Installation and Owner s Manual Automatic Soap Dispenser DSE101E DSE101K DSE101EH DSE101KH DSE101EP DSE101KP Thanks for your recent purchase of the TOTO Automatic Soap Dispenser. Please read the Manual thoroughly and follow all instructions. Keep the Manual in good custody for future reference.
TABLE OF CONTENTS Thank You for Choosing TOTO!... 1 Warnings... 1 Before Installation... 2 Included Parts... 2 Common Tools Needed... 2 Position of the Dispenser / Tank... 3 Installation Procedure... 4-8 Testing... 9 How to Use this Product... 9 Supplement the Soap...10... 11... 11... 12... 12... 13... 13 Rough-In Dimensions... 14... 15- THANK YOU FOR CHOOSING TOTO! The mission of TOTO is to provide the word with healthy, hygienic and more comfortable lifestyles. We design every product with the balance of form and function as a guiding principle. Congratulations on your choice. 1 WARNINGS Please read and adhere to the following notes. Failure to do so could result in personal injury and/or property damage. No person other than a service engineer should disassemble, repair or modify this dispenser, Failure to do so may result in electric shock or product malfunction. Do not use this dispenser in a humid location where condensation may collect on the surface, especially in a sauna or steam room. Do not strike or kick the dispenser or controller box, as this may damage the unit or cause a leak. Do not use this dispenser if the room temperature drops below freezing. Make sure the power cord does not come in contact with the hot water supply line. Avoid placing any objects within the detection range of the infrared sensor. Use only TOTO approved liquid soap. Make sure the electrical outlet is in a position where it will not get wet during use.
3-5/32 (80.2mm) 0G398X BEFORE INSTALLATION Read these instructions carefully to ensure proper installation. TOTO TOTO reserves the right to update product design without notice. Check to make sure you have the parts indicated on the following page. INCLUDED PARTS Spout Assembly Controller Self-tapping Screw(3X) Anchor(3X) AC Adapter(AC Type) Mounting Template Mounting Template 1-37/64 (40.1mm) 4-41/64 (117.8mm) Battery Case(DC Type) X3 Self-tapping Screw(X3) X3 Anchor(X3) Alkaline Battery (D 1.5V)(4X)(DC Type) COMMON TOOLS NEEDED Adjustable Wrench Screwdriver (Phillips) 2
POSITION OF THE DISPENSER/TANK Position of the Dispenser 1. Be sure to leave at least 4-3/4" (120mm) of space between the soap dispenser and the faucet to prevent accidental activation. 2. Leave 3-1/8"(80mm) of space maximum from the inside edge of the sink to the spout installation hole to ensure that any residual soap drips from the dispenser spout into the sink bowl. Position of the Tank 1. When installing the controller, make sure that the tube and cables can reach the tank. 2. If the tube is too long, please cut it to suitable length. Tube length: 17-3/4 (450mm) Sensor cable length: 19-3/4 (500mm) Power cord length: 59 (1500mm) (1) Space between the dispenser and the faucet to be 4-3/4 (120mm) minimum Hole for installing the dispenser [1 ~ 1-1/8 (25~28mm) in diameter] Auto Soap Dispenser (2) The distance from the soap dispenser to the edge of the sink to be 3-1/8 (80mm) maximum <4 (100mm) Tube 6 ~12 (150~300mm) <4 (100mm) Sensor cable Power cord Faucet Sink <6 (150mm) 3.Be sure there is adequate space for refilling/replacing soap tank. 3-1/2 (90mm) Cover Controller Tank 3
INSTALLATION PROCEDURE-Soap 1.Remove nut, slip washer and bottom gasket. Top gasket Remove Bottom gasket Slip washer Nut 2.Install the spout on the countertop. 3.Install bottom gasket, slip washer and nut in that order. Slip washer Nut Tube Countertop Bottom gasket Sensor cable 4.Confirm the alignment of spout and tighten nut. INSTALLATION PROCEDURE-Controller 4 Countertop Slip washer Nut Tube 1.Select the position of the controller and layout mounting template. Make sure the sensor cable and soap tube can reach the mounting template. 2.Mark the location of the mounting hloes. Drill 3 holes. Depth : 1 (25mm) Important: Mounting template to be level. Mounting template Bottom gasket Sensor cable 3-1/8 (80mm) 1-9/16 (40mm) 4-5/8 (118mm)
4.Insert self-tapping screws into the upper two holes until there is a 1/4 (6mm) gap between head of screw and wall. Use anchors if necessary. 1/4 6mm 5.Remove the tank from controller. Controller Tank 6.Hang the controller on the two screws. 7.Insert a self-tapping screw through bottom hole of controller and tighten. Self-tapping screw
8.Connect sensor cables. Sensor cable from spout Tube Sensor cable from controller INSTALLATION PROCEDURE-Tank 1.Remove pump unit from the tank. Liquid soap 2.Slowly pour liquid soap into the tank. Pump unit NOTE: Keep pump unit clean while filling soap, especially keep bottom of pump off from floor. NOTE: Fill the tank up to MAX fill line. NOTE: Use only TOTO approved liquid soap Bottom of pump MAX fill line Tank 3.Replace the pump by pushing it down firmly over the tank opening until it snaps in place. 6
4.Connect the tube to pump. (Insert the barb into the tube fully.) 5.Mount the tank to the controller. Tube Pump Tube Tank INSTALLATION PROCEDURE - Connection to Power Supply [AC Type] 1.Connect AC adapter cable to controller. 2.Plug the AC adapter into an (appropriate) outlet. NOTE : Do not use the AC adapter inserted upside. AC Adapter Cover 3.Close the cover. AC adapter cable 7
INSTALLATION PROCEDURE-Battery Box [DC] [DC Type] 1. Select position for the battery case. Make sure the power supply cable is capable of reaching the controller. 2. Mark the location of the mounting holes. 3. Drill 2 holes. Depth : 1 (25mm) 4. Insert a self-tapping screw into upper hole until there is a 1/4 (6mm) gap between head of screw and wall. Use anchors if necessary. 1/4 (6mm) 5. Hang the battery case on the screw. 6. Insert a self-tapping screw through bottom hole of case and tighten. 7. Connect power cord to controller. Power cord Self-tapping screw
TESTING After installation is complete, confirm that the dispenser is working properly using the following method. 1.Place your hands under the spout and hold them in place until soap is discharged. NOTE: Make sure there is no soap leaking from the tube and connections. HOW TO USE THIS PRODUCT Place hands under spout. automatically. Caution: Please do not obstruct the spout opening. The soap might go flying off in an unexpected direction. Caution: Please do not put liquid soap on the spout If the sensor gets dirty, it could cause malfunction. 150±15mm Sensor sensing range is 5-7/8 ±5/8(150±15mm). 5-7/8 ±5/8 Sensor window 9
REFILLING THE SOAP 1.Open the cover. Cover 2.Remove the tank from the controller. Tank 3.Remove pump unit from the tank. Pump unit 4.Slowly pour liquid soap into the tank. NOTE: Clean container before refilling. NOTE: Fill the tank up to MAX fill line. NOTE: Use only TOTO approved liquid soap. Liquid soap MAX fill line Tank 5.Replace the pump by pushing it down firmly over the tank opening until it snaps in place. 6.Mount the tank to the controller. 7.Close the cover. 8.Purge the line by holding hands under spout until soap is discharged. Dispenser can be actuated up to ten times consectutively while holding hands under the spout immediately after refilling. Tank 10 Cover Controller Pump unit Bottom of Pump
DC REPLACING THE BATTERY [DC Type] 1.Remove cover of battery case. 2.Install four (4) D size alkaline batteries. NOTE: Make sure the batteries are installed in correct orientation (polarity). 3.Relace battery case cover. 4.Tighten screws. Screws The standard life cycle time is 2 years, based on average use 2000 times/month. Battery case cover Wipe away any debris adhering to the spout or sensor. CARE AND CLEANING Battery case Batteries Wipe away debris with a damp cloth containing a suitable amount of a neutral, dishwashing detergent. Then wipe clean with a damp cloth. When cleaning around the sensor, please be careful not to scratch the surface of the sensor window. Sensor window Do not use detergent that might hurt the surface of spout. These include: Detergents containing acid, chlorine bleach or alkali. Detergents that are coarse granules in nature, such as polishing powder. Solvents such as paint thinner or benzene. Abrasive aids such as nylon scrubbers/brushes, steel wool, etc. 11
Clean the nozzle with a soft brush to remove any dirt form the screen. Nozzle Brush Wash tank out with water to keep it clean. Tank If the pump sticks or backflow occurs, wash pump unit with water while holding upside down and manually squeeze pump several times. Pump unit PERIODIC MAINTENANCE 1. 1.Check all tube connections for any signs of leakage. 2. 2.Wipe away any dust on AC adapter [AC type only]. 1. 1.Check all fixed connections and tighten as needed. 1. 1.Remove soap from tank and wash tank out with water. 2. 2.Fill the tank with water and set up the dispenser as usual. 3. 3.Flush the line with water by activating dispenser until no soap comes out from spout. Refill water if necessary. 4. 4.Discard any water left in tank and allow tank to dry. 5. 5.Place the tank back into the controller. 6. 6.Disconnect the power supply until use resumes. 12
Soap won t stop running Soap comes out unexpectedly TROUBLESHOOTING Problem Operating Cause Solution Green LED flashing Soap is low Fill tank with liquid soap. Red LED flashing Battery is low Replace batteries. Pump is sticking Clean the pump unit. Green LED solid on Change to TOTO No soap comes out Soap viscosity is high approved liquid soap. - Sensor window is dirty Clean sensor window. - Sensor cable is disconnected Connect cable. - There is an obstruction in front of sensor window Remove the obstruction. - Power supply (AC adapter or battery box) is disconnected Connect cable. - Tube is disconnected Connect tube. - AC adapter is not plugged in. Plug in the AC adapter. - Sensor window is dirty Clean sensor window. - There is an obstruction in front of sensor window Remove the obstruction. - Sensor window is dirty Clean sensor window. - Soap will be automatic dispersed after 48 hours of non-usage to prevent clogging. - Amount of dispensed - Pump is not working correctly Clean the pump unit. soap is small Type Power supply Sensor detection range Ambient temperature Humidity Soap volume Tank capacity AC DC 4 D 1.5V Alkaline Batteries 5-7/8±5/8 ( ) 32~104 F (1~40 C) Max. 90% RH 0.03-0.04 oz (0.8 1.2ml) 50 oz (1500ml) 13
FRONT VIEW ROUGH - IN DIMENSIONS 1-7/16 (36mm) Min 1"(25mm) Max 1-1/4"(32mm) 1-3/16 (30mm) max deck thickness 12-3/16 (310mm) 6 ~12 (150~300mm) SIDE VIEW Floor surface 5-4/25 (131mm) Tube lengh:17-3/4 (450mm) Sensor cable length:19-3/4 (500mm) Power cord length:59 (1500mm) 5-3/16 (131mm) 4-5/16 (109mm) Wall Surface 5-3/8 (135mm) Floor surface :(mm) Unit: inches(mm)
LIMITED ONE YEAR WARRANTY WARRANTY 1. TOTO warrants its products to be free from manufacturing defects under normal use and service for a period of one (1) year from the date of purchase. This warranty is extended only to the ORIGINAL PURCHASER. 2. TOTO s obligations under this warranty are limited to repair or replacement, at TOTO s option, of products or parts found to be defective, provided that such products were properly installed and used in accordance with the INSTRUCTION MANUAL. TOTO reserves the right to make such inspections as may be necessary in order to determine the cause of the defect. TOTO will not charge for the labor or parts in connection with warranty repairs or replacements. TOTO is not responsible for the cost of removal, return and/or reinstallation of products. 3. This warranty does not apply to the following items: a) Damage or loss sustained in a natural calamity such as fire, earthquake, flood, thunder, electrical storm, etc. b) Damage or loss resulting from any unreasonable use, misuse, abuse, negligence, or improper maintenance of the product. c) Damage or loss resulting from removal, improper repair or modification of the product. d) Damage or loss resulting from sediments or foreign matter contained in a water system. e) Damage or loss resulting from improper installation or from installation of a unit in a harsh and/or hazardous environment. 4. This warranty gives you specific legal rights. You may have other rights which may vary from Country to Country. 5. To obtain warranty repair service under this warranty, you must take the product or deliver it prepaid to a TOTO service facility together with a letter stating the problem, or contact with a TOTO distributor or products service contractor, or write directly to TOTO sales office. If, because of the size of the product or nature of the defect, the product cannot be returned to TOTO, receipt by TOTO of written notice of the defect shall constitute delivery. In such case, TOTO may choose to repair the product at the purchaser s location or pay to transport the product to a service facility. THIS WRITTEN WARRANTY IS THE ONLY WARRANTY MADE BY TOTO. REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY SHALL BE THE EXCLUSIVE REMEDY AVAILABLE TO THE PURCHASER, TOTO SHALL NOT BE RESPONSIBLE FOR LOSS OF USE OF THE PRODUCT OR FOR OTHER INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES OR EXPENSES INCURRED BY PURCHASER, OR FOR LABOR OR OTHER COSTS DUE TO INSTALLATION OR REMOVAL, OR COSTS OF REPAIRS BY OTHERS, OR FOR ANY OTHER EXPENSE NOT SPECIFICALLY STATED ABOVE. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ANY IMPLIED WARRANTIES, INCLUDING THAT OF MERCHANTABILITY OR FITNESS FOR USE, ARE EXPRESSLY LIMITED TO THE DURATION OF THIS WARRANTY. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, OR THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION AND EXCLUSION MAY NOT APPLY TO YOU. TOTO ASIA OCEANIA PTE. LTD. 10, Eunos Road 8, #12-07, Singapore Post Centre. Singapore 408600. Phone : +65-6744-6955 Fax : +65-6841-0819 http://asia.toto.com/ TOTO LTD. Bangkok Representative Office. G & 7th FL., Q House Ploenjit Building, 598 Ploenchit Rd., Lumpini, Pathumwan, Bangkok, 10330, Thailand. Phone : +66-2-650-9925 Fax : +66-2-650-9923 http://www.totobkk.com/ TOTO ASIA OCEANIA PTE. LTD. Middle East Branch LOB19-1701-1702, Jebel Ali Free Zone, P.O. box 261804, Dubai U.A.E. Phone : +971-4-886-5983 Fax : +971-4-886-5986 http://asia.toto.com/ TOTO INDIA INDUSTRIES PVT. LTD LLTD 101, Kamla Executive Park, Opp. Vazir Glass Works, Off. Andheri Kurla Road, Road,Kurla Road, Andheri (East), Mumbai 400 059, India. Phone : 91-22-4022-3717/3718 Fax 91-22-4022-3719 http://asia.toto.com/ TOTO ASIA OCEANIA PTE. LTD. Manila Representative Office. Unit 1010, 10th Floor Rufino Building, Ayala Avenue cor.v.a. Rufina Street, Makati City,1226 Philippines. Phone : +63-2-887-6643 Fax : +63-2-887-4084 http://asia.toto.com/ TOTO VIETNAM CO., LTD R. 810, Daeha Business Center, 360 Kim Ma Str., Ba Dinh Dist., Ha Noi, Vietnam. Phone : +84-4-37714354 Fax : +84-4-37714355 http://www.toto.com.vn/ 15
16
DSE101E DSE101K