Proper installation of this product requires the installer to have a good understanding of automotive electronics, systems and procedures.

ENGINEERING COMPANY INC. Winthrop Road Chester, Connecticut 0-0 Phone: (0) -90 Fax: (0) -07 Internet: www.whelen.com Sales e-mail: autosale@whelen.com Canadian Sales e-mail: canadiansales@whelen.com Customer Service e-mail: custserv@whelen.com Installation Guide: Liberty and Freedom LC Lightbars Safety First This document provides all the necessary information to allow your Whelen product to be properly and safely installed. Before beginning the installation and/or operation of your new product, the installation technician and operator must read this manual completely. Important information is contained herein that could prevent serious injury or damage. Proper installation of this product requires the installer to have a good understanding of automotive electronics, systems and procedures. Automotive: Lightbars If mounting this product requires drilling holes, the installer MUST be sure that no vehicle components or other vital parts could be damaged by the drilling process. Check both sides of the mounting surface before drilling begins. Also de-burr any holes and remove any metal shards or remnants. Install grommets into all wire passage holes. If this manual states that this product may be mounted with suction cups, magnets, tape or Velcro, clean the mounting surface with a 0/0 mix of isopropyl alcohol and water and dry thoroughly. Do not install this product or route any wires in the deployment area of your air bag. Equipment mounted or located in the air bag deployment area will damage or reduce the effectiveness of the air bag, or become a projectile that could cause serious personal injury or death. Refer to your vehicle owner s manual for the air bag deployment area. The User/Installer assumes full responsibility to determine proper mounting location, based on providing ultimate safety to all passengers inside the vehicle. For this product to operate at optimum efficiency, a good electrical connection to chassis ground must be made. The recommended procedure requires the product ground wire to be connected directly to the NEGATIVE (-) battery post. If this product uses a remote device to activate or control this product, make sure that this control is located in an area that allows both the vehicle and the control to be operated safely in any driving condition. Do not attempt to activate or control this device in a hazardous driving situation. This product contains either strobe light(s), halogen light(s), high-intensity LEDs or a combination of these lights. Do not stare directly into these lights. Momentary blindness and/or eye damage could result. Use only soap and water to clean the outer lens. Use of other chemicals could result in premature lens cracking (crazing) and discoloration. Lenses in this condition have significantly reduced effectiveness and should be replaced immediately. Inspect and operate this product regularly to confirm its proper operation and mounting condition. Do not use a pressure washer to clean this product. It is recommended that these instructions be stored in a safe place and referred to when performing maintenance and/or reinstallation of this product. FAILURE TO FOLLOW THESE SAFETY PRECAUTIONS AND INSTRUCTIONS COULD RESULT IN DAMAGE TO THE PRODUCT OR VEHICLE AND/OR SERIOUS INJURY TO YOU AND YOUR PASSENGERS! For warranty information regarding this product, visit www.whelen.com/warranty 003 Whelen Engineering Company Inc. Form No.37U (000) Page

IMPORTANT! The lightbar should be a minimum of " from any radio antennas! Permanent :. Locate the mounting foot, anchor plate and locking plate included with your lightbar. If not already present, install the locking plate onto the mounting foot. When properly positioned, this plate is centered from side-to-side on the mounting foot.. Flip the lightbar upside-down to expose the bottom of the extrusion and place the mounting foot onto the extrusion. 3. Rotate the mounting foot 90 counter-clockwise. Make sure that the edges of the mounting foot swing into position under the extrusion mounting lip. Install an anchor plate onto the extrusion in the same manner.. Repeat this procedure for the remaining mounting foot and anchor plate and return the lightbar to its right side-up position.. Position the lightbar onto the vehicle roof in the desired mounting location. One often selected location is directly above the B-pillars. This area is the strongest part of the roof. Refer to your lightbar manual for cable exit location, to be sure that the lightbar is facing the proper direction.. Adjust the two mounting feet outwards so that they are as close to the edge of the roof as possible. Both mounting feet must be in full contact with the roof. Be sure that there is no less than / clearance between roof and lightbar at their closest point. When the mounting feet are in their proper position, lightly tighten the locking plate allen head set screws. 7. Return the lightbar to an upside-down position. Slide each anchor plate outwards until it is fully engaged with its corresponding mounting foot. With the mounting feet and anchor plates in their proper positions firmly tighten all of the set screws ( or per side). Flip the lightbar right side-up and return it to its mounting position.. Open both drivers side doors. In the area directly below the mounting foot, pull the weather-strip away from the vehicle so the area where the mounting strap will be secured is exposed. Repeat for the other side. 9. Insert the mounting strap through the mounting foot. Be sure that the strap fits flush against the area where it will be secured onto the vehicle. Insert the tension bolt through the mounting strap and anchor plate, into the Strap :. Locate the mounting foot, anchor plate and locking plate included with your lightbar. If not already present, install the locking plate onto the mounting foot. When properly positioned, this plate is centered from side-to-side on the mounting foot.. Flip the lightbar upside-down to expose the bottom of the extrusion and place the mounting foot onto the extrusion. 3. Rotate the mounting foot 90 in a counter-clockwise direction. Make sure that the edges of the mounting foot swing into position under the extrusion mounting lip. Install an anchor plate onto the extrusion in the same manner.. Repeat this procedure for the remaining mounting foot and anchor plate and return the lightbar to its right side-up position.. Position the lightbar onto the vehicle roof in the desired mounting location. One often selected location is directly above the B-pillars. This area is the strongest part of the roof. Refer to your lightbar manual for cable exit location, to be sure that the lightbar is facing the proper direction.. Adjust the two mounting feet outwards so that they are as close to the edge of the roof as possible. Both mounting feet must be in full contact with the roof. Be sure that there is no less than / clearance between roof and Standard Base Washer Pad Bolt Pad Washer Locking Plate Adjustable tinnerman nut. Tighten slightly with a long-shafted, Phillips screwdriver. Repeat procedure for passenger side. 0. If your mounting strap has mounting holes in the end of the strap, use these holes as a template to drill appropriately sized pilot holes through the strap and into the vehicle. Repeat for passenger side of the vehicle.. Firmly tighten the tension bolts to secure the lightbar to the vehicle. lightbar at their closest point. When the mounting feet are in their proper position, lightly tighten the locking plate allen head set screws. 7. Return the lightbar to an upside-down position. Slide each anchor plate outwards until it is fully engaged with its corresponding mounting foot. With the mounting feet and anchor plates in their proper positions firmly tighten all of the set screws ( or per side). Flip the lightbar right side-up and return it to its mounting position.. Open both drivers side doors. In the area directly below the mounting foot, pull the weather-strip away from the vehicle so the area where the mounting strap will be secured is exposed. Repeat for the other side. 9. Insert the mounting strap through the mounting foot. Be sure that the strap fits flush against the area where it will be secured onto the vehicle. Insert the tension bolt through the mounting strap and anchor plate, into the tinnerman nut. Tighten slightly with a long-shafted, Phillips screwdriver. Repeat procedure for passenger side. 0. If your mounting strap has mounting holes in the end of the strap, use these holes as a template to drill appropriately sized pilot holes through the strap and into the vehicle. Repeat for passenger side of the vehicle.. Firmly tighten the tension bolts to secure lightbar to vehicle. Insert foot into extrusion with locking plate attached. Twist mounting foot into position Loosely secure foot and locking plate. ANCHOR PLATE Page

NOTE: Model MKAJ is an adjustable mounting foot. On this model you may loosen the screws on the rear of the foot and adjust the angle of the lightbar. This feature can be used if the angle of the roof is not level with the road. IMPORTANT: To adjust the leveling screws you must use a torque wrench set at 3 to 0 in./lbs. Adjustable Model MKAJ Tension Bolt Strap Locking Plate Anchor Plate Tinnerman Model MKAJ Locking Plate Anchor Plate Standard Model MKEZ Tinnerman Screw Lock Washer Tighten screws with torque wrench set at 3 to 0 in/lbs Adjustment screws Pad Allen screws Base Screw Tension Bolt Strap " SHEET METAL SCREWS METAL SCREW BOLT STRAP MOUNTING FOOT EXTENSION NUT SPLIT LOCK WASHER NOTE: The mounting straps are made to fit the contours of individual NOTE: vehicles. The strap shown here is for example only. The strap NOTE: for your vehicle may look different. If your lightbar has a " NOTE: mounting foot, it will assemble differently than the standard NOTE: mounting foot. It also uses an extension to compensate for NOTE: the extra height. Follow these illustrations for assembly. NOTE: to the lightbar is the same. TINNERMAN NUT FOOT ANCHOR PLATE VEHICLE ROOF Plate slides into lightbar extrusion SET SCREW IMPORTANT: For strap mounted bars, be sure you have the right sized lightbar for your vehicle. The lightbar should be about the same width as the vehicle roof. If the lightbar is too large or small it will not mount properly to the vehicle and may shift or come loose during driving. /" Minimum Clearance at Closest Point NOTE: Unless otherwise specified, the lightbar mounting feet must be sitting as close to the edge of the roof as possible. feet must also be in full contact with the roof and not be hanging off the edge. Routing your Lightbar Cable(s). To protect the headliner from damage caused by drilling the cable access hole through the vehicle roof, allow a to 7 distance between roof and headliner by lowering the headliner before drilling. For lightbars with cables exiting the Driver-side of the extrusion DRILLING THE CABLE ACCESS HOLE OF LIGHTBAR For lightbars with cables exiting the Passenger-side of the extrusion Drill cable access hole in appropriate area for your lightbar (see note) WARNING! There may be a roof support member that spans the distance between the driver s and passenger s side. DO NOT DRILL THROUGH THIS MEMBER! Adjust the location until the hole can be drilled without contacting this support member.. Using a hole saw, drill the cable access hole. Use a round file to smooth and de-burr the edges than insert a grommet. 3. Insert the cable(s) through the cable access hole into the vehicle. Use RTV silicone to weatherproof the access hole after the cable(s) are pulled completely into the vehicle.. Route the cable(s) through the vehicle following manufacturers recommendations. WARNING: Many vehicles are now equipped with side curtain and B- pillar air bags. Alternate routing may be required. Page 3

Connecting the Cables: WARNING! All Customer supplied wires that connect to the positive terminal of the battery must be sized to supply at least % of the maximum operating current and FUSED at the battery to carry that load. DO NOT USE CIRCUIT BREAKERS WITH THIS PRODUCT! Power Cable:. Open the wiring shield lid and route the power cable into the wiring shield and towards the firewall. Make sure you do not to pinch or crush any wires when running them through the wire shield.. Follow the factory wiring harness through the firewall. It may be necessary to drill a hole in the firewall. If so, be absolutely sure that there are no components that could be damaged by drilling. After the hole has been drilled, insert a grommet to protect the cable. 3. Route the cable along the factory wiring harness to the battery.. Install a 30 amp fuse block (customer supplied) on the end of the wire in the power cable. Remove the fuse from the fuse block before connecting any wires to the battery.. Connect the fuse block to the POSITIVE (+) terminal on the battery. There can not be more than two feet of wire between the fuse block and the battery. The wire between the fuse block and the battery is unprotected, do not allow this wire to touch any other wires.. Connect the BLACK wire to the factory chassis ground. Cruise Lights & AUX (WHITE/): The WHITE/ wire operates in one of 3 different modes. Selecting a mode is controlled with the Scan-Lock wire. Using Scan-Lock (See Scan- Lock ), change between the 3 available modes as though you were changing flash patterns. The three modes are as follows: MODE (Default) - Cruise Lights in Low Power and the AUX port is activated. MODE - Cruise Lights in High Power and the AUX port is activated. MODE 3 - Cruise Lights are not activated and the AUX port is activated. Hi/Low Power (VIOLET): The type of switch used is dependant on how the operator wishes the Hi/Low feature to function: Latching Mode: By applying + VDC voltage to the VIOLET wire for less than second, the lightbar is latched into low power operation. The unit must be turned off and then back on to restore normal, high power operation (a momentary switch is preferred). Level Mode: Applying + VDC voltage to the VIOLET wire for more than second holds the lightbar in low power mode until voltage is removed (a toggle switch is preferred). IMPORTANT NOTE: The corner modules in your lightbar do not switch to low power when this option is applied. They will always remain in normal high power. Scan-Lock (WHITE/VIOLET): TO CYCLE FORWARD THROUGH AVAILABLE PATTERNS: Activate ONLY the control wire of the function you wish to effect and apply + volts to the Scan-Lock wire (WHITE/VIOLET) for less than second and release. This will change the pattern. For example, to change the Front Outboard LED pattern, apply +VDC to the /WHITE wire and then momentarily apply +VDC to the WHITE/VIOLET wire. Repeat until the desired pattern is displayed. Let this pattern run for seconds to configure it as the pattern the Front Outboard LEDs will display when activated. Important: Only ONE function may be active while changing patterns. Repeat for next pattern. TO CHOOSE A PATTERN: Allowing the desired pattern to run for more than seconds makes it the default pattern. TO RESET TO THE FACTORY DEFAULT PATTERN: Turn off all lightbar functions. Apply + volts to the Scan-lock wire and turn the appropriate function back on and it is now restored to its factory default pattern. Available Flash Patterns: Front Corner, Rear Corner, Outboard Inboard and Center. SignalAlert 7. CometFlash 7 3. DoubleFlash 0. DoubleFlash 7. SingleFlash 37. SingleFlash 0 7. SingleFlash 7. ActionFlash 0 9. ModuFlash 0. ActionScan Front Outboard, Inboard and Center. SignalAlert 7. CometFlash 7 3. DoubleFlash 0. DoubleFlash 7. SingleFlash 37. SingleFlash 0 7. SingleFlash 7. ActionFlash 0 9. ModuFlash 0. Steady/SF7. Steady/Steady. ActionScan Take-Down / Alley. T-D & Alley - SingleFlash 0 ALT. T-D & Alley - DoubleFlash 0 ALT 3. T-D only - SingleFlash 0 SIM. T-D only - DoubleFlash 0 SIM Traffic Advisor Sequence. Seq to Solid. Seq On - Seq Off 3. One Lamp Triple. Two Lamp Triple Control Cable: Extend the control cable to your switch panel and make your connections using the information provided. The control cable connects to your control head or switch box and is fused there. Applying +VDC to a control wire activates its function. Fuse as noted below. Wire Color Function Fuse......Front Corner LEDs...... AMP.......Rear Corner LEDs...... AMP GRN/WHT....Front Outboard LEDs.... AMP BLU/WHT....Rear Outboard LEDs.... AMP GRN/BLK....Front Inboard LEDs..... AMP BLU/BLK....Rear Inboard LEDs..... AMP Special Order Lightbars: Unicor Lightbar: Wire Color Function Fuse....All Front LEDs............ AMP.....Rear LEDs / -.... AMP VIOLET....Flashing Ctr & Alleys... AMP..Take Downs.............. AMP GREY.....Rear AMBER............. AMP...Passenger Alley........... AMP WHITE....Driver Alley............... AMP WHT/BLK..Steady Center........ AMP WHT/GRN... Right TA.............. AMP WHT/BLU... Flashing Alley & T.D. s... AMP... Pass.-Side Alley Lights... AMP WHITE..... Driver-Side Alley Lights... AMP WHT/BLK... Take-Down Lights....... AMP WHT/ORG.. Cruise Lights & AUX..... AMP WHT/..... Left TA............. AMP Philadelphia Lightbar: BLU/BLK... End External Pods....... AMP WHT/... Front External Pods...... AMP WHT/BRN.. Rear External Pods....... AMP... Passenger Alleys........ AMP WHITE..... Driver Side Alleys........ AMP..... Front Corners........... AMP...... Rear Corners........... AMP GRN/WHT.. Front Outboards......... AMP BLU/WHT... Rear Outboards......... AMP GRN/BLK... Front Outboards......... AMP WHT/BLU... Flashing Alley & TDs...... AMP WHT/BRN.....Rear Center LEDs... AMP VIOLET.......Hi/Low Power.... 0. AMPS WHT-VIO......Scan-Lock......0. AMPS WHT/......Front Center LEDs... AMP NONE.........RFI shield drain / to ground Activating WHT/GRN + WHT/ = Split TA WHT/BLK.. TakeDowns............. AMP WHT/ORG.... Cruise Lts. & AUX...... AMP VIOLET...... Hi-Low Power........ 0. AMP WHT/VIO..... Scan-Lock......... 0. AMP WHT/GRN.... Right TA.............. AMP WHT/..... Left TA............... AMP Activating WHT/GRN + WHT/ = Split TA Leader Lightbar:...... Front Corner LEDs...... AMP GRN/WHT.... Front Outboards........ AMP GRN/BLK..... Front Inboards......... AMP WHT/.... Front Center LEDs...... AMP Page

Servicing: Freedom Lightbar LR- Take-down and Alley Light Secure lighthead bracket to extrusion Lightheads to Extrusion Ears on lighthead bracket slide into channels in extrusion (base). BASE LIGHTHEAD LR TAKEDOWN Servicing: Liberty Lightbar SUPPORT BRACKET BASE LR ALLEY LIGHT LR- Take-down Snap lighthead bracket into TD bracket Lighthead mounting holes snap into the raised bosses on the lighthead bracket. SECURE TO TO SECURE BRACKET Endcap, Gasket, Lenses & Spacers Installation Gasket & Halogen Alley Light BOSS BARB Align lighthead reflector up with bosses in endcap. Press reflector into place. BASE SIDE VIEW Extrusion secures to Support Bracket. Halogen Lighthead snaps into extrusion Snap lighthead into bracket. Remove the screws (A) that hold the endcap (B) on and pull the endcap and gasket (C) off. Slide lenses (D) out of the lightbar, to gain access to the extrusion. When reinstalling the lenses and spacers, install the cord seal (NFPA / See below). When reinstalling the endcap, place the endcap gasket into it's position on the endcap and line up all the tabs and holes. Spacers (not shown) mount the same as lenses. Seal Cord Installation / NFPA Only: -Cut the seal cord approx. -/" longer than the extrusion on each side. -Rub silicone over the cord seal leaving 3 to inches on one end dry. 3-Begining with corner lens, start the lens into the bottom 3-lens track. Place the cord seal onto the groove in the 3-top of the lens. Leave to inches free. D -Hold onto the left end of the seal hanging -out and slide the corner lens into -position. -From the opposite end of the -lightbar, pull the seal -cord tight and install -the remaining lenses -and divider. A B Installing Lens and Lighthead Lens fits here SUPPORT BRACKET C Insert cord seal into track in lens -Inspect seal cord for any areas that have wrinkled. -Especially in the areas around the dividers. 7-Push the lenses together tight and trim excess seal 7-cord at each end. D NOTE: Lens dividers must be installed as each lens is put into position Installing Corner Linear-LED Lens Screw Slide into tracks in extrusion ADJUST ANGLE Halogen Lighthead slides into extrusion here. BASE Halogen Alley Light If lightbar has no alley light, use nuts to hold lens in. CENTER OF BASE #-3 elastic stop nut Threads onto lens screw if no lighthead is present. LR- Alley Light Endcap & Gasket 00 Series Alley Light MR- with TIR3 Alley Light Plasti-Loc Screw Lens Insert the tabs on the lighthead housing, into the channels in the extrusion. Page Endcap

3 3 37 WHT/ 9 REAR LED REAR LED REAR LED 3 REAR LED REAR LED REAR LED REAR OF LIGHTBAR 3 7 WHT DRIVER'S SIDE 7 9 WHT/ WHITE / BLACK LED LED LED 3 LED LED LED QTY QTY QTY QTY ITEM PART NUMBER DESCRIPTION 0-0- 0-0- 0-0- 0-0- Freedom Ext LC R/R/B/B 0" Freedom Ext LC R/R/B/B " Freedom Ext LC R/R/B/B 0" Freedom Ext LC R/R/B/B " -33-000 BASE (.7") -33-000 BASE (.") 3-333-000-070-00 BASE (.0") MTG. STUD 7-0-000-077-7-073-7 BUSHING, -/" CABLE, /C 0GA 7' CABLE, 7/C GA 7' 9 0-0739-00-00- HARNESS, LIGHT GROMMET,." -0-JB #0- x -/" TX. PHD. SCREW W/SHLDR 3-0-03 NUT, #0- WHIZ -03-0 CABLE CLAMP, /" 7 39-00303-0 0-09-00 HOUSING, 3 POS SOCKET ASSEMBLY, I/O BOARD LC 0 3-30-07-09-00 NUT, /-0 ELASTIC STOP (3 SS) PROTECTIVE COVER 3-7399-00-073-00 0-03-30 VENT, 3/" LIGHT HARNESS 0" LENS DIVIDER ASS'Y. (CLEAR) 0-0307-0 LABEL, MODEL & SERIAL NO. 0 07-303-000 09-33-00 MOUNTING BRACKET FILLER PANEL, "00" SERIES 7-0-0 #0- x PPHMS 0-0C3-30 SINGLE LR ALLEY FREEDOM 39-033-0 HOUSING, POS SCKT. CMNL 30-93-30 LENS,.00" CLEAR 3 3 33-937-30-90-30 07--000 LENS,." CLEAR LENS, 9." CLEAR BRACKET, SPACER 3 3 3 3-033-00-339-30 39-007-0 GASKET, ENDCAP ENDCAP, CLEAR HOUSING, POLE 37-0739-00 HARNESS, LIGHT 7" 3 39-33390-000-39C0 BASE (0.37") LENS, 0.37" CLEAR 0-90-30 LENS,.7" CLEAR 0-0B00 CORNER REFLECTOR LED AMBER 0-0B00 CORNER REFLECTOR LED 3 0-0B0330 CORNER REFLECTOR LED WHITE 0-0B00 CORNER REFLECTOR LED 0-0B00 CORNER REFLECTOR LED -07397-00 HARNESS, ALLEY LIGHT 7 0-0393-00 LABEL, "" 0 GRAY WHT/ORG 0 3 WHT/BRN LR ALLEY PASSENGER SIDE 7 3 30 39 0 39 3 3 3 3 3 33 7 Page

- 9-7 - 7 9 0 73 7 3 7 7 QTY QTY QTY QTY ITEM PART NUMBER DESCRIPTION 3 7 9 0 7 0 3 3 33 3 3 0-09-0 0-09-3 0-09- 0-09-03-33-000-33-000-333-000-070-00-0-000-077-7-073-7 0-0B07-0 0-0B07-0 -00- -0-JB #0- x -/" TX. PHD. SCREW-SHLDR 3-0-03-03-0 39-00303-0 0-09-00 0-0339-00-93-30-937-30-90-30 Freedom Gen 3 LC R/R/B/B 0" Freedom Gen 3 LC R/R/B/B " Freedom Gen 3 LC R/R/B/B 0" Freedom Gen 3 LC R/R/B/B " BASE (.7") BASE (.") BASE (.0") MTG. STUD BUSHING, -/" CABLE, /C 0GA 7' CABLE, 7/C GA 7' CORNER REFLECT. LED CORNER REFLECT. LED BLU GROMMET,." NUT, #0- WHIZ CABLE CLAMP, /" HOUSING, 3 POS SOCKET ASSEMBLY, I/O BOARD LC 3-30-07 NUT, /-0 ELASTIC STOP (3 SS) -09-00 PROTECTIVE COVER 0-03 LINEAR LED 00 GRN GEN III AMP 0-03 LINEAR LED 00 BLU GEN III AMP 0-03 LINEAR LED 00 GEN III AMP 0-0333 LINEAR LED 00 WHT GEN III AMP 0-03 LINEAR LED 00 AMB GEN III AMP 0-03-30 LENS DIVIDER ASS'Y. (CLR) 7 0-0307-0 LABEL, MODEL & SERIAL NO. 07-303-000 MTG BRACKET 0 09-33-00 FILLER PANEL, "00" SERIES 30-0-0 #0- x PPHMS 3 0-007-00 SPACER, CORNER STROBE REFLECTOR 00 HALOGEN LENS,.00" CLEAR LENS,." CLEAR LENS, 9." CLEAR 3 07--000 BRACKET, SPACER 37 3-033-00 GASKET, ENDCAP 3 39 0-339-30 39-007-0-0739-00 ENDCAP, CLEAR HOUSING, POLE HARNESS, LIGHT 7" -33390-000 -39C0 BASE (0.37") LENS, 0.37" CLEAR 3-90-30 LENS,.7" CLEAR -0739-00 HARNESS, LIGHT 9-07397-00 HARNESS, ALLEY LIGHT 0-07379-00 HARNESS, "Y" LR 39-033-0 HOUS., POS SCKT CMNL 3-7399-00-0730-00-073-7 39-00- -07397-0 VENT, 3/" HARNESS, TA CABLE, 9/C 7' HOUSING, POS CMNL HARNESS, TAKE DOWN 7 0-039-00 SUB ASSY, MR/TIR3 ALLEY 0-03B9A TIR3 LED STDY AMB VERT AMP 9 0-03B9B TIR3 LED STDY BLU VERT AMP 0 0-03B9C TIR3 LED STDY WHT VERT AMP 0-03B9R -070-00 TIR3 LED STDY VERT AMP HARNESS "Y" 3-073-00 0-030 0-03 0-033 LIGHT HARNESS 0" LED 00 SPLIT / GEN III AMB/NONE/AMP LED 00 SPLIT / GEN III AMB/BLU/AMP LED 00 SPLIT / GEN III AMB/WHT/AMP 7 0-03 LED 00 SPLIT / GEN III AMB//AMP 0-03A0 LED 00 SPLIT 3/3 GEN III AMB/NONE/AMP 9 0-03AB LED 00 SPLIT 3/3 GEN III AMB/BLU/AMP 70 0-03AR LED 00 SPLIT 3/3 GEN III AMB//AMP 7 0-03A LED 00 SPLIT /3 GEN III BLU/AMB/AMP 7 0-03A LED 00 SPLIT /3 GEN III /AMB/AMP 73 0-0A93-00 SUB ASSY, DUAL LR TD 7 0-0A93-0 SUB ASY, DUAL LR TD 00lm 7 0-0B07-30 SUB ASY, DUAL LR ALLEY 7 0-0B07-3 SUB ASY, DUAL LR ALLEY 00lm Rear of Lightbar 0 ORG BRN 0 3 BLU / REAR LED GRN / REAR LED / REAR LED ORG / REAR LED 3 0 / REAR LED BRN / REAR LED RT BRN 9 WHT 39 9 GRY TD ALLEY AUX BLU / LED GRN / LED REAR I.O. CARD ASSEMBLY ("LC" SERIES) 7 Cable EXIT / LED ORG / LED 3 / LED BRN / LED 3 3 POS. CONN. P- WHT- P- WHT-GRN P3- N/C POS. CONN. P9- GRN P- VIO P0- WHT-BRN P- GRN-BLK P- BLU-WHT P3- GRN-WHT P- P- BLU-BLK P3- BLU P- WHT-BLU P- WHT P- WHT-ORG P- SHIELD P7- WHT-VIO P- WHT-BLK P- WHT- 0.00 WHT/ BLK ORG 37 3 3 3 3 37 7. 3 3 0 30 INPUT CABLE DETAIL.37 33 Page 7 37 3 3 9.70 3 3 3 37 3 3

7 7 3 LED LED LED LED 3 LED LED 7 RTD LTD 9 7 OF " LIGHTBAR ENDCAP LED PASSNGR ("LC" SERIES) I.O. CARD ASSEMBLY DRIVER LA ORG RA 3 BRN 9 IAL ITD WIRE REAR 7 0 LED LED LED LED 3 LED LED 3 BRN 0 3 3 3 0 3 0 OF LIGHTBAR 7 37 37 39 0-73 3-7 7 Endcap Detail with Alley Endcap Detail no alley 39 7 3 9 70 7 7 73 7 7 79 30 77 QTY QTY QTY ITEM PART NUMBER DESCRIPTION 0-09-09 Liberty Gen 3 LC B/B/B/B 3" 0-09-3 Liberty Gen 3 LC R/R/B/B " 0-09- Liberty Gen 3 LC R/R/B/B " -00- GROMMET,." -077-7 INPUT CABLE (C-0GA.) 7' 3-0-03 #0- WIZ NUT -03-0 CABLE CLAMP, /" -00337-00 SCREW, 0- x." TX PHD. 9 39-007-0 HOUSING, POLE 0 39-00303-0 HOUSING, 3 POS. AMP SOCKET -7399-00 PLUG, VENT (3/") -333-0, BASE " W/HOLES -073-00 HARNESS, CORNER L.E.D. (LIBERTY) -093330-00 HARNESS, INBOARD L.E.D. (LIBERTY) 7-0737-0 HARNESS, TAKE DOWN (LIBERTY) -0737-03 HARNESS, ALLEY LIGHTS (LIBERTY) 0 0-3-000 HOUSING, LIGHTHEAD (SNAP-IN) 0-0979-00 ASS'Y., I.O. CARD "LC" 0-03377-03 SUB-ASS'Y., 00 HALOGEN W/3POS. 3 0-0B70 SUB-ASS'Y., 00 LED, AMBER, W/POS. 0-0B70 SUB-ASS'Y, 00 LED, W/POS 0-0B730 SUB-ASS'Y., 00 LED, CLEAR, W/POS. 0-0B70 SUB-ASS'Y., 00 LED,, W/POS. 0 7 09-33-00 PANEL, FILLER (00 SERIES) -9337-30 LENS, 00 SERIES, OPTIC (CLEAR) 0-007-00 SPACER, CORNER RETENTION 30-0-0J #0- X 3/ PPH SCREW 3-0-JB #0- X -/" TX. PHD. W/SHOULDER 3 3-037-00 GASKET, ENDCAP 33 0-0379-30 ASS'Y., LENS DIVIDER (CLEAR) 3 3-073-00 INSULATOR, FOAM PAD 3 -B07-0, TOP " 37-00-00 # X /" PPH PLASTI-LOC SS 3 0-0393-00 LABEL, "" LIGHTBAR ASS'Y. 39-3-3S LENS, ENDCAP (CLEAR) W/SEAL 0-939-30 LENS,.7" LG. (CLEAR) -93333C0 LENS,.37" LG. (CLEAR) -937-30 LENS,.00" LG. (CLEAR) 3 07-370-000 BRACKET, SPACER CORNER 0-090-00 LABEL, MODEL & SERIAL NO. -0-00 #-3 x /" PPHMS 3-00-0 #-3 ELASTIC STOP NUT 7 39-033-0 HOUSING, POS SOCKET 9 0-0B0 CORNER LED (LIBERTY) 0-0B0 CORNER LED (LIBERTY) -333-03, BASE 3." W/HOLES 7-333-09, BASE 9.39" W/HOLES -B07-03, TOP 3." 9 -B07-09, TOP 9.39" 0 0-0A79-0 SUB ASSY, LR T-D SINGLE FULL LIB. -93333C03 LENS, 0.00" LG. (CLEAR) -93-30 LENS,.0" LG. (CLEAR) 3-073-7 CABLE, 7/C GA (7') 0-0B70 SUB-ASS'Y., 00 LED,, W/POS. 7-070-00 HARNESS, "Y" 0-0B70 SUB-ASS'Y., 00 LED, AMBER, W/POS. 9 0-0B70 SUB-ASS'Y, 00 LED, W/POS. 70 0-0B730 SUB-ASS'Y., 00 LED, WHITE, W/POS. 7 0-0B70 SUB-ASS'Y., 00 LED,, W/POS. 7 0-0B70 SUB-ASS'Y., 00 LED,, W/POS. 73 0-0B7K0 SUB-ASS'Y., 00 AMBER- W/POS. 7 0-0B7M0 SUB-ASS'Y., 00 AMBER- W/POS. 7 0-0A7-0 SUB ASSY, LR TD HALF LIBERTY 7 0-0A79-0 SUB ASSY, LR T-D DUAL FULL LIB. 77 0-0B-30 SUB ASSY, LR ALLEY LT WHT 0 DEG 7 0-0B7J0 SUB-ASS'Y., 00 - W/POS. 79 0-0B7A0 SUB-ASS'Y., 00 AMB-AMB W/POS. 3 3 7 0-0A93-00 0-0A93-0 -000-0 -393-30 SUB-ASS'Y, TIR LED TD, N/OPTIC SUB-ASS'Y, TIR LED TD, OPTIC TY-WRAP, " BLACK LENS, 00 SERIES, NON OPTIC / CLR 0-03B-00 SUB ASSY, END SUPPORT BRACKET 0-0B7J0 SUB ASSY, 00 / BLU/ INTRLVD 0-0B7K0 SUB ASSY, 00 / AMB/ INTRLVD 0-0B7M0 SUB ASSY, 00 / AMB/BLU INTRLVD 3 3 9 33 Page

LED / BLU LED / GRN LED / LED 3 / ORG LED / QTY QTY QTY QTY ITEM PART NUMBER DESCRIPTION 7 9 9 0-0- Liberty Lightbar 0" LC PASSENGER'S SIDE 0-0- 0-0- Liberty Lightbar " LC Liberty Lightbar " LC 0-0- Liberty Lightbar 3" LC LED TAKEDOWN -00- GROMMET,." WORK LIGHT -077-7 INPUT CABLE, (C-0GA.) 7' 0 RA 3-93333C03 LENS, 0.00 LG (CLEAR) 3-0-03 #0- WIZ NUT -03-0 CABLE CLAMP, /" -00337-00 SCREW, 0- x." TX PHD 39-00303-0 HOUSING, 3 POSITON SOCKET (CMNL) 0-7399-00 PLUG, VENT (3/") 3-073-00 HARNESS, CORNER LED -939-30 LENS,.7" LG. (CLEAR) 3-0737-0 HARNESS, TAKE DOWN/WORK LIGHTS 07-370-000 SPACER, CORNER 39-007-0 HOUSING, POLE 0 7-3-000 HOUSING, LIGHTHEAD (SNAP-IN) 9 0-0979-00 ASS'Y, I/O CARD "LC" 7 0-093330-00 HARNESS, INBOARD LED 00 SERIES FILLER 0 09-33-00 PANEL, FILLER (00 SERIES) -0-0J #0- X 3/ PPH SCREW -0-JB #0- X -/" TX. PHD. W/SHOULDER 7 0-0379-30 ASS'Y., LENS DIVIDER (CLEAR) 7 3-073-00 INSULATOR, FOAM PAD 30 0-0393-00 LABEL, "" LIGHTBAR ASS'Y. 3 0-03A03-30 SUB ASSY, ENDCAP CLEAR 9 3-93-30 LENS,.0" LG (CLEAR) 33-93333C0 LENS,.37" LG. (CLEAR) 3-937-30 LENS,.00" LG. (CLEAR) 3 0-090-00 LABEL, MODEL & SERIAL NO. 3 0-0B930 EXTENDED, CORNER LED AMBER 39 0-0B930 EXTENDED, CORNER LED LR TAKEDOWN 0 0-0B9330 EXTENDED, CORNER LED WHITE 7 LIGHT 0-0B930 EXTENDED, CORNER LED 0-0B930 EXTENDED, CORNER LED 3-333-0 BASE, EXTRUDED (.7") -333-09 BASE, EXTRUDED (9.39") -333-0 BASE, EXTRUDED (.00") -333-03 BASE, EXTRUDED (3.") 7 -B07-0 TOP, EXTRUDED (.7") -B07-09 TOP, EXTRUDED (9.39") 9 -B07-0 TOP, EXTRUDED (.00") 0 -B07-03 TOP, EXTRUDED (3.") 39-033-0 HOUSING, POS SOCKET 0 3-07379-00 HARNESS, "Y" -0737-03 HARNESS, ALLEY LIGHT -073-7 CABLE, 7/C GA (7') 0 0-0B-30 SUB-ASS'Y, ADJ. LR- ALLEY LIGHT 7 0-0B-0 SUB-ASS'Y, ADJ. LR- ALLEY LT AMBER 0-0B-0 SUB-ASS'Y, ADJ. LR- ALLEY LT 9 0-0B-0 SUB-ASS'Y, ADJ. LR- ALLEY LT 0 0-03A93-00 SUB-ASS'Y, TIR TAKE-DOWN NON OPTIC 0-0B70 SUB-ASS'Y, 00 LIN AMBER 3 0-0B70 SUB-ASS'Y, 00 LIN 3 0-0B730 SUB-ASS'Y, 00 LIN WHITE 0-0B70 SUB-ASS'Y, 00 LIN 0-0B7J0 SUB-ASS'Y, 00 LIN /BLU 3 0-0A7-0 SUB-ASS'Y, LR- TAKEDOWN LT HALF 70 3 3 7 0-0A79-0 SUB-ASS'Y, LR TAKEDOWN FULL SINGLE 0-0A79-0 SUB-ASS'Y, LR TAKEDOWN FULL DUAL 7 39 9 0-03B-00 SUB ASSY, END SUPPORT BRACKET 7 0 70 0-0B930 EXTENDED, CORNER LED AMBER 73 7 0-0B930 EXTENDED, CORNER LED 7 7 0-0B9330 EXTENDED, CORNER LED WHITE 73 0-0B930 EXTENDED, CORNER LED DRIVER'S SIDE 7 0-0B930 EXTENDED, CORNER LED 7 9 0 3 3 30 3 3 7 33 RTD LED / BRN LTD Front of " Lightbar LA LED LED LED LED 3 LED LED OF " LIGHTBAR 3 Page 9