INSTLLTION, OPERTION & MINTENNCE INSTRUCTIONS Kleppe Lane Sparks, NV 89-667 (77) 9-72 Fax (77) 9-72 E-mail: haws@hawsco.com website: www.hawsco.com Model 00/00HPS Drinking Fountain No. 20760(9) NOTE TO INSTLLER: Please leave this information with the Maintenance Department. LIMITED WRRNTY HWS warrants that this specific product is guaranteed against defective material or poor workmanship for a period of one year from date of shipment. HWS liability under this warranty shall be discharged by furnishing without charge F.O.B. HWS Factory any goods, or part thereof, which shall appear to the Company upon inspection to be of defective material or not of first class workmanship, provided that claim is made in writing to Haws within a reasonable period after receipt of the product. Where claims for defects are made, the defective part or parts shall be delivered to the Company, prepaid, for inspection. HWS will not be liable for the cost of repairs, alterations or replacements, or for any expense connected therewith made by the owner or his agents, except upon written authority from HWS, Sparks, Nevada. HWS will not be liable for any damages caused by defective materials or poor workmanship, except for replacements, as provided above. Buyer agrees that HWS shall not be liable for general, special, or consequential damages claimed to arise under the contract of sale. The drinking fountain manufactured by HWS is warranted to function if installation and maintenance instructions provided are adhered to. The units also must be used for the purpose for which they were intended. NO OTHER WRRNTIES EXPRESSED OR IMPLIED RE UTHORIZED, PROVIDED OR GIVEN BY HWS. SHOULD YOU EXPERIENCE DIFFICULTY WITH THE INSTLLTION OF THIS MODEL PLESE CLL: TECHNICL SUPPORT: -800-766-62 FOR CUSTOMER SERVICE: -888-60-297 02/8 Model 00/00HPS Page of
RECOMMENDED TOOLS: Hack saw, pipe joint sealant, screwdriver, level, 2" adjustable wrench, 0" pipe wrench, /2 and /2 hex key wrench, 9/6, /2", 7/6 socket wrench or open end wrench. LOCTION OF UNIT: The Model 00/00HPS Drinking Fountain is a wheelchair accessible drinking water facility. The height dimensions shown, meet current D requirements. When installing this unit, local, state or federal codes should be adhered to. If height other than shown is required, then dimensions must be adjusted accordingly. SUPPLY LINE: The minimum recommended line size is /2 IPS with 0-90 PSI (2-6 TM) flowing pressure. Where sediment or mineral content is a problem, an inlet filter is recommended. PLUMBING CONNECTIONS: Inlet is /8 O.D. push-in type fitting. Waste outlet is -/ O.D. tube. MINTENNCE: Periodically clean the strainer. Refer to 87 Series Valve Manual for more information. GENERL NOTES:. For all plastic push-in type fitting connections, only connect NSF-6 copper or plastic tubing. Stainless steel or glass tubing is not recommended. The following assembly instructions must be followed to ensure a watertight connection: a. Cut tubing square and clean. b. Mark from end of tube the length of insertion (See table below). c. Push tube into the fitting until it bottoms out. d. To remove, depress collet and pull tubing out. Tube Sizes O.D. Tolerance Insertion Depth / ±.00 /6 /8 ±.00 / /2 ±.00 7/8 CLENING INSTRUCTIONS FOR HI-POLISHED STINLESS PRODUCTS Haws recommended cleaning procedure for hi-polished stainless products is as follows: Use a mild detergent or soap and water for removing stains and fingerprints or use a clean cloth with window cleaner. 02/8 Model 00/00HPS Page 2 of
PROBLEM TROUBLESHOOTING REPIR CHECKLIST. Insufficient bubbler flow. a. Check that inlet screwdriver stop valve is in wideopen position. b. Verify minimum 0 psi flowing supply pressure. c. Clean strainer. See 87 Series Valve Manual. d. djust valve to increase flow. Use front adjust screw or see 87 Series Valve Manual. e. Clean screens (inside nozzle body). Unscrew nozzle insert and very gently activate water supply to pop out qty. screens (be careful not to lose screens). Remove any debris clogging the screen openings and place back into nozzle body. Reassemble nozzle insert. For more information about Haws products, see our website: www.hawsco.com 208 Haws Corporation ll Rights Reserved HWS and other trademarks used in these materials are the exclusive property of Haws Corporation. 02/8 Model 00/00HPS Page of
THIS DOCUMENT IS TRUE ND CORRECT T TIME OF PUBLICTION. CONTINUED PRODUCT IMPROVEMENTS MKE SPECIFICTIONS ND MESUREMENTS SUBJECT TO CHNGE WITHOUT NOTICE. ITEM DESCRIPTION 00 00HPS NOTES: 87PBF (ITEM 2) INCLUDES VRK87 CRTRIDGE SSEMBLY (ITEM ) ND PB6 FLNGED PUSH BUTTON (ITEM ). 2 6 BUBBLER HED, PCP BUTTON, PUSH, PCP, FLNGED W/ VLVE VLVE REPIR KIT BUTTON, PUSH, 87, FLNGED PNEL, BCK, F/ STIN SWIRL OR HI-POL SS PLTE, MOUNTING 70 87PBF VRK87 PB6 BP6 6700 70 87PBF VRK87 PB6 BP6HPS 6700 7 STRINER, WSTE SSEMBLY, SCP OR PCP 66 66PCP 8 9 PNEL, CCESS, SS STIN OR HI-POL PLTE, BOTTOM, F/ 000 660 PBM000 660HPS PBM000 0 DRIVER, NOZZLE,.2 HEX 00020822 00020822 DENOTES OPTIONL PRT. 2 7 6 8 70LMIN (OBSOLETE - SHOWN FOR REFERENCE ONLY.) 0 (OPTIONL) FOR REMOVL OF NOZZLE WITH TUBE 9 STYLE (TUBING CONNECTS TO ELBOW) STYLE B (TUBING CONNECTS TO INSERT SSY) FOUNTIN COULD HVE EITHER STYLE DETIL ROTTED 90 INTO VIEW PRTS BREKDOWN KLEPPE LNE SPRKS, NEVD 89 (77) 9-72 FX (77) 9-72 E-MIL: HWS@HWSCO.COM WEBSITE: WWW.HWSCO.COM ECN NO. REVISED PER BY MODEL(S) PRT NUMBER. ECN: 27 VWC DRWN DTE CHKD 00/00HPS REVISION RTM 0/9/98 VWC PPROVED DTE DRINKING FOUNTIN 9 FV 02/2/8 SCLE: : DRWING TYPE: PRTS BREKDOWN SIZE: SHEET OF WHEN ORDERING PRTS PLESE SPECIFY MODEL NUMBER. C 207 Haws Corporation - ll Rights Reserved R HWS and other trademarks used in these materials are the exclusive property of Haws Corporation. 00020760 PGE OF
THIS DOCUMENT IS TRUE ND CORRECT T TIME OF PUBLICTION. CONTINUED PRODUCT IMPROVEMENTS MKE SPECIFICTIONS ND MESUREMENTS SUBJECT TO CHNGE WITHOUT NOTICE. NOTES:. HOLD ROUGH-IN DIMENSIONS ±/8" (.2mm). 2. WHEN INSTLLING THIS UNIT, LOCL, STTE, OR FEDERL CODES SHOULD BE DHERED TO FOR INSTLLTION DIMENSIONS (LOCTIONS), WSTE ND SUPPLY REQUIREMENTS OTHER THN SHOWN. INSTLLER MUST PROVIDE TRP FOR PROPER INSTLLTION. REMOVE VLVE FROM PUSH BUTTON TO INSTLL WSTE ELBOW ONTO BOWL. FTER WSTE ELBOW IS INSTLLED, REINSTLL VLVE ND DJUST FLOW. REFER TO 87 SERIES OPERTION ND MINTENNCE MNUL FOR PUSH BUTTON ND VLVE INSTLLTION/MINTENNCE INSTRUCTIONS. ø /8" [9] WLL FCE WLL STUD MOUNTING BOLTS 6" [06] WSTE BEND ND -/" IPS TRP /" [8] " /" [76] [] 27/2" [7] SECTION - ROTTED 90 INTO VIEW BRCKET MOUNTING DETIL OF PGE DETIL C " [80] /" OD WSTE BEND (SUPPLIED) BCK PNEL (OPTIONL): 00 & 00HPS " [76] 8 /8" [7] 6700 MOUNTING PLTE (BEHIND FINISH WLL) Ø/8" SUPPLY TUBING ND SCREW DRIVER STOP X /8-6 UNC 7" [78] " [76] X ø/8" [0] 27/2" [7] 8 " [] 2 /8" [6] " [86] (TO SPOUT OUTLET) 27" [686] C WLL FCE FLOOR LINE 28 /2" [7] WSTE 28 /6" [729] SUPPLY " [27] 6" [06] 8" [7] 2" [] " [2] 6700 MOUNTING PLTE MUST BE INSTLLED BEFORE FINISH WORK. THIS PLTE IS STNDRD ITEM. 2 9/2" [8] C OPTIONL TRP CCESS PNEL MODELS 660 ND 660HPS KLEPPE LNE SPRKS, NEVD 89 (77) 9-72 FX (77) 9-72 E-MIL: HWS@HWSCO.COM WEBSITE: WWW.HWSCO.COM ECN NO. REVISED PER BY: MODEL(S) PRT NUMBER. ECN: 27 VWC DRWN: DTE: CHK'D.: 00/00HPS REVISION RTM 0/97 VWC PPROVED: DTE: DRINKING FOUNTIN 9 FV 02/2/8 SCLE: : DRWING TYPE: INSTLLTION SIZE: SHEET OF R 207 Haws Corporation - ll Rights Reserved. HWS and other trademarks used in these materials are the exclusive property of Haws Corporation. 00020760.D