Model Travel CV-7A CVM-7A CV-7B CVM-7B CV-9A CVM-9A CV-9B CVM-9B CV-11A CVM-11A X-axis (left and right) 760 760 900 900 1100 1100 Y-axis (back and front) 520 520 600 600 600 600 Z-axis (up and down) 480 480 600 600 600 600 CV-11B CVM-11B Distance from spindle nose to table surface 100~580 100~580 100~700 100~700 100~700 100~700 Table Table Size (X x Y) 520x860 520x860 1000 x 600 1000 x 600 1200 x 600 1200 x 600 Max. Loading Capacity kgs 300 300 650 650 800 800 T-Slots (numbers x width x pitch) no x 3 x 14 x 125 3 x 14 x 125 5 x 18 x 100 5 x 18 x 100 5 x 18 x 100 5 x 18 x 100 Speed (ST) rpm Speed (OP) rpm 12000/15000 12000/15000 12000/15000 Taper type #40 Bearing Diameter φ70 Feed Rapid Travel Rate (X/Y/Z) m/min 48/48/48 36/36/36 48/48/48 36/36/36 48/48/48 36/36/36 Cutting Rate m/min 10 Manual JOG feed rate m/min 4(20Steps) ATC Tool shank type type MAS BT-40(*CAT-40/*DIN-40) Pull stud type MAS BT-40/P40T-1 (*CAT-40/*DIN-40) Magazine capacity (ST) tools 24 (Cam type) Magazine capacity (OP) tools 32/40 (Cam type) (with ad jecent tools) φ75 (without adjecent tools) φ150 Max tool length 300 Max tool weight kgs 7 Tool change time CVM Series Without ATC System Tool to tool sec 1.2(2) 1.2(2) 2 2 2 2 Chip to Chip sec 2.7(5.8) 2.7(5.8) 3.8 3.8 3.8 3.8 Motor Motor (Cont./30min)(ST) kw 5.5/7.5 7.5/11 7.5/11 Motor (Cont./30min)(OP) kw 7.5/11 11/15(15/18.5) 11/15(15/18.5) Feed Motor X/Y/Z kw 3/3/4 3/4/7 3/4/7 Coolant motor (50/60HZ) kw 0.75 0.75 x 2 0.75 x 2 Power Supply Power Supply KVA 15 20 20 Compressed air supply Mpa, l/min 0.6, 500 0.6, 500 0.6, 500 Coolant tank capacity L 250 420 420 Controller FANUC/MITSUBISHI/SIEMENS/HEIDENHAIN External dimension Width 2100 2335 2800 Length 2660 3500 3500 Height 2630 2985 2985 Weight Kgs 3800 6750 6950 (following values were tested in the temperature-controlled room) ISO 10971 JIS 6338 Other Linear Guideway Positioning 0.009 Repeatability 0.006 Positioning (within 300) ±0.004 Repeatability (within 300) ±0.002 35 roller type linear guideway (X/Y/Z) 35 ball type linear guideway (X/Y/Z) 45 roller type linear guideway (X/Y/Z) 45 roller type linear guideway (X/Y/Z) Model CV-14B CVM-14B CV-14BH CVM-14BH CV-16B CVM-16B CV-16BH CVM-16BH CV-9A APC CV-9B APC Travel X-axis (left and right) 1400 1400 1600 1600 900 900 Y-axis (back and front) 700 700 700 700 600 600 Z-axis (up and down) 700 700 700 700 560 560 Distance from spindle nose to table surface 100~800 100~800 100~800 100~800 150-710 150-710 Table Table Size (X x Y) 1550 x 700 1550 x 700 1750 x 700 1750 x 700 850 x 500 (with 2 pallets) Max. Loading Capacity kgs 1000 1000 1000 1000 300 x 2 T-Slots (numbers x width x pitch) no x 5 x 18 x 150 5 x 18 x 150 5 x 18 x 150 5 x 18 x 150 5 x 18 x 100 Speed (ST) Speed (OP) rpm rpm /12000/15000 - /12000/15000-12000/15000 Taper type #40 #50 #40 #50 #40 Bearing Diameter φ70 φ90 φ70 φ90 φ70 Feed Rapid Travel Rate (X/Y/Z) m/min 36/36/30 (*40/40/36) 36/36/24 (*40/40/24) 36/36/30 (*40/40/36) Cutting Rate m/min 10 Manual JOG feed rate m/min 4(20Steps) ATC MAS BT-40(*CAT- 40/*DIN-40) MAS BT-50(*CAT- 50/*DIN-50) MAS BT-40(*CAT- 40/*DIN-40) 36/36/24 (*40/40/24) MAS BT-50(*CAT- 50/*DIN-50) 48/48/48 36/36/36 Tool shank type type MAS BT-40(*CAT-40/*DIN-40) Pull stud type MAS BT-40/P40T-1 MAS BT-50/P50T-1 MAS BT-40/P40T-1 MAS BT-50/P50T-1 MAS BT-40/P40T-1 (*CAT-40/*DIN-40) (*CAT-40/*DIN-40) (*CAT-50/*DIN-50) (*CAT-40/*DIN-40) (*CAT-50/*DIN-50) Magazine capacity (ST) tools 24 (Cam type) Magazine capacity (OP) tools 16,24 (umbrella) / 16,24 (umbrella) / 30/40 (Cam type) 32,40 (cam) 32,40 (cam) 30/40 (Cam type) 32/40 (Cam type) (with adjecent tools) (without adjecent tools) ATC24(φ78)/ ATC32,40(φ75) φ105(φ210) ATC24(φ78)/ ATC32,40(φ75) φ105(φ210) φ150 φ216(φ250) φ150 φ216(φ250) φ150 Max tool length 300 300 300 300 300 Max tool weight kgs 7 15 7 15 7 Tool change time CVM Series Without ATC System Tool to tool sec ATC24(1.32)/ ATC32,40(1.94) 2.9 ATC24(1.32)/ ATC32,40(1.94) φ75 2.9 2 Chip to Chip sec 3.8 6 3.8 6 3.8 Motor Motor (Cont./30min)(ST) kw 7.5/11 15/18.5 7.5/11 15/18.5 7.5/11 Motor (Cont./30min)(OP) kw 11/15(15/18.5) 22/26 11/15(15/18.5) 22/26 11/15(15/18.5) Feed Motor X/Y/Z kw 4/4/7 4/4/7 4/4/7 4/4/7 3/3/7 Coolant motor (50/60HZ) kw 0.75 x 2 Power Supply Power Supply KVA 35 20 Compressed air supply Mpa, l/min 0.6, 500 0.6, 500 Coolant tank capacity L 496.5 420 Controller FANUC/MITSUBISHI/SIEMENS/HEIDENHAIN External dimension Width 2385 2385 2385 2385 2280 Length 3833 3833 4033 4033 3635 Height 3007 3074 3007 3074 3085 Weight Kgs 9540 9740 11040 11240 8300 (following values were tested in the temperature-controlled room) ISO 10971 JIS 6338 Other Linear Guideway Positioning 0.009 Repeatability 0.006 Positioning (within 300) ±0.004 Repeatability (within 300) ±0.002 45 roller type linear guideway (X/Y/Z) 45 roller type linear guideway (X/Y/Z) 45 roller type linear guideway (X/Y/Z)
Model DV-9A DVM-9A DV-9B DVM-9B DV-9C DVM-9C DV-11A DVM-11A DV-11B DVM-11B DV-11C DVM-11C Travel X-axis (left and right) 900 900 900 1100 1100 1100 Y-axis (back and front) 600 600 600 600 600 600 Z-axis (up and down) 600 600 600 600 600 600 Distance from spindle nose to table surface 100~700 100~700 100~700 100~700 100~700 100~700 Table Table Size (X x Y) 1000 x 600 1200 x 600 Max. Loading Capacity kgs 650 800 T-Slots (numbers x width x pitch) no x 5 x 18 x 100 5 x 18 x 100 Speed (ST) rpm 6000 (Gear) Speed (OP) rpm 12000/15000 7000 12000/15000 7000 Taper type #40 Bearing Diameter φ70 Feed Rapid Travel Rate (X/Y/Z) m/min 48/48/24 36/36/24 36/36/24 48/48/24 36/36/24 36/36/24 Cutting Rate m/min 10 Manual JOG feed rate m/min 4(20Steps) ATC Tool shank type type MAS BT-40(*CAT-40/*DIN-40) Pull stud type MAS BT-40/P40T-1 (*CAT-40/*DIN-40) Magazine capacity (ST) tools 24 (Cam type) Magazine capacity (OP) tools 32/40 (Cam type) (with adj ecent tools) φ75 (without adjecent tools) φ150 Max tool length 300 Max tool weight kgs 7 6000 (Gear) Model DV-9A APC DV-9B APC DV-9C APC Travel X-axis (left and right) 900 900 900 Y-axis (back and front) 600 600 600 Z-axis (up and down) 560 560 560 Distance from spindle nose to table surface 150-710 150-710 150-710 Table Table Size (X x Y) 850 x 500 (with 2 pallets) Max. Loading Capacity kgs 300 x 2 T-Slots (numbers x width x pitch) no x 5 x 18 x 100 Speed (ST) rpm Speed (OP) rpm 12000/15000 7000 Taper type #40 Bearing Diameter φ70 Feed Rapid Travel Rate (X/Y/Z) m/min 48/48/24 36/36/24 36/36/24 Cutting Rate m/min 10 Manual JOG feed rate m/min 4(20Steps) ATC Tool shank type type MAS BT-40(*CAT-40/*DIN-40) Pull stud type MAS BT-40/P40T-1 (*CAT-40/*DIN-40) Magazine capacity (ST) tools 24 (Cam type) Magazine capacity (OP) tools 32/40 (Cam type) (with adjecent tools) φ75 (without adjecent tools) φ150 Max tool length 300 Max tool weight kgs 7 6000 (Gear) Tool change time DVM Series Without ATC System Tool change time DVM Series Without ATC System Tool to tool sec 2 Chip to Chip sec 3.8 Motor Motor(Cont./30min)(ST) kw 7.5/11 Motor(Cont./30min)(OP) kw 11/15(15/18.5) Feed Motor X/Y/Z kw 3/4/3 Coolant motor (50/60HZ) kw 0.75 x 2 Power Supply Power Supply KVA 20 Compressed air supply Mpa, l/min 0.6, 500 Coolant tank capacity L 420 Controller FANUC/MITSUBISHI/SIEMENS/HEIDENHAIN External dimension Width 2335 2800 Length 3500 3500 Height 2985 2985 Weight Kgs 7750 7750 7850 7950 7950 8050 (following values were tested in the temperature-controlled room) ISO 10971 JIS 6338 Other Linear Guideway Positioning 0.009 Repeatability 0.006 Positioning (within 300) ±0.004 Repeatability (within 300) ±0.002 45 roller type linear guideway (X/Y); Box Way (Z) 45 roller type linear guideway (X/Y); Box Way (Z) Tool to tool sec 2 Chip to Chip sec 3.8 Motor Motor (Cont./30min)(ST) kw 7.5/11 Motor (Cont./30min)(OP) kw 11/15(15/18.5) Feed Motor X/Y/Z kw 3/4/3 Coolant motor (50/60HZ) kw 0.75 x 2 Power Supply Power Supply KVA 20 Compressed air supply Mpa, l/min 0.6, 500 Coolant tank capacity L 420 Controller FANUC/MITSUBISHI/SIEMENS/HEIDENHAIN External dimension Width 2280 Length 3635 Height 3085 Weight Kgs 8500 8500 8600 (following values were tested in the temperature-controlled room) ISO 10971 JIS 6338 Other Linear Guideway Positioning 0.009 Repeatability 0.006 Positioning (within 300) ±0.004 Repeatability (within 300) ±0.002 45 roller type linear guideway (X/Y); Box Way (Z)
Specification/Model CV-7A CVM-7A CV-7B CVM-7B :Standard specification :Optional specification X:Inadaptable CV-9A CVM-9A CV-9A APC CV-9B CVM-9B CV-9B APC CV-11A CVM-11A CV-11B CVM-11B CV-14A CVM-14A CV-14B CVM-14B BT40 direct driven rpm (5.5/7.5kW) X X X X X X BT40 direct driven rpm (7.5/11kW) BT40 direct driven rpm (11/15kW) BT40 direct driven rpm (15/18.5kW) X X BT40 direct driven 12000rpm (7.5/11kW) BT40 direct driven 12000rpm (11/15kW) BT40 direct driven 12000rpm (15/18.5kW) X X BT40 direct driven 15000rpm (7.5/11kW) BT40 direct driven 15000rpm (11/15kW) BT40 direct driven 15000rpm (15/18.5kW) X X BT40 belt type rpm (5.5/7.5kW) X X X X X X X BT40 belt type rpm (7.5/11kW) X X X X BT40 belt type rpm (11/15kW) X X X X BT40 belt type rpm (7.5/11kW) X X X X BT40 belt type rpm (11/15kW) X X X X BT40 belt type rpm (15/18.5kW) X X X X X X X BT40 gear head 6000rpm (7.5/11kW) X X X X X X X X BT50 direct driven rpm (11/15kW) X X X X X X BT50 direct driven rpm (15/18.5kW) X X X X X X (CV-14AH/CV-14BH) Tool magazine 24 tools Magazine Capacity 32 tools 40 tools Tool MAS BT-40 CAT-40 Tool Shank DIN-40 MAS BT-50 X X X X X X CAT-50 X X X X X X (CV-14AH/CV-14BH) DIN-50 X X X X X X Pull Stud MAS BT-40/P40T-1 MAS BT-50/P50T-1 X X X X X X (CV-14AH/CV-14BH) Coolant Coolant system Coolant through spindle Coolant through tool and tool holder Oil skier Chip flush coolant system Coolant gun Chip disposal system Screw type chip conveyor Lift-up chip conveyor with bucket Air blast function for workpiece(m07) air blast Oil-mist collection system Measurement system Tool length measurement Workpiece length measurement Operation Support Auto power off(m30) Automatic door High accuracy control Liner scales (axis X,Y,Z) Safety system Full enclosure Others Heat exchanger on electric cabinet Auto lubrication system oil cooler (Refrigerant R407C) Work light& Tri-status light Rigid tapping function Adjusting tools and box Leveling bolts and pads Manuals in English language X-axis change from 4 blocks to 6 blocks Z-axis change from 4 blocks to 6 blocks Z-axis riser 4th axis interface Rotary table 4th axis Air conditioner unit for electric cabinet KAFO customized calculator software function Specification/Model CV-16A CVM-16A CV-16B CVM-16B :Standard specification :Optional specification X:Inadaptable DV-9A DVM-9A DV-9A APC DV-9B DVM-9B DV-9B APC DV-9C DVM-9C DV-9C APC DV-11A DVM-11A DV-11B DVM-11B BT40 direct driven rpm (5.5/7.5kW) X X X X X X X X BT40 direct driven rpm (7.5/11kW) X X BT40 direct driven rpm (11/15kW) X X BT40 direct driven rpm (15/18.5kW) X X BT40 direct driven 12000rpm (7.5/11kW) X X BT40 direct driven 12000rpm (11/15kW) X X BT40 direct driven 12000rpm (15/18.5kW) X X BT40 direct driven 15000rpm (7.5/11kW) X X BT40 direct driven 15000rpm (11/15kW) X X BT40 direct driven 15000rpm (15/18.5kW) X X BT40 belt type rpm (5.5/7.5kW) X X X X X X X X BT40 belt type rpm (7.5/11kW) X X X X X BT40 belt type rpm (11/15kW) X X X X X BT40 belt type rpm (7.5/11kW) X X X X X BT40 belt type rpm (11/15kW) X X X X X BT40 belt type rpm (15/18.5kW) X X X X X X X BT40 gear head 6000rpm (7.5/11kW) X X X X X X BT50 direct driven rpm (11/15kW) X X X X X X (CV-16AH/CV-16BH) BT50 direct driven rpm (15/18.5kW) X X X X X X Tool magazine 24 tools Magazine Capacity 32 tools 40 tools Tool MAS BT-40 CAT-40 Tool Shank DIN-40 MAS BT-50 X X X X X X CAT-50 (CV-16AH/CV-16BH) X X X X X X DIN-50 X X X X X X Pull Stud MAS BT-40/P40T-1 MAS BT-50/P50T-1 (CV-16AH/CV-16BH) X X X X X X Coolant Coolant system Coolant through spindle Coolant through tool and tool holder Oil skier Chip flush coolant system Coolant gun Chip disposal system Screw type chip conveyor Lift-up chip conveyor with bucket Air blast function for workpiece(m07) air blast Oil-mist collection system Measurement system Tool length measurement Workpiece length measurement Operation Support Auto power off(m30) Automatic door High accuracy control Liner scales (axis X,Y,Z) Safety system Full enclosure Others Heat exchanger on electric cabinet Auto lubrication system oil cooler (Refrigerant R407C) Work light& Tri-status light Rigid tapping function Adjusting tools and box Leveling bolts and pads Manuals in English language X-axis change from 4 blocks to 6 blocks Z-axis change from 4 blocks to 6 blocks X Z-axis riser 4th axis interface Rotary table 4th axis Air conditioner unit for electric cabinet KAFO customized calculator software function DV-11C DVM-11C