 021.0 t_slot nut - 8 ST M3 3 #140 070.0 Parker 2.2 x 8 - plaatschroef 6 FELIXprinters Assembly Manual for the FELIX One Page 41

Prod. Nr. Desciption Total Image 105 021.0 Electronics bag 150 155.0 Opto sensor X (Straight), cable and connectortec4 1 150 156.0 Opto sensor Y (Angled) cable + connector Tec4 1 105 028.0 Z-sensor calibration unit 1 150 159.0 Double fan with cable and connector Tec4 1 FELIXprinters Assembly Manual for the FELIX One Page 42

170 013.0 cable ties, tie wrap - 100mm x 2.5 mm 1 170 021.0 Cable ties for mounting cables on Z bracket 2 170 015.0 Cable sleeve, nylon semi open set 95/ 115 cm 2.1 150 150.0 Stepper Extruder0 cable Tec4 1 150 152.0 Stepper X-axis cable Tec4 1 FELIXprinters Assembly Manual for the FELIX One Page 43

150 153.0 Stepper Y-axis cable Tec4 1 150 154.0 Stepper Z-axis cable Tec4 1 Prod. Nr. Desciption Total Image 105 020.0 Mechanic bag felix Tec4 135 004.0 Pulley motor - FELIX 3 and Pro series 2 135 003.0 Tooth Belt 1 135 005.0 bearing 624, 4x13x6 (packaged per 10) 7 130 016.1 Extruder drive wheel FELIX 3/Tec4 1 FELIXprinters Assembly Manual for the FELIX One Page 44

130 035.0 platform support Felix Tec4 (Y-Bracket F3.5) 1 130 041.0 Knurled thumb knob tec4 2 130 043.0 Z-adjustment right hot-end 1 130 042.0 Fan finger guard 40x40 mm tec4 2 130 044.0 Dual Extruder Front Bracket - Tec 4 1 160 017.0 Spacer rail and extruder wheel adjustment for Felix3.X 1 FELIXprinters Assembly Manual for the FELIX One Page 45

Prod. Nr. Desciption Total Image Parts packet separately in DIY kit 150 023.0 Powersupply - FELIX 3.0 1 130 017.0 Spindle - trapezium - Felix 3 1 105 127.0 Assy build platform Felix Tec4 1 135 001.0 Hiwin linear ball bearing - MGN12H1R0300Z1HM 2 135 002.0 Hiwin linear ball bearing - HGW15CC1R300Z0 1 FELIXprinters Assembly Manual for the FELIX One Page 46

Prod. Nr. Desciption Image 105 047.0 Set plastic parts 122 012.0 X_stage_F3_0_belt_mount_v1 - black 1 105 064.0 Y stage bracket prt1 with inserts Felix Tec4 Black 1 105 065.0 Y stage bracket prt2 with inserts Felix Tec4 Black 1 122 015.0 Y_stage_F3_0_tensioning_bracket_v1 - black 2 122 016.0 z_axis_f3_0_lift_part_v1 - black 1 122 017.0 z_axis_f3_0_motor_bracket_v1 - black 1 FELIXprinters Assembly Manual for the FELIX One Page 47

122 019.1 Extru_F3_1_base - black 1 122 020.1 Extru_F3_1_L_shape_bracket - black 3 122 021.0 Extru_F3_0_arm_pt1_v1 - black 2 122 022.0 Extru_F3_0_arm_pt2_v1 - black 2 122 025.0 Electronics_enclosure_F3_0_cap_pt1 - black 1 122 026.0 Electronics_enclosure_F3_0_cap_pt2 - black 1 FELIXprinters Assembly Manual for the FELIX One Page 48

122 028.0 Electronics_enclosure_F3_0_cover_plate_v1 - black 1 122 031.0 Electronics_enclosure Felix Tec4 Black 1 170 017.0 Sticker on control box, TEC 4 1 122 039.0 Fan Cap airduct Tec4 - Black 2 122 040.0 Fan front cover Tec4 - black 1 122 037.0 Printed parts LCD cabinet Felix Tec4 - Black 1 122 011.0 X_stage_F3_0_motor_bracket_v1 - black 1 FELIXprinters Assembly Manual for the FELIX One Page 49

Prod. Nr. Desciption Total Image 105 124.0 FULL metal hotend FELIX Tec 130 110.0 nozzle_felixprinters (0,35 mm pro1) 1 130 029.0 Hotend base Felix Tec4 1 130 030.0 Heat break Felix Tec4 1 150 013.0 Felix 3 & Tec 4 - Heater Cartridge incl. connector 1 130 109.0 Hot End Heated Barrel 1.75 Pro1 1 150 162.0 FELIX 3.1 & Tec4 - Thermistor incl. connector 1 130 031.0 Teflon tube Hot-end (36,5 mm) Felix Tec4 1 140 036.0 Set screw D-916 - M3 x 4 3 FELIXprinters Assembly Manual for the FELIX One Page 50

Prod. Nr. Desciption Total Image 105 051.0 Frame bag Felix3/ Tec4 110 017.0 frame connector set 6 110 018.0 handle PA 160 for Felix3 1 110 019.0 Protective cap, handle PA160, FELIX 3 1 110 022.0 T-slot nuts 8 ST M4 12 110 024.0 t_slot nut - 8 ST M8 2 110 015.0 40x40 protective caps 4 110 016.0 80x40 protective caps 1 110 025.0 damping foot (felix 3) 6 140 035.0 bolkop inbus bolt M8x16 ITEM 2 FELIXprinters Assembly Manual for the FELIX One Page 51

Prod. Nr. Desciption Total Image 105 050.0 Frame profile set Felix3/ Tec profiel 8 40x40x400 E PT1 1 profiel 8 40x40x400 E PT3 2 profiel 8 40x40x400 E PT4 1 profiel 8 80x40x440 E 1 FELIXprinters Assembly Manual for the FELIX One Page 52

Prod. Nr. Desciption Total Image 105 019.0 Miscellaneous Felix 3.1/ Tec4 150 018.0 USB cable 1.8m 1 170 011.0 Tweezers 1 170 019.1 Teflon Tube for Pro and 3 series - (55cm) 2 170 023.1 Filament dust cleaner 1 180 001.1 PLA sample - 50 gram - Random Colours 1 122 045.0 Filament guide/ dust cleaner holder Felix3/ Tec (printed) 1 122 044.0 Filament bracket Felix3/ Tec (printed) - black 2 FELIXprinters Assembly Manual for the FELIX One Page 53

Prod. Nr. Desciption Total Image Optional parts depending on region 150 019.0 Power cable EU 1 150 020.0 Power cable US 1 150 021.0 Power cable AU 1 150 022.0 Power cable UK 1 FELIXprinters Assembly Manual for the FELIX One Page 54

Optional: depending on order Prod. Nr. Desciption Total Image 105 031.0 Upgrade Single Tec to Dual Felix Tec 4 150 027.1 Stepper motor Nema 17, 40 mm 1 150 151.0 Stepper Extruder1 cable Tec4 1 130 016.1 Extruder drive wheel FELIX 3/Tec4 1 140 017.0 Hexagon socket head cap screw DIN 912 - M3 x 16 3 105 124.0 Full metal hotend FELIX Tec 1 140 039.0 Spring Extruder & bed 1 140 028.0 Corrosserie ring - M4 - large washer 2 140 018.0 Hexagon socket head cap screw DIN 912 M4 x 12 1 FELIXprinters Assembly Manual for the FELIX One Page Page 55 51

Optional: depending on order 140 031.0 Hexagon Thin Nut D-439B - M4 1 135 005.0 bearing 624, 4x13x6 (packaged per 10) 1 170 019.1 Teflon Tube for Pro and 3 series - (55cm) 1 170 023.1 Filament dust cleaner 1 105 128.0 set Tie wraps 20 pieces in bag 1 FELIXprinters Assembly Manual for the FELIX One Page 56