INSTALLATION INSTRUCTIONS Accessory LOWER P/N 08P46-SZA-100A Application 2011 PILOT Publications No. AII 43325-45001 Issue Date SEP 2010 PARTS LIST Rear lower trim 2 Washer-nuts 2 Special bolts TOOLS AND SUPPLIES REQUIRED Stubby Phillips screwdriver Ratchet Socket Hex wrench Pushpin Drill 3 mm and 10 mm Drill bits 19 mm Hole saw Eye protection (safety goggles, face shield, etc.) Blanket Illustration of the Rear Lower Trim Kit Installed on the Vehicle 2 Washers 2 Spacers 4 Bolts Clip LOWER 7N3001AB 2010 American Honda Motor Co., Inc. All Rights Reserved. AII 43325-45001 (1009) 08P46-SZA-1A01-91 1 of 5
INSTALLATION Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by do-it-yourselfers. NOTE: Do not damage the body paint finish. To prevent damage, place a blanket under the rear bumper during the installation. 1. Remove the rear bumper (two clips, two bolts, two hex bolts, and ten self-tapping screws). Have an assistant help you when removing and installing the rear bumper. Place the rear bumper on a blanket after removal. 2. Locate the seven scribe marks, and pierce through the centers of these seven scribe marks with a pushpin. 2 SCRIBE MARKS PUSHPIN 2 SELF- PUSHPIN 5 SCRIBE MARKS 862501AX 3. Remove the left and right splash guards (four clips, four bolts, and two hooks). 2 HEX 2 CLIPS 2 8 SELF- 792603BE 4 CLIPS 4 RIGHT SPLASH LEFT SPLASH 2 HOOKS SPLASH 792701BB 2 of 5 AII 43325-45001 (1009) 2010 American Honda Motor Co., Inc. All Rights Reserved.
4. Remove the rear lower bumper (four self-tapping screws and twelve hooks). 6. While wearing eye protection, drill the three upper marks on the rear under bumper that you made in step 2. First drill with a 3 mm drill bit, then finish with a 10 mm drill bit. Remove all burrs. UNDER MARK UNDER 4 SELF- UNDER LOWER 792702BB 5. While wearing eye protection, drill the two marks on the rear bumper that you made in step 2. First drill with a 3 mm drill bit, then finish with a 19 mm hole saw. Remove all burrs. 862503AX UPPER UPPER 3 mm 19 mm HOLE SAW 862502AX 2010 American Honda Motor Co., Inc. All Rights Reserved. AII 43325-45001 (1009) 3 of 5
7. While wearing eye protection, drill four lower marks on the rear under bumper that you made in step 2. First drill with a 3 mm drill bit, then finish with a 10 mm drill bit. Remove all burrs. 8. Position the rear lower trim on the rear under bumper, and install two washer-nuts, two washers, two spacers, and two special bolts as shown. Torque the special bolts to 4 N m (3 lbf ft). 2 SPECIAL LOWER 2 WASHERS UNDER 2 WASHER- NUTS 2 SPAC- UNDER UNDER UNDER 862504AX 862505AX 9. Secure the rear lower trim to the rear under bumper with four bolts. 4 UNDER LOWER 862506BX 4 of 5 AII 43325-45001 (1009) 2010 American Honda Motor Co., Inc. All Rights Reserved.
10. Reinstall the rear under bumper to the rear upper bumper. 13. Reinstall the rear bumper. 2 SELF- UPPER LOWER 2 HEX 2 CLIPS 2 8 SELF- 792807BB 4 SELF- CLIP UNDER 872506AD 11. Install one clip in the rear lower trim. 12. Reinstall the left and right splash guards to the rear bumper. 4 CLIPS 4 RIGHT SPLASH SPLASH LEFT SPLASH 2 HOOKS 792806BB 2010 American Honda Motor Co., Inc. All Rights Reserved. AII 43325-45001 (1009) 5 of 5