Service Literature Corp. 09-L Revised 7-08 ZHA/ZHB SERIES, 4, 5 and 6 ton 0.6 to kw ZHA/ZHB06, 048, 060, 07 The ZHA/ZHB packaged electric heat pump units are available in standard cooling efficiency (06S, 048S, 060S and 07S). Cooling capacities are, 4, 5 and 6 tons (0.6 to 0kW). Optional electric heat is field-installed and is available in 5kW through 0kW. Electric heat operates in single stage only. Information contained in this manual is intended for use by qualified service technicians only. All specifications are subject to change. Procedures outlined in this manual are presented as a recommendation only and do not supersede or replace local or state codes. If the unit must be lifted for service, rig unit by attaching four cables to the holes located in the unit base rail (two holes at each corner). Refer to the installation instructions for the proper rigging technique. Stacking brackets can be removed or left on the unit permanently. If brackets are removed, any screws removed during installation must be replaced. WARNING Improper installation, adjustment, alteration, service or maintenance can cause property damage, personal injury or loss of life. Installation and service must be performed by a licensed professional installer (or equivalent). WARNING Electric shock hazard. Can cause injury or death. Before attempting to perform any service or maintenance, turn the electrical power to unit OFF at disconnect switch(es). Unit may have multiple power supplies. CAUTION As with any mechanical equipment, contact with sharp sheet metal edges can result in personal injury. Take care while handling this equipment and wear gloves and protective clothing. ELECTROSTATIC DISCHARGE (ESD) Precautions and Procedures CAUTION Electrostatic discharge can affect electronic components. Take precautions to neutralize electrostatic charge by touching your hand and tools to metal prior to handling the control. Table of Contents Options... Page Specifications... Page 4 Blower Data... Page 6 Electrical Data... Page 6 I Unit Components... Page 5 II Placement and Installation... Page III Start Up Operation... Page IV Charging... Page V System Service Checks... Page 9 VI Maintenance... Page 9 VII Accessories... Page 40 VIII Diagrams... Page 46 Page 08
OPTIONS / ACCESSORIES Item Page Catalog No. ZHA ZHB 06 COOLING SYSTEM Condensate Drain Trap PVC - CTRAP0AD 76W6 X X X X Copper - CTRAP0AD 76W7 X X X X Drain Pan Overflow Switch ZSNSR90A 99W59 X X X X Low Ambient Kit ZSNSR4A- 99W68 X X X X Blower - SUPPLY AIR Motors Belt Drive - 0.75 hp (08/0V-ph) Standard Efficiency Factory O O O Belt Drive - hp (08/0V, 460V, 575V-ph) Standard Efficiency Factory O O O O Belt Drive -.5 hp (08/0V-ph or ph, 460V, 575V-ph) Standard Efficiency Factory O O O O Belt Drive- hp (08/0V, 460V, 575V-ph) Standard Efficiency Factory O Drive Kits See Blower Data Tables for selection ZHA ZHB 048 ZHA ZHB 060 ZHB 07 Kit #ZA0-678-05 rpm Factory O Kit #ZA0-80-6 rpm Factory O Kit #ZA0-906-8 rpm Factory 4 O Kit #ZA04-964-47 rpm Factory O Kit #ZA05-098-490 rpm Factory O Kit #ZA06-6-64 rpm Factory 4 O Kit #ZAA0-5-784 rpm Factory O Kit #ZAA0-6-875 rpm Factory O O Kit #ZAA0-798-05 rpm Factory O O Kit #ZAA04-9-8 rpm Factory O CABINET Coil/Hail Guards ZHA models only - ZGARD5A- X9 X X ZHA060 and ZHB models only - ZGARD0AT X0 X X X ZHB07 model only - ZGARD0AL 6A4 X Corrosion Protection Factory O O O O ELECTRICAL Voltage 60 hz 08/0V - phase Factory O O O 08/0V - phase Factory O O O O 460V - phase Factory O O O O 575V - phase Factory O O O O Bottom Power Entry Kit ZPEKT0A- 98W08 X X X X ELECTRIC HEAT 5 kw 08/0V-ph - ZEH0050ANP 98W96 X X X 08/0V-ph - ZEH0050ANY 99W0 X X X 460V-ph - ZEH0050ANG 99W06 X X X 575V-ph - ZEH0050ANJ 99W X X X 7.5 kw 08/0V-ph - ZEH0075ANP 98W97 X X X 08/0V-ph - ZEH0075ANY 99W0 X X X X 460V-ph - ZEH0075ANG 99W07 X X X X 575V-ph - ZEH0075ANJ 99W X X X X 0 kw 08/0V-ph - ZEH000ANP 98W98 X X X 08/0V-ph - ZEH000ANY 99W0 X X X X 460V-ph - ZEH000ANG 99W08 X X X X 575V-ph - ZEH000ANJ 99W X X X X 5 kw 08/0V-ph - ZEH050ANP 98W99 X X X 08/0V-ph - ZEH050ANY 99W04 X X X X 460V-ph - ZEH050ANG 99W09 X X X X 575V-ph - ZEH050ANJ 99W4 X X X X.5 kw 08/0V-ph - ZEH05ANP 99W00 X X 08/0V-ph - ZEH05ANY 99W05 X X X 460V-ph - ZEH05ANG 99W0 X X X 575V-ph - ZEH05ANJ 99W5 X X X 0 kw 08/0V-ph - ZEH000ANY U0 X 460V-PH - ZEH000ANG U0 X 575V-PH - ZEH000ANJ U0 X ELECTRIC HEAT ACCESSORIES Unit Fuse Block (required) - See Electrical/ Tables for Selection X X X X.5 hp blower motor is the minimum required with the ZA05, ZA06 and ZAA0 drive kits. hp blower motor is required with the ZAA04 drive kit. ZHB models only. 4 ZHA models only. NOTE - The catalog and model numbers that appear here are for ordering field installed accessories only. OX - Field Installed or Configure to Order (Factory Installed) O - Configure to Order (Factory Installed) X - Field Installed.
OPTIONS / ACCESSORIES Item Catalog No. ZHA ZHB 06 ECONOMIZER Standard Economizer With Outdoor Hood (Not for Title 4) Standard Economizer (Downflow) ZECON0A- 4D94 OX OX OX OX Includes Barometric Relief Dampers and Exhaust Hood Standard Economizer (Horizontal) ZECON6A- 4D9 X X X X Includes Barometric Relief Dampers and Exhaust Hood Standard Economizer Controls (Not for Title 4) Single Enthalpy Control CSNSR64FF 5W64 X X X X High Performance Economizer With Outdoor Hood (Approved for California Title 4 Building Standards / AMCA Class A Certified) High Performance Economizer (Downflow) ZECONA- 4D95 OX OX OX OX Includes Barometric Relief Dampers and Exhaust Hood High Performance Economizer (Horizontal) ZECONA- 4D9 X X X X Includes Barometric Relief Dampers and Exhaust Hood High Performance Economizer Controls (Not for Title 4) Single Enthalpy Control CSNSR6FF G X X X X OUTDOOR AIR Outdoor Dampers - Includes Outdoor Hood Motorized ZDAMPA- 5D9 X X X X Manual ZDAMPA- 5D0 X X X X Power EXhaust FAN Standard Static (Downflow) 08/0V- or ph - ZPWRE0A-P E0 X X X X 460V-ph - ZPWRE0A-G E0 X X X X Standard Static (Horizontal) 08/0V- or ph - ZPWRE5A-P 4E0 X X X X 460V-ph - ZPWRE5A-G 8E0 X X X X 575V Transformer Kit 575V-ph - ZTRFM0A-J 59E0 X X X X NOTE - Order 575V Transformer Kit with 08/0V Fan for 575V applications. Indoor Quality Indoor Quality (Co ) Sensors Sensor - Wall-mount, off-white plastic cover with LCD display C0SNSR50AEL 77N9 X X X X Sensor - Wall-mount, black plastic case, no display, rated for C0SNSR5AEL 87N54 X X X X plenum mounting CO Sensor Duct Mounting Kit - for downflow applications C0MISC9AE 85L4 X X X X Aspiration Box - for duct mounting non-plenum rated CO sensor C0MISC6AE 90N4 X X X X (77N9) ROOF CURBS Hybrid Roof Curbs, Downflow 8 in. height ZCURB70A- F76 X X X X 4 in. height ZCURB7A- F77 X X X X 8 in. height ZCURB7A- F78 X X X X 4 in. height ZCURB7A- F79 X X X X CEILING DIFFUSERS Step-Down - Order one RTD9-65S K60 X X X RTD-95S K6 X Flush - Order one FD9-65S K55 X X X FD-95S K56 X NOTE - Ceiling Diffuser Transitions are not furnished and must be field fabricated. NOTE - The catalog and model numbers that appear here are for ordering field installed accessories only. OX - Field Installed or Configure to Order (Factory Installed) O - Configure to Order (Factory Installed) X - Field Installed. Page ZHA ZHB 048 ZHA ZHB 060 ZHB 07
SPECIFICATIONS - ZHA General Data Nominal Tonnage Ton 4 Ton 5 Ton Model No. ZHA06S4B ZHA048S4B ZHA060S4B Efficiency Type Standard Standard Standard Cooling Gross Cooling Capacity - Btuh 7,600 48,500 60,700 Performance Net Cooling Capacity - Btuh 6,00 46,500 58,000 AHRI Rated Flow - 0 60 940 Sound Rating Number (SRN) (dba) Cooling 79 79 8 Heating 80 80 8 Total Unit Power - kw. 4. 5. SEER (Btuh/Watt).00.00.00 EER (Btuh/Watt). 0.8 0.9 Refrigerant Type R-40A R-40A R-40A Charge Furnished lbs. oz. lbs. 8 oz. 5 lbs. oz. Heating Performance Total High Heating Capacity - Btuh 4,00 45,000 58,500 Total Unit Power - kw.9.9 4.9 COP.4.40.50 HSPF - Region IV (Region V) 7.70 (6.70) 7.70 (6.70) 7.70 (6.70) Total Low Heating Capacity - Btuh 0,400 7,400,400 Total Unit Power - kw.8.6 4.5 COP.8.4.0 Available 5, 7.5, 0, 5 kw 5, 7.5, 0, 5,.5 kw Compressor Type (one per unit) Scroll Scroll Scroll Outdoor Coil Net face area - sq. ft. 6. 6. 9.9 Tube diameter - in. /8 /8 /8 Number of rows Fins / inch 0 0 0 Expansion device type Balanced port TXV, removable head Outdoor Coil Fan Motor HP () /4 (PSC) () /4 (PSC) () / (PSC) Motor rpm 85 85 075 Total motor watts 00 00 40 Diameter - in. () () () Number of blades 4 4 Total air volume - 00 00 600 Indoor Coil Net face area - sq. ft. 8.4 8.4 9.6 Tube diameter - in. /8 /8 /8 Number of rows Fins per inch 4 4 4 Drain Connection (no.and size) - in. () NPT () NPT () NPT Expansion device type Fixed Orifice Fixed Orifice Fixed Orifice Indoor Blower & Drive Selection Nominal Motor HP hp,.5 hp hp,.5 hp hp,.5 hp Maximum Usable Motor HP.5 hp,.7 hp.5 hp,.7 hp.5 hp,.7 hp Available Drive Kits Kit #ZA0 678-05 rpm Kit #ZA04 964-47 rpm Kit #ZA0 80-6 rpm 5 Kit #ZA05 098-490 rpm Kit #ZA0 906-8 rpm 5 Kit #ZA06 6-64 rpm Wheel nominal diameter x width - in. 0 x 0 0 x 0 0 x 0 Filters Type Disposable Number and size - in. (4) 4 x 0 x (4) 4 x 0 x (4) 6 x 0 x Electrical Characteristics - 60 Hz 08/0V, 460V & 575V phase 08/0V 460V & 575V phase 08/0V 460V & 575V phase NOTE - Net capacity includes evaporator blower motor heat deduction. Gross capacity does not include evaporator blower motor heat deduction. AHRI Certified to AHRI Standard 0/40: Cooling Ratings - 95 F outdoor air temperature and 80 F db/67 F wb entering indoor coil air. High Temperature Heating Ratings - 47 F db/4 F wb outdoor air temperature and 70 F entering indoor coil air. Low Temperature Heating Ratings - 7 F db/5 F wb outdoor air temperature and 70 F entering indoor coil air. Sound Rating Number (SRN) rated in accordance with test conditions included in ANSI/AHRI Standard 70-008. Using total air volume and system static pressure requirements determine from blower performance tables rpm and motor hp required. Maximum usable hp of motors furnished are shown. In Canada, nominal motor hp is also maximum usable motor hp output. If motors of comparable hp are used, be sure to keep within the service factor limitations outlined on the motor nameplate. 5.5 hp motor is the minimum required with ZA05 and ZA06 drive kits. Page 4
SPECIFICATIONS - ZHB General Data Nominal Tonnage Ton 4 Ton 5 Ton 6 Ton Model No. ZHB06S4B ZHB048S4B ZHB060S4B ZHB07S4B Efficiency Type Standard Standard Standard Standard Cooling Performance Gross Cooling Capacity - Btuh 6,00 47,900 59,700 7,000 Net Cooling Capacity - Btuh 5,000 46,500 58,000 69,000 AHRI Rated Flow - 60 50 05 860 Sound Rating Number (SRN) (dba) Cooling 79 78 8 86 Total Unit Power - kw. 4. 5. 6.4 SEER (Btuh/Watt) 4.00 4.00 4.00 - - - IEER (Btuh/Watt) - - - - - - - - -.0 EER (Btuh/Watt).40.0.0.00 Refrigerant Type R-40A R-40A R-40A R-40A Charge Furnished 4 lbs. 8 oz. 6 lbs. 5 oz. 4 lbs. 4 oz. 8 lbs. 0 oz. Heating Performance Total High Heating Capacity - Btuh 4,00 45,000 55,000 70,000 Total Unit Power - kw.9.8 4.5 6. COP.50.50.60.0 HSPF - Region IV (Region V) 8.00 (6.70) 8.00 (6.70) 8.00 (6.70) - - - Total Low Heating Capacity - Btuh 0,000 6,00,500 40,000 Total Unit Power - kw.7.5 4. 5.4 COP.0.0.5.5 Available 5, 7.5, 0, 5 kw 5, 7.5, 0, 5,.5 kw 7.5,0,5,.5, 0 kw Compressor Type (one per unit) Scroll Scroll Scroll Scroll Outdoor Coil Net face area - sq. ft. 9.9 9.9 9.9 5.0 Tube diameter - in. /8 /8 /8 /8 Number of rows Fins / inch 0 0 0 0 Outdoor Coil Fan Expansion device type Balanced port TXV, removable head Motor HP () /4 () /4 () / () / Motor rpm 85 85 075 050 Total motor watts 00 00 50 50 Diameter - in. () () () () 4 Number of blades 4 4 Total air volume - 5 5 600 450 Indoor Coil Net face area - sq. ft. 9.6 0.8 0.8 0.8 Tube diameter - in. /8 /8 /8 /8 Number of rows Fins per inch 4 4 4 4 Drain Connection (no.and size) - in. () NPT () NPT () NPT () NPT 4 Indoor Blower & Drive Selection Expansion device type Fixed Orifice Fixed Orifice Fixed Orifice Nominal Motor HP 5 0.75 hp, 6 5 hp, 0.75 hp, 6 5 hp, 0.75 hp, 6 hp,.5 hp.5 hp.5 hp Maximum Usable Motor HP 0.86 hp,.5 hp, 0.86 hp,.5 hp, 0.86 hp,.7 hp.7 hp.5 hp,.7 hp Available Drive Kits Kit #ZA0 Kit #ZA0 Kit #ZAA0 678-05 rpm 80-6 rpm 5-784 rpm Kit #ZA04 964-47 rpm 7 Kit #ZA05 098-490 rpm Kit #ZAA0 6-875 rpm 7 Kit #ZAA0 798-05 rpm Balanced port TXV, removable power head hp,.5 hp, hp.5 hp,.7 hp,. hp Kit #ZAA0 6-875 rpm 7 Kit #ZAA0 798-05 rpm 8 Kit #ZAA04 9-8 rpm Wheel nominal diameter x width - in. 0 x 0 0 x 0 5 x 9 5 x 9 Filters Type Disposable Number and size - in. (4) 6 x 0 x () 6 x 0 x () 0 x 0 x () 6 X 0 X () 0 X 0 X Electrical Characteristics - 60 Hz 08/0V 08/0V, 08/0V, phase phase phase 08/0V, 460V & 575V phase 08/0V 460V & 575V phase 08/0V 460V & 575V phase NOTE - Net capacity includes evaporator blower motor heat deduction. Gross capacity does not include evaporator blower motor heat deduction. () 0 x 0 x () 6 x 0 x 08/0V 460V & 575V Phase, AHRI Certified to AHRI Standard 0/40 or 40/60: Cooling Ratings - 95 F outdoor air temperature and 80 F db/67 F wb entering indoor coil air. High Temperature Heating Ratings - 47 F db/4 F wb outdoor air temperature and 70 F entering indoor coil air. Low Temperature Heating Ratings - 7 F db/5 F wb outdoor air temperature and 70 F entering indoor coil air. Sound Rating Number (SRN) rated in accordance with test conditions included in ANSI/AHRI Standard 70-008. 4 Using total air volume and system static pressure requirements determine from blower performance tables rpm and motor hp required. Maximum usable hp of motors furnished are shown. In Canada, nominal motor hp is also maximum usable motor hp output. If motors of comparable hp are used, be sure to keep within the service factor limitations outlined on the motor nameplate. 5 0.75 hp motor is only available for 08/0V-ph applications. 6 hp blower motor is not available for 08/0V-ph applications. 7.5 hp motor is the minimum required with ZA05 and ZAA0 drive kits. 8 Page 5.0 hp motor is required with ZAA04 drive kits.
BLOWER DATA - BELT DRIVE - ZHA06 BLOWER TABLE INCLUDES RESISTANCE FOR BASE UNIT ONLY WITH DRY INDOOR COIL AND AIR FILTERS IN PLACE. FOR ALL UNITS ADD: - Any factory installed options air resistance (heat section, economizer, wet coil, etc.). - Any field installed accessories air resistance (duct resistance, diffuser, etc.). See page for blower motors and drives and wet coil and options/accessory air resistance data. DOWNFLOW Volume 0.0 0.0 0.0 0.40 0.50 0.60 0.70 0.80 900 56 0.6 69 0.8 699 0.9 77 0. 840 0. 904 0.4 96 0.6 05 0.9 000 586 0.8 654 0. 75 0. 796 0. 864 0.5 97 0.7 98 0. 04 0. 00 6 0. 68 0. 75 0.4 8 0.6 890 0.8 950 0. 004 0.4 054 0.7 00 64 0. 7 0.5 78 0.7 85 0.9 97 0. 975 0.5 07 0.9 074 0.4 00 67 0.5 744 0.8 85 0. 88 0. 944 0.6 000 0.4 050 0.44 096 0.48 400 709 0.9 779 0. 849 0.4 94 0.7 97 0.4 06 0.45 074 0.49 8 0.5 500 747 0. 86 0.6 88 0.9 945 0.4 00 0.46 05 0.5 098 0.55 4 0.59 Volume 0.90.00.0.0.0.40.50.60 900 065 0. 0.5 58 0.8 0 0.4 4 0.44 84 0.48 0.5 64 0.55 000 08 0.6 8 0.9 7 0.4 6 0.45 57 0.49 97 0.5 6 0.57 75 0.6 00 00 0.4 45 0.44 89 0.47 0.5 7 0.54 0.58 49 0.6 88 0.66 00 9 0.45 6 0.49 06 0.5 47 0.56 87 0.6 6 0.64 64 0.68 40 0.7 00 9 0.5 8 0.55 4 0.58 65 0.6 04 0.66 4 0.7 79 0.75 46 0.79 400 60 0.57 0 0.6 4 0.65 8 0.69 0.7 59 0.78 96 0.8 4 0.87 500 8 0.64 0.68 6 0.7 0 0.76 4 0.8 78 0.85 44 0.9 449 0.94 HORIZONTAL Volume 0.0 0.0 0.0 0.40 0.50 0.60 0.70 0.80 900 580 0.4 649 0.7 7 0.9 794 0. 868 0.4 98 0.7 998 0. 045 0. 000 6 0.7 68 0.9 75 0. 85 0.5 897 0.7 96 0. 07 0. 06 0.7 00 647 0. 77 0. 788 0.6 858 0.8 96 0. 986 0.4 06 0.8 077 0.4 00 687 0. 757 0.6 86 0.9 89 0. 955 0.5 008 0.9 054 0.4 095 0.46 00 70 0.7 798 0. 864 0. 96 0.7 98 0.4 00 0.44 07 0.47 6 0.5 400 775 0. 840 0.4 90 0.8 959 0.4 009 0.46 054 0.5 096 0.5 40 0.56 500 80 0.6 88 0.4 99 0.44 99 0.49 09 0.5 08 0.56 4 0.59 68 0.6 Volume 0.90.00.0.0.0.40.50.60 900 09 0.6 40 0.8 88 0.4 0.4 7 0.46 09 0.49 46 0.5 8 0.57 000 05 0.4 54 0.4 0 0.45 45 0.47 84 0.5 0.54 57 0.58 94 0.6 00 0.44 69 0.47 6 0.49 59 0.5 98 0.56 5 0.6 70 0.64 406 0.69 00 9 0.49 87 0.5 4 0.54 76 0.58 4 0.6 50 0.66 85 0.7 4 0.75 00 6 0.54 08 0.57 54 0.6 95 0.64 0.69 66 0.7 40 0.78 46 0.8 400 85 0.59 0.6 76 0.67 5 0.7 5 0.76 84 0.8 49 0.86 454 0.9 500 0.66 57 0.7 99 0.74 7 0.79 7 0.84 404 0.89 48 0.94 47 0.99 Page 6
BLOWER DATA - BELT DRIVE - ZHA048 BLOWER TABLE INCLUDES RESISTANCE FOR BASE UNIT ONLY WITH DRY INDOOR COIL AND AIR FILTERS IN PLACE. FOR ALL UNITS ADD: - Any factory installed options air resistance (heat section, economizer, wet coil, etc.). - Any field installed accessories air resistance (duct resistance, diffuser, etc.). See page for blower motors and drives and wet coil and options/accessory air resistance data. DOWNFLOW Volume 0.0 0.0 0.0 0.40 0.50 0.60 0.70 0.80 00 64 0. 7 0.5 78 0.7 85 0.9 97 0. 975 0.5 07 0.9 074 0.4 00 67 0.5 744 0.8 85 0.0 88 0. 944 0.6 000 0.40 050 0.44 096 0.48 400 709 0.9 779 0. 849 0.4 94 0.7 97 0.4 06 0.45 074 0.49 8 0.5 500 747 0. 86 0.6 88 0.9 945 0.4 00 0.46 05 0.5 098 0.55 4 0.59 600 787 0.8 854 0.4 98 0.44 976 0.48 00 0.5 078 0.56 0.6 64 0.66 700 87 0.4 89 0.46 95 0.49 007 0.5 058 0.58 05 0.6 48 0.68 89 0.7 800 868 0.48 99 0.5 986 0.55 08 0.59 087 0.64 0.69 74 0.75 4 0.80 900 907 0.54 966 0.58 09 0.6 069 0.66 6 0.7 60 0.77 00 0.8 40 0.88 000 946 0.60 00 0.65 05 0.69 0 0.74 46 0.79 88 0.85 8 0.9 67 0.98 Volume 0.90.00.0.0.0.40.50.60 00 9 0.45 6 0.49 06 0.5 47 0.56 87 0.60 6 0.64 64 0.68 40 0.7 00 9 0.5 8 0.55 4 0.58 65 0.6 04 0.66 4 0.7 79 0.75 46 0.79 400 60 0.57 0 0.6 4 0.65 8 0.69 0.7 59 0.78 96 0.8 4 0.87 500 8 0.64 0.68 6 0.7 0 0.76 4 0.8 78 0.85 44 0.90 449 0.94 600 05 0.70 45 0.75 84 0.79 0.84 6 0.88 97 0.9 4 0.98 467.0 700 8 0.78 68 0.8 07 0.87 45 0.9 8 0.97 47.0 45.07 486. 800 5 0.85 9 0.9 0.96 68.0 404.06 49. 47.6 506. 900 79 0.94 7.00 55.05 9.0 47.6 46. 494.6 57. 000 05.04 4.0 80.5 46. 450.6 484. 56.7 549.4 HORIZONTAL Volume 0.0 0.0 0.0 0.40 0.50 0.60 0.70 0.80 00 687 0. 757 0.6 86 0.9 89 0. 955 0.5 008 0.9 054 0.4 095 0.46 00 70 0.7 798 0.0 864 0. 96 0.7 98 0.40 00 0.44 07 0.47 6 0.5 400 775 0. 840 0.4 90 0.8 959 0.4 009 0.46 054 0.50 096 0.5 40 0.56 500 80 0.6 88 0.40 99 0.44 99 0.49 09 0.5 08 0.56 4 0.59 68 0.6 600 864 0.4 9 0.46 976 0.5 07 0.56 07 0.60 0.6 55 0.66 98 0.69 700 907 0.48 96 0.5 0 0.58 06 0.6 05 0.67 46 0.70 87 0.7 0 0.77 800 948 0.56 999 0.6 049 0.66 096 0.7 9 0.75 80 0.78 0.8 6 0.86 900 987 0.64 07 0.69 086 0.74 0.79 74 0.8 4 0.86 55 0.90 95 0.95 000 08 0.7 076 0.78 0.8 68 0.87 0 0.9 50 0.96 89.00 8.06 Volume 0.90.00.0.0.0.40.50.60 00 9 0.49 87 0.5 4 0.54 76 0.58 4 0.6 50 0.66 85 0.7 4 0.75 00 6 0.54 08 0.57 54 0.60 95 0.64 0.69 66 0.7 40 0.78 46 0.8 400 85 0.59 0.6 76 0.67 5 0.7 5 0.76 84 0.8 49 0.86 454 0.90 500 0.66 57 0.70 99 0.74 7 0.79 7 0.84 404 0.89 48 0.94 47 0.99 600 4 0.7 84 0.77 4 0.8 60 0.88 94 0.9 46 0.99 460.04 495.08 700 7 0.8 0.86 50 0.9 85 0.98 48.04 45.09 485.4 59.9 800 0 0.90 4 0.96 77.0 4.08 444.5 477.0 50.5 544.0 900 4.0 7.07 406. 49.0 47.6 504. 57.7 57.4 000 65. 40.9 45.5 468. 500.8 5.44 565.49 598.5 Page 7
BLOWER DATA - BELT DRIVE - ZHA060 BLOWER TABLE INCLUDES RESISTANCE FOR BASE UNIT ONLY WITH DRY INDOOR COIL AND AIR FILTERS IN PLACE. FOR ALL UNITS ADD: - Any factory installed options air resistance (heat section, economizer, wet coil, etc.). - Any field installed accessories air resistance (duct resistance, diffuser, etc.). See page for blower motors and drives and wet coil and options/accessory air resistance data. DOWNFLOW Volume 0.0 0.0 0.0 0.40 0.50 0.60 0.70 0.80 600 764 0.5 8 0.9 880 0.4 96 0.46 99 0.5 04 0.55 09 0.60 6 0.64 700 80 0.40 857 0.44 9 0.48 968 0.5 00 0.57 070 0.6 7 0.66 6 0.7 800 88 0.46 89 0.50 947 0.54 000 0.58 05 0.6 099 0.68 45 0.7 88 0.78 900 876 0.5 99 0.56 98 0.6 0 0.65 08 0.70 9 0.75 7 0.80 5 0.85 000 94 0.59 966 0.6 07 0.68 067 0.7 5 0.77 60 0.8 0 0.88 44 0.94 00 95 0.66 004 0.7 054 0.76 0 0.8 48 0.86 9 0.9 0.98 7.04 00 99 0.74 04 0.79 090 0.85 7 0.90 8 0.96 4.0 64.09 0.5 00 0 0.8 08 0.89 8 0.94 7.0 6.07 57.4 96.0 4.7 400 074 0.9 0 0.99 66.05 09. 5.9 9.6 9. 66.4 Volume 0.90.00.0.0.0.40.50.60 600 80 0.68 0.7 6 0.76 0 0.80 4 0.85 78 0.90 44 0.94 449 0.99 700 04 0.75 45 0.79 85 0.84 5 0.88 6 0.9 98 0.98 44.0 468.08 800 9 0.8 70 0.87 09 0.9 47 0.97 84.0 40.07 454. 488.7 900 56 0.9 96 0.96 4.0 7.07 407. 44.7 476. 509.8 000 84.00.06 60. 96.7 4. 465.8 498. 5.8 00.0 50.6 86. 4.8 456.4 489.40 5.45 554.50 00 4. 78.8 44.4 448.4 48.46 5.5 546.57 578.6 00 7.4 407.4 44.47 475.54 507.59 59.65 57.70 60.75 400 40.48 46.55 470.6 50.67 55.7 566.79 597.84 68.89 HORIZONTAL Volume 0.0 0.0 0.0 0.40 0.50 0.60 0.70 0.80 600 78 0.8 844 0.4 90 0.44 957 0.48 008 0.5 056 0.56 00 0.60 4 0.64 700 85 0.44 88 0.47 98 0.50 989 0.54 08 0.57 08 0.6 6 0.66 66 0.7 800 866 0.50 9 0.5 97 0.56 0 0.60 067 0.64 0.68 5 0.7 9 0.78 900 907 0.56 959 0.59 008 0.6 054 0.66 098 0.7 9 0.75 79 0.80 7 0.86 000 948 0.6 996 0.66 04 0.70 086 0.74 8 0.78 68 0.8 07 0.89 44 0.94 00 987 0.70 0 0.74 077 0.78 9 0.8 59 0.87 98 0.9 5 0.99 7.05 00 06 0.78 070 0.8 0.87 5 0.9 9 0.98 8.0 65.0 0.6 00 064 0.88 06 0.9 47 0.97 86.0.09 60.5 95..8 400 0 0.98 4.0 8.08 0.5 56. 9.8 7.5 6.4 Volume 0.90.00.0.0.0.40.50.60 600 8 0.68 0.7 6 0.76 0 0.8 40 0.86 77 0.9 4 0.95 448.00 700 05 0.75 45 0.79 84 0.84 0.89 60 0.94 96 0.99 4.04 465.09 800 0 0.8 68 0.87 06 0.9 44 0.98 80.0 46.08 450. 48.9 900 55 0.9 9 0.96 0.0 67.07 40. 47.8 470.4 50.9 000 8.00 8.06 55. 9.8 45. 459.9 49.5 54.40 00 08. 45.7 8. 46.9 450.5 48.4 54.46 546.5 00 7. 7.9 408.5 44.4 475.47 507.5 58.59 569.64 00 66.5 40.4 45.49 469.55 50.6 5.67 56.7 594.77 400 96.49 4.56 464.6 496.69 58.75 559.8 589.86 69.9 Page 8
BLOWER DATA - BELT DRIVE - ZHB06 BLOWER TABLE INCLUDES RESISTANCE FOR BASE UNIT ONLY WITH DRY INDOOR COIL AND AIR FILTERS IN PLACE. FOR ALL UNITS ADD: - Any factory installed options air resistance (heat section, economizer, wet coil, etc.). - Any field installed accessories air resistance (duct resistance, diffuser, etc.). See page for blower motors and drives and wet coil and options/accessory air resistance data. DOWNFLOW Volume 0.0 0.0 0.0 0.40 0.50 0.60 0.70 0.80 900 56 0. 6 0. 685 0.6 75 0.8 88 0. 88 0.4 944 0.7 00 0.0 000 584 0. 644 0.6 707 0.8 77 0. 88 0.4 90 0.7 960 0. 05 0. 00 609 0.6 669 0.8 7 0. 796 0.4 860 0.7 9 0.0 978 0.4 0 0.7 00 65 0.9 696 0. 758 0.4 8 0.7 88 0. 94 0.4 997 0.8 049 0.4 00 664 0. 75 0.5 786 0.8 848 0. 908 0.5 965 0.9 08 0.4 068 0.47 400 696 0.6 756 0.9 86 0. 876 0.6 95 0.40 989 0.44 04 0.48 089 0.5 500 79 0.0 788 0. 848 0.7 906 0.4 96 0.45 05 0.50 065 0.54 0.58 Volume 0.90.00.0.0.0.40.50.60 900 05 0. 0 0.5 49 0.8 9 0.4 4 0.4 74 0.47 0.50 5 0.5 000 066 0.6 4 0.9 60 0.4 04 0.45 45 0.48 84 0.5 0.54 6 0.58 00 08 0.40 8 0.4 7 0.46 6 0.49 57 0.5 96 0.56 4 0.60 7 0.6 00 097 0.45 44 0.48 88 0.5 0.54 7 0.58 0 0.6 47 0.66 85 0.69 00 5 0.50 6 0.5 04 0.56 46 0.60 86 0.64 5 0.68 6 0.7 99 0.76 400 5 0.56 79 0.59 0.6 64 0.66 0 0.70 4 0.75 78 0.79 45 0.8 500 57 0.6 00 0.65 4 0.69 8 0.7 0.77 59 0.8 96 0.86 4 0.9 HORIZONTAL Volume 0.0 0.0 0.0 0.40 0.50 0.60 0.70 0.80 900 560 0.6 64 0.8 69 0.0 76 0. 80 0. 896 0.5 956 0.7 0 0.9 000 58 0.8 647 0.0 75 0. 78 0.4 850 0.5 94 0.7 97 0.0 05 0. 00 609 0.0 67 0. 740 0.4 808 0.6 87 0.8 94 0. 990 0.4 04 0.7 00 67 0. 70 0.5 769 0.7 85 0.9 898 0. 956 0.5 009 0.8 058 0.4 00 669 0.6 74 0.8 800 0.0 86 0. 94 0.6 979 0.9 00 0.4 077 0.46 400 704 0.9 768 0. 8 0.5 894 0.7 95 0.4 004 0.44 05 0.48 097 0.5 500 74 0. 805 0.6 867 0.9 95 0.4 980 0.46 00 0.50 076 0.54 9 0.58 Volume 0.90.00.0.0.0.40.50.60 900 064 0. 4 0.5 6 0.8 08 0.4 5 0.45 9 0.49 0.5 7 0.56 000 076 0.6 4 0.9 70 0.4 6 0.46 59 0.49 00 0.5 40 0.57 79 0.6 00 089 0.40 6 0.4 8 0.46 5 0.50 68 0.54 08 0.58 47 0.6 86 0.66 00 04 0.45 50 0.48 94 0.5 7 0.55 79 0.59 9 0.6 57 0.67 94 0.7 00 0.5 65 0.5 09 0.57 5 0.6 9 0.65 0.69 68 0.7 405 0.78 400 40 0.56 8 0.59 5 0.6 66 0.67 06 0.7 45 0.76 8 0.8 47 0.85 500 6 0.6 0 0.65 4 0.69 84 0.7 0.78 60 0.8 96 0.87 4 0.9 Page 9
BLOWER DATA - BELT DRIVE - ZHB048 BLOWER TABLE INCLUDES RESISTANCE FOR BASE UNIT ONLY WITH DRY INDOOR COIL AND AIR FILTERS IN PLACE. FOR ALL UNITS ADD: - Any factory installed options air resistance (heat section, economizer, wet coil, etc.). - Any field installed accessories air resistance (duct resistance, diffuser, etc.). See page for blower motors and drives and wet coil and options/accessory air resistance data. DOWNFLOW Volume 0.0 0.0 0.0 0.40 0.50 0.60 0.70 0.80 00 60 0. 68 0.9 744 0.4 809 0.9 875 0.4 94 0.47 004 0.5 060 0.54 00 65 0.8 7 0.4 775 0.9 89 0.44 90 0.48 967 0.5 05 0.55 078 0.59 400 687 0. 747 0.9 809 0.44 87 0.49 94 0.5 994 0.57 048 0.6 098 0.64 500 74 0.40 784 0.45 844 0.50 905 0.54 965 0.59 0 0.6 07 0.66 8 0.70 600 764 0.46 8 0.5 88 0.56 940 0.60 997 0.65 048 0.69 094 0.7 40 0.75 700 806 0.5 86 0.58 99 0.6 975 0.67 08 0.7 075 0.75 9 0.78 64 0.8 800 849 0.60 90 0.65 957 0.69 00 0.74 058 0.78 0 0.8 45 0.85 89 0.88 900 89 0.68 944 0.7 995 0.77 045 0.8 089 0.86 0.89 74 0.9 7 0.95 000 95 0.76 984 0.8 0 0.86 079 0.9 0.95 6 0.97 04.00 47.0 Volume 0.90.00.0.0.0.40.50.60 00 0.58 56 0.60 99 0.6 4 0.6 84 0.65 6 0.67 67 0.7 408 0.74 00 7 0.6 7 0.65 4 0.66 56 0.68 99 0.70 4 0.7 8 0.77 4 0.8 400 45 0.68 89 0.70 0.7 74 0.74 6 0.76 57 0.79 97 0.8 46 0.88 500 64 0.7 08 0.75 5 0.78 9 0.80 4 0.8 74 0.86 4 0.9 45 0.95 600 85 0.79 9 0.8 7 0.84 0.86 54 0.90 9 0.94 4 0.98 468.0 700 08 0.84 5 0.87 94 0.90 5 0.94 75 0.98 4.0 449.07 485. 800 0.9 76 0.94 8 0.98 58.0 97.06 44. 469.6 504. 900 6 0.98 0.0 4.06 8. 40.6 455. 490.6 55. 000 89.07 0. 70.6 407. 444.7 478. 5.7 547.4 HORIZONTAL Volume 0.0 0.0 0.0 0.40 0.50 0.60 0.70 0.80 00 64 0. 68 0.5 75 0.0 8 0.4 888 0.9 950 0.4 006 0.46 057 0.49 00 644 0.4 7 0.9 78 0.4 850 0.9 95 0.4 974 0.47 07 0.5 076 0.5 400 677 0.9 746 0.4 84 0.9 880 0.44 94 0.48 998 0.5 049 0.55 097 0.58 500 74 0.4 78 0.40 848 0.45 9 0.49 970 0.5 0 0.57 07 0.60 9 0.6 600 75 0.40 88 0.45 88 0.50 94 0.55 999 0.59 050 0.6 097 0.66 4 0.69 700 79 0.46 855 0.5 97 0.56 975 0.6 08 0.64 077 0.68 0.7 66 0.75 800 8 0.5 894 0.58 95 0.6 007 0.67 058 0.70 05 0.74 49 0.78 9 0.8 900 87 0.60 9 0.65 988 0.69 040 0.7 088 0.77 4 0.8 77 0.85 9 0.90 000 94 0.67 970 0.7 0 0.76 07 0.80 0 0.85 6 0.89 05 0.94 46 0.99 Volume 0.90.00.0.0.0.40.50.60 00 05 0.5 5 0.5 97 0.55 40 0.58 80 0.6 0 0.64 58 0.68 95 0.7 00 0.55 69 0.57 0.60 55 0.6 95 0.67 4 0.70 7 0.74 409 0.79 400 4 0.60 87 0.6 0 0.66 7 0.69 0.7 50 0.77 88 0.8 44 0.86 500 6 0.66 07 0.69 49 0.7 90 0.76 0 0.80 68 0.85 405 0.90 44 0.94 600 85 0.7 8 0.75 70 0.79 0 0.8 49 0.88 87 0.9 4 0.98 459.0 700 09 0.78 5 0.8 9 0.87 0.9 70 0.97 407.0 44.07 478. 800 4 0.86 75 0.9 5 0.96 54.0 9.06 48. 46.7 498. 900 60 0.95 00.00 40.05 77. 44.6 450. 485.7 59. 000 87.04 6.0 65.6 40. 47.7 47. 507.8 54.4 Page 0
BLOWER DATA - BELT DRIVE - ZHB060 BLOWER TABLE INCLUDES RESISTANCE FOR BASE UNIT ONLY WITH DRY INDOOR COIL AND AIR FILTERS IN PLACE. FOR ALL UNITS ADD: - Any factory installed options air resistance (heat section, economizer, wet coil, etc.). - Any field installed accessories air resistance (duct resistance, diffuser, etc.). See page for blower motors and drives and wet coil and options/accessory air resistance data. DOWNFLOW Volume 0.0 0.0 0.0 0.40 0.50 0.60 0.70 0.80 600 5 0.7 55 0. 585 0.7 69 0.4 656 0.48 69 0.5 7 0.59 77 0.64 700 59 0. 570 0.7 60 0.4 68 0.48 674 0.5 7 0.59 749 0.64 787 0.69 800 558 0.8 589 0.4 6 0.48 658 0.54 694 0.59 70 0.64 767 0.70 80 0.75 900 578 0.44 60 0.49 64 0.54 678 0.60 74 0.65 749 0.70 785 0.76 89 0.8 000 600 0.50 6 0.56 665 0.6 699 0.66 74 0.7 769 0.77 80 0.8 87 0.90 00 6 0.57 655 0.6 688 0.68 7 0.7 755 0.79 789 0.84 8 0.9 854 0.98 00 647 0.65 678 0.70 7 0.75 74 0.8 776 0.86 809 0.9 84.00 87.06 00 67 0.7 70 0.78 74 0.8 766 0.89 798 0.95 89.0 860.09 890.6 400 696 0.8 76 0.87 757 0.9 788 0.98 89.04 850. 880.9 909.6 Volume 0.90.00.0.0.0.40.50.60 600 809 0.69 844 0.74 877 0.80 908 0.85 96 0.9 96 0.97 989.0 04.08 700 8 0.75 857 0.80 889 0.86 99 0.9 947 0.97 97.0 999.09 04.4 800 88 0.8 870 0.87 90 0.9 9 0.98 958.04 984.0 009.6 04. 900 85 0.88 885 0.94 95 0.99 944.05 97. 996.7 0. 045.9 000 869 0.96 899.0 99.07 957. 984.9 009.5 0. 058.8 00 885.04 95.0 944.5 97. 997.8 0.4 046.40 070.46 00 90. 9.9 959.4 986. 0.7 06.4 060.50 084.56 00 90. 948.9 975.5 00.4 07.47 05.5 075.60 098.66 400 98. 965.9 99.45 07.5 04.58 066.64 090.70.77 HORIZONTAL Volume 0.0 0.0 0.0 0.40 0.50 0.60 0.70 0.80 600 55 0.0 56 0.4 597 0.9 65 0.4 67 0.47 7 0.5 748 0.56 784 0.6 700 54 0.4 578 0.9 65 0.4 65 0.48 69 0.5 78 0.57 765 0.6 800 0.67 800 56 0.9 597 0.44 65 0.49 67 0.5 70 0.58 746 0.6 78 0.68 86 0.7 900 58 0.44 68 0.49 655 0.54 69 0.59 79 0.64 765 0.69 800 0.75 8 0.80 000 60 0.50 69 0.55 676 0.6 7 0.66 749 0.7 784 0.76 88 0.8 850 0.88 00 65 0.57 66 0.6 698 0.67 75 0.7 770 0.78 804 0.84 87 0.90 868 0.96 00 648 0.64 685 0.69 7 0.75 757 0.80 79 0.86 84 0.9 856 0.98 886.05 00 67 0.7 709 0.77 745 0.8 780 0.88 8 0.94 845.0 876.08 905.5 400 699 0.79 74 0.85 769 0.9 80 0.97 85.04 866. 896.8 94.5 Volume 0.90.00.0.0.0.40.50.60 600 89 0.66 85 0.7 88 0.77 9 0.8 94 0.89 97 0.95 998.0 04.07 700 8 0.7 865 0.78 896 0.84 96 0.90 954 0.96 98.0 009.08 04.4 800 848 0.79 880 0.85 90 0.9 99 0.98 967.04 994.0 00.6 045. 900 864 0.87 895 0.9 94 0.99 95.06 980. 007.8 0.5 056. 000 88 0.95 9.0 940.08 967.4 994. 00.7 044.4 068.40 00 898.0 97.0 955.7 98. 008.0 0.7 057.4 080.50 00 96. 944.9 97.6 998. 0.40 047.47 07.54 09.60 00 94. 96.9 988.6 04.4 08.50 06.58 085.65 07.7 400 95. 979.40 005.47 00.54 054.6 077.69 099.76.8 Page
BLOWER DATA - BELT DRIVE - ZHB07 BLOWER TABLE INCLUDES RESISTANCE FOR BASE UNIT ONLY WITH DRY INDOOR COIL AND AIR FILTERS IN PLACE. FOR ALL UNITS ADD: - Any factory installed options air resistance (heat section, economizer, wet coil, etc.). - Any field installed accessories air resistance (duct resistance, diffuser, etc.). See page for blower motors and drives and wet coil and options/accessory air resistance data. DOWNFLOW Volume 0.0 0.0 0.0 0.40 0.50 0.60 0.70 0.80 800 558 0.8 589 0.4 6 0.48 658 0.54 694 0.59 70 0.64 767 0.70 80 0.75 900 578 0.44 60 0.49 64 0.54 678 0.60 74 0.65 749 0.70 785 0.76 89 0.8 000 600 0.50 6 0.56 665 0.6 699 0.66 74 0.7 769 0.77 80 0.8 87 0.90 00 6 0.57 655 0.6 688 0.68 7 0.7 755 0.79 789 0.84 8 0.9 854 0.98 00 647 0.65 678 0.70 7 0.75 74 0.8 776 0.86 809 0.9 84.00 87.06 00 67 0.7 70 0.78 74 0.8 766 0.89 798 0.95 89.0 860.09 890.6 400 696 0.8 76 0.87 757 0.9 788 0.98 89.04 850. 880.9 909.6 500 70 0.90 750 0.95 780.0 8.07 84.4 87. 900.0 99.7 600 745 0.99 774.05 804. 84.7 864.5 89. 9.4 949.49 700 770.09 799.5 88. 858.8 887.6 96.44 94.5 969.6 800 795.9 84.5 85. 88.40 9.48 99.56 965.65 990.7 900 80.0 849.7 878.45 907.5 95.6 96.70 988.78 0.86 Volume 0.90.00.0.0.0.40.50.60 800 88 0.8 870 0.87 90 0.9 9 0.98 958.04 984.0 009.6 04. 900 85 0.88 885 0.94 95 0.99 944.05 97. 996.7 0. 045.9 000 869 0.96 899.0 99.07 957. 984.9 009.5 0. 058.8 00 885.04 95.0 944.5 97. 997.8 0.4 046.40 070.46 00 90. 9.9 959.4 986. 0.7 06.4 060.50 084.56 00 90. 948.9 975.5 00.4 07.47 05.5 075.60 098.66 400 98. 965.9 99.45 07.5 04.58 066.64 090.70.77 500 956.44 98.5 009.57 04.6 059.69 08.75 05.8 8.88 600 975.56 00.6 06.69 05.75 075.8 098.87.9 4.00 700 995.68 00.75 044.8 069.87 09.9 4.99 6.06 58. 800 05.8 09.87 06.94 086.00 09.06. 5.9 74.6 900 05.94 058.00 08.07 04. 6.9 47.6 68. 89.40 HORIZONTAL Volume 0.0 0.0 0.0 0.40 0.50 0.60 0.70 0.80 800 56 0.9 597 0.44 65 0.49 67 0.5 70 0.58 746 0.6 78 0.68 86 0.7 900 58 0.44 68 0.49 655 0.54 69 0.59 79 0.64 765 0.69 800 0.75 8 0.80 000 60 0.50 69 0.55 676 0.6 7 0.66 749 0.7 784 0.76 88 0.8 850 0.88 00 65 0.57 66 0.6 698 0.67 75 0.7 770 0.78 804 0.84 87 0.90 868 0.96 00 648 0.64 685 0.69 7 0.75 757 0.80 79 0.86 84 0.9 856 0.98 886.05 00 67 0.7 709 0.77 745 0.8 780 0.88 8 0.94 845.0 876.08 905.5 400 699 0.79 74 0.85 769 0.9 80 0.97 85.04 866. 896.8 94.5 500 75 0.88 759 0.94 79.00 86.07 857.4 887. 96.8 944.6 600 75 0.97 785.04 88.0 850.7 880.5 909. 97.40 964.48 700 779.07 8.4 84. 87.9 90.7 9.44 958.5 984.60 800 805.8 87.6 868. 897.4 95.49 95.57 979.66 004.74 900 8.0 86.8 89.46 9.54 948.6 974.7 000.80 04.88 Volume 0.90.00.0.0.0.40.50.60 800 848 0.79 880 0.85 90 0.9 99 0.98 967.04 994.0 00.6 045. 900 864 0.87 895 0.9 94 0.99 95.06 980. 007.8 0.5 056. 000 88 0.95 9.0 940.08 967.4 994. 00.7 044.4 068.40 00 898.0 97.0 955.7 98. 008.0 0.7 057.4 080.50 00 96. 944.9 97.6 998. 0.40 047.47 07.54 09.60 00 94. 96.9 988.6 04.4 08.50 06.58 085.65 07.7 400 95. 979.40 005.47 00.54 054.6 077.69 099.76.8 500 97.4 997.5 0.59 046.66 069.74 09.8 4.88 5.95 600 990.55 05.6 09.7 06.79 086.86 08.94 9.0 50.07 700 009.68 04.76 057.84 080.9 0.99 4.07 45.4 66. 800 08.8 05.9 075.98 097.06 9. 40. 6.8 8.4 900 048.96 07.04 09. 5 Page.0 6.8 57.5 77.4 98.48
BLOWER DATA DRIVE KIT SPECIFICATIONS - ZHA06-060, ZHB06-048 Model No. ZHA/ZHB 06 Motor HP No. of Drive Kits and RPM Range Nominal Maximum Speeds ZA0 ZA0 ZA0 ZA04 ZA05 ZA06 0.75 0.86 678-05 - - - - - - 964-47 - - - - - -.5 678-05 - - - - - - 964-47 - - - - - -.5.7 678-05 - - - - - - 964-47 - - - - - - ZHA/ZHB 048 0.75 0.86 - - - 80-6 - - - - - - - - - - - -.5 - - - 80-6 - - - - - - - - - - - -.5.7 - - - 80-6 - - - - - - 098-490 - - - ZHA060.5 - - - - - - 906-8 - - - - - - - - -.5.7 - - - - - - 906-8 - - - - - - 6-64 DRIVE KIT SPECIFICATIONS - ZHB060-07 Model Motor HP No. of Drive Kits and RPM Range No. Nominal Maximum Speeds ZAA0 ZAA0 ZAA0 4 ZAA04 ZHB060 0.75 0.86 5-784 6-875 - - - - - -.5 5-784 6-875 - - - - - -.5.7 5-784 6-875 798-05 - - - ZHB07.5 - - - 6-875 - - - - - -.5.7 - - - 6-875 798-05 - - -. - - - 6-875 798-05 9-8 NOTE - Using total air volume and system static pressure requirements determine from blower performance tables rpm and motor hp required. Maximum usable hp of motors furnished are shown. In Canada, nominal motor hp is also maximum usable motor hp. If motors of comparable hp are used, be sure to keep within the service factor limitations outlined on the motor nameplate. 0.75 and.5 hp motors are only available for ZHB06-060 08/0V-ph applications. hp blower motor is not available for ZHB060 08/0V-ph applications..5 hp blower motor is the minimum required with the ZA05, ZA06, and ZAA0 drive kits. 4 hp blower motor is required with the ZAA04 drive kit. POWER EXHAUST FAN PERFORMANCE Return System Static Pressure - in. w.g. Volume Exhausted 0.00 865 0.05 785 0.0 70 0.5 60 0.0 545 0.5 450 0.0 50 0.5 40 Page
BLOWER DATA OPTIONS / ACCESSORIES AIR RESISTANCE - in. w.g. Volume ZHA06, ZHA048 ZHA060, ZHB06 Wet Indoor Coil ZHB048, ZHB060 Economizer Electric ZHB07 Heat Downflow Horizontal 900 0.0 0.0 - - - - - - 0.05 0.0 0.04 000 0.0 0.0 - - - - - - 0.06 0.0 0.05 00 0.0 0.0 - - - - - - 0.08 0.04 0.05 00 0.0 0.0 0.0 - - - 0.09 0.05 0.06 00 0.0 0.0 0.0 - - - 0. 0.05 0.07 400 0.0 0.0 0.0 - - - 0.7 0.06 0.08 500 0.04 0.0 0.0 - - - 0. 0.07 0.08 600 0.04 0.0 0.0 0.0 0.6 0.08 0.09 700 0.05 0.04 0.0 0.0 0.0 0.09 0.0 800 0.05 0.04 0.0 0.0 0. 0.0 0. 900 0.06 0.05 0.04 0.04 0. 0. 0. 000 0.06 0.05 0.04 0.04 0. 0. 0. 00 - - - 0.06 0.05 0.05 0.7 0. 0.4 00 - - - 0.06 0.05 0.05 0.9 0.4 0.5 00 - - - 0.07 0.05 0.05 0. 0.5 0.6 400 - - - 0.07 0.06 0.06 0. 0.6 0.8 500 - - - - - - - - - 0.06 0.4 0.8 0.9 600 - - - - - - - - - 0.07 0.8 0.9 0.0 700 - - - - - - - - - 0.07 0.4 0.0 0. 800 - - - - - - - - - 0.07 0.45 0. 0. 900 - - - - - - - - - 0.08 0.49 0. 0.4 Page 4
BLOWER DATA CEILING DIFFUSERS AIR RESISTANCE (in. w.g.) Volume Ends Open RTD9-65S Step Down Diffuser Side & Ends Open All Ends & Sides Open FD9-65S Flush Diffuser Ends Open RTD-95S Step Down Diffuser Side & Ends Open All Ends & Sides Open FD-95S Flush Diffuser 800 0.5 0. 0. 0. - - - - - - - - - - - - 000 0.9 0.6 0.4 0.4 - - - - - - - - - - - - 00 0.5 0.0 0.7 0.7 - - - - - - - - - - - - 400 0. 0.6 0.0 0.0 - - - - - - - - - - - - 600 0.4 0. 0.0 0.4 - - - - - - - - - - - - 800 0.56 0.40 0.0 0.0 0. 0. 0.09 0.09 000 0.7 0.50 0.6 0.6 0.5 0. 0. 0.0 00 0.95 0.6 0.44 0.44 0.8 0.5 0. 0. 400 - - - - - - - - - - - - - 0. 0.8 0.5 0.4 600 - - - - - - - - - - - - - 0.4 0. 0.8 0.7 800 - - - - - - - - - - - - - 0.7 0.4 0. 0.0 000 - - - - - - - - - - - - - 0. 0.9 0.5 0.5 00 - - - - - - - - - - - - - 0.4 0.7 0. 0. 400 - - - - - - - - - - - - - 0.50 0.45 0.9 0.7 600 - - - - - - - - - - - - - 0.6 0.54 0.48 0.44 CEILING DIFFUSER AIR THROW DATA Volume - Effective Throw - ft. Model No. RTD9-65S FD9-65S 800 0-7 4-8 000 0-7 5-0 00-8 6-400 - 9 7-4 600-0 8-5 800-0 - 8 000 4 - - 9 00 6-5 - 0 Model No. RTD-95S FD-95S 600 4-9 9-4 800 5-0 0-8 000 7 - - 9 00 8-5 - 9 400 0-7 - 0 600 5 - - 4 Effective throw based on terminal velocities of 75 ft. per minute. Page 5
ELECTRICAL/ELECTRIC HEAT DATA - ZHA TON ZHA06S4 Voltage - 60hz 08/0V - Ph 460V - Ph 575V - Ph Compressor Rated Load Amps 8.7 4.6 Locked Rotor Amps 70 7 Outdoor Fan Motor () 0.5 HP Indoor Blower Motor Maximum Overcurrent Protection Full Load Amps.7 0.9 0.7 Full Load Amps.5 0.6 0.6 Horsepower.5.5.5 Full Load Amps 4.6 6.6..7.4 Unit Only 5 5 5 5 5 5 With () 0.5 HP 5 5 5 5 5 5 Minimum Circuit Ampacity Unit Only 8 0 8 9 7 8 With () 0.5 HP 9 9 0 8 9 ELECTRIC HEAT DATA Voltage 08V 40V 08V 40V 480V 480V 600V 600V Maximum Overcurrent Protection Minimum Circuit Ampacity Maximum Overcurrent Protection Minimum Circuit Ampacity Unit+ Unit+ Unit+ and () 0.5 HP Unit+ and () 0.5 HP 5 kw 5 5 5 5 0 0 5 5 7.5 kw 40 40 40 45 0 5 0 0 0 kw 45 50 50 50 5 5 0 0 5 kw 60 70 60 70 5 5 5 0 5 kw 5 6 7 4 7.5 kw 7 40 9 4 0 6 7 0 kw 44 48 46 50 4 4 9 0 5 kw 57 6 59 65 5 6 5 kw 5 5 5 40 0 0 5 5 7.5 kw 40 45 45 45 0 5 0 0 0 kw 45 50 50 60 5 5 0 5 5 kw 60 70 60 70 5 5 0 0 5 kw 4 4 6 7 8 4 5 7.5 kw 9 4 4 44 0 7 8 0 kw 45 49 47 5 4 5 0 5 kw 58 64 60 66 6 7 ELECTRIC HEAT ACCESSORIES Unit Fuse Block Unit Only 0A7 0A7 0A9 0A9 Unit + 0A7 0A7 0A9 0A9 NOTE - All units have a minimum Short Circuit Current Rating (SCCR) of 5000 amps. Extremes of operating range are plus and minus 0% of line voltage. HACR type breaker or fuse. Refer to National or Canadian Electrical Code manual to determine wire, fuse and disconnect size requirements. Page 6
ELECTRICAL/ELECTRIC HEAT DATA - ZHA ZHA048S4 4 TON Voltage - 60hz 08/0V - Ph 460V - Ph 575V - Ph Compressor Rated Load Amps 5.5 4.7 Locked Rotor Amps 86 7 4 Outdoor Fan Motor () 0.5 HP Indoor Blower Motor Maximum Overcurrent Protection Full Load Amps.7 0.9 0.7 Full Load Amps.5 0.6 0.6 Horsepower.5.5.5 Full Load Amps 4.6 6.6..7.4 Unit Only 0 0 5 5 5 5 With () 0.5 HP 0 0 5 5 5 5 Minimum Circuit Ampacity Unit Only 0 9 9 With () 0.5 HP 4 9 0 ELECTRIC HEAT DATA Voltage 08V 40V 08V 40V 480V 480V 600V 600V Maximum Overcurrent Protection Minimum Circuit Ampacity Maximum Overcurrent Protection Minimum Circuit Ampacity Unit+ Unit+ Unit+ and () 0.5 HP Unit+ and () 0.5 HP 5 kw 40 40 40 45 0 0 5 5 7.5 kw 45 45 45 50 5 5 0 0 0 kw 50 60 50 60 5 0 5 5 5 kw 60 70 70 70 5 5 0 0.5 kw 80 90 90 90 45 45 40 40 5 kw 4 6 6 8 8 9 5 5 7.5 kw 40 4 4 45 8 8 0 kw 47 5 49 5 5 6 5 kw 60 66 6 68 4 7 8.5 kw 79 88 8 90 44 45 6 7 5 kw 40 40 40 45 0 0 5 0 7.5 kw 45 50 50 50 5 5 0 0 0 kw 50 60 50 60 0 0 5 5 5 kw 70 70 70 70 5 5 0 0 90 90 90 00 45 50 40 40 5 kw 5 7 7 9 8 9 5 6 7.5 kw 4 45 44 47 8 9 0 kw 48 5 50 54 6 7 5 kw 6 67 6 69 4 4 7 8.5 kw 8 90 8 9 45 46 6 7 ELECTRIC HEAT ACCESSORIES Unit Fuse Block Unit Only 0A7 0A7 0A9 0A9 Unit + 0A7 0A7 0A9 0A9 NOTE - All units have a minimum Short Circuit Current Rating (SCCR) of 5000 amps. Extremes of operating range are plus and minus 0% of line voltage. HACR type breaker or fuse. Refer to National or Canadian Electrical Code manual to determine wire, fuse and disconnect size requirements. Page 7
ELECTRICAL/ELECTRIC HEAT DATA - ZHA ZHA060S4 5 TON Voltage - 60hz 08/0V - Ph 460V - Ph 575V - Ph Compressor Rated Load Amps.5 8 5 Locked Rotor Amps 09 59 40 Outdoor Fan Motor () 0.5 HP Indoor Blower Motor Maximum Overcurrent Protection Full Load Amps.7 0.9 Full Load Amps.5 0.6 0.6 Horsepower.5.5.5 Full Load Amps 4.6 6.6..7.4 Unit Only 5 5 0 0 5 5 With () 0.5 HP 5 40 0 0 5 5 Minimum Circuit Ampacity Unit Only 4 6 4 4 9 0 With () 0.5 HP 5 7 4 5 0 ELECTRIC HEAT DATA Voltage 08V 40V 08V 40V 480V 480V 600V 600V Maximum Overcurrent Protection Minimum Circuit Ampacity Maximum Overcurrent Protection Minimum Circuit Ampacity Unit+ Unit+ Unit+ and () 0.5 HP Unit+ and () 0.5 HP 5 kw 45 45 45 50 5 5 5 0 7.5 kw 50 50 50 50 0 0 0 0 0 kw 50 60 60 60 0 0 5 5 5 kw 70 70 70 80 40 40 0 0.5 kw 90 00 90 00 50 50 40 40 5 kw 7 9 9 4 5 6 7.5 kw 4 46 45 48 5 6 8 9 0 kw 50 54 5 56 9 0 5 kw 6 69 65 7 6 7 7 8.5 kw 8 9 84 9 47 48 6 7 5 kw 45 50 50 50 5 5 0 0 7.5 kw 50 50 50 50 0 0 0 0 0 kw 60 60 60 60 0 0 5 5 5 kw 70 70 70 80 40 40 0 0 90 00 90 00 50 50 40 40 5 kw 8 40 40 4 6 7 7.5 kw 45 48 47 50 5 6 9 0 0 kw 5 55 5 57 9 0 5 kw 64 70 66 7 7 8 8 9.5 kw 84 9 86 95 48 49 7 8 ELECTRIC HEAT ACCESSORIES Unit Fuse Block Unit Only 0A8 0A8 0A9 0A9 Unit + 0A8 0A8 0A9 0A9 NOTE - All units have a minimum Short Circuit Current Rating (SCCR) of 5000 amps. Extremes of operating range are plus and minus 0% of line voltage. HACR type breaker or fuse. Refer to National or Canadian Electrical Code manual to determine wire, fuse and disconnect size requirements. Page 8
ELECTRICAL/ELECTRIC HEAT DATA - ZHB TON ZHB06S4 Voltage - 60hz 08/0V - Ph 08/0V - Ph 460V - Ph 575V - Ph Compressor Rated Load Amps 5. 8.7 4.6 Locked Rotor Amps 70 70 7 Outdoor Fan Motor () 0.5 HP Indoor Blower Motor Maximum Overcurrent Protection Full Load Amps 0.6 0.45 Full Load Amps.5.5 0.6 0.6 Horsepower 0.75.5.5.5.5 Full Load Amps 7.6 4.6 6.6..7.4 Unit Only 40 45 5 5 5 5 5 5 With () 0.5 HP 40 45 5 5 5 5 5 5 Minimum Circuit Ampacity Unit Only 8 7 9 8 9 7 8 With () 0.5 HP 0 8 0 9 0 8 8 ELECTRIC HEAT DATA Voltage 08 40 08 40 40 40 480 480 600 600 Maximum Overcurrent Protection Minimum Circuit Ampacity Maximum Overcurrent Protection Minimum Circuit Ampacity Unit+ Unit+ Unit+ and () 0.5 HP Unit+ and () 0.5 HP 5 kw 60 60 60 60 5 5 5 0 5 5 7.5 kw 70 70 70 80 40 45 0 0 0 0 0 kw 80 80 80 90 50 50 5 5 0 0 5 kw 00 0 00 0 70 70 0 5 5 0 5 kw 5 54 54 58 4 5 7 4 7.5 kw 6 67 65 7 40 4 9 0 6 7 0 kw 7 80 77 84 47 49 4 9 0 5 kw 96 06 99 0 6 64 0 5 6 5 kw 60 60 60 60 5 40 0 0 5 5 7.5 kw 70 70 70 80 45 45 0 5 0 0 0 kw 80 90 80 90 50 60 5 5 0 0 5 kw 00 0 0 5 70 70 5 5 5 0 5 kw 5 56 56 59 4 6 6 7 4 7.5 kw 64 69 67 7 4 4 0 6 7 0 kw 75 8 78 85 49 5 5 9 0 5 kw 97 08 0 64 66 5 6 ELECTRIC HEAT ACCESSORIES Unit Fuse Block Unit Only 0A6 0A6 0A7 0A9 0A9 Unit + 0A6 0A6 0A7 0A9 0A9 NOTE - All units have a minimum Short Circuit Current Rating (SCCR) of 5000 amps. Extremes of operating range are plus and minus 0% of line voltage. HACR type breaker or fuse. Refer to National or Canadian Electrical Code manual to determine wire, fuse and disconnect size requirements. Page 9
ELECTRICAL/ELECTRIC HEAT DATA - ZHB ZHB048S4 4 TON Voltage - 60hz 08/0V - Ph 08/0V - Ph 460V - Ph 575V - Ph Compressor Rated Load Amps 0 5.5 4.7 Locked Rotor Amps 99 86 7 4 Outdoor Fan Motor () 0.5 HP Indoor Blower Motor Maximum Overcurrent Protection Full Load Amps.7.7 0.9 0.7 Full Load Amps.5.5 0.6 0.6 Horsepower 0.75.5.5.5.5 Full Load Amps 7.6 4.6 6.6..7.4 Unit Only 50 50 0 0 5 5 5 5 With () 0.5 HP 50 50 0 0 5 5 5 5 Minimum Circuit Ampacity Unit Only 5 8 0 9 9 With () 0.5 HP 6 40 4 9 0 ELECTRIC HEAT DATA Voltage 08 40 08 40 08 40 08 40 480 480 600 600 Maximum Overcurrent Protection Unit+ 5 kw 70 70 70 70 40 40 40 45 0 0 5 5 7.5 kw 80 80 80 80 45 45 45 50 5 5 0 0 0 kw 90 90 90 90 50 60 50 60 5 0 5 5 5 kw 0 5 0 5 60 70 70 70 5 5 0 0 kw 50 75 50 75 80 90 90 90 45 45 40 40 Minimum Circuit Ampacity Unit+ 5 kw 57 6 6 64 4 6 6 8 8 9 5 5 7.5 kw 69 74 7 77 40 4 4 45 8 8 0 kw 80 87 8 90 47 5 49 5 5 6 5 kw 0 06 6 60 66 6 68 4 7 8 kw 6 5 40 55 79 88 8 90 44 45 6 7 Maximum Overcurrent Protection Unit+ and () 0.5 HP 5 kw 70 70 70 80 40 40 40 45 0 0 5 0 7.5 kw 80 80 80 90 45 50 50 50 5 5 0 0 0 kw 90 90 90 00 50 60 50 60 0 0 5 5 5 kw 0 5 0 5 70 70 70 70 5 5 0 0 kw 50 75 50 75 90 90 90 00 45 50 40 40 Minimum Circuit Ampacity Unit+ and () 0.5 HP 5 kw 59 6 6 66 5 7 7 9 8 9 5 6 7.5 kw 70 75 74 79 4 45 44 47 8 9 0 kw 8 88 85 9 48 5 50 54 6 7 5 kw 04 4 07 8 6 67 6 69 4 4 7 8 kw 8 5 4 57 8 90 8 9 45 46 6 7 ELECTRIC HEAT ACCESSORIES Unit Fuse Block Unit Only 0A6 0A6 0A7 0A7 0A9 0A9 Unit + 0A6 0A6 0A7 0A7 0A9 0A9 NOTE - All units have a minimum Short Circuit Current Rating (SCCR) of 5000 amps. Extremes of operating range are plus and minus 0% of line voltage. HACR type breaker or fuse. Refer to National or Canadian Electrical Code manual to determine wire, fuse and disconnect size requirements. Page 0
ELECTRICAL/ELECTRIC HEAT DATA - ZHB ZHB060S4 5 TON Voltage - 60hz 08/0V - Ph 08/0V - Ph 460V - Ph 575V - Ph Compressor Rated Load Amps..5 8 5 Locked Rotor Amps 5 09 59 40 Outdoor Fan Motor () 0.5 HP Indoor Blower Motor Maximum Overcurrent Protection Full Load Amps.7.7 0.9 Full Load Amps.5.5 0.6 0.6 Horsepower 0.75.5.5.5.5 Full Load Amps 7.6 4.6 6.6..7.4 Unit Only 50 60 5 5 0 0 5 5 With () 0.5 HP 60 60 5 40 0 0 5 5 Minimum Circuit Ampacity Unit Only 7 4 4 6 4 4 9 0 With () 0.5 HP 9 4 5 7 4 5 0 ELECTRIC HEAT DATA Voltage 08 40 08 40 08 40 08 40 480 480 600 600 Maximum Overcurrent Protection Unit+ 5 kw 70 70 80 80 45 45 45 50 5 5 5 0 7.5 kw 80 90 80 90 50 50 50 50 5 0 0 0 0 kw 90 00 90 00 50 60 60 60 0 0 5 5 5 kw 0 5 0 5 70 70 70 80 40 40 0 0 kw 50 75 50 75 90 90 90 00 50 50 40 40 Minimum Circuit Ampacity Unit+ 5 kw 60 6 6 67 6 8 9 4 5 6 7.5 kw 7 76 75 80 4 45 45 48 4 6 8 9 0 kw 8 90 86 9 49 5 5 56 8 0 5 kw 05 6 09 9 6 68 65 7 6 7 7 8 kw 9 55 4 58 8 90 84 9 47 48 6 7 Maximum Overcurrent Protection Unit+ and () 0.5 HP 5 kw 70 80 80 80 45 45 50 50 5 5 0 0 7.5 kw 80 90 90 90 50 50 50 50 0 0 0 0 0 kw 90 00 00 00 50 60 60 60 0 0 5 5 5 kw 0 5 0 5 70 70 70 80 40 40 0 0 kw 50 75 50 75 90 00 90 00 50 50 40 40 Minimum Circuit Ampacity Unit+ and () 0.5 HP 5 kw 6 65 65 68 7 9 40 4 6 7 7.5 kw 7 78 76 8 44 47 47 50 5 6 9 0 0 kw 84 9 87 94 50 54 5 57 9 0 5 kw 07 7 0 0 6 69 66 7 6 8 8 9 kw 40 56 44 60 8 9 86 95 48 49 7 8 ELECTRIC HEAT ACCESSORIES Unit Fuse Block Unit Only 0A6 0A6 0A8 0A8 0A9 0A9 Unit + 0A6 0A6 0A8 0A8 0A9 0A9 NOTE - All units have a minimum Short Circuit Current Rating (SCCR) of 5000 amps. Extremes of operating range are plus and minus 0% of line voltage. HACR type breaker or fuse. Refer to National or Canadian Electrical Code manual to determine wire, fuse and disconnect size requirements. Page
ELECTRICAL/ELECTRIC HEAT DATA ZHB07S4 Voltage - 60hz 08/0V - Ph 460V - Ph 575V - Ph Compressor Rated Load Amps.4 0.6 7.7 Outdoor Fan Motor () 0.5 HP Indoor Blower Motor Locked Rotor Amps 49 75 54 Full Load Amps.4. Full Load Amps.5 0.6 0.6 6 TON Horsepower.5.5.5 Full Load Amps 4.6 6.6 7.5..4.7.4.7 Maximum Unit Only 50 50 60 5 5 5 0 0 0 Overcurrent With () 0.5 HP Protection 50 60 60 5 5 5 0 0 0 Minimum Unit Only 5 7 8 7 8 8 4 4 Circuit With () 0.5 HP Ampacity 7 9 40 8 9 9 4 4 ELECTRIC HEAT DATA Voltage 08 40 08 40 08 40 480 480 480 600 600 600 Maximum Unit+ 7.5 kw 70 70 70 70 70 70 5 5 5 5 5 5 Overcurrent 0 kw 70 80 80 80 80 80 5 40 40 5 0 0 Protection 5 kw 80 90 90 90 90 90 45 45 45 5 5 5 kw 00 0 00 0 00 0 60 60 60 40 45 45 0 kw 5 50 5 50 5 50 70 70 70 50 50 50 Minimum Unit+ 7.5 kw 55 58 57 60 58 6 8 9 0 Circuit 0 kw 6 66 64 68 64 68 5 6 6 Ampacity 5 kw 75 8 77 8 77 84 40 4 4 kw 94 0 96 05 97 06 5 5 5 40 4 4 0 kw 4 6 6 8 7 9 6 6 64 49 50 50 Maximum Unit+ 7.5 kw 70 70 70 70 70 70 5 5 5 5 5 5 Overcurrent 0 kw 70 80 80 80 80 80 5 40 40 0 0 0 Protection and () 0.5 HP 5 kw 90 90 90 90 90 90 45 45 45 5 5 5 kw 00 0 00 0 00 0 60 60 60 40 45 45 0 kw 5 50 5 50 5 50 70 70 70 50 50 60 Minimum Unit+ 7.5 kw 57 60 59 6 59 6 9 0 0 Circuit 0 kw 6 67 65 69 66 70 4 4 5 6 6 Ampacity and () 0.5 HP 5 kw 76 8 78 84 79 85 40 4 4 kw 96 05 98 07 99 08 5 5 5 40 4 4 0 kw 5 7 7 9 8 0 6 64 64 50 50 5 ELECTRIC HEAT ACCESSORIES Unit Fuse Block Unit Only 0A8 0A8 0A8 0A9 0A9 Unit + 0A8 0A8 0A8 0A9 0A9 NOTE - All units have a minimum Short Circuit Current Rating (SCCR) of 5000 amps. Extremes of operating range are plus and minus 0% of line voltage. HACR type breaker or fuse. Refer to National or Canadian Electrical Code manual to determine wire, fuse and disconnect size requirements. Page
ELECTRIC HEAT CAPACITIES Input Voltage No of Stages 5 kw 7.5 kw 0 kw kw input Btuh Output No of Stages kw input Btuh Output No of Stages kw input Btuh Output 08.8,800 5.6 9,00 7.5 5,600 0 4. 4,00 6.,500 8.4 8,700 0 4.6 5,700 6.9,500 9.,400 40 5.0 7,00 7.5 5,600 0.0 4,00 440 4. 4,00 6.,500 8.4 8,700 460 4.6 5,700 6.9,500 9.,400 480 5.0 7,00 7.5 5,600 0.0 4,00 550 4. 4,00 6.,500 8.4 8,700 575 4.6 5,700 6.9,500 9.,400 600 5.0 7,00 7.5 5,600 0.0 4,00 Input Voltage No of Stages 5 kw.5 kw 0 kw kw input Btuh Output No of Stages kw input Btuh Output No of Stages kw input Btuh Output 08. 8,400 6.9 57,700.5 76,800 0.6 4,000 8.9 64,500 5. 86,000 0.8 47,000 0.7 70,700 7.5 9,900 40 5.0 5,00.5 76,800 0.0 0,400 440.6 4,000 8.9 64,500 5. 86,000 460.8 47,000 0.7 70,700 7.5 9,900 480 5.0 5,00.5 76,800 0.0 0,400 550.6 4,000 8.9 64,500 5. 86,000 575.8 47,000 0.7 70,700 7.5 9,900 600 5.0 5,00.5 76,800 0.0 0,400 Page
ZHA/ZHB PARTS ARRANGEMENT CONTROL PANEL EVAPORATOR COIL BLOWER MOTOR OUTDOOR COIL FAN COMPRESSOR BLOWER HOUSING ELECTRIC HEAT (OPTIONAL) OUTDOOR COIL SIDE POWER ENTRY BOTTOM POWER ENTRY UNIT FUSE TB UNIT TERMINAL STRIP FIGURE ZHA/ZHB CONTROL BOX LOW AMBIENT BLOWER DELAY RELAY RELAY K58 BLOWER DELAY K5 TIMER DL49 OUTDOOR FAN RELAY K0 TRANSFER RELAY K8 TRANSFORMER T DEFROST CONTROL CMC CRANKCASE HEATER TIMER DL48 CRANKCASE HEATER RELAY K9 POWER EXHAUST TRANSFORMER T0 CAPACITOR C or C FIGURE CONTACTOR K BLOWER CONTACTOR K Page 4
I-UNIT COMPONENTS The ZHA/ZHB unit components are shown in figure. All units come standard with removable unit panels. All L, L, and L wiring is color coded; L is red, L is yellow, and L is blue. A-Control Box Components ZHA/ZHB control box components are shown in figure. The control box is in the outdoor section to the left of the blower and heat section. -Control Transformer T 08/0V TRANSFORMER PINK GRAY SECONDARY 08 VOLTS 0 VOLTS PRIMARY YELLOW PINK All use a single line voltage to 4VAC transformer mounted in the control box. Transformer supplies power to control circuits in the unit. The transformer is rated at 70VA and is protected by a amp (auto) fuse F. The 08/0 (Y) voltage transformers use two primary voltage taps as shown in figure, while 460 (G) and 575 (J) voltage transformers use a single primary voltage tap. FIGURE -Fan Capacitor C (three phase) Fan capacitor C is used to assist in the start up of condenser fan B4. Ratings will be on side of capacitor or outdoor fan motor nameplate. -Dual Capacitor C (single phase) A single dual capacitor is used for both the outdoor fan and compressor (see unit diagram). The fan side and the compressor side have different MFD ratings. See side of capacitor for ratings. 4-Compressor Contactor K In all ZHA/ZHB units, K energizes compressors B in response to thermostat demand. Three phase units use two pole double break contactors with a 4 volt coil. Single phase units use single pole double break contactors with a 4 volt coil. 5-Blower Contactor K On three phase units, K is a two pole double break contactor with a 4VAC coil and on single phase units is a single pole double break contactor with a 4 volt coil. K energizes the indoor blower motor B in response to blower demand. 6-Transfer Relay K8 K8 is a two-pole relay with a 4V coil used to de-energize the reversing valve and energize the blower during a heat call. On a first stage heat call, K8- N.O. terminals close to energize blower contactor K. At the same time K8- N.C. terminals open to interrupt the signal at CMC terminal O. This enables CMC to de-energize the reversing valve for heating mode. Without K8 the reversing valve would remain energized at all times. 7-Condenser Fan Relay K0 (G, J voltage) Outdoor fan relay K0 is a DPDT relay with a 4VAC coil. K0 relay coil is in series with CMC fan contacts and energizes B4 outdoor fan via K0- n.o. contacts. 8-Crankcase Heater Delay DL48 & Crankcase Heater Relay K9 Delay DL48 and relay K9 keep the crankcase heater deenergized during and immediately following compressor shut down. They ensure the crankcase heater is off while the compressor is energized. DL48 and K9 are used together on ZHB06,-048 and -060 units. K9 is used without DL48 on ZHB07. 9-Blower Delay DL49 & Blower Relay K5 Delay DL49 and relay K5 keep the blower energized for 0 seconds immediately following compressor shut down after heating or cooling demand. 0-Exhaust Fan Transformer T0 (J voltage) Transformer T0 is a field-installed 600/0V transformer which provides power to the 08/0V power exhaust fan in 575V applications. Page 5
-Defrost Control CMC The defrost thermostat and the defrost control work together to ensure that the heat pump outdoor coil does not ice excessively during the heating mode. Compressor Accumulated Run-Time Interval The defrost control will not energize a defrost cycle unless the unit has been operating in heating mode for an accumulated 90 minutes (default). The run time interval can be changed by moving the jumper on the CMC board timing pins. See figure 4. DEFROST CONTROL BOARD CMC TIMING JUMPER 90 MINUTES DIAGNOSTIC LEDS REMOVED AT THE FACTORY TO DISABLE COMPRESSOR DELAY or 4 minutes have passed. If the jumper is not removed until after the additional 5-second period has elapsed, the defrost will terminate and the test option will not function again until the jumper is removed and re-applied. Diagnostic LEDs The defrost board uses two LEDs for diagnostics. The LEDs flash a sequence according to the condition. TABLE Defrost Control Board Diagnostic LED Mode Green LED (DS) Red LED (DS) No power to control OFF OFF Normal operation / Simultaneous Slow FLASH power to control Anti short cycle lockout Alternating Slow FLASH High pressure switch Slow FLASH OFF fault High pressure switch lockout ON OFF -Compressor B IMPORTANT The Clean Act of 990 bans the intentional venting of refrigerant (CFC's and HCFC's) as of July, 99. Approved methods of recovery, recycling or reclaiming must be followed. Fines and/or incarceration may be levied for non-compliance. All units use one scroll compressor. See SPECIFI CATIONS and ELECTRICAL DATA (table of contents) or compressor nameplate for compressor specifications. WARNING FIGURE 4 The defrost interval can be adjusted to 0, 60, or 90 minutes. The defrost timing jumper is factory-installed to provide a 90-minute defrost interval. If the timing selector jumper is not in place, the control defaults to a 90-minute defrost interval. Defrost Test Option A TEST option is provided for troubleshooting. The TEST mode may be started any time the unit is in the heating mode and the defrost thermostat is closed or jumpered. If the timing jumper is in the TEST position at power up, the defrost control will ignore the test pins. When the jumper is placed across the TEST pins for two seconds, the control will enter the defrost mode. If the jumper is removed before an additional 5-second period has elapsed (7 seconds total), the unit will remain in defrost mode until the defrost switch opens Electrical shock hazard. Compressor must be grounded. Do not operate without protective cover over terminals. onnect power before removing protective cover. harge capacitors before servicing unit. Failure to follow these precautions could cause electrical shock resulting in injury or death. The compressor is energized by a compressor contactor. NOTE-Refer to the wiring diagram section for specific unit operation. If Interlink compressor replacement is necessary, call -800-45-6669. IMPORTANT Some scroll compressors have an internal vacuum protector that will unload scrolls when suction pressure goes below 0 psig. A hissing sound will be heard when the compressor is running unloaded. Protector will reset when low pressure in system rises above 40 psig. DO NOT REPLACE COMPRESSOR. Page 6
-High Pressure Switch S4 The high pressure switch is an automatic reset SPST N.C. switch which opens on a pressure rise. S4 is located in the compressor discharge line and wired in series with the S5 high temperature limit and HI PS contacts on CMC defrost control board. When discharge pressure rises to 640 ± 0 psig (44 ± 69 kpa) (indicating a problem in the system) the switch opens and the compressor is de-energized (the economizer can continue to operate). When discharge pressure drops to 475 ± 0 (75 ± 8 kpa) psig, the switch closes and the compressor is energized. The CMC board monitors the pressure switch when the compressor demand Y is active, allowing five strike lockout. The compressor is shut down indefinitely in this condition. A pressure switch may open and close again four times during a current demand cycle without causing a lockout condition by resetting the count at the end of the demand cycle (CMC Y input OFF). The five-strike lockout can only be reset by one of the following actions: ZHA/ZHB PLUMBING -Power cycle the controller -Apply the TEST mode 4-Low Ambient Switches S (field-installed option) The low ambient switch is an auto reset SPST N.O. pressure switch which allows for mechanical cooling operation at low outdoor temperatures. The switch is located in the liquid line in the compressor section. On P and Y volt units, S is wired in series with the common (black) lead to B4 outdoor fan motor. On G and J volt units, S is wired in series with outdoor fan relay K0 coil and when opened breaks 4 volts to the coil, de-energizing outdoor fan B4. When liquid pressure rises to 450 ± 0 psig (0 ± 69 kpa), the switch closes and the condenser fan is energized. When liquid pressure drops to 40 ± 0 psig (655 ± 69 kpa), the switch opens and the condenser fan is de-energized. This intermittent fan operation results in higher evaporating temperature allowing the system to operate without icing the evaporator coil and losing capacity. REVERSING VALVE S4 HIGH PRESSURE LIMIT FIXED ORIFICE REFRIGERANT METERING DEVICE (RFC) DRIER LIQUID PRESSURE TAP EVAPORATOR COIL DISCHARGE PRESSURE TAP SUCTION PRESSURE TAP COMPRESSOR FIGURE 5 Page 7
5-Low Ambient Kit Relay K58 (option used with S low ambient switch) Low ambient relay K58 is a N.C. SPDT relay with a 4V coil wired in parallel with reversing valve L. When L is energized in the cooling cycle, K58 is also energized opening K58-. Therefore, K58- is always closed during heating demand bypassing S. This allows the fan to operate during the heating demand and cycle during the cooling demand. 6-Compressor Low harge Temperature Limit S (field-supplied option) S is a thermostat which opens on temperature drop. It is wired in line with K8- N.C. contacts to CMC defrost control. 7-Compressor High Temperature Limit S5 The compressor thermal protector is located on top of the compressor. S5 is wired in series with S4 high pressure limit. The protector opens at 48 F + 9 F (0 C + 5 C) and closes at 69 F + 8 F (76 C + 0 C). Refer to -High Pressure Switch S4 for five strike lockout feature. B-Blower Compartment All units are equipped with belt drive blowers. See unit nameplate for blower type. -Blower Wheels All ZHA units and ZHB 06 and 048 units use 0 x 0 (54 mm x 54 mm) blower wheels. The ZHB060 and 07 use a 5 x 9 blower wheel.(8 mm x 8 mm) -Indoor Blower Motor B Belt drive units use single or three phase motors (same as supply voltage). CFM adjustments are made by adjusting the motor pulley (sheave). Motors are equipped with sealed ball bearings. All motor specifications are listed in the Specifications (see table of contents) section in the front of this manual. Units may be equipped with motors manufactured by various manufacturers, therefore electrical FLA and LRA specifications will vary. See unit rating plate for information specific to your unit. IMPORTANT Three phase scroll compressors must be phased sequentially for correct compressor and blower rotation. Follow COOLING START-UP section of installation instructions to ensure proper compressor and blower operation. A-Blower Operation Initiate blower demand at thermostat according to instructions provided with thermostat. Unit will cycle on thermostat demand. The following steps apply to applications using a typical electro-mechanical thermostat. - Blower operation is manually set at the thermostat subbase fan switch. With fan switch in ON position, blowers will operate continuously. - With fan switch in AUTO position, the blowers will cycle with demand. Blowers and entire unit will be off when system switch is in OFF position. B-Determining Unit CFM - The following measurements must be made with air filters in place and no cooling demand. - With all access panels in place, measure static pressure external to unit (from supply to return). Blower performance data is based on static pressure readings taken in locations shown in figure 6. Note - Static pressure readings can vary if not taken where shown. Measure the indoor blower wheel RPM. - Referring to the blower tables starting on Page 6, use static pressure and RPM readings to determine unit CFM. Use air resistance table when installing units with any of the options or accessories listed. 4- The blower RPM can be adjusted at the motor pulley. Loosen Allen screw and turn adjustable pulley clockwise to increase CFM. Turn counterclockwise to decrease CFM. See figure 7. Do not exceed minimum and maximum number of pulley turns as shown in table. TABLE MINIMUM AND MAXIMUM PULLEY ADJUSTMENT Belt Min. Turns Open Maxi. Turns Open A Section No minimum 5 Page 8
LOCATION OF STATIC PRESSURE READINGS (END OF UNIT SHOWN) INSTALLATIONS WITH DUCTWORK ROOFTOP UNIT INSTALLATIONS WITH CEILING DIFFUSERS ROOFTOP UNIT MAIN DUCT RUN SUPPLY RETURN AIR READING LOCATION FIRST BRANCH OFF OF MAIN RUN SUPPLY AIR READING LOCATION SUPPLY AIR READING LOCATION SUPPLY DIFFUSER RETURN AIR READING LOCATION FIGURE 6 BLOWER ASSEMBLY TO INCREASE BELT TENSION -Loosen four bolts securing motor base to mounting frame. -Slide the motor downward to tighten the belt. -Tighten four bolts on motor base. SIDE VIEW LOOSEN FOUR BOLTS AND SLIDE BLOWER MOTOR DOWNWARD TO TIGHTEN BELT MOTOR ALLEN SCREW PULLEY TO INCREASE CFM LOOSEN ALLEN SCREW & TURN PULLEY CLOCKWISE TO DECREASE CFM TURN PULLEY COUNTERCLOCKWISE FIGURE 7 C-Blower Belt Adjustment Maximum life and wear can be obtained from belts only if proper pulley alignment and belt tension are maintained. Tension new belts after a 4-48 hour period of operation. This will allow belt to stretch and seat grooves. Make sure blower and motor pulley are aligned as shown in figure 8. - Loosen four bolts securing motor base to mounting frame. See figure 7. - To increase belt tension - Slide blower motor downward to tighten the belt. This increases the distance between the blower motor and the blower housing. - To loosen belt tension - Slide blower motor upward to loosen the belt. This decreases the distance between the blower motor and the blower housing. 4- Tighten four bolts securing motor base to the mounting frame. MOTOR PULLEY PULLEY ALIGNMENT ALIGNED BELT NOT ALIGNED FIGURE 8 BLOWER PULLEY Page 9
D-Check Belt Tension Overtensioning belts shortens belt and bearing life. Check belt tension as follows: - Measure span length X. See figure 9. MEASURE BELT TENSION FORCE DEFLECTION /64 PER INCH OF SPAN OR.5mm PER 00mm OF SPAN FIGURE 9 - Apply perpendicular force to center of span (X) with enough pressure to deflect belt /64 for every inch of span length or.5mm per 00mm of span length. Example: Deflection distance of a 40 span would be 40/64 or 5/8. Example: Deflection distance of a 400mm span would be 6mm. - Measure belt deflection force. For a used belt, the deflection force should be 5 lbs. (5kPa). A new belt deflection force should be 7 lbs. (48kPa). A force below these values indicates an undertensioned belt. A force above these values indicates an overtensioned belt. F-Field-Furnished Blower Drives See blower data tables for field-furnished blower drives to determine BHP and RPM required. See table for drive component manufacturers numbers. G-Units With Units with electric heat (5-.5kW) can operate up to.6 w.g. maximum static pressure. See table 4 for minimum air flow. TABLE DRIVE COMPONENT MANUFACTURER'S NUMBERS DRIVE COMPONENT PART NUMBERS Drive No. Motor Pulley Blower Pulley Belts Browning OEM Browning OEM Browning OEM Z0 VP4 X 7/8 K690 AK54 X 5/8 0044 0 A40 0045 7 Z0 VP4 X 7/8 K690 AK46 X 5/8 0044 A9 0045 6 Z0 VP4 X 7/8 K690 AK4 X 5/8 0044 8 A9 0045 6 Z04 VP4 X 7/8 K690 AK9 X 5/8 0044 A8 0045 5 Z05 VP44 X 7/8 P 8 488 AK49 X 5/8 0044 6 A4 0045 8 Z06 VP50 X 7/8 5J50 AK5 X 5/8 0044 9 A4 0045 9 ZAA0 VP4 X 7/8 K69 AK69 X 7L47 AX5 H0 ZAA0 VP40 X 7/8 79J0 BK80H 00788-0 A5 0045-40 ZAA0 VP40 X 7/8 79J0 AK59 X K68 A50 0045-9 ZAA04 VP44 X 7/8 P 8 488 AK59 X K68 AX5 H0 TABLE 4 MINIMUM AIRFLOW - UNITS WITH ELECTRIC HEAT kw CFM - Downflow and Horizontal ZHB06-048 ZHB060, 07 5 960 750 7.5 960 750 0 960 750 5 960 750.5 80 750 Page 0
C-ELECTRIC HEAT COMPONENTS Electric heat match-ups are found in the ELECTRICAL DATA tables. See table of contents. All electric heat sections consist of electric heating elements exposed directly to the air stream. See figure 0. See figure for vestibule parts arrangement. -Contactors K5, K6 All contactors are double break and either single, double or three pole (see diagram) and equipped with a 4VAC coil. The coils in the K5 and K6 contactors are energized by the indoor thermostat. In all units K5 energizes the heating elements, while in the 0 and.5 kw units, K5 and K6 energize the heating elements simultaneously. -High Temperature Limits S5 (Primary) S5 is a SPST N.C. auto reset thermostat high temperature limit for the electric heat section. When S5 opens, indicating a problem in the system, contactor K5 is de energized (including K6 in 0 and.5 kw P volt units). When K5 is de energized, all stages of heat are de energized. See table 5 for S5 set points. Set points are factory set and not adjustable. -Terminal Strip TB Terminal strip TB is used for single point power installations only. TB distributes power to TB. Units with multipoint power connections will not use TB. 4-Terminal Strip TB P and Y voltage units are equipped with terminal strip TB. Electric heat line voltage connections are made to TB, which distributes power to the electric heat components and is located on the vestibule. See figure. S5 PRIMARY LIMIT ELECTRIC HEAT VESTIBULE PARTS ARRANGEMENT S0 ELECTRIC HEAT SECONDARY LIMIT S58 ELECTRIC HEAT SECONDARY LIMIT TABLE 5 S5 PRIMARY HIGH TEMPERATURE LIMIT SETPOINTS Unit kw Voltage S5 Opens F S5 Closes F 5.0, 7.5, 0.0, 5.0 P 7.5, 5.0 G 60 0 5.0, 7.5, 0.0 J.5 P 7.5, 0.0, 5.0,.5 Y 5.0, 0.0 G 70 0 5.0,.5 J 5.0 Y 40 95.5 G 80 40 ELECTRIC HEAT ELEMENTS FIGURE 0 S57 ELECTRIC HEAT SECONDARY LIMIT F4 ELECTRIC HEAT FUSE TB ELECTRIC HEAT TERMINAL STRIP K9 HEAT RELAY F ELECTRIC HEAT FUSE K5 ELECTRIC HEAT CONTACTOR K6 ELECTRIC HEAT CONTACTOR FIGURE Page
5-High Temperature Limit S0, S57, S58 (Secondary) Switches are SPST N.C. manual reset thermostats. All are wired in series with the heating elements. See wiring diagrams. When either limit opens K5 and K6 are deenergized. When the contactors are de energized, all stages of heat are de energized. The thermostat is factory-set to open at 80 F + 6 F (8 C +. C) on a temperature rise and can be manually reset when temperature falls below 60 F (7.0 C). See figure for location. On.5kW (P, G and J volt) units, S5 opens at 90 F + 6 F (88 C +. C). 6-Heating Elements HE through HE Heating elements are composed of helix wound bare nichrome wire exposed directly to the air stream. Three elements are connected in a three phase arrangement. The elements in 08/0V units are connected in a Delta arrangement. Elements in 460 and 575V units are connected in Wye arrangement. Each stage is energized independently by the corresponding contactors located on the electric heat vestibule panel. Once energized, heat transfer is instantaneous. High temperature protection is provided by primary and redundant high temperature limits and overcurrent protection is provided by fuses. 7-Fuse F and F4 Fuse F and F4 are housed in a fuse block. Each fuse is connected in series with each leg of electric heat. Figure and table 6 show the fuses used with each electric heat section. 8-Unit Fuse Block & Fuse F4 Line voltage fuses F4 provide short circuit and ground fault protection to all cooling components in the ZHA/ZHB units with electric heat. Single phase units are equipped with two fuses and three phase units are equipped with three fuses. The fuses are rated in accordance with the amperage of the cooling components. The F4 fuse block is located inside a sheet metal enclosure. II-PLACEMENT AND INSTALLATION Make sure the unit is installed in accordance with the installation instructions and all applicable codes. See accessories section for conditions requiring use of the optional roof mounting frame (ZCURB). TABLE 6 kw Voltage Fuse F Qty 5.0 P 0A - 50V 7.5 P 40A - 50V 0* P 5A - 50V 5 P 40A - 50V 4.5 P 40A - 50V 6 5.0 Y 0A - 50V 7.5 Y 5A - 50V 0 Y 5A - 50V 5 Y 50A - 50V.5 Y 40A - 50V 6 5.0 G 5A - 600V 7.5 G 5A - 600V 0 G 0A - 600V 5 G 5A - 600V.5 G 5A - 600V 5.0 J 5A - 600V 7.5 J 5A - 600V 0 J 5A - 600V 5 J 0A - 600V.5 J 0A - 600V *This heater is equipped with two F4, 0A, 50V fuses. III-START UP - OPERATION A-Preliminary and Seasonal Checks - Make sure the unit is installed in accordance with the installation instructions and applicable codes. - Inspect all electrical wiring, both field and factory installed for loose connections. Tighten as required. Refer to unit diagram located on inside of control panel. - Check to ensure that refrigerant lines are in good condition and do not rub against the cabinet or other refrigerant lines. 4- Check voltage at the disconnect switch. Voltage must be within the range listed on the nameplate. If not, consult the power company and have the voltage corrected before starting the unit. 5- Recheck voltage and amp draw with unit running. If voltage is not within range listed on unit nameplate, stop unit and consult power company. Refer to unit nameplate for maximum rated load amps. 6- Inspect and adjust blower belt (see section on Blower Compartment - Blower Belt Adjustment). Page
B-Heating Start-Up - Set thermostat or temperature control device to initiate a first-stage heating demand. - A first-stage heating demand (W) will energize compressors and the outdoor fan. Note - L reversing valve is de-energized in the heating mode. ZH Units With Optional - An increased heating demand (W) will energize electric heat. Electric heat is also energized during the defrost cycle (W) to maintain discharge air temperature. C-Cooling Start-Up - Set thermostat or temperature control device fan switch to AUTO or ON. Set thermostat or temperature control device to initiate a first-stage cooling demand. A first-stage Y cooling demand will energize L reversing valve solenoid and compressor. Units With Optional Economizer - The optional economizer will start on a first stage (Y) cooling demand when outdoor air is suitable. An increased cooling demand (Y) will energize compressor. Refrigerant circuits are factory charged with R-40A refrigerant. See unit rating plate for correct amount of charge. D-Three Phase Scroll Compressor Voltage Phasing Three phase scroll compressors must be phased sequentially to ensure correct compressor and blower rotation and operation. Compressor and blower are wired in phase at the factory. Power wires are color-coded as follows: line -red, line -yellow, line -blue. - Observe suction and discharge pressures and blower rotation on unit start-up. - ion pressure must drop, discharge pressure must rise and blower rotation must match rotation marking. If pressure differential is not observed or blower rotation is not correct: - onnect all remote electrical power supplies. 4- Reverse any two field-installed wires connected to the line side of K contactor. Do not reverse wires at blower contactor. 5- Make sure the connections are tight. harge and suction pressures should operate at their normal start up ranges. IV-CHARGING WARNING-Do not exceed nameplate charge under any condition. This unit is factory charged and should require no further adjustment. If the system requires additional refrigerant, reclaim the charge, evacuate the system, and add required nameplate charge. NOTE - System charging is not recommended below 60 F (5 C). In temperatures below 60 F (5 C), the charge must be weighed into the system. If weighing facilities are not available, or to check the charge, use the following procedure: IMPORTANT - Charge unit in standard cooling mode high stage only. Make sure outdoor coil is clean. Attach gauge manifolds and operate unit at full CFM in cooling mode with economizer disabled until system stabilizes (approximately five minutes). Make sure all outdoor air dampers are closed. Compare the normal operating pressures (see tables 7-9) to the pressures obtained from the gauges. Check unit components if there are significant differences. Measure the outdoor ambient temperature and the suction pressure. Refer to the appropriate circuit charging curve to determine a target liquid temperature. Note - Pressures are listed for sea level applications. 6- Use the same thermometer to accurately measure the liquid temperature (in the outdoor section). If measured liquid temperature is higher than the target liquid temperature, add refrigerant to the system. If measured liquid temperature is lower than the target liquid temperature, recover some refrigerant from the system. 7- Add or remove charge in increments. Allow the system to stabilize each time refrigerant is added or removed. 8- Continue the process until measured liquid temperature agrees with the target liquid temperature. Do not go below the target liquid temperature when adjusting charge. Note that suction pressure can change as charge is adjusted. 9- Example ZH 06: At 95 F outdoor ambient and a measured suction pressure of 0psig, the target liquid temperature is 05.5 F. For a measured liquid temperature of 06 F, add charge in increments until measured liquid temperature agrees with the target liquid temperature. Page
TABLE 7 ZHA 06 NORMAL OPERATING PRESSURES - FIN/TUBE COIL Outdoor Coil Entering Temperature 65 F 75 F 85 F 95 F 05 F 5 F 9 5 7 4 4 6 59 9 409 46 8 4 0 79 9 6 64 46 4 40 470 9 45 46 85 5 55 77 55 48 59 48 45 48 54 90 6 5 70 84 74 48 79 498 TABLE 8 ZHA 048 NORMAL OPERATING PRESSURES - FIN/TUBE COIL Outdoor Coil Entering Temperature 65 F 75 F 85 F 95 F 05 F 5 F 5 6 9 9 6 8 5 45 8 49 58 97 6 4 9 87 440 7 498 67 8 08 4 54 46 40 5 459 54 56 40 7 48 7 55 66 6 48 67 475 7 56 TABLE 9 ZHA 060 NORMAL OPERATING PRESSURES - FIN/TUBE COIL Outdoor Coil Entering Temperature 65 F 75 F 85 F 95 F 05 F 5 F 54 5 9 9 5 80 5 40 8 487 60 99 6 4 0 9 4 440 7 496 0 65 8 08 4 54 47 404 5 456 54 5 6 70 45 5 5 64 60 44 67 47 7 59 0 ZHA06 CHARGING CURVE Outdoor Temperature ( F) 0 5 05 0 95 00 90 85 80 75 65 70 0 0 0 40 50 60 70 ion Pressure 80 Page 4
0 ZHA048 CHARGING CURVE Outdoor Temperature ( F) 5 0 05 0 95 00 85 90 75 80 65 70 0 0 0 40 50 60 70 ion Pressure 80 0 ZH060 CHARGING CURVE Outdoor Temperature ( F) 5 0 05 0 95 00 85 90 80 75 65 70 0 0 0 40 50 60 70 ion Pressure 80 Page 5