Multi-Position Air Handler with Energy-Saving Motor The Goodman brand Multi-Position Air Handler is suitable for use with refrigerants -0A and -. This unit s blower design includes an E fixed-speed motor that can enhance the efficiency of air conditioners and heat pumps. ½ to Tons Standard Features Suitable for use with refrigerants -0A and - heck flowrater expansion device for cooling and heat pump applications E fixed-speed motor Enhances the performance of your Goodman air conditioner or heat pump Multi-position upflow, downflow or horizontal Built-in coil has horizontal, vertical, and downflow drain pans with secondary drain connections omplies with the Factory-sealed Air Handling redit as listed in the 00 Florida Building ode, hapter, Section 0..A.. AHI ertified ETL Listed abinet Features Fully insulated, painted steel cabinet with attractive Architectural Gray finish Built-in filter rack for filter (filter not included) Low-voltage cabinet connections Power supply on top Low-voltage entry on top or side Factory-sealed to achieve % or less leakage rate at.0 water gauge external duct static pressure * To receive the 0-Year Parts Limited Warranty, online registration must be completed within 0 days of installation. Online registration is not required in alifornia or Québec. Full warranty details available at www.goodmanmfg.com. SS-G www.goodmanmfg.com /0 Supersedes /0
Nomenclature A S P F 0,,, 0 AA, Brand Engineering * A Single-piece Major/ Minor evisions Air Handler * Not used for inventory management Unit Application efrigerant harge eiling Mount PS Motor No Digit = - only D Downflow PS Motor = -0A or - E Multi-Position Variable-Speed Motor Multi-Position PS Motor Electrical S Multi-Position E Motor 0/0 V, Phase, 0 Hz W Wall Mount PS Motor Nominal apacity ange @ SEE abinet Finish Multi-Position & Downflow Applications U Unpainted ½ to ½ Tons (for Export Systems) P Painted 0 ½-½ Tons N Uncased -½ Tons eiling Mount & Wall Mount Applications Expansion Device (Nominal ooling apacity/ Electric Heat kw) F Flowrater 0 ½ Tons ooling/ kw Electric Heat T Expansion Valve 0 Tons ooling/ kw Electric Heat 0 Tons ooling/ kw Electric Heat www.goodmanmfg.com SS-G
Specifications 0 0 0 Nominal atings ooling (BTU/h),000-0,000 0,000 -,000 0,000 -,000,000-0,000 FM (High/ Low),0 / 0,0 / 00,0 / 00,000 /,00 Blower Diameter ½ 0⅝ 0⅝ 0 / Width 0⅝ 0⅝ 0 / oil Drain onnection FPT ¾ ¾ ¾ ¾ Service Valve Liquid ⅜ ⅜ ⅜ ⅜ Suction ¾ ⅞ ⅞ ⅞ Electrical Data Voltage 0 / 0 0 / 0 0 / 0 0 / 0 Electric Heat apacity (kw),, 0,,,, 0,, 0,,,,, 0,, 0, 0,, 0, Min ircuit Ampacity. /.. /.. /.. /. Max. Overcurrent Device / amps / amps / amps / amps Min. / Max VA / / / / Blower Motor A/ HP. / ½.0 / ¾.0 / ¾. / ¾ Ship Weight (lbs) SS-G www.goodmanmfg.com
Dimensions Model A B D E F G H I J 0 ¾ ½ ½ 0 ½ / ⅛ / 0 ¼ 0 ⅝ / ⅝ / / ¼ 0 ⅝ / ⅝ / / 0 ¼ 0 ⅝ / ⅝ / / www.goodmanmfg.com SS-G
Blower Performance Model 0 0 0 Motor Speed Tap FM deliverd against External Static Pressure 0. 0. 0. 0. 0. Low (T) 00 0 0 0 Med-Low (T) 0 0 Medium (T) 0 00 0 0 Med-High (T),0,0,0 0 High (T),0,,0,00,000 Low (T),00 00 0 Med-Low (T),0 0 0 Medium (T),,00,00 0 Med-High (T),,0,,0,00 High (T),,,0,, Low (T),00 00 0 Med-Low (T),0 0 0 Medium (T),,00,00 0 Med-High (T),,0,,0,00 High (T),,,0,, Low (T),,,00 0 Med-Low (T),,0,,0, Medium (T),0,0,,0, Med-High (T),0,0,0,0, High (T),,00,000,, Notes: Assumes dry coil with filter in place; SFM correction for wet coil = % All models are shipped from the factory with the speed tap set on T. SS-G www.goodmanmfg.com
****AA Wiring Diagrams HT TL M M HT TL HT TL M M M M HT TL HT TL HT TL HT TL HT TL HT TL HT TL M M M M M M M M M M M M M M B B L L L L L L L L ONE () ELENT OWS TWO () ELENT OWS THEE () ELENT OWS FOU () ELENT OWS L L L L NOTE: EN INSTALLING HEATE KIT, ENSUE SPEED TAP DOES NOT EXEED MINIMUM OWE SPEED (MBS) SPEIFIED FO THE AIHANDLE/HEATE KIT OMBINATION ON THIS UNIT'S S& PLATE. AFTE INSTALLING OPTIONAL HEAT KIT, MAK AN "X" IN THE POVIDED ABOVE. MAK AOING TO NUMBE OF HEATE ELENT OWS INSTALLED. NO MAK INDIATES NO HEAT KIT INSTALLED. SEE NOTE G W W Y Y O DH TINAL OK SHOWN FO 0HZ MODELS ONLY L L G EQUIPMENT GOUND USE OPPE O ALUMINUM WIE L 0/0 VOLTS L XFM- OM PLF PLF L G N PLF EBTD XFM- NO N G G XFM- XFM- OPPE O ALUMINUM POWE SUPPLY (SEE ATING PLATE) USE MIN. FIELD WIE G OM EBTD IF EPLAENT OF THE OIGINAL WIES SUPPLIED WITH THIS ASSY IS NEESSAY, USE WIE THAT ONFOMS TO THE NATIONAL ELETI ODE. NO N G G B A B SEE NOTE B V 0 T SEE NOTE SEE NOTE O B L G N T V OLO ODE AK ED YELLOW UE G B OMPONENT ODE PLF GEEN PLE BOWN ITE SEE NOTE EVAPOATO MOTO TB TINAL BOA ELAY ONTOL ELAY EBTD ELETONI OWE TIME DELAY ELAY B A G W W Y Y O DH T PLF ) Brown and white wires are used with Heat Kits only. WIING ODE FATOY WIING HIGH VOLTAGE LOW VOLTAGE FIELD WIING HIGH VOLTAGE LOW VOLTAGE TANSFOME FALE PLUG ONNETO MALE PLUG ONNETO FUSE LINK TL THAL LIMIT HT HEAT ELENTS Notes: ) ed wires to be on transformer terminal "" for 0 volts and on terminal "" for 0 volts. ) See composite wiring diagrams in installation instructions for proper low voltage wiring connections. ) onfirm speed tap selected is appropriate for application. If speed tap needs to be changed, connect red wire from terminal of relay to appropriate tap at TB Wiring is subject to change. Always refer to the wiring diagram on the unit for the most up-to-date wiring WANING High Voltage: Disconnect all power before servicing or installing this unit. Multiple power sources may be present. Failure to do so may cause property damage, personal injury, or death. 00A000 www.goodmanmfg.com SS-G
****BA Wiring Diagrams HT TL M M HT TL HT TL M M M M HT TL HT TL HT TL M M M M M M B HT TL HT TL HT TL HT TL M M M M M M M M B L L L L L L L L ONE () ELENT OWS TWO () ELENT OWS THEE () ELENT OWS FOU () ELENT OWS L L L L NOTE: EN INSTALLING HEATE KIT, ENSUE SPEED TAP DOES NOT EXEED MINIMUM OWE SPEED (MBS) SPEIFIED FO THE AIHANDLE/HEATE KIT OMBINATION ON THIS UNIT'S S& PLATE. AFTE INSTALLING OPTIONAL HEAT KIT, MAK AN "X" IN THE POVIDED ABOVE. MAK AOING TO NUMBE OF HEATE ELENT OWS INSTALLED. NO MAK INDIATES NO HEAT KIT INSTALLED. SEE NOTE TINAL OK SHOWN FO 0HZ MODELS ONLY L L EQUIPMENT GOUND USE OPPE O ALUMINUM WIE 0/0 VOLTS G WW Y Y O DH G L L PLF PLF L G N PLF G B B SEE NOTE SEE NOTE OPPE O ALUMINUM POWE SUPPLY (SEE ATING PLATE) USE MIN. FIELD WIE IF EPLAENT OF THE OIGINAL WIES SUPPLIED WITH THIS ASSY IS NEESSAY, USE WIE THAT ONFOMS TO THE NATIONAL ELETI ODE. G V SEE NOTE 0 T FUSE HOLDE O B L G N FUSE HOLDE T TB EBTD V OLO ODE AK ED YELLOW UE PLF G W W Y Y O DH G B OMPONENT ODE GEEN PLE BOWN ITE EVAPOATO MOTO TINAL BOA ELAY ONTOL ELAY ELETONI OWE TIME DELAY ELAY WIING ODE FATOY WIING HIGH VOLTAGE LOW VOLTAGE FIELD WIING HIGH VOLTAGE LOW VOLTAGE T PLF TL HT TANSFOME FALE PLUG ONNETO MALE PLUG ONNETO FUSE LINK THAL LIMIT HEAT ELENTS Notes: ) ed wires to be on transformer terminal "" for 0 volts and on terminal "" for 0 volts. ) See composite wiring diagrams in installation instructions for proper low voltage wiring connections. ) onfirm speed tap selected is appropriate for application. If speed tap needs to be changed, connect purple wire from terminal of relay to appropriate tap at TB ) Brown and white wires are used with Heat Kits only. 00A000 EV B Wiring is subject to change. Always refer to the wiring diagram on the WANING unit for the most up-to-date wiring High Voltage: Disconnect all power before servicing or installing this unit. Multiple power sources may be present. Failure to do so may cause property damage, personal injury, or death. SS-G www.goodmanmfg.com
Accessories Heat Kit Selection 0 0 0 HK-0* X X X X HK-0*, HK-0* X X X X HK-0* X X X X HK-0*, HK-0* X¹ X¹ X¹ X HK-0*, HK-0* X¹ X¹ X¹ X HK-* X² X² X² X¹ HK-0* X² X² X¹ HK-* X² X² X¹ ^ HK-* X² X² X² X¹ ^ HK-0* X² X² X¹ * evision level that may or may not be designated ircuit breaker option ^ Heat kit requires three-phase power supply ¹ Air handler must be on speed tap,,, or ² Air handler must be on speed tap or. Single Point Kit ** Model HK- HK-0 HK- SPW-0 X X X ** Must be installed along with any of the above compatible heat kits. This kit will fit any air handler as long as a compatible heat kit is installed in the unit. Filters Filter # Qty equired 0 FIL-- 0 FIL - 0 FIL - Expansion Valve Kits for Air onditioning and Heat Pump Applications Kit Number Description Application efrigerant Tonnage: Outdoor Unit XVB- 0% Bleed Valve A Only - ½ - Ton XVB-0 0% Bleed Valve A Only - ½ - Ton XV- Non-bleed Valve A Only - ½ - Ton XV-0 Non-bleed Valve A Only - ½ - Ton TXN Non-bleed Valve A or HP - ½ - Ton TXN Non-bleed Valve A or HP - ½ - Ton TXN Non-bleed Valve A or HP - ½ - Ton TXN Non-bleed Valve A or HP -0A ½ - Ton TXN Non-bleed Valve A or HP -0A ½ - Ton TXN Non-bleed Valve A or HP -0A ½ - Ton Drain Pan Insulation Kits Downflow Applications Horizontal Applications hassis Size Insulation Kit hassis Size Insulation Kit Small (½ ) DPI-0/0 Small (½ ) DPIH- Medium (½ ) DPI-/0 Medium (½ ) DPIH- Large ( ) DPI-0/0 Large ( ) DPIH- Note: Each kit contains enough material to modify 0 coils Note: Each kit contains enough material to modify 0 coils Goodman Manufacturing ompany, L.P., reserves the right to discontinue, or change at any time, specifications or designs without notice or without incurring obligations. 00 Goodman Manufacturing ompany, L.P. Houston, Texas Printed in the USA. www.goodmanmfg.com SS-G