ISO/IEC 17025:2005 Certificate of Accreditation Certificate Number L2195 Exova, Inc. Anaheim 3883 East Eagle Drive Anaheim CA 92807 has met the requirements set forth in L-A-B s policies and procedures, all requirements of ISO/IEC 17025:2005 General Requirements for the competence of Testing and Calibration Laboratories.* The accredited lab has demonstrated technical competence to a defined Scope of Accreditation and the operation of a laboratory quality management system (refer to joint ISO-ILAC-IAF Communiqué dated 8 January 2009). Accreditation valid through: February 26, 2019 R. Douglas Leonard, Jr., President, COO Laboratory Accreditation Bureau Presented the 12 th of February 2016 *See the laboratory s Scope of Accreditation for details of accredited parameters **Laboratory Accreditation Bureau is found to be in compliance with ISO/IEC 17011:2004 and recognized by ILAC (International Laboratory Accreditation Cooperation) and NACLA (National Cooperation for Laboratory Accreditation). Form 28.1 Rev 1 7/3/13
Scope of Accreditation For Exova, Inc. Anaheim 3883 East Eagle Drive Anaheim, CA 92807 Thomas J. (Tom) Parsons 714-630-3003 x 217 In recognition of a successful assessment to ISO/IEC 17025:2005, accreditation is granted to Exova, Inc. to perform the following tests: Accreditation granted through: February 26, 2019 Testing Mechanical Chemical Resistance ASTM D543 (Practice A) Compression Constituent Content Crack Extension Deformation Under Load Environmental Flammability Flexural (Up to 600 000) lbf ASTM C364, ASTM C365, ASTM D395, ASTM D575, ASTM D695, ASTM D1621, ASTM D3410, ASTM D6484, ASTM D6641, ASTM D6742 (Section 4.2), SACMA SRM 1R, 2R, and 6R ASTM D3171 (Methods A, B, and G) ASTM D5528, EN 6033, EN 6034 ASTM D621-64e1(1988) ASTM B117, ASTM B368, ASTM D618(Method A), ASTM D750, ASTM D2126, ASTM E1237, ASTM G155 ASTM D635, ASTM D568-77(1985), ASTM D3801, ASTM D4804, FAR 25.853 ASTM C393, ASTM D747, ASTM D790, ASTM D6272, ASTM D7249, ASTM D7250 Elastomers, Foams, Prepreg, Bonded Panels Elastomers, Flow Rate ASTM D1238 Polymers 3-Point, 4-Point, and Cantilever Beam Form 28.6 Revision 5 05/23/06 Page 1 of 4
Gel Time Hardness Impact Ignition Loss Matrix Solids Content Moisture Absorption or Desorption Moisture Content Peel Resin Content Resin Flow Specimen Preparation Tear Rockwell: Durometer: (HA, HD, HM) ASTM D3532 ASTM D785, ASTM D1414, ASTM D2240, ASTM D2583, ASTM E18 ASTM D256, ASTM D746, ASTM D1822, ASTM D4812, ASTM D7136 ASTM D2584 ASTM D3529 ASTM D2126, ASTM D5229 SACMA SRM 11 ASTM D1364, ASTM D6869 ASTM D903, ASTM D1781, ASTM D1876, ASTM D3167, ASTM D3359, ASTM D5528, BMS 8-308 SACMA SRM 23, ASTM D3529, ASTM D2584, ASTM D2734, ASTM D3171, EN 2331, EN 2559, EN 2564 SACMA SRM 22 ASTM D3531 ASTM D5687, ASTM E3 ASTM D624, ASTM D1004, ASTM D1938 Resins Electrical Insulating Materials, Rubber O-Rings Rigid Cellular Polymer Matrix and Composite Adhesives Prepreg, Resins and Resins Metals and Composites Elastomers Durometer and Barcol Izod, Charpy, Brittleness Temperature, and Tensile Impact Karl-Fischer Titration Peel or Stripping Strength, Climbing Drum Peel, T-Peel, Floating Roller Peel, and Tape Adhesion Form 28.6 Revision 5 05/23/06 Page 2 of 4
Shear Tensile (UP to 600 000) lbf ASTM C273, ASTM D732, ASTM D1002, ASTM D2344, ASTM D2919, ASTM D3163, ASTM D3164, ASTM D3165, ASTM D3166, ASTM D3518, ASTM D3528, ASTM D3846, ASTM D3914, ASTM D5379, ASTM D5961, ASTM D7078, SACMA SRM 3R and 8R ASTM C297, ASTM D412, ASTM D638, ASTM D882, ASTM D897, ASTM D952, ASTM D1414(Section 8), ASTM D1623(Types B & C), ASTM D1708, ASTM D2095, ASTM D3039, ASTM D3479, ASTM D3552, ASTM D3916, ASTM D5528, ASTM D5766, ASTM D6742(Section 4.1), ASTM E8, ASTM E1237, ASTM C1275, ASTM C1359, ASTM D3759, SACMA SRM 4R Adhesives, and Adhesives, Elastomers Metals and Void Content ASTM D2734 Volatiles Content ASTM D3530 Water Absorption ASTM D570 Compression After Impact Flatwise Tension Sandwich Flexure Bearing Strength Peel Adhesion ASTM D7136, ASTM D7137, SACMA SRM 2R AMS-STD-401, ASTM C297, ASTM D7291 AMS-STD-401, ASTM C393 ASTM D953, ASTM D5961, ASTM D7248 ASTM D3330 Pressure Sensitive Tape Form 28.6 Revision 5 05/23/06 Page 3 of 4
Testing Chemical FTIR Specific Gravity Density ph Viscocity HPLC ASTM D1200 (70-370) cst Methods Used ASTM E1252 ASTM D792 ASTM D792 ASTM D1293 ASTM D1200, ASTM D1084, ASTM D2393, ASTM D2857, ASTM D6267 EN 6040, SACMA SRM 20R, QAP 34 Product Types Polymeric Materials Remarks Infrared Spectra for Qualitative Analysis Testing - Thermal Outgassing DMA DSC TGA * TMA Methods Used ASTM E595 ASTM D4065, ASTM D5023, ASTM D5024, ASTM D5026, ASTM D7028, ASTM E1640 EN 6032, SACMA SRM 18R ASTM D3417, ASTM D3418, ASTM D3895, ASTM E1269, ASTM E1952, ASTM E2160 ASTM D3850, ASTM E1131, ASTM E1582 ASTM E831, ASTM E1545, ASTM E1824, ASTM E2092 Product Types Remarks Volumetric Loss Glass Transition and Glass Transition Enthalpies of Fusion Crystallization, Glass Transition, Oxidative Induction Time, Specific Heat Capacity, and Thermal Conductivity Thermal Degradation and Compositional Analysis & Curie Point Thermal Expansion and Glass Transition Notes: 1) This laboratory offers commercial testing service. Approved by: Date: February 12, 2016 R. Douglas Leonard Chief Technical Officer Re-Issued: 2/12/16 Form 28.6 Revision 5 05/23/06 Page 4 of 4