ma-porter ode Description Starting aid 1) Without start capacitor With start capacitor 5 Size 5 DN 6 DN 65 01 Impeller size SE Motor version SE Single-phase motor with float switch NE Single-phase motor without float switch ND Three-phase asynchronous motor without float switch Main applications Drainage systems Water extraction Drainage Fluids handled Grey water Waste water containing long fibres and solid substances Gas-containing fluids Operating data Operating properties haracteristic ma-porter ma-porter S Flow rate Q 40 m 3 /h (11 l/s) 17 m 3 /h (4.7 l/s) Head H 16 m 21 m Fluid temperature t max. +40 (+70 for short periods) Designation Example: ma-porter S 545 SE Key to the designation ode Description ma-porter Type series S Impeller 1) F impeller S S impeller Design details Design Fully floodable submersible motor pump lose-coupled design Vertical installation Single-stage Installation types Wet-installed stationary pump sets Wet-installed transportable pump sets Shaft seal Drive end Shaft seal ring Pump end 1 bi-directional mechanical seal with liquid reservoir Impeller type Drive Free-flow impeller (impeller type F) Impeller with cutter (impeller type S) Single-phase motor Hz: 230 V With integrated temperature switch Three-phase asynchronous motor Hz: 400 V DOL starting Suitable for the following fluids: fluids containing solids and stringy material as well as fluids with entrapped air or gas Enclosure: IP68 (permanently submerged) to EN 529 / IE 529 Thermal class of winding insulation: F earings Grease-lubricated bearings sealed for life Suitable for the following fluids: faeces, domestic sewage and waste water containing long fibres 1) lank
oating and preservation Primer and top coat Surface treatment: Top coat: Special coating lasted to S 2 1 / 2 to DIN EN ISO 944 Two-component high-solid epoxy resin finish (RL 02), min. layer thickness = 75 µm vailable on request (extra charge and a longer delivery period apply). Materials Overview of available materials omponent ma-porter 5 / 6 ma-porter S 545 asing JL 1030 F impeller JL 1030 JL 1040 utter - 1. (K) Shaft 1.4021 Shaft seal Drive end Shaft seal ring olts and nuts Joint rings Float switch Pump end Product benefits Mechanical seal Si / L 2 O 3 2 Nitrile Polypropylene Mechanical seal Si / Si Easy and fast installation/removal with polarised, absolutely watertight cable and KS plug connection ensuring correct installation Motor absolutely watertight, also in the event of damage to the cable sheath and core insulation, with individually stripped, tinned and resin-sealed conductors High operating reliability due to dry, pressure-tight and encapsulated squirrel-cage motor, thermal class F Three-phase motor: protected against overheating even under tough operating conditions due to generously sized motor. motor: protected against overheating by thermal switches in the windings Long service life with shaft made of corrosion-resistant stainless steel Increased reliability due to bi-directional mechanical seal Ease of service with wetted bolts made of stainless steel, which are easy to undo even after years of operation Trouble-free operation: clogging by coarse particles is prevented by large free passage (free-flow impeller) or by cutter with high mechanical resistance for waste water Stationary pump sets easy to install and remove with automatic, bolt-free connection; leakage prevented by elastic sealing elements ertifications Label Valid in: omment Europe Suitable for plants to Standard EN 0-1 Europe MW (test report) Nos.: 04266-01 to 05
Overview of range Standard variants Size F impeller S impeller ma-porter 5 / 6 ma-porter S 545 Motor version SE NE ND SE NE ND Number of motor poles 2-pole Explosion protection Motor versions SE, NE, ND Not explosion-proof Motor With start capacitor - - - - Starting method DOL 2) Voltage 230 V 1~ 230 V 1~ 400 V 3~ 230 V 1~ 230 V 1~ 400 V 3~ ooling ooled by surrounding fluid Mode of operation S1 submerged (max. 10 m) Level measurement: with float switch - - - - Power cable Type Rubber-sheathed cable H07RN8-F 3x1² H07RN8-F 4x1² Length 10 m 3) able entry bsolutely watertight Sealing elements Shaft seal Drive end: shaft seal ring Pump end: mechanical seal Elastomer seals NR Monitoring equipment Winding temperature Thermal motor protection - Thermal motor protection - oating Environmentally friendly KS top coat (two-component epoxy paint), colour RL 02, film thickness = 75 µm Installation Stationary, with guide hoop Installation depths 1.5 m/1.8 m/2.1 m Stationary, with single guide rail Installation depth 4.5 m Stationary, with twin guide rail Installation depth 4.5 m Stationary, with guide wire Installation depth 4.5 m Transportable Installation depth 4.5 m Maximum temperature of fluid handled Motor versions SE, NE, ND 40 2) Maximum switching frequency: starts per hour 3) Optional: m
Technical data ma-porter 5, F impeller Hz - 1 ~ 230 V, 10 m power cable 0 SE 45 1,00 0,55 5,00 18,2 3 x 1,0 39017187 23 1 SE 110 45 1,25 0,75 6,00 18,2 3 x 1,0 39017 23 2 SE 0 43 1, 1,10 8, 18,2 3 x 1,0 39017101 23 3 SE 130 41 1, 1,10 8, 18,2 3 x 1,0 39017102 23 0 NE 45 1,00 0,55 5,00 18,2 3 x 1,0 39017195 22 1 NE 110 45 1,25 0,75 6,00 18,2 3 x 1,0 39017188 23 2 NE 0 43 1, 1,10 8, 18,2 3 x 1,0 39017189 23 3 NE 130 41 1, 1,10 8, 18,2 3 x 1,0 39017190 23 Hz - 1~ 230 V, m power cable 0 NE 45 1,00 0,55 5,00 18,2 3 x 1,0 39018542 23.2 1 NE 110 45 1,25 0,75 6,00 18,2 3 x 1,0 39018543 23.2 2 NE 0 43 1, 1,10 8, 18,2 3 x 1,0 39018544 23.2 3 NE 130 41 1, 1,10 8, 18,2 3 x 1,0 39018545 23.2 Hz - 3 ~ 400 V, 10 m power cable 0 ND 45 0,90 0,55 2,30 18,3 4 x 1,0 39017191 22 1 ND 110 45 1,10 0,75 2, 18,3 4 x 1,0 39017103 23 2 ND 0 43 1, 1,10 3,00 18,3 4 x 1,0 39017104 23 3 ND 130 41 2,05 1, 3, 18,3 4 x 1,0 39017105 23 Hz - 3 ~ 400 V, m power cable 0 ND 45 0,90 0,55 2,30 18,3 4 x 1,0 39018538 23.4 1 ND 110 45 1,10 0,75 2, 18,3 4 x 1,0 39018539 23.4 2 ND 0 43 1, 1,10 3,00 18,3 4 x 1,0 39018540 23.4 3 ND 130 41 2,05 1, 3, 18,3 4 x 1,0 39018541 23.4 ma-porter 6, F impeller Hz - 1 ~ 230 V, 10 m power cable 1 SE 110 1,25 0,75 6,00 18,2 3 x 1,0 39017106 26 2 SE 0 58 1, 1,10 8, 18,2 3 x 1,0 39017107 26 3 SE 130 56 1, 1,10 8, 18,2 3 x 1,0 39017108 26 1 NE 110 1,25 0,75 6,00 18,2 3 x 1,0 39017192 26 2 NE 0 58 1, 1,10 8, 18,2 3 x 1,0 39017193 26 3 NE 130 56 1, 1,10 8, 18,2 3 x 1,0 39017194 26 Hz - 1 ~ 230 V, m power cable 1 NE 110 1,25 0,75 6, 18,2 3 x 1,0 39018549 26.2 2 NE 0 58 1, 1,10 8, 18,2 3 x 1,0 39018628 26.2 3 NE 130 56 1, 1,10 8, 18,2 3 x 1,0 39018629 26.2
Hz - 3 ~ 400 V, 10 m power cable 1 ND 110 1,10 0,75 2, 18,3 4 x 1,0 39017109 25 2 ND 0 58 1, 1,10 3,00 18,3 4 x 1,0 39017110 25 3 ND 130 56 2,05 1, 3, 18,3 4 x 1,0 39017111 25 Hz - 3 ~ 400 V, m power cable 1 ND 110 1,10 0,75 2, 18,3 4 x 1,0 39018546 26.4 2 ND 0 58 1, 1,10 3,00 18,3 4 x 1,0 39018547 26.4 3 ND 130 56 2,05 1, 3, 18,3 4 x 1,0 39018548 26.4 ma-porter S 545, S impeller Hz - 1 ~ 230 V, 10 m power cable S 545 SE 145 7 1, 1,10 8, 18,2 4 x 1,0 39018468 26.5 S 545 NE 145 7 1, 1,10 8, 18,2 4 x 1,0 39018469 26.5 Hz - 3 ~ 400 V, 10 m power cable S 545 ND 145 7 2,05 1, 3, 18,3 4 x 1,0 39017859 25
haracteristic curves ma-porter 5 ; n = 2900 rpm; F impeller haracteristic curves to ISO 9906 lass 2 / 3, below 10 kw to 4.4.2. The curves refer to the effective motor speed. 0 40 0 Q [US.gpm] 0 40 Q [IM.gpm] 16 14 40 10 30 8 H [ft] 6 H [m] 4 3 2 10 1 2 0 0 5 Q [m³/h] 10 25 30 0 2 Q [l/s] 4 6 8 K-M-0-5xx/0 Free passage: 0/1 = 45 mm, 2 = 43 mm, 3 = 41 mm
Dimensions ma-porter 5, F impeller, transportable wet-installed model 8 163 Ø63 (2) 5 393 (1) R=1 R7 328 52 55 40.5 110 135 98 DN-PN6 (1) Lowest switch-off point (2) Hose inner diameter: 63 mm ma-porter 5, F impeller, stationary wet-installed model with guide wire/guide hoop, duckfoot bend DN / 5 85 ISO 7005 PN 16 DN PN 16 SME 2 0 130 (3) 79 138 338 (1) D 8 148 36 DN PN16 105 0 (a) 00-10-10 (b) (2) D 98 400-5 185 0 270 436 5 (1) Lowest switch-off point (a) Minimum (2) Guide hoop (b) Maximum (3) Flange of duckfoot bend
ma-porter 5, F impeller, stationary wet-installed model with guide wire/guide hoop, straight pump foot G 2" 5 85 79 (2) 400 D 79 98 338 (1) 8 148 75 DN G 2 (a) 00-10-10 (b) D - 270 138 36 10 105 110 25 114 0 (1) Lowest switch-off point (a) Minimum (2) Guide hoop (b) Maximum ma-porter 5, F impeller, stationary wet-installed model with single guide rail, duckfoot bend DN / 76 85 ISO 7005 PN 16 DN PN 16 SME 2 0 Ø33,5 x2 130 (2) 400 8 1 113 270 DN PN16 138 98 (1) 338 36 436 5 105 0-5 185 0 (1) Lowest switch-off point (2) Flange of duckfoot bend
ma-porter 5, F impeller, stationary wet-installed model with single guide rail, straight pump foot G 2" 5 76 85 Ø33,7 x 2 400 8 1 63 98 270 (1) 338 DN G 2-138 36 105 10 110 25 114 0 (1) Lowest switch-off point ma-porter 5, F impeller, stationary wet-installed model with twin guide rails, duckfoot bend DN / E 55 70-5 E Ø 33,7 x 2 D 352 431 76 85 300 (a) 198 98 D 8 4 (a) Ø4 (a) 110 25 185 0 0 (1) 342 73 113 105 DN 0 Ø5 DN PN10-PN16 Ø0,5 SME 1 2 ISO 7005 PN10-PN16 DIN 21 PN10-PN16 SME 1 2 18 DN 535 5 130 (2) 0 (1) Lowest switch-off point (a) Minimum (2) Flange of duckfoot bend
Sump ma-porter 5 /6, F impeller / ma-porter S 545, S impeller (1) Minimum (2) ON (3) OFF Size D ma-porter 5 0 x 0 1 190 4 ma-porter 6 0 x 0 170 190 4 ma-porter S 545 0 x 0 1 190 4 (2) D (1) (3) x (1) Information on installation Suggested electrical installation layouts ma-porter is available in non-explosionproof design. ma-porter 5 / 6 E E51 E52 E53 E4 E10, E11 E13, E14 E16, E17 E18, E19 E E Suggested installation layout No. 1 Suggested installation layout No. 2
Information on installation Suggested electrical installation layouts ma-porter is available in non-explosionproof design. ma-porter 5 / 6 E E51 E52 E53 E4 E10, E11 E13, E14 E16, E17 E18, E19 E E Suggested installation layout No. 1 Suggested installation layout No. 2