IMPORTANT SAFETY INSTRUCTIONS Informer Compact Series LINE-INTERACTIVE SINEWAVE UPS Uninterruptible Power System WARNING : (SAVE THESE INSTRUCTIONS) This manual contains important safety instructions. Please follow up all instructions carefully during installation. Read this manual thoroughly before attempting to unpack, install or operate. CAUTION : To prevent the risk of fire or electric shock, please install the unit in a temperature and humidity controlled indoor area, which is free of conductive contaminants. CAUTION : risk of electric shock, do not remove the cover. No user serviceable parts. Refer servicing to qualified service personnel. CAUTION : Risk of electric shock. Hazardous live parts inside this UPS can be energized from the battery supply even when the input AC power is disconnected. CAUTION : Risk of electric shock. Battery Circuit is not isolated from AC input, hazardous voltage may exist between battery terminals and ground. Please test it before touching. kva / 2kVA / 3kVA USER MANUAL WARNING - This is a Class A-UPS Product. In a domestic environment, this product may cause radio interference, in which case, the user may be required to take additional measures. NOTICE- The UPS is designed to be for use with computer loads only.
) INSPECTION Inspect the UPS upon receipt. Notify the carrier and dealer if there is damage. The package is recyclable; save it for reuse or dispose of it properly. 2) PLACEMENT 4) CONNECTION OF TELEPHONE/NETWORK SURGE PROTECTION Connect a 0 base-t / 00 base-t network cable into the RJ-45 network surge protection IN jack on the rear panel of the UPS. Connect from the OUT jack with network cabling to network equipment. 3) LOAD CONNECTION First, connect the UPS with Utility, then plug the loads into the outlets on the rear of the UPS. To use the UPS as a master On/Off switch, make sure that all of the loads are switch On. These UPS outlets provide battery power and surge protection to the equipment when utility voltage is outside acceptable limits. 5) CONNECTION OF COMPUTER INTERFACE PORT Connect the supplied interface cable (RS-232 ) to the interface port on the rear of the UPS through the computer interface port. See software installation guide in the CD-ROM (Optional) for installation purpose. Caution: Do not connect a laser printer to the outlets. 2 3
) START UP. Connect the UPS to the wall receptacle. 2. Push the On Switch on the front panel of the UPS until 4 LEDs (LCD) are lit then extinguished and release the On Switch. If you release your finger before the LED lights are off then the ups shall not start up. Therefore please keep your finger on the ON button until the LEDs are off. After then the ups starts to operate. 3. The Backup mode LED (Amber) lights up and the UPS is under self-test mode now. If Utility is normal, the UPS will run under Utility mode (Green LED) after its self-test is completed. On the contrary, the UPS will run under Backup mode and the buzzer alarms every 2 seconds in case of blackout or over/under voltage. Caution:. The UPS On will not be executed if the above procedure is not done completely, which means the button is released before all 4 LEDs (LCD) are extinguished. 2. The UPS will remain at NO output, if the start-up operation is not proceeded properly even though the Input Power Cord is connected to the wall receptacle. IMPORTANT NOTICE: Plug the UPS into the wall receptacle to charge the UPS for over 8 hours after initial installation STORAGE: Store at -5 to +30 C (+5 to +8 F), charge the UPS battery every six months. Store at +30 to +45 C (+8 to +3 F), charge the UPS battery every three months. 4 ) OPERATION TEST Turn Off the UPS Push the Off Switch for at least 3 seconds to turn off the UPS. If you press the Off Switch less than 3 seconds, the UPS will not execute shutdown command due to insufficient pressing time. In some occasions, the UPS will shut itself down in case of overload, output short-circuited or battery cutoff point reached in the Backup mode. The UPS will automatically shut off the output and beep for 5 seconds then completely shut itself down. Plug-in Charge If the Input Power Cord is connected to the wall receptacle properly and the utility is normal, the UPS will start to charge automatically without processing Turn On procedure. You have to charge for at least 8 hours every 3 months to avoid from battery self over-discharge naturally, if the UPS is in an idle condition. Auto-Restart The UPS will automatically restart to provide energy to the output if the utility recovers in 24 hours after battery cut. The Backup LED will flash every 5 seconds under the waiting situation. On the contrary, the UPS will not auto-restart if the Utility doesn t recover within 24 hours. You are required to start up the UPS manually. If you don t need UPS auto-restart, you can turn off the UPS by proceeding the Turn Off procedure. Alarm Silence The Alarm might be turned off by pushing the On Switch for approximately second in the Backup mode. Unless any other warning or fault condition occurs, the alarm remains at Silence condition once the Alarm Silence is turned off. Test Under Utility Normal condition, push the On Switch for 3 seconds to execute the Battery Self-test function. In case the battery is normal, it will enter into Battery Backup Mode for 0 seconds then return back to Utility Mode. If the battery voltage is detected lower than set limit, the Battery Replacement LED will blink for 5 seconds then extinguish to stop self-test procedure. And if battery is detected weak or dead, the Battery Replacement LED will steadily illuminate. 5
8) FRONT PANEL EXPLANATIONS 9) REAR PANEL EXPLANATIONS 2 3 8 9 0 2 5 3 2 4.Utility LED 2. Fault LED 3.On Switch 4.Off Switch 5.Battery Replacement LED.Battery Backup LED 5. RJ45 Port 2. DIP Switch 3. RS232 Communication Port 4. Outlet 5. Rating Label. Input Fuse. Input Power Cord(Inlet)).Battery Low 8.Bypass 4 3 4 5 2 9.Utility Low, UPS Boost 0.Utility High, UPS Buck.UPS Output Indicator 2.Polarity Error/Ground Fault 3.Over load 4.Load/Battery Level (%) 5.Load/Battery Level Indication Control Button 0) DIP SWITCH SETTING The voltage & frequency of the UPS might be re-set by the DIP Switch on the rear panel of the UPS. The following charts may bring you clear pictures about how the settings are done by the DIP Switch
) INDICATORS AND ALARMS Indicator Color Description Alarm Utility Mode Green Steady: Output Load is supplied by Utility. None Blinking: Polarity error or Ground Fault Backup Mode Amber Steady (with alarm): Output Load is supplied by Battery Blinking every 5 seconds(no alarm):stand by for Utility recovery to re-start up Every 2 seconds before battery Low and every second before battery Cutoff. Fault Red When Overload, short circuit, or Output Voltage Abnormal occurs Buzzer beeps continuously. Battery Replacement Red Blinking: Battery is weak and needs to be recharged. None Steady: Battery is dead. 8