Installation Instructions SERIN Deck Mount Electronic Proximity Lavatory Faucet Certified to comply with ASME A.. 0 American Standard Optional 0P00.XXX, " Deck Plate Optional 0P00.XXX, " Deck Plate 0. 0. 0. 0. 0.9 Product No.'s & Options Specifications MODEL NUMBERS 0. 0. 0. 0. 0.9 Faucet Installation Electrical Installation Start-up / Maintenance FAQ s / Troubleshooting Replacement Parts 0. 0. 0. 0. 0.9 - - - -9 0 TE TO INSTALLER: Please give this manual to the customer after installation. To learn more about American Standard Selectronic Products visit our website at: www.americanstandard-us.com or e-mail us at: CRTTEAM@americanstandard.com For Parts, Service, Warranty or other Assistance, please call () CRT-TEAM / () - (In Canada: -00--09) (In Toronto Area only: -90-0-09)
Optional 0P00.XXX, " Deck Plate Optional 0P00.XXX, " Deck Plate Certified to comply with ASME A.. 0 American Standard Product No.'s & Options Specifications Faucet Installation Electrical Installation Start-up / Maintenance FAQ s / Troubleshooting Replacement Parts TE TO INSTALLER: Please give this manual to the customer after installation. To learn more about American Standard Selectronic Products visit our website at: www.americanstandard-us.com or e-mail us at: CRTTEAM@americanstandard.com For Parts, Service, Warranty or other Assistance, please call () CRT-TEAM / () - (In Canada: -00--09) (In Toronto Area only: -90-0-09) MODEL NUMBERS 0. 0. 0. 0. 0. 0. 0. 0. 0. 0. 0. 0. 0.9 0.9 0.9 - - - -9 0 Thank you for selecting American-Standard...the benchmark of fine quality for over 00 years. To ensure that your installation proceeds smoothly--please read these instructions carefully before you begin. UNPACKING All American Standard Faucets Are Water Tested At Our Factory. Some Residual Water May Remain In The Faucet During Shipping.. Remove the fitting and loose items from the carton. The illustration below shows the fitting and all loose items after they have been removed from the carton. Some items may be packaged partially assembled to other items.. Installation Instructions. Spout Assembly. Mounting Kit. Electrical Enclosure. Supply Hose a. DC Long Life Power Pack (for.,.,.) b. DC Standard Battery (for.,.,.) c. AC Power Supply (for.,,.) d. AC Power Transfomer (.9,.9,.9). Y-Adapter. 0 ft. Extension 9. " Deck plate (optional, must be ordered separately) 0. " Deck plate (optional, must be ordered separately). Mixing Valve (optional, must be ordered separately) How to order the Serin Proximity Product. Choose Power Supply. Choose Desired Flow Rate Single Hole Sink Single Inlet and Hole Sinks Single Inlet and Hole Sinks Hot and Cold Inlets Base Product Deck Plate (optional) Mixing Valve (optional) B a s e P r o d u c t Deck Plate Mixing Valve PRODUCT No.s All 0. SERIES 0P00.XXX 0P00.XXX 0XTMV00 Spout 9 0 Installation Instructions SERIN Deck Mount Electronic Proximity Lavatory Faucet DC Long Life Power Pack 0. 0. 0. a DC Standard Battery 0. 0. 0. b AC Plug-in AC Hardwire AC Multi 0. 0. 0. 0.9 0.9 0.9 0. 0. 0. c d
Roughing-in Dimensions (mm) -/" (mm) " MOUNTING SURFACE (mm) -/" mm (-/") DIA. mm (-/") (00mm) -/" (9mm) 9-/" GENERAL DESCRIPTION: Electronic faucet with proximity operation. Vandal resistant solid brass construction single post mounting. Operates on DC (battery/power pack) or AC permanent power (plug-in/hardwire). In-line strainer for solenoid is integral. Single inlet / compression, built-in check valves, and flexible stainless steel -/" reach inlet hose for spout connection. Note: All plumbing and electrical wiring must be installed in accordance with applicable codes, regulations and standards. mm (-/") RECOMENDED ELECTRICAL BOX OR EQUIVALENT BY OTHERS " (0mm) SQ. X -/" (9mm) DEEP ELECTRICAL BOX Hubbel-RACO # OR EQUAL (BY OTHERS). HARD-WIRED AC ONLY 0 MAX. CABLE LENGTH mm (-/") mm (-/") /" COMP. 00mm (0") mm (0") RECOMMENDED TOOLS Slip Joint Pliers Adjustable Wrench Plumbers' Putty or Caulking Phillips Screwdriver Flat Blade Screwdriver Electric Drill & /" Drill Bit Tape Measure SPOUT ASSEMBLY INSTALLATION; Fig. CAUTION Turn off hot and cold water supplies before beginning Fig. 0'. Make sure O-RING () is installed into groove in ESCUTCHEON RING ().. Insert SENSOR CABLES (), SPOUT HOSE () and SPOUT SHANK () through center hole of mounting surface. Fig... Assemble RUBBER WASHER (), BRASS WASHER () and LOCKNUT (9) onto SHANK () from underside of sink or mounting surface. Hand tighten LOCKNUT (9).. Use a screwdriver to tighten SCREWS (0) on LOCKNUT (9). Work your way around LOCKNUT (9), tightening the screws slightly each time until all are snug to ensure even pressure. IMPORTANT: Do not use putty when installing faucet without escutcheon. PUTTY (If required) * SENSOR CABLES Note: " and " Deck Plates () are available for other installations, see page one for information.. When using optional " or " DECK PLATE () first thread the DECK PLATE CENTERING NUT () onto SHANK (). Thread the DECK PLATE CENTERING NUT () tight against the underside of the faucet base.. Follow steps - above for the spout installation. *(# CENTERING NUT) is only used with the installation of a " or " deck plate 0 MOUNTING SURFACE 9
MOUNT ENCLOSURE; Fig.! Important: For AC installation, make sure power supply connector is inserted into enclosure through power supply grommet before enclosure is mounted to the wall. Reference electrical installation section (pages & ).. Determine location of ENCLOSURE (). It must be located with-in the " (mm) by " (mm) shaded area shown in Figure in order for electrical connections from the spout assembly to be made. TE: ENCLOSURE SUPPLY HOSE is 0". Distance between wall supply and ENCLOSURE () must be taken into consideration.. Remove screws from ENCLOSURE COVER () and pull off COVER (). Hold the ENCLOSURE () in desired location and mark the four mounting hole locations as shown. Fig.. TE: For AC installation, make power supply connection before mounting ENCLOSURE () to wall.. It is recommended that the ENCLOSURE () be secured to a wall stud or cross brace within the wall using the SCREWS () supplied. If the ENCLOSURE () is to be installed on tile or plaster walls, the ANCHORS () and SCREWS () should be used. CONNECT SPOUT HOSE TO ENCLOSURE; Fig.. Connect SUPPLY NUT () from spout hose to nipple on top of ENCLOSURE (). Tighten with adjustable wrench to make a water tight connection. Fig.. Fig. Fig. SUPPLIES WASTE 0" (00mm) " (mm) MOUNTING HOLES " (mm) mm (0") " (mm) LAVATORY RIM OR MOUNTING SURFACE ENCLOSURE MOUNTING HOLES -/" (mm) -/" (9mm) CONNECT WATER SUPPLY TO ENCLOSURE AND WALL SUPPLY; Fig., a Fig. TE; If using the optional Mixing Valve See Sheet #M90 for installation instructions.. Insert FIBER WASHER (9) into SUPPLY NUT () on ENCLOSURE ().. Connect FLEXIBLE SUPPLY HOSE (0) to SUPPLY NUT () on ENCLOSURE (). Tighten to make a water tight connection. Use two wrenches to tighten if necessary. Fig.. Fig. a 9. Connect FLEXIBLE SUPPLY HOSE (0) directly to wall supply. Connection on FLEXIBLE SUPPLY HOSE (0) is /" compression. Use adjustable wrench to tighten connection. Do not over tighten. Fig. a. Note: FLEXIBLE SUPPLY HOSE (0) measures 0" from the bottom of the ENCLOSURE () base. If additional supply length is required, installer must purchase parts separately. COLD WATER OR TEMPERED WALL SUPPLY 0 Important: If FLEXIBLE SUPPLY HOSE (0) is too long, loop to avoid kinking.
ELECTRICAL INSTALLATION Fig. Product Page DC Long Life Power Pack (0. /.) DC Standard Battery (0. /.) AC Plug-in (0. /.) AC Hardwire (0.9 /.9) Fig. a Fig. b a AC Multi Hook-up (0. /.) INSTALL BATTERY A DC VERSIONS (LONG LIFE POWER PACK & STANDARD BATTERY); Fig. CR-P. Remove ENCLOSURE COVER (). Fig... Feed the SENSOR CABLES () through the top of ENCLOSURE (). Fig. a.. Insert BATTERY () into BATTERY HOLDER (), make sure the shape of the BATTERY () follows the shape of the BATTERY HOLDER () and terminal end is inserted first. Fig. b. Fig. c STANDARD BATTERY a LONG LIFE POWER PACK. Insert the BATTERY CONNECTOR (a) for the Standard Battery or Long Life Power Pack through side GROMMET () as shown. Fig. c.! Prior to making power connection, make sure detection zone is not obstructed. Sensor is self adjusting. Keep detection zone clear for seconds after power is connected. Fig. d a. Connect SOLEID CABLE () and BATTERY CONNECTOR (a) to SENSOR CABLES (). Place Standard Battery or Long Life Power pack into Housing. Fig. d. STANDARD BATTERY LONG LIFE POWER PACK. Replace ENCLOSURE COVER (). Tighten cover screws firmly. a
B AC VERSIONS (HARDWIRE / PLUG-IN); Fig. CAUTION Before opening ENCLOSURE disconnect AC power supply. TE: For AC installation, make power supply connection before mounting ENCLOSURE () to wall.. Remove ENCLOSURE COVER (). Fig.. Feed the EXTENSION CABLES () from the Faucet through the top of ENCLOSURE (). Fig.. FOR PLUG-IN HOOKUP ONLY a. Insert POWER CORD () through POWER SUPPLY GROMMET (9) Fig. a. a. Insert POWER CORD () through side GROMMET () as shown. Fig. a. Fig. a. Connect SENSOR CABLES () to SOLEID CABLE () and POWER CORD (). Fig. a. Fig. a a. Mount ENCLOSURE to wall. Replace ENCLOSURE COVER (). Tighten cover screws firmly.! Prior to making power connection, make sure detection zone is not obstructed. Sensor is self adjusting. Keep detection zone clear for seconds after power is connected. a. Plug AC POWER SUPPLY into wall outlet. Fig. a. 9 PLUG INTO WALL OUTLET FOR HARDWIRE HOOK-UP ONLY; b. Insert one end of the 0' EXTENSION (0a) through POWER SUPPLY GROMMET (9). Fig. b. b. Insert 0' EXTENSION (0a) through side GROMMET () as shown. Fig. b. Fig. b b. Connect 0' EXTENSION (0a) to single terminal of Y-ADAPTER (). Fig. b. b. Connect EXTENSION CABLES () from Faucet Sensor to SOLEID CABLE () and to either of the two terminals at the one end of the Y-ADAPTER (). b. Mount ENCLOSURE () to wall. Replace ENCLOSURE COVER (). Tighten cover screws firmly. Contractor to supply ELECTRICAL BOX () and power to POWER SUPPLY (). 0a 9 b. Mount POWER SUPPLY () into ELECTRICAL BOX (). Connect White and Black connections to POWER SUPPLY CONNECTIONS (). Fig. c. FROM ELECTRICAL BOX WITH POWER SUPPLY! Prior to making power connection, make sure detection zone is not obstructed. Sensor is self adjusting. Keep detection zone clear for seconds after power is connected. Fig. c " ELECTRICAL BOX OR EQUIVALENT BY OTHERS b. Connect the0' EXTENSION (0b) to the POWER SUPPLY CABLE (). Fig. c. BLACK & WHITE POWER CONNECTIONS CONNECTOR T USED IN THIS INSTALLATION 0b
Fig. Unit # Unit # Unit # 0 ft. EXTENSION CABLE 0 ft. EXTENSION CABLE AC HARDWIRE POWER SUPPLY AC POWER SUPPLY OR *MAXIMUM OF UNITS PER AC POWER SUPPLY. 0' MAXIMUM CABLE LENGTH BETWEEN UNITS. " (0mm) SQ. X -/" (9mm) DEEP ELECTRICAL BOX Hubbel-RACO # OR EQUAL (BY CONTRACTOR). C FOR AC-VERSION (MULTI HOOK-UP); Fig., a, b. Remove COVERS from all ENCLOSURES (). Fig. a SENSOR CABLES Unit # Detail. Remove SOLID BLACK PLUG GROMMET () from left side of all ENCLOSURES (), except from Unit #. Replace with GRAY GROMMET (9). (Supplied with each Faucet). 0b. Feed SENSOR CABLES () through the top of ENCLOUSURE (). Connect one SENSOR CABLE () to the SOLEID CABLE (), and the other to either of the two terminals at the one end of the Y-ADAPTER (). Connect the 0' EXTENSION (0a) to the other terminal at the same end of the Y-ADAPTER ().. Feed the other end of the 0 ft.extension (0b) through the two GRAY GROMMETS (a and b) and connect to the single terminal end of the next unit s Y-ADAPTER (). Place Y-ADAPTER () into ENCLOSURE (). AC POWER SUPPLY. Repeat Steps above for each additional Unit, for a Max. of Units on one AC POWER SUPPLY ().. Replace ENCLOSURE COVERS. Tighten cover screws firmly. Fig. b 0a a 0b b
START-UP / MAINTENANCE A HAND WASH SENSOR OPERATION; Fig. Prior to making power connection, make sure detection zone is not obstructed. Sensor is self adjusting. Keep detection zone clear for!seconds after power is connected. When the Sensor detects a user, the water immediately starts to flow. Water flow will stop. seconds after user is out of sensor range. This comfort timer allows the user to move his hands without the flow cycling on and off. As a precaution, a safety timer will turn off the water after the sensor has been blocked for seconds. Water flow will resume when the blockage is removed from the detection zone and the sensor is activated again. B HOW TO INSTALL AND CHANGE BATTERY; Fig.. Remove COVER from ENCLOSURE ().. Disconnect BATTERY HOLDER () from SENSOR CABLE ().. Remove old BATTERY from BATTERY HOLDER (). Install new BATTERY () making sure the terminal side is inserted first and shape of the battery follows the shape of the BATTERY HOLDER (). Prior to making power connection, make sure detection zone is not obstructed. Sensor is self adjusting. Keep detection zone clear for!seconds after power is connected. Fig. Fig. DETECTION ZONE: BETWEEN SPOUT AND BASE OF SINK CR-P. To change LONG LIFE POWER PACK (), unplug and replace with new Power Pack.. Reconnect BATTERY HOLDER () to SENSOR CABLE ().. Replace ENCLOSURE COVER. Tighten cover screws firmly. C HOW TO CLEAN FILTER ASSEMBLY; Fig. CAUTION Before opening ENCLOSURE disconnect AC power supply.. Remove ENCLOSURE COVER.. Close SUPPLY STOP () with mm Hex wrench. Note: Activate sensor to keep water flowing out of faucet while shutting off.. Unthread FILTER ASSEMBLY () using a /" socket.. Pull out the FILTER ASSEMBLY (), remove and clean white debris cup and filter screen.. Install the FILTER ASSEMBLY () back in its place and tighten with a /" socket. Caution: Do not over tighten.. Open SUPPLY STOP () with mm Hex wrench.. Replace ENCLOSURE COVER. Tighten cover screws firmly. Fig. mm HEX WRENCH FILTER SCREEN /" SOCKET WHITE DEBRIS CUP
D HOW TO CLEAN AND REMOVE THE AERATOR OR SPRAY; Fig.. Remove AERATOR or SPRAY HOUSING () with KEY supplied with faucet. Fig. 9. Remove AERATOR or SPRAY () from HOUSING ().. Clean the AERATOR or SPRAY SCREEN (9).. Reassemble and install into spout end. Be sure the black seal washer is in place. KEY E HOW TO CLEAN FLOW REGULATOR; Fig.. Remove SUPPLY HOSE () from top of CONTROL BOX ASSEMBLY (). Pull out FLOW REGULATOR () from CONTROL BOX ASSEMBLY ().. Rinse clean FLOW REGULATOR (). Reassemble SUPPLY HOSE () to top of CONTROL BOX ASSEMBLY () Fig. RINSE CLEAN FLOW REGULATOR () F GENERAL CLEANING; Fig.. Only use a damp, soft cloth to clean the spout and the sensor. Fig.. For tougher dirt, use a soft cloth with diluted dish washing detergent. Wipe the area using a wet cloth and dry using a soft cloth. CAUTION Do not scratch the sensor when cleaning. Avoid using any abrasives or harsh detergents or chemicals. FAQ'S Q: How will I know if the battery needs to be replaced? A: Valve will not open and sensor will continuously blink times interrupted by a pause for up to days. Q: Why has the flow rate of the faucet reduced significantly? A: The filter assembly, flow regulator or areator/spray may be clogged. Check and clean. Refer to Start-up/Mainenance, sections C, D and E. Q: Why doesn t the water flow out of faucet when I'm within the sensor detection zone? A: Battery may need replacement. Check. If sensor continuously blinks times interrupted by pause, replace battery or call () -99. Q: What is the normal operating pressure range? A: Faucet will operate with supply pressures ranging from 0-0 psi.
TROUBLESHOOTING FLOW CHARTS UNIT DOES T FUNCTION ARE EXTERNAL SUPPLY STOPS OPEN? OPEN EXTERNAL SUPPLY STOPS. IS INTERNAL SUPPLY STOP OPEN? OPEN INTERNAL SUPPLY STOP. (HEX KEY NEEDED) REPEATED DOUBLE FLASH ON SENSOR? RECONNECT BATTERY TO SENSOR. DOES SENSOR FLASH FOR SECONDS? REPLACE SOLEID CRITICALLY LOW BATTERY. INSTALL NEW BATTERY. DEAD BATTERY. INSTALL NEW BATTERY. REPEAT. CHECK FOR DAMAGE TO SENSOR WIRE INSULATION. REPLACE SENSOR. WATER IS CONTINUOUSLY RUNNING RECONNECT BATTERY TO SENSOR. DOES SENSOR FLASH FOR SECONDS? CHECK FOR DAMAGE TO SENSOR WIRE INSULATION. REPLACE SENSOR. REPLACE SOLEID LOW FLOW ISSUES ARE INTERNAL & EXTERNAL SUPPLY STOPS FULLY OPEN? FULLY OPEN INTERNAL & EXTERNAL SUPPLY STOPS BY TURNING COUNTER CLOCKWISE. LOW FLOW COULD BE CAUSED BY DEBRIS IN THE FILTER ASSEMBLY, FLOW REGULATOR OR AERATOR/SPRAY. REMOVE, CLEAN AND INSERT BACK TO ORIGINAL POSITION. HOT LINE FOR HELP For toll-free information and answers to your questions, call: () CRT-TEAM / () - Weekdays :00 a.m. to :00 p.m. EST IN MEXICO 0-00-9-00 IN CANADA -00--09 (TORONTO -90-0-09) Weekdays :00 a.m. to :00 p.m. EST Product names listed herein are trademarks of AS America, Inc. 0 To learn more about American Standard Selectronic Products visit our website at: www.americanstandard-us.com or e-mail us at: CRTTEAM@americanstandard.com 9
All 0. SERIES A999-000A SEAL M9-000A FLOW REGULATOR (. gpm) M9-000A FLOW REGULATOR (0. gpm) M9-YYY0A ESCUTCHEON KIT M99-000A MOUNTING KIT Replace the "YYY" with appropriate finish code CHROME SATIN NICKEL M99-000A SPOUT TIP SENSOR M99-YYY0A AERATOR KIT (. GPM) M9-YYY0A SPRAY KIT (0. GPM) M99-YYY0A AERATOR KIT (0. GPM) 00 9 SERIN Deck Mount Electronic Proximity Lavatory Faucet 0. 0. 0. 0. 0.9 DC LONG LIFE POWER PACK 0. 0. 0. DC STANDARD BATTERY 0. 0. 0. MODEL NUMBERS 0. 0. 0. 0. 0.9 M90-000A LONG LIFE BATTERY M90-000A BATTERY HOLDER 0. 0. 0. 0. 0.9 A9-000A SUPPLY HOSE M990-000A CONTROL BOX ASSEMBLY (POWER SUPPLY T INCLUDED AND MUST BE ORDERED SEPARATELY) AC Plug-in 0. 0. 0. M90-000A POWER SUPPLY AC Hardwire 0.9 0.9 0.9 A9-000A BATTERY V CR-P M900-000A POWER SUPPLY M90-000A 0' MULTI EXTENSION CABLE M90-000A SOLEID ASSEMBLY A900-000A FILTER ASSEMBLY A9009-000A SUPPLY STOP M90-000A Y CONNECTOR AC Multi 0. 0. 0. M90-000A 0' MULTI EXTENSION CABLE M90-000A Y CONNECTOR 0P00.XXX " DECK PLATE 0P00.XXX " DECK PLATE 0 HOT LINE FOR HELP For toll-free information and answers to your questions, call: () CRT-TEAM / () - Weekdays :00 a.m. to :00 p.m. EST IN MEXICO 0-00-9-00 IN CANADA -00--09 (TORONTO -90-0-09) Weekdays :00 a.m. to :00 p.m. EST Product names listed herein are trademarks of AS America, Inc. 0 To learn more about American Standard Selectronic Products visit our website at: www.americanstandard-us.com or e-mail us at: CRTTEAM@americanstandard.com