Replacement Parts List No. 700005300 Revision E 12/2017 McQuay Centrifugal Chiller WPV 320A - 350A Last Manufactured: 2008 To find your Daikin Applied parts distributor, call 1-800-377-2787 or visit www.daikinapplied.com
Contents Parts List Revision History...3 Electrical Legend...4 Nomenclature Nameplate Locations and Part Numbers...5 Unit Dataplate...6 Model Number- Unit, Style Number- Unit, Serial Number- Unit...6 Model Number- Complete... 7-8 Control Box Unit Control Box Mounting Components...9 Unit Control Box Detail- Until 5/05...10-11 MicroTech II Unit Control Box Detail- 5/05 and Later... 12-13 Compressor Control Box Mounting Components... 14-16 Cables and Sensors... 17-19 Starter...20 Liquid Line Expansion Valve, Ball Valve, Sight Glass, King Valve, Flanges, Gaskets, O'Rings, Pilot Valve Sensor Well, Tubing... 21-22 Expansion Valve Detail...23 Condenser & Evaporator Valves...24 Insulation...25 Condenser... 26-27 Evaporator... 28-29 Compressor Nomenclature...30 Mounting Brackets and Hardware...31 4- Way SA/SB Solenoid Valve & Tubing...32 Motor Drain Line, Motor Cooling Line, Liquid Injection... 33-34 Suction & Discharge Lines- Suct Victaulics, Pipes, Seals, Disch Nozzle, Flanges, Ck Valve...35 Section Assembly- Main Sections, O'Rings, Screws...36 Front End Inlet Section: Vanes, Piston, Cone, Seals...37 Main Gear Train- Impeller, Volute, Diffuser, Oil Filter, Spin Down, Low Speed Gear, Low Speed Bearings, Gear Housing and Seals... 38-39 High Speed Assembly- Pinion, Thrust Pump, High Speed Bearings, Seals... 40-41 Gears- High Speed (Pinion) & Low Speed (Bull)...41 O'Ring Kits...41 Motor Section- Housing, Sight Glass, Motor, Terminals, Seals, Hardware... 42-43 Stators, Rotor/Shaft Assembly... 44-49 Discharge Flange/O'Ring, External Flanges, Valves, Fittings and Blockoffs...50 Motor Terminal Box...51 Oil Pump... 52-58 RPL 7000053 / Page 2
Parts List Revision History Revision Date Description 03/05 New A 5/09 Page 9- Add "Operator Interface Panel" p/n 330277501. Add Power cord p/n 300040768. Add footnote "*". Add note to diagram. Pages 10,11- Add "Until 5/05" to header. Pages 12,13- Add pages- drawing and chart for Control Box-MicroTech Detail-5/05 and later. Page 28- Ref #100 Tubes change p/n to 330441408. Page 40- Ref#561 O'ring change p/n to 735073693. Page 44- Ref #731 add footnote 5 to p/n. Add footnote 5- "074608103 may also be used." Page 56- Ref # 230 U Bolt change p/n to 330861101. Page 59- Add Complete Oil Assy-Service p/n 350147201S and footnote 4. Add footnote 4-"Complete assy includes oil pump & heaters (Heater p/n 735041227 qty=2) B 5/09 Page 19 - Ref #350 change Sensor-Oil Sump p/n form 071568701 to 330198001. C 4/12 Page 9 - Expanded information for Operator Interface Panel. Page 11 - Updated info for Serial Gateway controls. Added * note about original control box. Pages 12 & 13 - Removed Ref. 9: Screw, Ref. 13: Label & Ref. 21: Label from drawing and chart. Page 14: Removed Ref. 260 Compressor Control Box from drawing and chart. Pages 15 & 16 - Removed Ref. 25, 29 & 33: Labels from drawing and chart. Page 19 - Added p/n for Ref. 220: Sensor Well- 3/05 & later. Added p/n for Ref. 551: Sensor-3/05 & later. Added footnotes 6 & 7. Page 20 - Deleted page: Communications Options. Following pages re-numbered. Page 27 - Removed Condenser Heads, Screw, Nut p/n's. Added note to contact McQuayParts. Page 29 - Removed Evaporator Heads, Screw, Nut p/n's. Added note to contact McQuayParts. Page 32- Corrected information for Installation Kit. Ref. 402 & 408 not included in kit. Page 34 - Added p/n for Ref. 320: Valve-Ball- 4/10 & later. Page 58 - Added p/n under Ref. 326 for O'Ring- Rotolock Fitting. D 07/17 Page 9- Corrected descriptions for Ref. 15, added Power Cord. Page 11- Corrected description for Ref. 7, was BACnet w/rs232, now BACnet w/ms/tp. Page 35- Corrected size for Ref. 125 Discharge Check Valve, was 5". E 12/17 Cover: Added Last Manufactured date. Daikin Applied, 13600 Industrial Park Blvd., P.O. Box 1551, Minneapolis, MN 55440 (763) 553-5330 RPL 7000053 / Page 3
Electrical Legend Sch. Sym. Description Location 1M, 2M Contactor Starter 1S, 2S Energizing Contactor Starter CAP Capacitor Compressor Control Box CB Circuit Breaker Unit Control Box CF Condenser Flow Switch Tube Sheet Support CR Relay Compressor Control Box CS01- CS10 Sensors- Compressor Controller Throughout Unit CTB1, CTB2 Terminal Block Compressor Control Box DIST/ISO Dist. & Isolation Board Unit Control Box EF Evaporator Flow Switch Tube Sheet Support HR Relay Compressor Control Box LR Relay Compressor Control Box MCR Motor Control Relay Starter Panel OITS Operator Interface Touch Screen OL Oil Pump Overload Compressor Control Panel OP Oil Pump Contactor Compressor Control Panel pc02 Main Controller Unit Control Box PHP1 High Pressure Transducer Discharge Nozzle RES Transition Resistor Starter SA/SB 4- Way Vane Speed Solenoid Compressor Gear Housing SC Signal Converter Compressor Control Box T1, T2, T3 Main Control Transformer Starter TR Timing Relay Starter TRP Transition Resistance Protector Starter US02- US10 Sensor- Unit Controller Throughout Unit UTB1 Unit Control Terminal Block Unit Control Box RPL 7000053 / Page 4
Nomenclature Nameplate Locations and Part Numbers Unit Dataplate pn: 070191901 End View Compressor Dataplate pn: 071583501 Evaporator Dataplate pn: 719813601 (until 8/03) pn: 330528601 (8/03 & later) Front View Condenser Dataplate pn: 719813601 (until 8/03) pn: 330528601 (8/03 & later) RPL 7000053 / Page 5
Nomenclature Unit Dataplate Model Number- Unit WPV 320 A Unit Model WPV= Water- Cooled Single Compressor Centrifugal Chiller Always A Unit Capacity 320= 300 to 320 tons nominal 350= 330 to 350 tons nominal Style Number- Unit E 923456 010 Always "E" 6- Digit G.O. Number G.O. Item Number Serial Number- Unit STN U 01 05 048 Plant Identification Abbreviation STN = Staunton U= Unit Year of Manufacture 02= 2002 03= 2003 04= 2004 05= 2005 06= 2006 07= 2007 etc. Serial Number (build sequence) Month of Manufacture 01= January 07= July 02= February 08= August 03= March 09= September 04= April 10= October 05= May 11= November 06= June 12= December RPL 7000053 / Page 6
1. Model Type WPV= Water Cooled Centrifugal Chiller 2. Unit Size 320= 300 to 320 tons nominal 350= 330 to 350 tons nominal 3. Gear Ratio Code (speed code) A2, AY, AZ Nomenclature Model Number- Complete WPV 320A AZ 35B 2LA 0450 2LAYYY 1370 A DY 2LEMBA 2RYYSYYY Code: 1 2 3 4 5 6 7 8 9 10 11 12 Y 1 V 0320 U Y Y 0 A 250 0215 YY M Code: 13 14 15 16 17 18 19 20 21 22 23 24 25 4. Motor Horsepower/Voltage first 2 digits= horsepower, third digit= voltage 60 Hz. Codes 23= 230HP 25= 250HP 29= 290HP 31= 300HP 32= 320HP 34= 350HP 35= 350HP 40= 400HP 41= 400HP 50 Hz. Codes 23= 242HP 25= 265HP 29= 292HP 31= 292HP 32= 340HP 34= 333HP 35= 333HP 41= 375HP 60 Hz. Codes N= 200V B= 208V P= 220V V= 230V 4= 400V A= 440V R= 460V S= 480V D= 575V Q= 416V 50 Hz. Codes E= 220V Y= 346V F= 380V G= 400V K= 415V H= 440V Z= 500V 5. Evaporator Head Description first digit= Number of Water Passes: 2 second digit= Inlet Nozzle Location: L= Left third digit= Nozzle Type: A= Victaulic R= Right 6. Evaporator Leaving Water Temperature Code is listed in tenths of F (example 0450= 45.0 F) 7. Condenser Head Description first digit= Number of Water Passes: 2 second digit= Inlet Nozzle Location: L= Left third digit= Nozzle Type: A= Victaulic fourth digit= always Y fifth digit= always Y sixth digit= always Y R= Right 8. Maximum Condenser Leaving Water Temperature Code is listed in tenths of F (example 1370= 137.0 F) 9. Condenser Model Revision A= Revision A 10. Main Expansion Valve/ Pilot Valve first digit= Main Expansion Valve: P= 800 ton TXV; Q= 550 ton TXV second digit= Pilot Valve: B= 9 ton 11. Controller Options first digit= Control Type: 2= MicroTech II second digit= Size: L= Large third digit= Language: E= English Language fourth digit= Instruments: M= Modem; Y= None fifth digit= Communications: B= BACnet; E= BACnet w/ethernet; L= LonWorks; M= MODBUS; P= Serial Port w/modem; S= Serial Port (RS232) sixth digit= Enclosure: A= NEMA 1 RPL 7000053 / Page 7
Nomenclature Model Number- Complete Continued 12. Starter Options first digit= Starter Type: 2= Wye-Delta Closed; 6= Solid State second digit= Enclosure: R= 72" High Terminal Mounted third digit= Meters: Y= None fourth digit= Disconnect: Y= None fifth digit= Surge Protection Capacitor: S= Surge Capacitor mounted in Starter Box sixth digit= Phase Loss/Rotation Protection: Y= None seventh digit= Ground Fault Protection: Y= None eighth digit= Load Balance: Y= None 13. Packaging 1= Standard Wood Skid; 2= Open Export Crate; 3= Totally Enclosed Export Crate; 4= Shipping Bag w/wood Skid 5= Shipping Bag Only; 6= Shipping Bag w/ Totally Enclosed Export Crate; 7= Shipping Bag w/open Export Crate; Y= None 14. Testing 1= Standard Factory Performance Test 2, 9, A, B, C, D, E, F, G, H, J, Q, S= Various Witness Tests 3, 4, 5, 6, 7, 8, K, L, M, N, P, R, T= Various Certified Performance Tests Y= None 15. Approval Listing A= ARI Approval U= UL C= Canadian UL V= ARI + UL D= Canadian ARI + UL Y= None 16. Tons Actual Tons 17. Startup Y= Export- No Startup U= Domestic Startup 7= Canadian Startup 18. Labor Warranty Y= 1 year parts & labor P= 1 year, parts only 19. Extended Warranties Y= None C= Extended 1 year parts; D= Extended 1 year parts + Labor; E= Extended 2 year parts; F= Extended 2 year parts + Labor; G= Extended 3 year parts; H= Extended 3 year parts + Labor; J= Extended 4 year parts; K= Extended 4 year parts + Labor; (L thru S apply to Compressor/Drive Train Only) L= Extended 1 year parts; M= Extended 1 year parts + Labor; N= Extended 2 year parts; O= Extended 2 year parts + Labor; P= Extended 3 year parts; Q= Extended 3 year parts + Labor; R= Extended 4 year parts; S= Extended 4 year parts + Labor 20. Refrigerant Warranty 0 thru 5= actual number of years 21. Delayed Warranty Start A= None; B= 2 mos.; C= 4 mos.; D= 5 mos.; E= 8 mos.; F= 10 mos.; G= 12 mos. 22. Pounds of Refrigerant Actual refrigerant weight 23. Rated Load Amps Actual RLA 24. Insulation first digit= Condenser & Evaporator Shell Insulation: H= ¾" Closed Cell Foam Insulation on Evaporator Shell, Suction Piping, Compressor Inlet, Motor Barrel + High Humidity 3= 1-½" Closed Cell Foam Insulation on Evap. Shell, ¾" Insulation on Suction Piping, Comp. Inlet, Motor Barrel + High Humidity Y= None second digit= Condenser & Evaporator Head Insulation: Y= None; 1= Return Heads Only; 2= Return & Connection Heads 25. Motor R= Motor Style # 0747457XX; M= Motor Style # 3502188XX; C= Motor Style #3307457XX; RPL 7000053 / Page 8
Control Box Unit Control Box Mounting Components 18 27 23 21 22 24 22 24 19 25 22 23 26 15 16 18 19 NOTE: Original design Operator Interface Panel shown. Mounting hardware is the same for all panels. Ref. Description Specification Part Qty. No. Number 15 Operator Interface Panel (OITS), Original until 5/05* 071858001 1 Cable, 7-wire single, Original until 5/05* 330367901 1 Connector Only, Original until 5/05* 330332007 1 15 Operator Interface Panel w/cables, 12 Beige 5/05 & later* 330277501 1 15 Operator Interface Panel w/vga & Serial cables, 15 Beige 5/05 & later* 330276501 1 15 Operator Interface Panel w/vga & Serial cables, 15 Black 5/05 & later* 330276502 1 Cable, 12V DC Power w/4 Pin Molex & 2 Plugs all 5/05 & later* 300040768 1 Cable, Serial all 5/05 & later* 300043345 1 Cable Kit (includes VGA & Serial cords) all 5/05 & later* 300043289 1 Power Cord w/ac Adapter all 5/05 & later* 300053912 1 16 Support Arm Assy, Beige (includes swivel pin, washers, & nut) 330815401 1 16 Support Arm Assy, Black (includes swivel pin, washers, & nut) 330815411 1 18 Block- Mount 330406501 2 19 Shelf 330329601 1 21 Screw 040499041 4 22 Washer- Plain 040500316 12 23 Washer- Lock Spring 048164812 8 24 Washer- Lock 040500213 12 25 Washer- Nylon 330366101 4 26 Nut 040499906 4 27 Screw 040499040 4 * For units built between 1/05 & 5/05 check unit in field to verify which panel is installed. Original panel had single cable, later panels have 3 cables. RPL 7000053 / Page 9
Control Box Unit Control Box Detail- Until 5/05 Diagrams 102 106 104 105 103 101 107 Modem Detail (Code 11= 2LEYPA) 3 2 16 4 10 6 5 Unit Control Detail 1 7 8 RPL 7000053 / Page 10
Control Box Unit Control Box Detail- Until 5/05 * Components Ref. Sch. Description Specification Part Qty. No. Sym. Number 1 Enclosure- No Emergency Cut-Off Switch until 2/03 330406101 1 Enclosure- With Emergency Cut-Off Switch 2/03 & later 330406102 1 2 Bracket- Switches 330329701 1 3 UTB1 Terminal Block w/rail 330407301 1 4 pc02 Controller- with Display 1 330268311 1 5 CB Circuit Breaker 5 Amp SP 735073302 1 6 Switch 125V 071995301 2 7 Serial Gateway RS 232 Code 28, digit 5= P, S 330343102 1 MODBUS Code 28, digit 5= M 330343101 1 LonWorks Code 28, digit 5= L 330343401 1 BACnet w/ms/tp Code 28, digit 5= B 350147407 1 BACnet w/ethernet Code 28, digit 5= E 350147406 1 8 Board- Distribution & Isolation with connectors 330272602 1 10 Connector 330803053 1 16 Switch- Emergency Cut-Off 735004521 1 101 Bracket- Modem Code 11= 2LEYPA 330421601 1 102 Bracket- Modem Code 11= 2LEYPA 330421701 1 103 Circuit Board- Modem Code 11= 2LEYPA 330274501 1 104 Bracket Code 11= 2LEYPA 070199207 1 105 Cord Set- Modem Code 11= 2LEYPA 330422001 1 106 Cord Set- BACnet Code 11= 2LEYPA 330421901 1 107 Serial Gateway- RS232 Code 11= 2LEYPA 330343102 1 N/S Connector- Service 330406701 1 N/S= Not Shown on diagram. * This control box was used with the original design operator interface panel (which is connected to the control box with one seven-wire cable). A new design flat screen operator interface panel can be retrofitted for use with this control box using retrofit kit part number 300040573. 1 Controller must be programmed before shipping. Unit serial number and software code (located on controller label) are required when ordering to insure proper software installation. RPL 7000053 / Page 11
Control Box MicroTech II Unit Control Box Detail- 5/05 and Later Diagrams 2 3 16 10 4 22 5 6 17 8 12 7 RPL 7000053 / Page 12
Control Box MicroTech II Unit Control Box Detail- 5/05 and Later Components Ref. Sch. Description Specification Part Qty. No. Sym. Number 2 Bracket- Switches 330329701 1 3 UTB1 Terminal Block w/rail 330407301 1 4 pc02 Controller- with Display 1 330268311 1 5 CB Circuit Breaker 5 Amp SP 735073302 1 6 Switch 125V 071995301 2 7 Serial Gateway RS 232 Code 28= 2LEYYA/2LEYSA/2LEYBA 330343102 1 MODBUS Code 28= 2LEYMA/2LEMMA 330343101 1 LonWorks Code 28= 2LEYLA 330343401 1 8 Relay 24V 330720910 1 10 Connector 330803053 1 12 Holder- Relay 330720911 1 16 Switch- Emergency Cut-Off 735004521 1 17 UCM Board- Universal Communications 330275202 1 22 PC Assy- Single Board PC 330277301 1 N/S Connector- Service 330406701 1 N/S= Not Shown on diagram. 1 Controller must be programmed before shipping. Unit serial number and software code (located on controller label) are required when ordering to insure proper software installation. RPL 7000053 / Page 13
Control Box Compressor Control Box Mounting Components Compressor Control Box Oil Pump Bracket See Detail Below 282 10 280 Compressor Control Box Back Panel 281 Ref. Description Specification Part Qty. No. Number 10 Bracket- Oil Pump 330285601 1 280 Screw 3/8-16 x 1 330366201 1 281 Spacer- Nylon.25 330366101 4 282 Washer- Lock.375 040500212 1 RPL 7000053 / Page 14
Control Box Compressor Control Box Detail Diagram 9 11 12 10 28 5 4 3 7 27 18 1 31 26 6 17 22 15 16 2 30 21 RPL 7000053 / Page 15
Control Box Compressor Control Box Detail Components Ref. Sch. Description Specification Part Qty. No. Sym. Number 1 pc02 Controller 1 330268311 1 2 T2/T3/T4 Transformer 120V- 24V 100VA 9/04 & later 330720902 3 until 9/04 330278102 3 3 OP Contactor- Oil Pump 4P 331A 24VAC Coil 9/04 & later 330720903 1 until 9/04 330278103 1 4 OL Overload- Oil Pump 48DA18AA4 735021501 1 5 Heater- Oil Pump Overload 735021577 1 6 CTB1 Terminal Block w/rail 330406202 1 7 CAP Capacitor- 60 Hz. Units 35 MFD 370V 735067401 1 CAP Capacitor- 50 Hz. Units 60 MFD 370V 735067403 1 9 CB Circuit Breaker 6A 9/04 & later 330720909 1 until 9/04 330278109 1 10 LR/CR/HR Relay 24VAC 10A 9/04 & later 330720910 3 until 9/04 330278110 3 11 Mounting Rail- Relays 9/04 & later 330720911 3 until 9/04 330278111 3 12 Springs- Relay Hold Down 330278112 3 15 Standoff- Nylon Post 330406301 10 16 SC Signal Converter Board 049264901 1 17 Guardistor Board 330343901 1 18 CTB2 Terminal Block 330406203 1 21 Board- Transducer 3 Transducers 071857701 1 22 Cover 9/04 & later 330720922 1 until 9/04 330278122 1 26 Bushing 1.5 9/04 & later 036561900 1 until 9/04 330342201 1 27 Bushing 001242600 2 28 Barrier- Electrical 330406601 1 30 Connector Kit- Transducer 330803054 1 31 Connector Kit- Controller 330803053 1 1 Controller must be programmed before shipping. Unit serial number and software code (located on controller label) are required when ordering to insure proper software installation. RPL 7000053 / Page 16
Control Box Cables Diagram 888 403 426 402 402A 17 552 559 995 998 350 551 557 750 748 406 552 RPL 7000053 / Page 17
Control Box Sensors Diagram 748 100 552 557 559 558 557 748 100 102 557 750 100 60 551 220 555 552 80 552 557 750 100 552 350 60 552 352 Compressor Control Sensor Application Unit Control Sensor Application Sensor CS01 CS02 CS03 CS04 CS05 CS06 CS07 CS08 CS09 CS10 Application Oil Sump Pressure Oil Feed Gauge Pressure Evap. Refrigerant Pressure Oil Sump Temperature Compressor Suction Temp. Cond. Refrigerant Pressure Compressor Discharge Temp. % Compressor Amps (Starter) Oil Feed Temperature Evap. Leaving Water Temp. Sensor US02 US03 US04 US05 US09 US10 Application Evaporator Entering Water Temp. Condenser Entering Water Temp. Condenser Leaving Water Temp. Liquid Line Temp. Heat Recovery Entering Water Temp. Heat Recovery Leaving Water Temp. RPL 7000053 / Page 18
Control Box Cables and Sensors Components Ref. Sch. Description Specification Part Qty. No. Sym. Number 17 Cable- Operator Interface Panel 330367901 7 1 Connector Only 330332007 1 60 Conduit Fitting.375" 735048013 7 80 Conduit Fitting.250" 735048015 1 100 Valve Core 026541100 2 102 Sensor Well- Oil Supply Tube 070809042 1 220 Sensor Well until 9/02 070809003 1 Sensor Well 4 9/02 to 3/03 047441511 1 Sensor Well 6 3/05 & later 330198002 1 350 CS04 Sensor- Oil Sump 330198001 1 352 Cable- CS04 Sensor 330418501 1 402 Cable, Empty- Comp Heater 1 330006706 1 402A Cable, Empty- Comp Heater 1 330006707 1 403 Cable- Oil Pump Heater 1 330006741 1 406 Cable- Solenoids 330287403 2 426 Cable- Starter 2 070829981 1 551 CS05 Sensor until 3/03 073007302 5 1 Sensor 3/03 to 3/05 330198001 5 1 Sensor 3/05 & later 330198003 6 1 552 3 Sensor 073007202 8 555 Cable- CS05 Sensor 3/03 & later 330418501 1 557 Cable- Transducer 074667502 4 558 HP1 Switch- High Pressure until 6/03 074796302 1 HP1 Switch- High Pressure 6/03 & later 074796301 1 559 Cable- High Pressure Switch 1 070829997 1 748 CS02/06 Transducer- High 410 PSI 071568601 2 750 CS01/03 Transducer- Low 132 PSI 071568501 2 888 Cable- Guardistor 070829989 1 995 plan Cable- plan between Unit & Compr Controller 034248800 ** 998 Cable- Power between Unit & Compr Controller 330406402 15 ft. N/S Boot- Transducer until 5/03 071583301 4 N/S= Not Shown on diagram. ** There are two cables. Each made from 15 feet of the above listed p/n. 1 Cables contain 90 fitting p/n 000916900 and Anti- Short bushing p/n 047356401. 2 See Starter section for all starter- related cables and mounting components. 3 CS07, CS08, CS09, CS10, US02, US03, US04, US05. 4 Paste for sensor well is p/n 735026315. Well was used with sensor p/n 073007302 until 3/03 when new style temperature sensor [CS05] p/n 330198001 was added. 5 The CS05 Sensor change resulted in a relocation of the sensor. The new sensor is located in the inlet cone (illustrated in the diagram). The older sensor (before 3/03) was located in the suction elbow. 6 Beginning 3/05 the CS05 sensor was redesigned to use a well. The location remained the same. From 3/03 to 3/05 no well was used. 7 This cable was used with the original operator interface panel. The new flat screen panel uses a VGA cable & a serial cable which come with the panel. RPL 7000053 / Page 19
Starter Cables, Mounting Components 60 51 100 100 Shroud Mounting Top View 426 317 50 42 41 43 Angle Bracket to Starter 40 42 41 42 20 50 40 41 50 Angle Bracket to Starter Bracket Ref. Description Specification Part Qty. No. Number 20 Angle Bracket 330107901 4 40 Screw.50 X 1.5 735033847 16 41 Washer- Plain.50 ZPS 040500311 32 42 Washer- Lock.50 ZPS 048164814 16 43 Nut.50-13 735029505 16 50 Washer- Lock Grounding 040500213 32 51 Washer- Lock.19 ZPS 040500206 4 60 Screw.19-24 x.50 046093802 4 100 Shroud- Terminals 074865604 1 317 Bracket- Starter Mounting 350257302 4 426 Cable: Starter- to- MicroTech II Control Box 070829981 1 N/S Cable: Starter- to- Compressor Terminal 1 074867510 1 348 RLA Max. Motors 074867511 1 399 RLA Max. Motors 074867512 1 460 RLA Max. Motors 074867513 1 696 RLA Max. Motors 074867511 2 N/S= Not Shown on Diagram. RPL 7000053 / Page 20
Liquid Line Expansion Valve, Ball Valve, Sight Glass, King Valve, Flanges, Gaskets, O'Rings, Pilot Valve Sensor Well, Tubing Diagram 314 313 312 Pilot Valve Bulb Detail 303 308 338 304 Pressure Connector (ref. # 304) Detail 180 300 140 101 100 82 80 81 307 306 60 41 200 220 40 43 221 222 330 331 End View King Valve to Condenser Detail 254 251 241 240 242 20 21 260 261 262 41 263 22 Condenser 23 24 252 253 RPL 7000053 / Page 21
Liquid Line Expansion Valve, Ball Valve, Sight Glass, King Valve, Flanges, Gaskets, O'Rings, Pilot Valve Sensor Well, Tubing Components Ref. Description Specification Part Qty. No. Number 20 Adapter 070760902 1 21 Flange 071992101 1 22 Gasket- Flange 735073402 1 23 Screw 735033967 4 24 Strainer 070977801 1 40 Tube 350225608 1 41 Elbow- 90 041117113 2 43 Tube 350225624 1 60 Tube- Main Liquid Line 1 350146461 1 80 Flange- Evaporator Inlet 070761402 1 81 O'Ring- Evaporator Inlet Flange 735043674 1 82 Screw- Evaporator Inlet Flange 735033864 4 100 O'Ring 735073633 1 101 Screw.75 x 3.0 735033878 4 140 Expansion Valve- Main 550 Ton (Code 10= QB) 2 330848009 1 Expansion Valve- Main 800 Ton (Code 27= PB) 2 330848005 1 180 Tube until 10/02 350146403 1 Tube 10/02 & later 070205032 1 200 Pilot Expansion Valve 735048665 1 220 Tube- Pilot Valve 330183501 1 221 Reducer.875ODS x.375ods 041116517 1 222 Tube- Pilot Valve 330184001 1 240 Bracket- Tube Support 330189301 1 241 Clamp- Tube 040971308 1 242 Screw.19-24 x.50 046093802 1 251 Valve- Main Liquid (King) 3.00" 735039807 1 252 Screw- King Valve.62 x 5.0 735033957 4 253 Gasket- King Valve 070199104 1 254 Cap- King Valve 071556902 1 260 Strainer 735030501 1 261 Tube 070208020 1 262 Ball Valve 330286004 1 263 Tube- Pilot Valve 330184101 1 300 Tee Assembly 735061434 1 303 Elbow- Pilot Bulb to Sensor Well 90 001276600 1 304 Pressure Connector 070811202 1 306 Fitting- Sleeve Orifice 070789328 1 307 Fitting- Nut Orifice 070789327 1 308 Flare Nut 3 000028600 1 312 Valve Core 3 026541100 1 313 Schrader Valve 3 071100801 1 314 Schrader Valve Cap 3 032943500 1 330 Valve- Shutoff.375" Flare 735039907 1 Cap for Shutoff Valve 071556909 1 331 Flare Cap 000540900 1 338 Sensor Well- Pilot Valve located at top of evaporator 735946401 1 1 Tube contains one (1) each schrader valve p/n 071100801, valve cap p/n 032943500, valve core 026541100, sight glass saddle 330743301, and sight glass cap 330508701. 2 Parts detail on following page. 3 Part of pressure connector assembly (ref. #304). RPL 7000053 / Page 22
Liquid Line Expansion Valve Detail 157 Expansion Valve Detail 330848009/ 330848005 145 149 146 160 153 142 152 153 147 144 151 156 142 143 150 155 152 154 158 148 141 Ref. Description Part Qty. No. Number Valve Assy- 550 Ton 330848009 Valve Assy- 800 Ton 330848005 141 Body 330501801 1 142 Cap 330548801 1 143 Spring 735036937 1 144 Stop 072960101 1 145 Stem 072960203 1 146 Pin-.69 x.16 735038019 1 147 O'Ring 735043662 2 148 Retainer 330501501 1 149 Washer 735043447 1 150 Piston 550 Ton 330501702 1 800 Ton 330501701 1 151 Seal Ring 736017602 2 152 O'Ring 735043674 1 153 Screw 735033927 6 154 Pin-.88 x.25 735038038 1 155 Fitting- Orifice 070789326 1 156 Quad Ring 330549201 2 157 Cap 071556916 1 158 Screw 735033233 1 159 Seal- Washer 735038309 2 160 Washer- Plain 040500308 6 RPL 7000053 / Page 23
Condenser & Evaporator Valves Relief Valves, Shutoff Valves 331 330 20 22 331 330 331 330 20 22 21 Ref. Description Specification Part Qty. No. Number 20 Elbow 735031239 2 21 Valve- Shut Off 1" NPT 735039977 1 22 Valve- Relief 200 PSI 735045817 3 330 Valve- Shutoff.625" 735039929 3 Cap for Shutoff Valve 071556909 3 331 Flare Cap.625" 073243901 3 RPL 7000053 / Page 24
Insulation Hi Humidity, Double Hi Humidity D A B C Ref. Description Specification Part No. Number Qty. A Evaporator Insulation Single ¾" Layer 047662050 158 sqft Double 1-½" Layer 047662050 305 sqft B Evaporator Head Insulation Single ¾" Layer 047662050 17 sqft Double 1-½" Layer 047662050 36 sqft C Condenser Head Insulation Single ¾" Layer 047662050 13 sqft Double 1-½" Layer 047662050 28 sqft D Suction Line 047662050 56 sqft RPL 7000053 / Page 25
Condenser Nomenclature Nameplate used until 8/03 Nameplate used 8/03 and later Model Number- Condenser C 22 12 B L 2 R A Condenser Type C= Standard S= Split Head Nozzle Configuration A= Victaulic Condenser Diameter 22 Condenser Length (in feet) 12 Condenser Tube Count B= 300 Inlet Nozzle Location L= Left R= Right Condenser Tube Type L=.025 Wall Number of Water Passes 2 5 5 A 01750 01 Engineering Revision Plant Identification 5= Staunton Serial Number Year of Manufacture 2= 2002 3= 2003 4= 2004 5= 2005 6= 2006 7= 2007 Serial Number- Condenser Month of Manufacture A= January G= July B= February H= August C= March J= September D= April K= October E= May L= November F= June M= December RPL 7000053 / Page 26
Condenser Sight Glass, Flanges, Heads, Gaskets, Tubes Diagram & Components Return Head*** 355 Front View Shut Off Valve** 355 Connection Head*** Shut Off Valve* End View King Valve* King 110 Valve* 116 100 *See Liquid Line Section ** See Evap & Cond. Relief Valve Section *** To identify Head part numbers, contact Daikin Applied with the unit model and serial number. Ref. Description Specification Part Qty. No. Number 100 Tubes 330441408 300 110 Sight Glass 350229501 1 116 Flange- Liquid Line 071580601 1 355 Gasket 1 070304604 2 N/S= Not Shown on Diagram. 1 The Gaskets for Condenser heads are sold in two parts. The gasket itself is the rim that fits between the head and the Condenser's tube sheet. 2-pass heads use the gasket plus a U-channel that is glued to the rim and fits over the baffles that separate the passes. Each connection head gasket requires 3' of U-Channel part number 070189802. The U-Channel adhesive is part number 735026371. RPL 7000053 / Page 27
Evaporator Nomenclature Nameplate used until 8/03 Nameplate used 8/03 and later Model Number- Evaporator E 26 12 B E 2 R A Evaporator Evaporator Diameter 26 Evaporator Length (in feet) 12 Evaporator Tube Count B= 226 Nozzle Configuration A= Victaulic Inlet Nozzle Location L= Left R= Right Number of Water Passes 2 Evaporator Tube Type E=.025 Wall Thickness 5 4 A 01750 01 Engineering Revision Plant Identification 5= Staunton Serial Number Year of Manufacture 2= 2002 3= 2003 4= 2004 5= 2005 6= 2006 7= 2007 Serial Number- Evaporator Month of Manufacture A= January G= July B= February H= August C= March J= September D= April K= October E= May L= November F= June M= December RPL 7000053 / Page 28
Evaporator Sight Glass, Liquid Line Flange, Heads, Gaskets, Tubes Diagram & Components Return Head*** Sensor Well* Shut Off Valve** 355 355 Connection Head*** 116 *See Liquid Line Section ** See Evap & Cond. Relief Valve Section *** To identify Head part numbers, contact Daikin Applied with the unit model and serial number. 108 Shut Off Valve** 110 Ref. Description Specification Part Qty. No. Number N/S Tubes 073238590 226 108 Block Off- HGBP Service Tool 330616401 1 110 Sight Glass 350229501 1 116 Flange- Liquid Line 350236201 1 355 Gasket 1 070304605 2 N/S= Not Shown on diagram. 1 The Gaskets for Evaporator heads are sold in two parts. The gasket itself is the rim that fits between the head and the Evaporator's tube sheet. 2-pass heads use the gasket plus a U-channel that is glued to the rim and fits over the baffles that separate the passes. Each connection end head gasket requires 3' of U-Channel part number 070189802. The U-Channel adhesive is part number 735026371. RPL 7000053 / Page 29
Compressor Nomenclature Model Number- Compressor CE 079 L AZ 35 B Compressor Impeller Size 079= 7.9" Impeller Type L Motor Voltage See Compressor Section Motor Table Motor Horsepower See Compressor Section Motor Table Gear Ratio Code See Compressor Section Gear Table Always 0 Unit G.O. No. Style Number- Compressor 0 923456010 FR01 Motor Style Number Compressor The motor style number is the part number. See the following pages for list of motor, stator & rotor/shafts. Serial Number- Compressor 5 5 A 01750 01 Plant Identification 5= Staunton Engineering Revision Year of Manufacture 2= 2002 3= 2003 4= 2004 5= 2005 6= 2006 7= 2007 etc. Serial Number Month of Manufacture A= January G= July B= February H= August C= March J= September D= April K= October E= May L= November F= June M= December RPL 7000053 / Page 30
Compressor Mounting Brackets and Hardware Compressor 302 50 61 62 302 60 Ref. Description Specification Part Qty. No. Number 50 Washer- Lock.625 ZPS 040500214 4 60 Screw.625 x 2.0 735033862 4 61 Washer- Plain.625 ZPS 040500312 4 62 Washer- Lock.625 ZPS 048164815 4 302 Bracket- Compressor 350303503 1 RPL 7000053 / Page 31
Compressor 4- Way SA/SB Solenoid Valve & Tubing 406 401 409 410 403 417 402 408 Vane Close Switch Port 407 400 406 405 404 418 421 405 419 404 422 420 406 Ref. Description Specification Part Qty. No. Number 400 Differential Pressure Switch 071896001 1 401 4 Way Solenoid Valve SA/SB 073221501 1 402 Bulkhead Connector 070789301 2 408 Elbow- 45 Straight Thread 070789337 1 Installation Kit- 4 Way Valve 070789101 Kit includes: 403 Nut 070789302 2 404 Tee 070789303 2 405 Straight Connector 070789304 2 406 Elbow Connector 070789306 3 407 Swivel- Straight Thread 070789336 1 409 Bolt- Mounting Bracket 070789002 2 410 Mounting Bracket- 4 Way Valve 070789003 1 417 Tube Assembly- Supply 070789102 1 418 Drain Tube Assembly 070789103 1 419 Tube Assembly- Return 070789106 1 420 Tube Assembly- Vane Open 070789105 1 421 Tube Assembly- Vane Close 070789104 1 422 Switch Tube Assembly 070789107 1 RPL 7000053 / Page 32
Compressor Motor Drain Line, Motor Cooling Line, Liquid Injection Diagram 422 421 424 420 423 442 520 440 444 442 480 460 500 443 Tube Detail (ref. # 440) 221 220 222 240 Liquid Injection 501 242 260 241 Motor Cooling Line 280 361 300 360 320 Motor Drain Line 340 42 41 40 60 Motor Drain Connection Detail 20 21 81 80 100 24 RPL 7000053 / Page 33
Ref. Description Specification Part Qty. No. Number 20 Fitting- Sleeve 070789315 1 21 Fitting- Nut 070789309 1 24 Tube- Motor Drain 350260901 1 40 Flange- 2 Bolt 074614801 1 41 O-Ring 2 Bolt Flange 735073629 1 42 Screw 2 Bolt Flange 735033846 2 60 Tube- Motor Drain 330194801 1 80 Filter Drier 021057422 1 81 Bushing- Filter Drier 1.625 ODM x 1.375 ODS 041116717 2 100 Tube, Motor Drain- Bottom 330195201 1 220 Flange 735414015 1 221 O-Ring 070194913 1 222 Screw 735017345 2 240 Tube- Motor Cooling 330184501 1 241 Tube- Motor Cooling 330184401 1 242 Tube- Motor Cooling 1 350146425 1 260 Valve- Check 735040332 1 280 Filter Drier 735028827 1 300 Tube Assembly 1 350146430 1 320 Valve- Ball until 10/03 036526904 1 Valve- Ball 10/03 to 4/10 330286054 1 Valve- Ball 4/10 & later 330286004 1 340 Tube- Motor Cooling 330182801 1 360 Clamp- Filter Drier 074674101 1 361 Screw- Drier Clamp.25 x.75 735032782 1 420 Flange 070275701 1 421 O'Ring- Flange 735043687 1 422 Screw- Flange 735033846 2 423 Tube 330108801 1 424 Reducer 041116518 1 440 Tube Assembly 350361701 1 442 Tube 070209028 1 443 Strainer 735030528 1 444 Solenoid Valve 735048469 1 460 Tube 330196101 1 480 Valve- Ball 330286005 1 500 Tube 330196301 1 501 Tube 330196401 1 520 Insulation 735046105 1 ft. 1 The tube assembly (all sizes) has a schrader valve body p/n 071100801, core p/n 026541100 and cap p/n 032943500. Compressor Motor Drain Line, Motor Cooling Line, Liquid Injection Components RPL 7000053 / Page 34
Compressor Suction and Discharge Lines Suction Victaulics and Pipes, Seals Discharge Nozzle, Flanges, Check Valve Diagram & Components 881 884 885 91A 91 90 88 86 80 84 820 880 882 89 89A 128 22 127 125 126 130 Ref. Description Specification Part Qty. No. Number 22 Nut- Discharge Check Valve.75-10 735029608 16 80 Pipe- Suction P040SFBEAA 1 84 Elbow 735031364 1 86 Pipe- Suction P028SFEEAA 1 88 Elbow 735031329 1 89 Coupling, Victaulic- 10" 1 070193902 1 89A Gasket- 10" Coupling 070194002 1 90 Pipe- Suction P030SFBEAA 1 91 Coupling, Victaulic- 10" 1 070193902 1 91A Gasket- 10" Coupling 070194002 1 125 Valve- Discharge Check 8" 735040319 1 126 Gasket- Discharge Check Valve 070199012 2 127 Flange 735031835 1 128 Screw- Discharge Check Valve 735033974 8 130 Pipe, Discharge P106RHAAAA 1 820 Nozzle- Discharge 070531701 1 880 Valve- Shutoff 735039947 1 881 Tee 070229302 1 882 Cap 001106100 1 884 Coupling 735044212 1 885 O'Ring- Coupling 735073639 1 1 Coupling includes gasket. RPL 7000053 / Page 35
Compressor Section Assembly Main Sections, O'Rings, Screws Motor Housing 801 803 867 857 865 Front End Gear Housing Ref. Description Specification Part Qty. No. Number 801 Screw.37 x 1.75 735017347 36 803 Screw- Gear Housing.37 x 1.75 735017347 20 857 Pin- Alignment 735068009 2 865 O'Ring 735043626 1 1 867 O'Ring 735073648 2 1 1 Included in 15" Motor Housing O'Ring Kit p/n 350306205K. 2 Included in Gear Housing O'Ring Kit p/n 350306204K. RPL 7000053 / Page 36
Compressor Front End Inlet Section Vanes, Piston, Cone, Seals 276 275 271 Cone 3/03 & later (Plug/O'Ring added) 203 223 220 220 236 202 224 222 221 203 226 226C 260 204 202 220 226B 226A 205 236 Cone before 3/03 Ref. Description Specification Part Qty. No. Number 202 Quad Ring 735073407 1 2 203 Quad Ring 735073408 1 2 204 Quad Ring 735073409 1 1 205 O'Ring 735073647 1 2 220 Cone 350145201 2 1 Screw- Cone 735036478 4 Dowel Pin- Cone.125 x.25 735038036 2 221 Piston 071459301 1 222 Seal- Impeller 735233101 1 223 Ring- Retainer 735235702 1 224 Ring- Retainer 735049818 1 226 Vane Assembly Includes Vane, Washer, Bearing 070796611 11 226A Vane Only 070529201 11 226B Bearing Only 735017205 11 226C Washer Only 735043456 11 236 Screw.37 X 1.5 735017346 16 260 Plug w/o'ring 3/03 & later 735017102 1 271 Volute 070551201 1 275 Diffuser- Front 073188001 1 276 Screw.25 x.625 735034976 4 1 Included in Front End O'Ring Kit p/n 350306202K. 2 The inlet cone was modified 3/03. Sensor CS05 is now inserted in this cone (prior to 3/03 it was inserted in the suction elbow). RPL 7000053 / Page 37
Compressor Main Gear Train Impeller, Volute, Diffuser, Oil Filter, Spin Down, Low Speed Gear, Low Speed Bearings, Gear Housing and Seals Diagram & Components 507 509 550 532 525 526 535 571 501 524 549 551 552 523 521 568 527A 593 544 575 534 1 562 574 554 533 528 506 536 574 511 592 527B 561 500 527C 595 571 532 550 594 569 564 520 591 596 505 588 Ref. Description Specification Part Qty. No. Number 1 High Speed Assembly Details in following section 500 Impeller 7.9 in. diameter 350145302 1 501 Rotor & Shaft Assembly see Motor Section 505 Gear- Low Speed see gear table after HS Assy section 506 Pipe Plug.375 049760903 1 507 Brass Weight.5 070224601 5 509 Brass Weight.25 070224603 3 511 Pin.50 x.06 735038031 1 520 Pin.38 x.12 735038023 2 RPL 7000053 / Page 38
Compressor Main Gear Train Impeller, Volute, Diffuser, Oil Filter, Spin Down, Low Speed Gear, Low Speed Bearings, Gear Housing and Seals Components, Continued Ref. Description Specification Part Qty. No. Number 521 Housing- Gear until 2/ 05 070551003 1 Housing- Gear 2/ 05 & later 070551005 1 523 Seal 735234313 1 524 Screw- Cover.25 x.75 735017314 8 525 Cover- Bearing 759911301 1 526 Retaining Ring 735049880 1 527A Screw- High Speed Assembly.25 x 1.00 735017316 5 527B Screw- Diffuser.25 x 1.00 735017316 4 527C Screw- Thrust.25 x 1.00 735017316 6 528 Spring- Spin Down 735036924 1 532 Cover- Oil Filter/Spin Down 744024302 2 533 Piston- Spin Down 744024802 1 534 Screw- LS Bearing #8 x.50 735034928 1 535 Bearing, Low Speed- Motor End 070477701 1 536 Bearing, Low Speed- Gear End 070477601 1 544 Diffuser 071459101 1 549 Spring- Oil Filter 735036918 1 550 Screw- Oil Filter/Spin Down Covers.25 x 2.0 735017320 12 551 Oil Filter 735006904 1 552 Valve- Check 735040335 1 554 Pipe Plug.125 049760901 1 561 O'Ring 735073693 3 2 562 O'Ring 735043635 1 1 564 O'Ring 735073658 1 1 568 O'Ring 735043673 2 4 569 O'Ring 735043640 1 1 571 Gasket- Oil Filter/Spin Down 070199009 2 574 O'Ring 735043650 1 4 575 Gasket- Cover 071294601 1 588 Screw- Gear Lock Plate.37 x 1.7 735017347 6 591 Lee Plug 735078306 1 592 Spacer 070278401 1 593 Plate- Thrust 070282201 1 594 Bearing- Low Speed Thrust 070475303 1 595 Plate- Gear Lock 744022101 1 596 Cover- Thrust 070513801 1 1 This O'Ring is included in the Gear Housing O'Ring Kit 350306204K. 2 This O'Ring is included in the High Speed Assembly O'Ring Kit 350306203K. 3 This O'Ring is included in the Front End Assembly O'Ring Kit 350306202K. RPL 7000053 / Page 39
Compressor High Speed Assembly Pinion, Thrust Pump, High Speed Bearings, Seals Diagram 429 416 469 423 413 415 421 421 460 418 466 468 Original Design: Until 10/03 (italicized parts have changed and are no longer available. If any one of these are required, all must be retrofitted) 414 469 438 463 455 466 437 410 426 429 416 427 421 415 421 421 460 418 466 Current Design: 10/03 and later 413 414 466 469 469 438 463 455 466 437 NOTE: In late September, 2003 the rear high speed assembly was redesigned. Both designs are shown for reference, however only the current design may be used for replacement parts. The parts involved in the redesign are indicated in the Original Design diagram with italicized reference bubbles. Original and new design affected (italicized) parts DO NOT interchange, and older design parts are no longer available. Replacement of any of the affected parts on a unit built prior to 10/03 requires retrofitting the assembly with ALL redesigned parts. 410 426 427 RPL 7000053 / Page 40
Compressor High Speed Assembly Pinion, Thrust Pump, High Speed Bearings, Seals Components Ref. Description Specification Part Qty. No. Number 410 Gear- High Speed see gear table below 413 Bearing- Inactive Thrust 070776902 1 1 414 Bearing- Active Thrust 350093502 1 1 416 Cover- Thrust 074763402 1 1 418 Disc- Expansion 072288201 1 415 Thrust Pump 071447401 1 421 Pin until 10/03 735038031 2 Pin 10/03 & later 735038039 1 5 423 Screw 3 3 426 Bearing- High Speed Front 071409801 1 427 Screw.25 x.62 735017313 4 429 Screw.25 x 1.2 735017317 4 437 Housing- High Speed Gear 070551402 1 1 438 Bearing- High Speed Rear 070703502 1 1 455 O'Ring 735073642 2 1 460 O'Ring until 10/03 735073607 1 O'Ring 10/03 & later 070194987 1, 2 1 463 O'Ring 735073657 2 2 466 Plug- Pipe 049760902 4 469 O'Ring 735043640 2 2 N/S= Not shown on diagram. 1 The part numbers listed apply to the current design numbers. If retrofitting an original design High Speed Assembly all of these parts must be ordered (as well as any additional O'Rings required for general disassembly/ assembly). 2 This O'Ring is included in the High Speed Assembly O'Ring Kit 350306203K. 3 The original inactive thrust bearing was attached to the thrust cover using these three screws (p/n 735034928). These screws are no longer required in this assembly. The bearing is now locked in place using three roll pins (reference # 421). Gears- High Speed (Pinion) & Low Speed (Bull) Gear High Speed Low Speed Code Pinion Gear Bull Gear A2 071889658 776123258 AY 071889659 776123259 AZ 071889660 776123260 O'Ring Kits Application Front End (IGV) High Speed Assembly Main Gear Housing Motor Housing- 15" Kit Number 350306202K 350306203K 350306204K 350306205K RPL 7000053 / Page 41
Compressor Motor Section Housing, Sight Glass, Motor, Terminals, Seals, Hardware Diagram 775 721 744 779 Guardistor Terminal Detail 741 751 753 773 789 787 720 712 776 777 782 783 710 711 731 701 732 Terminal Connection Detail 731 734 735 733 RPL 7000053 / Page 42
Compressor Motor Section Housing, Sight Glass, Motor, Terminals, Seals, Hardware Components Ref. Description Specification Part Qty. No. Number 701 Stator 1 see motor tables on following pages 710 Gasket- Block Off Flange 070199011 1 711 Screw- Block Off Flange 735017345 2 712 Flange- Block Off 4 Service Tool 735055221 1 720 Housing- 15" Motor 074891702 1 721 Cover, End- Motor Housing 070677801 1 731 Terminal- Motor 074608102 5 6 732 Screw- Terminal.37 x 1.2 735033233 6 733 Nut- Terminal.37-16 040499906 6 734 Washer, Flat- Terminal 040500316 12 735 Washer, Lock- Terminal 048164812 6 741 O'Ring- End Cover 735043638 2 1 744 O'Ring 735073635 2 1 751 Box- Electrical 330763801 1 753 Washer- Lock 048164806 3 4 773 Screw #10 x.62 735036446 3 4 775 Sight Glass- End Cover 015997816 2 776 Screw- End Cover.37 x 1.5 735033435 16 777 Washer, Lock- End Cover 048164812 16 779 Terminal- 4 Pin 070260802 1 782 Dowel 735068004 1 783 Plug w/o'ring 735017101 1 787 Orifice Fitting Motor Drain Conn. 070789304 1 789 Cap- Orifice Fitting Service Tool 070789311 1 1 See Gear Housing Section for location of rotor/shaft assembly. 2 This O'Ring is included in the 15" Motor Housing Assembly O'Ring Kit 350306205K. 3 Units built prior to 2/03 used a ½" screw p/n 735036445 and no lock washers. 4 Motor Cooling line flange connects here. 5 Part number 074608103 may also be used. RPL 7000053 / Page 43
Compressor Motors Style 0747457XX- Stators, Rotor/Shaft Assembly Ref. Motor Motor Motor Motor Stator Rotor/ No. Code 1 Voltage H.P. P.N. Part No. Shaft Assy 2 701 23U 380/60 230 074745759 074745809 074855752 23N 200/60 230 074745761 074745811 074855752 23B 208/60 230 074745761 074745811 074855752 23P 220/60 230 074745762 074745812 074855752 23V 230/60 230 074745762 074745812 074855752 23W 240/60 230 074745762 074745812 074855752 23A 440/60 230 074745763 074745813 074855752 23R 460/60 230 074745763 074745813 074855752 23S 480/60 230 074745763 074745813 074855752 23D 575/60 230 074745764 074745814 074855752 23E 220/50 242 074745765 074745815 074855753 23Y 346/50 242 074745766 074745816 074855753 29U 380/60 290 074745766 074745816 074855753 23H 440/50 242 074745767 074745817 074855753 29N 200/60 290 074745768 074745818 074855753 29B 208/60 290 074745768 074745818 074855753 29P 220/60 290 074745769 074745819 074855753 29V 230/60 290 074745769 074745819 074855753 29W 240/60 290 074745769 074745819 074855753 23F 380/50 242 074745770 074745820 074855753 23G 400/50 242 074745770 074745820 074855753 23K 415/50 242 074745770 074745820 074855753 29A 440/60 290 074745770 074745820 074855753 29R 460/60 290 074745770 074745820 074855753 29S 480/60 290 074745770 074745820 074855753 29D 575/60 290 074745771 074745821 074855753 29E 220/50 292 074745772 074745872 074855754 29Y 346/50 292 074745773 074745873 074855754 35U 380/60 350 074745773 074745873 074855754 29H 440/50 292 074745774 074745874 074855754 35N 200/60 350 074745775 074745875 074855754 35B 208/60 350 074745775 074745875 074855754 35P 220/60 350 074745776 074745876 074855754 35V 230/60 350 074745776 074745876 074855754 35W 240/60 350 074745776 074745876 074855754 29F 380/50 292 074745777 074745877 074855754 29G 400/50 292 074745777 074745877 074855754 29K 415/50 292 074745777 074745877 074855754 35A 440/60 350 074745777 074745877 074855754 35R 460/60 350 074745777 074745877 074855754 35S 480/60 350 074745777 074745877 074855754 35D 575/60 350 074745778 074745878 074855754 35E 220/50 333 074745779 074745879 074855755 35Y 346/50 333 074745780 074745880 074855755 40U 380/60 400 074745780 074745880 074855755 1 Digits 9, 10, 11 in compressor model number. 2 Rotor and Low Speed Shaft shrunk fit together. RPL 7000053 / Page 44
Compressor Motors Style 0747457XX- Stators, Rotor/Shaft Assembly Continued Ref. Motor Motor Motor Motor Stator Rotor/ No. Code 1 Voltage H.P. P.N. Part No. Shaft Assy 2 701 35H 440/50 333 074745781 074745881 074855755 40N 200/60 400 074745782 074745882 074855755 40B 208/60 400 074745782 074745882 074855755 40P 220/60 400 074745783 074745883 074855755 40V 230/60 400 074745783 074745883 074855755 40W 240/60 400 074745783 074745883 074855755 35F 380/50 333 074745784 074745884 074855755 35G 400/50 333 074745784 074745884 074855755 35K 415/50 333 074745784 074745884 074855755 40A 440/60 400 074745784 074745884 074855755 40R 460/60 400 074745784 074745884 074855755 40S 480/60 400 074745784 074745884 074855755 40D 575/60 400 074745785 074745885 074855755 40Q 416/60 400 074745786 074745886 074855755 1 Digits 9, 10, 11 in compressor model number. 2 Rotor and Low Speed Shaft shrunk fit together. RPL 7000053 / Page 45
Compressor Motors Style 3502188XX- Stators, Rotor/Shaft Assembly Ref. Motor Motor Motor Motor Stator Rotor/ No. Code 1 Voltage H.P. P.N. Part No. Shaft Assy 2 701 23U 380/60 230 350218859 350218909 350283252 23N 200/60 230 350218861 350218911 350283252 23B 208/60 230 350218861 350218911 350283252 23P 220/60 230 350218862 350218912 350283252 23V 230/60 230 350218862 350218912 350283252 23W 240/60 230 350218862 350218912 350283252 23A 440/60 230 350218863 350218913 350283252 23R 460/60 230 350218863 350218913 350283252 23S 480/60 230 350218863 350218913 350283252 23D 575/60 230 350218864 350218914 350283252 23E 220/50 242 350218865 350218915 350283253 23Y 346/50 242 350218866 350218916 350283253 29U 380/60 290 350218866 350218916 350283253 23H 440/50 242 350218867 350218917 350283253 29N 200/60 290 350218868 350218918 350283253 29B 208/60 290 350218868 350218918 350283253 29P 220/60 290 350218869 350218919 350283253 29V 230/60 290 350218869 350218919 350283253 29W 240/60 290 350218869 350218919 350283253 23F 380/50 242 350218870 350218920 350283253 23G 400/50 242 350218870 350218920 350283253 23K 415/50 242 350218870 350218920 350283253 29A 440/60 290 350218870 350218920 350283253 29R 460/60 290 350218870 350218920 350283253 29S 480/60 290 350218870 350218920 350283253 29D 575/60 290 350218871 350218921 350283253 29E 220/50 292 350218872 350218972 350283254 29Y 346/50 292 350218873 350218973 350283254 35U 380/60 350 350218873 350218973 350283254 29H 440/50 292 350218874 350218974 350283254 35N 200/60 350 350218875 350218975 350283254 35B 208/60 350 350218875 350218975 350283254 35P 220/60 350 350218876 350218976 350283254 35V 230/60 350 350218876 350218976 350283254 35W 240/60 350 350218876 350218976 350283254 29F 380/50 292 350218877 350218977 350283254 29G 400/50 292 350218877 350218977 350283254 29K 415/50 292 350218877 350218977 350283254 35A 440/60 350 350218877 350218977 350283254 35R 460/60 350 350218877 350218977 350283254 35S 480/60 350 350218877 350218977 350283254 35D 575/60 350 350218878 350218978 350283254 35E 220/50 333 350218879 350218979 350283255 35Y 346/50 333 350218880 350218980 350283255 40U 380/60 400 350218880 350218980 350283255 1 Digits 9, 10, 11 in compressor model number. 2 Rotor and Low Speed Shaft shrunk fit together. RPL 7000053 / Page 46
Compressor Motors Style 3502188XX- Stators, Rotor/Shaft Assembly Continued Ref. Motor Motor Motor Motor Stator Rotor/ No. Code 1 Voltage H.P. P.N. Part No. Shaft Assy 2 701 35H 440/50 333 350218881 350218981 350283255 40N 200/60 400 350218882 350218982 350283255 40B 208/60 400 350218882 350218982 350283255 40P 220/60 400 350218883 350218983 350283255 40V 230/60 400 350218883 350218983 350283255 40W 240/60 400 350218883 350218983 350283255 35F 380/50 333 350218884 350218984 350283255 35G 400/50 333 350218884 350218984 350283255 35K 415/50 333 350218884 350218984 350283255 40A 440/60 400 350218884 350218984 350283255 40R 460/60 400 350218884 350218984 350283255 40S 480/60 400 350218884 350218984 350283255 40D 575/60 400 350218885 350218985 350283255 40Q 416/60 400 350218886 350218986 350283255 1 Digits 9, 10, 11 in compressor model number. 2 Rotor and Low Speed Shaft shrunk fit together. RPL 7000053 / Page 47
Compressor Motors Style 3307457XX- Stators, Rotor/Shaft Assembly Ref. Motor Motor Motor Motor Stator Rotor/ No. Code 1 Voltage H.P. P.N. Part No. Shaft Assy 2 701 23U 380/60 230 330745759 330745809 330746052 23N 200/60 230 330745761 330745811 330746052 23B 208/60 230 330745761 330745811 330746052 23P 220/60 230 330745762 330745812 330746052 23V 230/60 230 330745762 330745812 330746052 23W 240/60 230 330745762 330745812 330746052 23A 440/60 230 330745763 330745813 330746052 23R 460/60 230 330745763 330745813 330746052 23S 480/60 230 330745763 330745813 330746052 23D 575/60 230 330745764 330745814 330746052 23E 220/50 242 330745765 330745815 330746053 23Y 346/50 242 330745766 330745816 330746053 29U 380/60 290 330745766 330745816 330746053 23H 440/50 242 330745767 330745817 330746053 29N 200/60 290 330745768 330745818 330746053 29B 208/60 290 330745768 330745818 330746053 29P 220/60 290 330745769 330745819 330746053 29V 230/60 290 330745769 330745819 330746053 29W 240/60 290 330745769 330745819 330746053 23F 380/50 242 330745770 330745820 330746053 23G 400/50 242 330745770 330745820 330746053 23K 415/50 242 330745770 330745820 330746053 29A 440/60 290 330745770 330745820 330746053 29R 460/60 290 330745770 330745820 330746053 29S 480/60 290 330745770 330745820 330746053 29D 575/60 290 330745771 330745821 330746053 29E 220/50 292 330745772 330745872 330746054 29Y 346/50 292 330745773 330745873 330746054 35U 380/60 350 330745773 330745873 330746054 29H 440/50 292 330745774 330745874 330746054 35N 200/60 350 330745775 330745875 330746054 35B 208/60 350 330745775 330745875 330746054 35P 220/60 350 330745776 330745876 330746054 35V 230/60 350 330745776 330745876 330746054 35W 240/60 350 330745776 330745876 330746054 29F 380/50 292 330745777 330745877 330746054 29G 400/50 292 330745777 330745877 330746054 29K 415/50 292 330745777 330745877 330746054 35A 440/60 350 330745777 330745877 330746054 35R 460/60 350 330745777 330745877 330746054 35S 480/60 350 330745777 330745877 330746054 35D 575/60 350 330745778 330745878 330746054 35E 220/50 333 330745779 330745879 330746055 35Y 346/50 333 330745780 330745880 330746055 40U 380/60 400 330745780 330745880 330746055 35H 440/50 333 330745781 330745881 330746055 40N 200/60 400 330745782 330745882 330746055 40B 208/60 400 330745782 330745882 330746055 1 Digits 9, 10, 11 in compressor model number. 2 Rotor and Low Speed Shaft shrunk fit together. RPL 7000053 / Page 48