Tel. +39 075.5280260 Fax +39 075.5287033 Via Pizzoni 37/39 06132 Perugia ITALY www.umbrarimorchi.it umbrarimorchi@umbrarimorchi.it ISTRUZIONI DI MONTAGGIO FITTING INSTRUCTIONS INSTRUCTIONS DE MONTAGE MONTAGEANLEITUNG INSTRUCCIONES DE MONTAJE DISPOSITIVO DI TRAINO TIPO TOWING BRACKET TYPE DISPOTIF DE REMORQUAGE TYPE ANHAENGEVORRICHTUNG TYP DISPOSITIVO DE CAREO TIPO PER AUTOVEICOLI FOR CARS POUR AUTOS FUR KRAFTAHRZEUGE PARA AUTOVEHICULO BMW 5 SERIE 346 TYPE CLASSE E TIPO DI ATTACCO CLASS AND HITCH TYPE CLASSE ET TYPE DE CROCHET KLASSE UND BEFESTIGUNGSART CLASES DE ACOPLAMIENTO OMOLOGAZIONE CARICO VERTICALE MAX S VALUE MASSE VERTICALE MAXIMUM ZUL. STUETZLAST CARGA MAX. VERTICAL HOMOLOGATION HOMOLOGATION ZULASSUNG APROBACION e3 00 0334 A50-X 1996 2003 S = kg 90 (DIR. 94/20/CE) VALORE D D VALUE VALEUR D D WERT VALOR D 11,2 kn D = 11,2 kn COPPIA DI SERRAGGIO PER VITI (8.8): TORQUE SETTINGS FOR NUTS AND BOLTS (8.8): COUPLE DE SERRAGE POUR VIS (8.8): SCHRAUBENANZUGSMOMENT (8.8): MOM. DE PRESION PARA TORNILLOS Y TUERCAS (8.8): M6 = 10 Nm M10 = 55 Nm M14 = 135 Nm M8 = 25 Nm M12 = 85 Nm M16 = 200 Nm P. 1 / 6
SAFETY INSTRUCTIONS Make sure that the towbar is suitable for the vehicle before starting the installation. For safety, all work involving towbar installation (incl. electrical components) must be undertaken by skilled technicians. Damaged components must be replaced with manufacturer s spares and fitted by qualified staff. It is forbidden to make any modification or structural repair to towing assembly. The tow-ball must be kept clean and lubricated. For added safety, his diameter (50 mm) must be checked at regular intervals. If the tow-ball measures less than 49 mm after selected readings across the diameter, the tow-ball must be replaced with a new one. After 1000 km of towing, check torque settings for nuts and bolts, in accordance with the table. Umbra Rimorchi cannot be held responsible for any defects in the product caused by fault or by any injudicious use whatever of the user or a person he is liable for. P. 2 / 6
FITTING INSTRUCTIONS BMW 5 SERIES Remove all underseals from areas which may come in contact with the towbar assembly and re-coat areas with anti-rust paint. The holes for fixing the towing structure are existing. 1. Raise boot cover, remove rear bumper and discard bumper's bearings. Make a cut in the middle of the lower edge of bumper beam as shown. 2. Locate cross-bar A into the rear bumper, mark the four holes 4 on its lower edge and remove temporarily cross-bar A. 3. Drill Ø 22mm holes 4 where marked, position again cross-bar A into the rear bumper and fix it using the original bolts and nuts. Fix item E to the cross bar A referring to holes 4 (working from the exterior side of the rear bumper) and insert the spacers D to avoid the crushing of the bumper. 4. Position side arms B into chassis rails, referring to holes 1 and fix in position 2 and 3, insert items C, together with large washer 2 from inside the boot. 5. Position the assembled set (rear bumper + cross bar) along the back side of the car referring to holes 1 and fix. 6. Tighten all the bolts and nuts. 7. Re-fit spare wheel and boot cover. DISAPPEARING SOCKET P. 3 / 6
BMW 5 SERIES BUMPER BEAM CUT BOLTS ANDS NUTS 1. N. 6 NUTS M10 -contact 2. N. 2 SCREWS M10X30- contact -plate Ø30 3. N.2 SCREWS M10x30 -contact 4. N.4 SCREWS M10x35 contact- WELDED NUT 5. N.2 SCREWS M10x80 -contact-nut P. 4 / 6
P. 5 / 6
P. 6 / 6