TTHMNT OPRTOR S MNUL Twin agger Mfg. No. escription 1695595-00 Twin agger / 38 Mower 1696752-00 Twin agger / 38 Mower opyright riggs & Stratton Power Products Group, LL Milwaukee, WI US. ll Rights Reserved 1737390 Rev.:
Table of ontents Operator Safety... 4 General Warnings... 4 Safety ecals... 4 ssembly... 5 affle and lade Installation... 5 Install Mounting Plates and Spacers... 6 Hitch and rame ssembly... 6 Install Lower hute omponents... 7 Operation... 8 ollector Installation... 8 ttach ollector ags... 8 Operation... 9 ollector Removal... 10 Storage... 10 Warranty... 11 NOT: In these instructions, left and right are referenced from the operating position. 3
Operator Safety Read these safety rules and follow them closely. ailure to obey these rules could result in loss of control of unit, severe personal injury or death to you, or bystanders, or damage to property or equipment. The triangle in text signifies important cautions or warnings which must be followed. General Warnings Know the unit s controls and how to stop quickly. R TH OPRTOR S MNULS. Read and obey all safety decals. Only allow responsible adults, who are familiar with the instructions, to operate the unit. isengage the PTO. Shut off the engine and wait for all moving parts to stop before attaching, adjusting, or disconnecting any part of the collection system. heck the collection system to make sure it is bolted tightly to the unit. O NOT operate the unit without either the entire grass catcher or the deflector in place. Turn off the PTO to disengage the blades when not mowing. O NOT mow in reverse unless absolutely necessary. lways look down and behind before and while travelling in reverse. O NOT turn sharply when travelling alongside a building or any object. Slow down before turning. O NOT carry passengers. When collection system is removed from the mower deck, the deflector must be properly installed. ollector bags are subject to deterioration and wear during normal use. Inspect the bag periodically for tears, holes, or weak spots and replace with a new bag that meets manufacturer s durability standards. or added stability and to prevent tipping or loss of control: a. Use reduced speed on uneven ground and when turning corners. b. Reduce loads on hillsides. It is recommended that the collection system be kept only half full when negotiating any slopes. Start mowing on slopes when the collection system is empty. c. Mow up and down the face of slopes; never across the face of any slope. Never operate on slopes greater than 17.6% (10 ). Safety ecals Several safety labels are installed on the unit to remind you of important information while you are operating your unit. ll NGR, WRNING, UTION and instructional messages on your rider, attachments and mower should be carefully read and obeyed. Personal bodily injury can result when these instructions are not followed. The safety decals below are on your product. If any decals are lost or damaged, replace them at once. See your local dealer for replacements. These labels are easily applied and will act as a constant visual reminder to you, and others who may use the equipment, to follow the safety instructions necessary for safe, effective operation. ttachment ecal WRNING Thrown objects hazard Objects thrown by the mower can seriously injure or kill you. o not open the hopper while the mower blades are turning. o not operate the mower without the complete catcher in place. ecal - WRNING Thrown Objects Hazard Part Number 1732819 1732819 4
ssembly G H igure 1 WRNING: efore beginning any service work turn off the PTO, set the parking brake, turn off the ignition, and disconnect the spark plug wire(s). affle and lade Installation Note: Units with an anti-blowout baffle do not require the lean Sweep baffle. 1. Remove mower deck.see Operator s manual. 2. Install notched side of baffle (, igure 1) to discharge side of deck securing with 5/16-18 x 2 carriage bolt () and 5/16-18 locknut ().Install 5/16-18 wing nut () and locknut (G) to carriage bolt () as shown. 3. Secure center of baffle () to deck using 5/16-18 x 2 carriage bolt (), spacer () and nut ().Secure LH end of baffle to deck using 5/16-18 x 5/8 carriage bolt () and nut (). 4. Remove right hand blade (, igure 2).Use a block of wood (igure 2) to prevent blade rotation while loosening the capscrew. 5. Position cover (H, igure 1) and new blade from kit (I) as shown. 6. Reinstall the large washer, spring washer (K) and capscrew (L). Use a wooden block (igure 3) to prevent blade rotation while tightening the capscrew to 45-55 ft.lbs.(61-75 Nm). 5 igure 2 igure 3 LOOSN I J K L
ssembly Install Mounting Plates and Spacers 1. Mount the side brackets (, igure 4) to both sides of the frame using the holes shown. Secure with one 3/8-16 x 1 capscrew (), 3/8 lockwasher (), and 3/8-16 nut () per side. Hitch and rame ssembly 1. Install the bag and cover support (, igure 6) to upright support () using 3/8-16 x 1 capscrews () and 3/8-16 locknuts () as shown. igure 4 2. Install the rear spacers (, igure 5).Secure with two 1/2-13 x 2-1/2 capscrews (), washers (G), and 1/2-13 nylock nuts (H) per side. H G igure 6 2 ttach hitch and upright support assembly (, igure 7) to frame spacers () as shown. igure 5 igure 7 6
ssembly 3. ttach cover assembly (G, igure 8) to cover support (H) using hinge pivots (I). Secure cover using hinge pins (J) and hair pins (K) as shown. G I igure 8 Install Lower hute omponents 1. Secure the puck (, igure 9) to lower chute () using 5/16-18 x 3/4 capscrew () and 5/16-18 locknut (). 2. Install bracket () and deflector prop (G) to lower chute using 5/16-18 x 3/4 capscrews () and 5/16-18 locknuts (). J K H K J I Install Lower hute 1. Lift discharge deflector (, igure 10). 2. Slide the notch of bracket (G) on to deflector hinge rod (). 3. Secure the front of lower chute () to carriage bolt () using wing nut () and locknut (). Note: Locknut is intended to keep wing nut on carriage bolt if permanent installation is desired. G J K G igure 9 igure 10 7
Operation ollector Installation 1. Slide discharge tube (, igure 11) into seal ().It may be necessary to lengthen several slits in the seal to permit proper fit. 2. ttach the discharge tube to lower chute () and secure by moving wire form () down over metal puck (), see inset. igure 11 ttach ollector ags 1. Raise the cover (, igure 12). 2. ttach collector bags () using grass bag hanger () to bag hanger post (). Note: It may be necessary to fold seat forward to allow cover to stay in the raised position. igure 12 8
Operation efore Operation lear the lawn of all sticks, stones, wire and other debris which may be caught or thrown by the mower blades. heck grass condition. If wet, wait until later in the day. If grass is wet, the grass catcher is likely to become plugged. or efficient bagging, air circulation under the mower deck, through the chute and into the bag is very important. or this reason, OR YOU GIN MOWING you should make certain the underside of the mower and the underside of the catcher lid are free from grass and debris. Make sure that there is a snug fit between mower deck, blower housing, tubes, and grass catcher cover. Mowing with the atcher lways operate with throttle at full speed when mowing. Grass should be cut often, and not too short. If grass is too long or lush it may be necessary to keep ground speed to a minimum or to cut only half the width of the mower to prevent clogging. If grass is long, operate with mower in high cutting position for first pass, cutting again in a lower position on a second pass. o not open the cover with mower engaged. If a large amount of cut grass is spilling out from under deck, the tube may be plugged or the bags may be full discontinue mowing, stop the unit, disengage the PTO, shut off the engine and then empty the catcher or clear the tube. WRNING: LWYS shut off the tractor. isengage the PTO, and allow all moving parts to stop OR disconnecting or clearing tube, or emptying catcher. efore leaving the operator s position for any reason, engage the parking brake, disengage the PTO, stop the engine and remove the key. To reduce fire hazard, keep the engine, rider and mower free of grass, leaves and excess grease. o not stop or park rider over dry leaves, grass or combustible materials. fter Operation Remove any debris from the screen on the underside of the lid. The blower housing and tube should be removed for cleaning. Inspect the grass bags for wear or damage. Make sure that there is a snug fit between mower deck, blower housing, tubes, and grass catcher cover. UTION: o not leave grass in bagger containers. mpty containers after each use and before storing. ailure to do so may result in spontaneous combustion which could develop into a fire. UTION: efore you begin operating the unit be certain you have read all of the safety and operational information of this instruction sheet, as well as the Operator s Manual for the tractor and any other attachments. NOT: Never operate on slopes greater than 17.6% (10 ). 9
Operation ollector Removal UTION: Operation Without agger or operation without bagger, the mower deflector MUST be properly installed in the down position and retained by the spring latch. 1. Lift up cover ( igure 13), then remove and empty bags (). 2. isconnect the discharge tube () from lower chute () by moving wire form () up and out from metal puck (G). Remove discharge tube from seal (H). 3. Remove hitch and frame assembly () from rear of tractor. 4. Lift discharge deflector (I). Loosen wing nut (J). 5. Slide lower chute () off carriage bolt (K) and deflector hinge rod (L). J K L G I H Storage igure 13 Storing The Grass atcher lean the grass catcher thoroughly using a mild detergent (other products may damage the tube). Remove any debris from the screen on the underside of the lid. If paint has been scratched on metal parts, touch up with paint, or apply a thin film of oil to prevent corrosion. Store in a dry area. ry thoroughly before storing for a long period of time. lways store away from moisture. 10
Warranty RIGGS & STRTTON PROUTS WRRNTY POLIY January 2014 LIMIT WRRNTY riggs & Stratton warrants that, during the warranty period specified below, it will repair or replace, free of charge, any part that is defective in material or workmanship or both. Transportation charges on product submitted for repair or replacement under this warranty must be borne by purchaser. This warranty is effective for and is subject to the time periods and conditions stated below. or warranty service, find the nearest uthorized Service ealer in our dealer locator map at [insert website address]. The purchaser must contact the uthorized Service ealer, and then make the product available to the uthorized Service ealer for inspection and testing. There is no other express warranty. Implied warranties, including those of merchantability and fitness for a particular purpose, are limited to the warranty period listed below, or to the extent permitted by law. Liability for incidental or consequential damages are excluded to the extent exclusion is permitted by law. Some states or countries do not allow limitations on how long an implied warranty lasts, and some states or countries do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation and exclusion may not apply to you. This warranty gives you specific legal rights and you may also have other rights which vary from state to state or country to country.** WRRNTY PRIO Item onsumer Use ommercial Use ccessory/ttachment 12 months None ** In ustralia - Our goods come with guarantees that cannot be excluded under the ustralian onsumer Law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. or warranty service, find the nearest uthorized Service ealer in our dealer locator map at RIGGSandSTRTTON.OM, or by calling 1300 274 447, or by emailing or writing to salesenquires@briggsandstratton.com.au, riggs & Stratton ustralia Pty Ltd, 1 Moorebank venue, NSW, ustralia, 2170. The warranty period begins on the date of purchase by the first retail or commercial consumer. onsumer use means personal residential household use by a retail consumer. ommercial use means all other uses, including use for commercial, income producing or rental purposes. Once a product has experienced commercial use, it shall thereafter be considered as a commercial use product for purposes of this warranty. To ensure prompt and complete warranty coverage, register your product at the website shown above or at www.onlineproductregistration.com, or mail the completed registration card (if provided), or call 1-800-743-4115 (in US). Save your proof of purchase receipt. If you do not provide proof of the initial purchase date at the time warranty service is requested, the manufacturing date of the product will be used to determine the warranty period. Product registration is not required to obtain warranty service on riggs & Stratton products. OUT YOUR WRRNTY Warranty service is available only through [insert brand] uthorized Service ealers. Most warranty repairs are handled routinely, but sometimes requests for warranty service may not be appropriate. This warranty covers only defects in materials or workmanship. It does not cover damage caused by improper use or abuse, improper maintenance or repair, or normal wear and tear. Improper Use and buse - The proper, intended use of this product is described in the Operator s Manual. Using the product in a way not described in the Operator s Manual or using the product after it has been damaged will not be covered under this warranty. Warranty coverage will also not be provided if the serial number on the product has been removed or the product has been altered or modified in any way, or if the product has evidence of abuse such as impact damage or water/chemical corrosion damage. Improper Maintenance or Repair - This product must be maintained according to the procedures and schedules provided in the Operator s Manual, and serviced or repaired using genuine riggs & Stratton parts or equivalent. amage caused by lack of maintenance or use of non-original parts is not covered by warranty. Normal Wear and Tear - Like most mechanical devices, your unit is subject to wear even when properly maintained. This warranty does not cover repairs when normal use has exhausted the life of a part or the equipment. Maintenance and wear items such as filters, belts, cutting blades, and brake pads (except engine brake pads) are not covered by warranty due to wear characteristics alone, unless the cause is due to defects in material or workmanship. Other xclusions - This warranty excludes damage due to accident, abuse, modifications, alterations, improper servicing, freezing or chemical deterioration. ttachments or accessories that were not originally packaged with the product are also excluded. This warranty does not include used, reconditioned, second-hand, or demonstration equipment or engines. This warranty also excludes failures due to acts of God and other force majeure events beyond the manufacturer s control. 11