Sulzer Chemtech Statomix TM The Line of High Quality Motionless Mixers MOVING AHEAD 0607 4451
Contents ME and MS Series Bell Mouth Mixers 4 SH Series Shrouds 5 SM Series Stainless Steel Mixers 6 AE Series Stainless Steel Mixers with Removable Elements 7 KS Series Steel /Fibreglass Mixers FM Series Flexible Plastic Mixers 9 MR Series Rotary Mixers Luer Lock Adapters 11 3
ME &MSSeries Bell Mouth Mixers Statomix TM ME &MSSeries plastic disposable mixers, when used with meter-mix and dispense equipment, provide a low cost solution for 2-component mixing. The mixer element is moulded in polyacetal to allow for ahigh pressure differential associated with meter-mix equipment. 0607 4452 0607 4452-1 Statomix TM ME &MSSeries mixers are provided with stepped ends which can be cut off to increase the outlet diameter. Note: The only functional difference between ME series and MS series mixers is the inner diameter of the bell mouth housing: ME =15.9 mm and MS =16.7 mm (see illustration below) Material Housing Material Elements Max. allowable pressure Polypropylene (PP) Polyacetal (POM) According to table below I.D. O.D. Bell Mouth Mixers Diameter ME Style: 15.9 mm MS Style. 16.7 mm 0607 4452-2 Important: For health and safety reasons, Statomix SH Series safety shrouds must be used at all times 5 6.4 13 9. 9..5.5 11. 14 17 Outlet Dia. d(mm) 1.5 1. 1. 2.4 4.5 2.4 3 4 Max. Operating Pressure at40 C(bar) 33 27 22 17 149 1 16 235 334 37 223 29 214 276 355 293 37 No. of Elements 32 32 4 56 32 1 32 32 Part Number ME or MS 05- ME or MS 05-32 ME or MS 06- ME or MS 06-32 ME or MS 06-4 MS 06-56 ME or MS 0- ME or MS 0-32 MS -1 ME or MS - ME or MS -32 ME or MS 13- ME or MS 13-32 Bell Mouth Combo Mixers / 13/ 14/ 17/14 2.4 7.2 22 17 409 499 +32 +32 ME or MS -032 ME or MS 13-32 4
SH Series Shrouds High quality safety shrouds are available for use with Statomix type ME &MSmixers. High pressures, which are associated with dispensing equipment, require the use of shrouds. Important: For health and safety reasons, Statomix shrouds must be used at all times. 0607 4453 Material Housing: Aluminium alloy; Fitting: Aluminium alloy Finish Anodized 1 Standard Fitting 7/ - 9 UNC Thread 2 Optional Fitting 7/ -14UNC Thread Nut across Flats 27.0 mm (1 1/16 ) Tolerances +/- 1mm ID O.D. AD 0607 4453-1 L Shrouds for ME &MS Mixers For Mixer Type ME or MS 05- ME or MS 05-32 ME or MS 06- ME or MS 06-32 ME or MS 06-4 ME or MS 06-56 ME or MS 0- ME or MS 0-32 ME or MS - ME or MS -32 ME or MS 13- ME or MS 13-32.2.2.7.2 14.2 17.2 11.5 14.0 15.0 16.0 19.0 23.0 146.0 15.0 179.5 22.5 329.0 33.5 215.0 279.0 265.5 341.5.5 5.5 Part Number 1 SH 05--09 SH 05-32-09 SH 06--09 SH 06-32-09 SH 06-4-09 SH 06-56-09 SH 0--09 SH 0-32-09 SH --09 SH -32-09 SH 13--09 SH 13-32-09 Part Number 2 SH 05--14 SH 05-32-14 SH 06--14 SH 06-32-14 SH 06-4-14 SH 06-56-14 SH 0--14 SH 0-32-14 SH --14 SH -32-14 SH 13--14 SH 13-32-13 Shrouds for Combo Mixers ME or MS -032 ME or MS 13-32 14.2/.2 17.2/14.2 19/16 23/19 401.0 503.0 SH -44-09 SH 13-44-09 SH -44-14 SH 13-44-14 5
SM Series Stainless Steel Mixers Statomix TM SM Series stainless steel tube mixers are suited for mixing two-component reactive resin systems. These durable stainless steel mixers consist of alternating left and right hand helical elements, which are nickel brazed within the entire length of the tubular mixer housing. The mixer has to be cleaned immediately after use and it is recommended to briefly flush it with the main component only and then with a mixture of solvent/air.if partial or complete hardening of the components occurs, it can be burned out at 500 to 600 C. 0607 4454 Material Housing: Stainless steel 1.4571; Elements: Stainless steel 1.4404 or 1.4435 Number of Elements or Retention of Elements End Connectors Brazed with nickel base alloy over entire length of element assembly Plain ends Design Pressure Max. allowable operating pressure (see table below) according to DIN 13, scope of application 1, permanent elongation limit 1% at C, safety factor 1.7 Tolerances O.D. and wall: According to DIN 2391, page 1; +/- 1 mm I.D. O.D. 0607 4454-1 L Stainless Steel Mixers with Fixed Elements 3 4 5 6 11 15 25 6 6 14 14 16 25 Max. Operating Pressure (bar) 700 467 525 350 400 0 350 350 233 1 154 14 14 15 2 221 275 294 6 45 416 51 440 54 550 65 7 9 922 1150 No. of Elements Part Number SM 03-06- SM 03-06- SM 04-06- SM 04-06- SM 05-0- SM 05-0- SM 06-0- SM 06-0- SM 0-- SM 0-- SM -14- SM -14- SM 11-14- SM 11-14- SM -16- SM -16- SM 15-- SM 15-- SM -25- SM -25- SM 25-- SM 25-- 6
AE Series Stainless Mixers with Removable Elements Statomix TM AE Series stainless steel tube mixers are fitted with removable elements and are designed for use with 2-component reactive silicone elastomers, silicone foams and resin systems with fillers where cleaning is not possible by burning out the mixer content. A retaining ring, positioned at the outlet end of the housing, supports the elements by means of the downstream part of the compression fitting. This type of mixer should be cleaned immediately after use and it is recommended to flush it with the main component only and then with a mixture of solvent/air. Should further cleaning still be necessary, the elements may be removed and soaked in solvent. 0607 4455 Material Housing: Stainless steel 1.4571; Elements: Stainless steel 1.4404 or 1.4435 Number of Elements or 1 Retention of Elements End Connectors Retention ring on downstream end of housing ERMETO fitting Design Pressure Max. allowable operating pressure (see table below) according to DIN 13, scope of application 1, permanent elongation limit 1% at C, safety factor 1.7 Tolerances O.D. and wall: According to DIN 2391, page 1; +/- 1 mm Flow T O.D. I.D. C 0607 4455-1 L Retaining ring to be retained by downstream fitting Stainless Steel Mixers with Removable Elements 15 25 14 16 25 Retaining Ring C(mm) 6 16 Max. Operating Pressure (bar) 467 400 350 350 233 154 226 192 22 2 33 290 425 35 556 46 714 No. of Elements 1 1 1 1 1 1 Part Number AE 0-- AE 0--1 AE -14- AE -14-1 AE -16- AE -16-1 AE 15-- AE 15--1 AE -25- AE -25-1 AE 25-- AE 25--1 Thread T Mx1.5 M22x1.5 Mx1.5 Mx2 Mx2 M42x2 7
KS Series Steel /Fibreglass Mixers Statomix TM KS Series steel/fibreglass mixers weredeveloped as a low-cost alternative for mixing 2-component reactive resins. The mixing elements are made of ahigh-grade, solvent resistant plastic. A transverse rod supports the elements at the outlet end of the zinc-plated steel housing. Steel/fibreglass mixers are not suitable for the mixing of extremely high viscosity materials at temperatures above 0 C. 0607 4456 Material Number of Elements or Retention of Elements End Connectors Housing: Zinc-plated carbon steel St 35 (stainl. steel available on request) Elements: Fibreglass reinforced engineering plastic (PET) Nickel brazed retention pin across the last element at downstream end of housing Plain ends Max. Operating Temperature 0 ºC Design Pressure Max. allowable operating pressure (see table below) according to DIN 13, scope of application 1, permanent elongation limit 1% at C, safety factor 1.7 Tolerances O.D. and wall: According to DIN 2391, page 1; +/- 1 mm Flow I.D. O.D. 0607 4456-1 L Retention pin Steel /Fibreglass Mixers 11 13 16 14 16 25 Max. Operating Pressure (bar) 226 2 2 226 226 3 0 277 411 327 46 402 596 501 744 No. of Elements Part Number KS 0-- KS 0-- KS 11-14- KS 11-14- KS 13-16- KS 13-16- KS 16-- KS 16-- KS -25- KS -25-
FM Series Flexible Plastic Mixers The Statomix FM Series mixers were developed for 2-component coatings and other very low viscosity materials. The mixer housing is flexible and made from high-strength Polyamide with low moisture absorption and is suited for a flexible installation. The Statomix FM Series mixers are not suited for high pressure or for mixing of high viscosity materials. The mixer should be cleaned immediately after use with amixture of solvent/air. 0607 4457 Material Number of Elements or Retention of Elements End Connectors Max. Operating Temperature Tolerances Housing: Polyamid (PA free from plasticizer) Elements: Polypropylene (PP) By means of a crimp on both ends of housing Plain ends According to the table below. For higher pressures and temperatures above 40 C it is necessary to use a protective covering +/- 1 mm C Flow C I.D. O.D. 0607 4457-1 L Flexible Plastic Mixers 6.4.0 9 Notch Recess C(mm) 13 Max. Operating Pressureat40ºC (bar) 14 9 1 263 0 334 No. of Elements Part Nummer FM 06-09- FM 06-09- FM 0-- FM 0-- 9
MR Series Rotary Mixers Statomix TM MR Series plastic disposable rotary mixers are suited for mixing low viscosity 2-component reactive resin systems. The first mixing element is provided with ahole for attachment to the dispensing head driveshaft. MR Series mixers are provided with stepped ends which can be cut to increase the outlet diameter. 0607 445 Material Number of Elements Mixer Connection Max. allowable Pressure Housing: Polypropylene (PP) Elements: Green Polyacetal (POM) MS style bell mouth (dia. 16.7 mm) for retaining nut or STATOMIX safety shroud with 7/ - 9 UNC Thread According to table below. For higher pressures and temperatures above 40 C, a shroud must be used. Protective Cap 0607 445-2 Rotary Mixers 6.4.0.0 13.0.0.0 14.0 17.0 Outlet Dia. d(mm) 1. 2.4 3.0 4.0 Max. Operating Pressureat40ºC (bar) 27 22 17 111.5 1.0 155.0 197.0 No. of Elements Part Nummer MR 06- MR 0- MR - MR 13-
Luer Lock Adapters Luer Lock Adapters Low-cost Luer Lock Adapters are designed for a wide range of Statomix motionless mixers. These adapters screw to the tip of the mixer and facilitate the attachment of dispensing needles for precise application of fine beads or dots and to reach within small spaces. Three colour-coded sizes of Luer Lock Needle Adapters are designed to cover the range from I.D. 5toI.D. mixers and fit all standard Luer Lock type needles. 0607 4459 0607 4459-2 ( mm across flats) Luer Lock Adapter Mixer 5 6+ Colour withe grey black Part Nummer LA 05-00 LA 06-0 LA -00 11
Sulzer Mixpac Ltd. Grundstrasse 6343 Rotkreuz Switzerland Phone +41 41 799 04 00 Telefax +41 41 799 04 04 mixpac@sulzer.com www.sulzerchemtech.com Sulzer Mixpac USA Inc., Willow Street Salem, NH 079 USA Phone +1 603 93 2727 Telefax +1 603 93 3737 mixpacusa@sulzer.com www.sulzerchemtech.com Sulzer Metix (UK) Ltd Henson Way Kettering, Northants NN16 PX United Kingdom Phone +44 15 3990 Telefax +44 15 395 metix@sulzer.com www.sulzerchemtech.com Sulzer Chemtech Ltd, a member of the Sulzer Corporation, with headquarters in Winterthur, Switzerland, is active in the field of process engineering and employs some 2500 persons worldwide. Sulzer Chemtech is represented in all important industrial countries and sets standards in the field of mass transfer and static mixing with its advanced and economical solutions. The activity program comprises: Process components such as trays, structured and random packings, internals for separation columns and reaction technology Engineering services for separation and reaction technology such as optimizing energy consumption, plant optimization studies, preengineering for governmental approval, basic engineering Separation and purification of organic chemicals by means of crystallization and membranes Mixing and reaction technology with static mixers Mixing and Cartridges Technology Tower field services 21.06.06.40 -III.0 -Printed in Switzerland