Drawing A Crankcase, Cylinder 1
Drawing A Crankcase, Cylinder Reference Item number Qty Description 1 4241 021 0300 1 Crankcase 2 9639 003 1230 2 Oil seal 12x22x7 3 9523 003 0000 2 Grooved ball bearing 12x32x10.8 4 4241 030 0401 1 Crankshaft (25.2005) 5 4144 021 2500 1 Engine pan 6 9512 003 1832 1 Needle cage 8x11x10 7 4144 029 2301 1 Cylinder gasket 8 4241 020 1202 1 Cylinder with piston Ø 34 mm (1-3) 10-14 9 4241 020 1200 1 Cylinder with piston Ø 34 mm (4-6) 10-14 10 4241 030 2001 1 Piston Ø 34 mm 11-13 11 4144 034 3000 2 Piston ring Ø 34x1.2 mm 12 9463 650 0805 1 Snap ring 8x0.7 13 4241 034 1500 1 Piston pin 8x5x22 14 9075 478 4268 4 Pan head self-tapping screw IS-D5x60 15 0000 400 7011 1 Spark plug NGK CMR6H 16 0783 830 2000 1 Tube of sealant Dirko HT red (B) 4144 007 1012 1 Set of gaskets 2, 7 (1) SH 56-D, (2) SH 56 C-E D, (3) SH 56 C-E Z, (4) SH 86-D, (5) SH 86 C-E D, (6) SH 86 C-E Z 2
Drawing B Ignition system, Muffler 3
Drawing B Ignition system, Muffler Reference Item number Qty Description 1 4241 400 1302 1 Ignition module (1,2,3) 3, 4 2 4241 400 1307 1 Ignition module (4,5,6) 3, 4 3 0000 998 0604 1 Torsion spring 4 4241 405 1000 1 Spark plug boot 5 4241 405 8000 1 Insulator 6 4241 431 2100 1 Connector tag 7 9075 478 3018 2 Pan head self-tapping screw IS-D4x18 8 9291 021 0100 1 Washer 4.3 9 4241 084 1100 1 Spiral housing 10 9075 478 4136 3 Pan head self-tapping screw IS-D5x20 11 4241 400 1200 1 Flywheel (25.2005) 12 0000 955 0802 1 Collar nut M8x1 13 4144 149 0600 1 Muffler gasket 14 4241 140 0605 1 Muffler (1,2,4,5) 15 9075 478 4136 2 Pan head self-tapping screw IS-D5x20 16 4241 140 0600 1 Muffler (3,6) USA, AUS, CDN 17 17 4229 140 6905 1 Stub with screen (3,6) USA, AUS, CDN 4144 007 1012 1 Set of gaskets 13 (1) SH 56-D, (2) SH 56 C-E D, (3) SH 56 C-E Z, (4) SH 86-D, (5) SH 86 C-E D, (6) SH 86 C-E Z 4
Drawing C Air filter, Spacer flange 5
Drawing C Air filter, Spacer flange Reference Item number Qty Description 1 4241 120 1800 1 Filter 2 4241 141 1100 1 Insert 3 4241 140 1000 1 Filter cover 4 4 1 Twist lock (D) 5 4241 121 6900 1 Baffle 6 9210 261 0700 2 Hexagon nut M5 7 4241 141 0802 1 Filter housing (1,2,4,5) 8 4241 140 2800 1 Filter housing (3,6) 9 4114 149 1205 1 Gasket 10 4241 120 0601 1 Carburetor C1M-S142C (1,2,3) 11 4241 120 0600 1 Carburetor C1M-S141B (4,5,6) 12 4128 129 0900 1 Gasket 13 9075 478 4136 3 Pan head self-tapping screw IS-D5x20 14 4144 120 2301 1 Spacer flange 15 4144 129 0900 1 Gasket 4144 007 1012 1 Set of gaskets 9, 12, 15 (1) SH 56-D, (2) SH 56 C-E D, (3) SH 56 C-E Z, (4) SH 86-D, (5) SH 86 C-E D, (6) SH 86 C-E Z 6
Drawing D Rewind starter 7
Drawing D Rewind starter Reference Item number Qty Description 4241 080 2102 1 Fan housing with rewind starter (1) 1-9 4241 080 2100 1 Fan housing with rewind starter (4) 1-8, 10, 11 1 4241 080 1800 1 Fan housing (1,4) 2 2 9416 868 6650 1 Rivet 6.5x0.5x8.8 (1,4) 3 4237 190 0600 1 Rewind spring (1,4) 4 4241 195 0400 1 Rope rotor (1,4) 5 1123 195 7200 2 Pawl (1,4) 6 0000 958 0923 1 Washer (1,4) 7 1128 195 3500 1 Spring (1,4) 8 1120 195 8200 1 Starter rope Ø 3x1060 mm (1,4) 0000 930 2208 1 Starter rope Ø 3 mm x 30.5 m (B) (1,4) 9 4140 195 3400 1 Starter grip (1) 10 0000 190 3404 1 Starter grip ElastoStart Ø 3 mm (B) (4) 8, 11 11 0000 195 7000 1 Cap (B) (4) 12 4241 967 1520 1 Model plate SH 56 (1) 13 4241 967 1522 1 Model plate SH 86 (4) 14 0000 951 1100 3 Screw IS-D5x20 (1,4) (1) SH 56-D, (2) SH 56 C-E D, (3) SH 56 C-E Z, (4) SH 86-D, (5) SH 86 C-E D, (6) SH 86 C-E Z 8
Drawing E Rewind starter ErgoStart/Easy2Start 9
Drawing E Rewind starter ErgoStart/Easy2Start Reference Item number Qty Description 4241 080 2101 1 Fan housing with rewind starter (2,3,5,6) 1-11 1 4241 080 1800 1 Fan housing (2,3,5,6) 2 2 9416 868 6650 1 Rivet 6.5x0.5x8.8 (2,3,5,6) 3 4237 190 0600 1 Rewind spring (2,3,5,6) 4 4241 195 0403 1 Rope rotor (2,3,5,6) 5 4241 195 3501 1 Spring (2,3,5,6) 6 4241 195 2001 1 Carrier (2,3,5,6) 7 1123 195 7200 2 Pawl (2,3,5,6) 8 0000 958 0923 1 Washer (2,3,5,6) 9 1128 195 3500 1 Spring (2,3,5,6) 10 1120 195 8200 1 Starter rope Ø 3x1060 mm (2,3,5,6) 0000 930 2208 1 Starter rope Ø 3 mm x 30.5 m (B) (2,3,5,6) 11 4140 195 3400 1 Starter grip (2,3,5,6) 12 4241 967 1521 1 Model plate SH 56 C (2,3) 13 4241 967 1523 1 Model plate SH 86 C (5,6) 14 0000 951 1100 3 Screw IS-D5x20 (2,3,5,6) (1) SH 56-D, (2) SH 56 C-E D, (3) SH 56 C-E Z, (4) SH 86-D, (5) SH 86 C-E D, (6) SH 86 C-E Z 10
Drawing F Carburetor C1M-S142C 11
Drawing F Carburetor C1M-S142C Reference Item number Qty Description 4241 120 0601 1 Carburetor C1M-S142C (1,2,3) 1-25 1 4128 122 3000 1 Spring (1,2,3) 2 4116 121 5100 1 Inlet needle (1,2,3) 3 1125 121 5000 1 Inlet control lever (1,2,3) 4 1120 121 9200 1 Spindle (1,2,3) 5 4241 122 6600 1 Collar screw (1,2,3) 6 4241 129 0901 1 Gasket (1,2,3) 7 4241 121 4700 1 Metering diaphragm (1,2,3) 8 4241 120 2200 1 Flange (1,2,3) 9 4226 121 2700 1 Cap (1,2,3) 10 4140 121 0800 1 End cover (1,2,3) 11 4241 122 7100 4 Screw (1,2,3) 12 4241 121 4800 1 Pump diaphragm (1,2,3) 13 1123 129 0905 1 Gasket (1,2,3) 14 4241 121 0800 1 End cover (1,2,3) 15 1125 122 4200 1 Ball (1,2,3) 16 4140 122 6200 1 Idle speed adjustment screw (1,2,3) 17 1120 122 7800 1 Oval head screw (1,2,3) 18 1123 121 7800 1 Strainer (1,2,3) 19 4241 122 6801 1 Low speed adjustment screw (1,2,3) 20 4241 122 6700 1 High speed adjustment screw (1,2,3) 21 4229 121 2701 1 Cap (1,2,3) 22 9079 319 0280 1 Flat head screw M3x3.5 (1,2,3) 23 4241 121 3500 1 Throttle lever (1,2,3) 24 4241 122 5000 1 Spacer sleeve (1,2,3) 25 4241 182 9500 1 Choke knob (1,2,3) 4241 007 1002 1 Set of carburetor parts (1,2,3) 7,8,12,13 (1) SH 56-D, (2) SH 56 C-E D, (3) SH 56 C-E Z, (4) SH 86-D, (5) SH 86 C-E D, (6) SH 86 C-E Z 12
Drawing G Carburetor C1M-S141B 13
Drawing G Carburetor C1M-S141B Reference Item number Qty Description 4241 120 0600 1 Carburetor C1M-S141B (4,5,6) 1-25 1 4128 122 3000 1 Spring (4,5,6) 2 4116 121 5100 1 Inlet needle (4,5,6) 3 1125 121 5000 1 Inlet control lever (4,5,6) 4 1120 121 9200 1 Spindle (4,5,6) 5 4241 122 6600 1 Collar screw (4,5,6) 6 4241 129 0901 1 Gasket (4,5,6) 7 4241 121 4700 1 Metering diaphragm (4,5,6) 8 4241 120 2200 1 Flange (4,5,6) 9 4226 121 2700 1 Cap (4,5,6) 10 4140 121 0800 1 End cover (4,5,6) 11 4241 122 7100 4 Screw (4,5,6) 12 4241 121 4800 1 Pump diaphragm (4,5,6) 13 1123 129 0905 1 Gasket (4,5,6) 14 4241 121 0800 1 End cover (4,5,6) 15 1125 122 4200 1 Ball (4,5,6) 16 4140 122 6200 1 Idle speed adjustment screw (4,5,6) 17 1120 122 7800 1 Oval head screw (4,5,6) 18 1123 121 7800 1 Strainer (4,5,6) 19 4241 122 6800 1 Low speed adjustment screw (4,5,6) 20 4241 122 6700 1 High speed adjustment screw (4,5,6) 21 4229 121 2701 1 Cap (4,5,6) 22 9079 319 0280 1 Flat head screw M3x3.5 (4,5,6) 23 4241 121 3500 1 Throttle lever (4,5,6) 24 4241 122 5000 1 Spacer sleeve (4,5,6) 25 4241 182 9500 1 Choke knob (4,5,6) 4241 007 1002 1 Set of carburetor parts (4,5,6) 7,8,12,13 (1) SH 56-D, (2) SH 56 C-E D, (3) SH 56 C-E Z, (4) SH 86-D, (5) SH 86 C-E D, (6) SH 86 C-E Z 14
Drawing H Fan housing outer, Fanwheel 15
Drawing H Fan housing outer, Fanwheel Reference Item number Qty Description 1 4241 700 4102 1 Fan housing, outer 2 2 0000 967 4001 1 Warning pictogram: Fan grille 3 9074 477 4132 6 Pan head self-tapping screw IS-P5x18 4 4241 706 8000 1 Screen 5 0000 998 0401 1 Torsion spring 6 9211 260 1150 1 Hexagon nut M8x1 l/h thread 7 4229 704 7900 2 Washer 8 4229 768 0300 1 Schredder blade 9 4241 704 3400 1 Fanwheel (1) SH 56-D, (2) SH 56 C-E D, (3) SH 56 C-E Z, (4) SH 86-D, (5) SH 86 C-E D, (6) SH 86 C-E Z 16
Drawing J Fan housing inside SH 56 17
Drawing J Fan housing inside SH 56 Reference Item number Qty Description 1 4241 700 4101 1 Fan housing (1,2,3) 2-12, 14 2 9443 825 7130 4 Hollow rivet 7.5x1x6.8 (1,2,3) 3 9371 470 2680 1 Cylindrical pin 5x28 (1,2,3) 4 0000 350 5800 1 Tank vent (1,2,3) 5 4238 353 9200 1 Grommet (1,2,3) 6 4241 353 2700 1 Connector (1,2,3) 7 1 Hose 3.1x5.7x76 mm (D) (1,2,3) 8 1 Hose 3.1x5.7x120 mm (D) (1,2,3) 0000 930 2803 1 Hose 3.1x5.7 mm x 1 m (B) (1,2,3) 9 4241 358 7700 1 Hose (1,2,3) 10 4223 350 0500 1 Filler cap (1,2,3) 11, 12 11 9645 951 3890 1 O-ring 35x3-FPM 80 (1,2,3) 12 0000 350 0900 1 Rope (1,2,3) 13 0000 350 3502 1 Pickup body (1,2,3) 14 0000 967 3796 1 Warning pictogram BG (1,2,3) 15 4241 967 3503 1 Instruction label SH 56 (1,2,3) USA 16 0000 967 3501 1 Instruction label (1,2,3) USA 17 0000 967 3693 1 Warning pictogram Filler cap (1,2,3) USA, CDN 18 4241 440 1900 1 Lead (1,2,3) 19 4241 440 1901 1 Lead (1,2,3) 20 4241 430 8900 1 Stop button (1,2,3) 21 4241 182 1000 1 Throttle trigger (1,2,3) 22 4241 182 1500 1 Throttle rod (1,2,3) 23 4241 791 0600 1 Handle molding (1,2,3) 24 9074 477 4132 3 Pan head self-tapping screw IS-P5x18 (1,2,3) 25 9075 478 4159 4 Pan head self-tapping screw IS-D5x24 (1,2,3) (1) SH 56-D, (2) SH 56 C-E D, (3) SH 56 C-E Z, (4) SH 86-D, (5) SH 86 C-E D, (6) SH 86 C-E Z 18
Drawing K Fan housing inside SH 86 19
Drawing K Fan housing inside SH 86 Reference Item number Qty Description 1 4241 700 4100 1 Fan housing (4,5,6) 2-5 2 9443 825 7130 3 Hollow rivet 7.5x1x6.8 (4,5,6) 3 4241 792 2901 4 Bearing plug (4,5,6) 4 4241 791 3100 4 Spring (4,5,6) 5 4241 792 2900 4 Bearing plug (4,5,6) 6 4241 791 0200 1 Handle (4,5,6) 7 4241 791 7500 1 Cover (4,5,6) 8 9074 477 4132 4 Pan head self-tapping screw IS-P5x18 (4,5,6) 9 4241 967 3504 1 Instruction label SH 86 (4,5,6) USA 10 0000 967 3501 1 Instruction label (4,5,6) USA 11 9075 478 4159 3 Pan head self-tapping screw IS-D5x24 (4,5,6) 12 4241 791 0802 2 Handle molding (4,5,6) (1) SH 56-D, (2) SH 56 C-E D, (3) SH 56 C-E Z, (4) SH 86-D, (5) SH 86 C-E D, (6) SH 86 C-E Z 20
Drawing L Handle frame SH 86 21
Drawing L Handle frame SH 86 Reference Item number Qty Description 1 4241 790 5600 1 Handle frame (4,5,6) 2-10, 12 2 0000 350 5800 1 Tank vent (4,5,6) 3 4238 353 9200 1 Grommet (4,5,6) 4 4241 353 2700 1 Connector (4,5,6) 5 1 Hose 3.1x5.7x76 mm (D) (4,5,6) 6 1 Hose 3.1x5.7x120 mm (D) (4,5,6) 0000 930 2803 1 Hose 3.1x5.7 mm x 1 m (B) (4,5,6) 7 4241 358 7700 1 Hose (4,5,6) 8 4223 350 0500 1 Filler cap (4,5,6) 9, 10 9 9645 951 3890 1 O-ring 35x3-FPM 80 (4,5,6) 10 0000 350 0900 1 Rope (4,5,6) 11 0000 350 3502 1 Pickup body (4,5,6) 12 0000 967 3796 1 Warning pictogram BG (4,5,6) 13 0000 967 3693 1 Warning pictogram Filler cap (4,5,6) USA, CDN 14 4241 791 0801 1 Handle molding, outer (4,5,6) 15 4241 430 8900 1 Stop button (4,5,6) 16 4241 440 3000 1 Wiring harness (4,5,6) 17 4241 182 1001 1 Throttle trigger (4,5,6) 18 4241 182 4300 1 Cam (4,5,6) 19 4241 182 4200 1 Detent spring (4,5,6) 20 4241 182 1500 1 Throttle rod (4,5,6) 21 4241 791 0605 1 Handle molding (4,5,6) 22 4241 182 2900 1 Locking lever (4,5,6) 23 4241 791 0800 1 Handle molding, inner (4,5,6) 24 9074 477 4132 4 Pan head self-tapping screw IS-P5x18 (4,5,6) (1) SH 56-D, (2) SH 56 C-E D, (3) SH 56 C-E Z, (4) SH 86-D, (5) SH 86 C-E D, (6) SH 86 C-E Z 22
Drawing M Nozzle, Vacuum attachment 23
Drawing M Nozzle, Vacuum attachment Reference Item number Qty Description 1 4229 708 6300 1 Nozzle 2 4229 708 6301 1 Nozzle (4,5,6) 3 4241 708 6302 1 Nozzle (B) 4 4241 760 8200 1 Tube 5, 6 5 4241 703 5600 1 Screen 6 4241 708 3100 1 Union nut 4241 700 2200 1 Vacuum attachment 7-11 7 4241 760 3501 1 Suction tube 8 8 0000 967 3631 1 Warning pictogram BG 9 4241 700 6900 1 Elbow 10 4229 708 9702 1 Catcher bag 11 4227 710 9003 1 Harness 12 0000 791 8400 1 Ring (B) 2 pieces 13 0000 884 0307 1 Safety glasses 14 4180 890 3400 1 Combination wrench (B) 15 0000 890 2300 1 Screwdriver (B) (1) SH 56-D, (2) SH 56 C-E D, (3) SH 56 C-E Z, (4) SH 86-D, (5) SH 86 C-E D, (6) SH 86 C-E Z 24
Drawing N Gutter cleaning 25
Drawing N Gutter cleaning Reference Item number Qty Description 4241 007 1003 1 Gutter cleaning kit (B) 1-4 1 4241 708 0100 1 Adapter (B) 2 3 Hose clip (D) 3 3 Tube (D) 4 2 Manifold (D) (1) SH 56-D, (2) SH 56 C-E D, (3) SH 56 C-E Z, (4) SH 86-D, (5) SH 86 C-E D, (6) SH 86 C-E Z 26