Pg. 1 of 5
PFN26-SS BA25 QF1438 QFT38 CT38-15 DFP6 AW14 AW316 AHB14 AHB316 BA25 AP25 TANK 10 FOG-MAST DPN-10 DPG-10 DP-10 HBEL1238 PL10-B HBSS1212 W10 SSAXLE12 AXC12 SHW3 HB1438 STR14 SIDE VIEW Pg. 2 of 5
R14 AG100 HBBEL1414 P56 QFEL1438 QF5638 HB14P HB5638 HBSSEL1238 QFBH38 INSIDE VIEW - CONTROL PANEL Pg. 3 of 5
04/04/07 910-FOG PARTS LIST PART NO. DESCRIPTION 9AHB14 HEX HEAD 1/4 INCH SCREW 9AHB316 HEX HEAD 3/16 INCH SCREW 9AG100 1.5in DRY MODEL 20 DUAL SCALE GAUGE 9AP25 PLUG 1/4 NPTM AIR FITTING - BRASS 9AW316 3/16 INCH ALLEN WRENCH 9AW14 1/4 INCH ALLEN WRENCH 9AXC12 1/2in PUSH NUT FOR AXLE CAP 9BA25 MALE/FEMALE ADAPTER 1/4 X 1/4 9CT38-15 3/8 INCH X 15 FT COILED BLACK AND CLEAR TUBING 9DFP6 6 INCH THREADED CAP FOR 10 GALLON UNIT 9DPG-10 BULKHEAD GASKET 9DP-10 9DPN-10 9FOG-IT MAST BULKHEAD BODY 1/2 FPT BULKHEAD RETAINING NUT TELESCOPING FOGGING MAST 9HB5638 HOSE BARB FOR P56 PUMP 9HB14P 1/4in BRASS HB AIR FITTING 9HB1438 1/4in MPT X 3/8in HOSE BARB (PLASTIC) 9HBEL1238 HOSE BARB ELBOW 1/2 X 3/8 9HBBEL1414 1/4 BRASS HOSE BARB X 1/4 PIPE ELB 9HBSSEL1238 304 S.S. 1/2in MPT BY 3/8in H.B. ELBOW 9HBSS1212 STAINLESS HOSE BARB 1/2 X 1/2 9P56 5700 SANTO PUMP 9PFN26-SS PNUEMATIC FOG NOZZLE WITH STAINLESS STEEL TIP - HIGH FLOW 9PL10-12 PLASTIC PLATE FOR FI-10 UNIT 9QF5638 3/8in QF PUMP FITTING / G57 9QF1438 MALE CON. 3/8in TUBE X 1/4in MPT - POLYPROPYLENE 9QFBH38 QF 3/8 IN BULKHEAD FITTING 9QFEL1438 FIXED ELBOW 3/8in TUBE X 1/4in MPT - POLYPROPYLENE 9QFT38 UNION TEE 3/8in TUBE 9R14 FILTER REGULATOR COMBO INCLUDES AFR15 AND ABR15 9SHW3 3in LONG COATED WEIGHT 9STR14 40 MESH SUCTION LINE STRAINER 9SSAXLE12 12 9/16IN x 1/2IN STAINLESS STEEL AXLE FOR 10 GALLON UNIT 9TANK 10 10 GALLON ROTOMOLDED TANK 9W10 6 in wheel X 1.25 in TPR Celcon Brg 1/2 in Axle Pg. 4 of 5
INSTRUCTIONS 1. Remove the unit from the packaging, attach the nozzle assembly to fog mast with screw provided with allen wrench provided. Connect the black tube into the tee labeled with a black ring, attach the clear tube into the other tee on the fog nozzle assembly. 2. Fill the 10 gallon tank with the solution to be fogged. 3. Place the unit in the area where fogging is needed, adjust mast to desired height, wearing proper safety equipment plug a compressed air line into the unit and evacuate the area. 4. Unplug the unit from air when finished. RETURNS: NO MERCHANDISE MAY BE RETURNED FOR CREDIT WITHOUT DEMA S WRITTEN PERMISSION. RETURN MERCHANDISE AUTHORIZATION NUMBER REQUIRED IN ADVANCE OF RETURN. WARRANTY: DEMA products are warranted against defective material and workmanship under normal use and service for one year from the date of manufacture. This limited warranty does not apply to any products which have a normal life shorter than one year or failure and damage caused by chemicals, corrosion, improper voltage supply, physical abuse, or misapplication. Rubber and synthetic rubber parts such as o - rings, diaphragms, squeeze tubing and gaskets are considered expendable and are not covered under warranty. This warranty is extended only to the original buyer of DEMA products. If products are altered or repaired without prior approval of DEMA, this warranty will be void. Defective units or parts should be returned to the factory with transportation prepaid. If inspection shows them to be defective, they will be repaired or replaced without charge, F.O.B. factory. DEMA assumes no liability for damages. Return merchandise authorization number, to return units for repair or replacement, must be granted in advance of return. Pg. 5 of 5