OWNER'S MANUAL FOR 135LB STAINLESS STEEL SPREADER SNOWRATOR

2017 OWNER'S MANUAL FOR 135LB STAINLESS STEEL SPREADER SNOWRATOR AES L. T. RICH PRODUCTS 11/16/2017

TABLE OF CONTENTS 1.0 SHIPPING CONTENTS... 2 2.0 IMPORTANT INFORMATION... 3 2.1 ABOUT THIS MANUAL... 3 2.2 OVERVIEW... 3 2.3 SAFETY... 3 2.4 MAINTENANCE... 4 2.5 RELATED DOCUMENTS... 4 3.0 INSTALLATION... 5 3.1 TOOLS & EQUIPMENT... 6 4.0 INSTALLATION... 7 4.1 FERTILIZER BOXES... 7 4.2 SPREADER... 11 4.3 SPEED CONTROL UNIT... 14 4.4 AUX CONTROL PANEL... 17 4.5 TEST... 20 5.0 OPERATION... 21 5.1 OPERATIONAL CONTROLS... 21 5.2 SPREAD PATTERN ADJUSTMENT CONTROLS... 23 5.3 SPREAD PATTERN SET-UP... 28 6.0 PARTS LIST... 30 For any questions please contact us at toll free (877) 482-2040 Mon-Fri 8 a.m. to 4:30 p.m. 1

1.0 SHIPPING CONTENTS SR-HOPPER KIT (135) ITEM QTY P/N DESCRIPTION PICTURE ITEM QTY P/N DESCRIPTION PICTURE 1 1 N/A SPREADER, STAINLESS STEEL, 135LB 14 1 SM10403 RIGHT FERTILIZER BOX PLATFORM 2 1 70038 SPEED CONTROL UNIT 15 1 SM10402-R RIGHT FERTILIZER BOX UPRIGHT 3 1 N/A CONTROL PANEL, AUX 16 2 CB-51634SS CARRIAGE BOLT, 5/16 x 3/4 4 1 80238 ELECTRICAL HARNESS 17 4 CB-5161SS CARRIAGE BOLT, 5/16 x 1 5 1 N/A SWITCH, ROCKER, RED 18 4 CB-381SS CARRIAGE BOLT, 3/8 x 1 6 2 SM10193 HOPPER MOUNTING LATCH 19 1 HCSSC-1012 HEX CAP SCREW, 10-24 x 1/2 7 2 SC1-0500-SS SPLIT SHAFT COLLAR, 1/2" 20 4 TRCP-1012S TRUSS SCREW, 10-32 x 1/2 8 2 80748 QUICK RELEASE PIN, 3/8" x 1-1/2" 21 4 FWSS-516 WASHER, 5/16 9 2 30679 KNOB 22 1 SSNNC-1024 NYLOCK NUT, 10-24 10 1 ZB200305-L LEFT FERTILIZER BOX 23 4 HFNCS-10S SERRATED FLANGE LOCK NUT, 10-32 11 1 SM10401 LEFT FERTILIZER BOX PLATFORM 24 4 HFNCS-38S HEX FLANGE NUT, 3/8 12 1 SM10402 LEFT FERTILIZER BOX UPRIGHT 25 5 CTB-1550 15" CABLE TIE 13 1 ZB200305-RW RIGHT FERTILIZER BOX For any questions please contact us at toll free (877) 482-2040 Mon-Fri 8 a.m. to 4:30 p.m. 2

2.0 IMPORTANT INFORMATION 2.1 ABOUT THIS MANUAL The purpose of this manual is to assist you in properly and safely operating and maintaining the 135lb Stainless Steel Spreader. Read and understand this entire manual before attempting to setup, operate, adjust, perform maintenance on, or store this attachment. This manual provides essential information and instructions, which will help you enjoy years of dependable performance. The designed and tested safety of the 135lb Stainless Steel Spreader is dependent upon its operations within the parameters and limitations explained in this manual. Be familiar with and follow all safety rules in this manual as well all safety rules for any related equipment, including the Snowrator. Although these instructions have been complied through extensive field experience and engineering data, some information presented herein may be generated in the nature due to unknown and/or varying operating conditions. However, these instructions, combined with your increased experience with the Snowrator, will enable you to develop procedures suitable to your particular application. The illustrations and data used in the manual were current at the time of printing, but the Snowrator and 135lb Stainless Steel Spreader may vary slightly due to ongoing engineering changes. L. T. Rich Products, Inc reserves the right to implement engineering and design changes to the Snowrator as may be necessary without prior notification. 2.2 OVERVIEW The 135lb Stainless Steel Spreader is an optional attachment that can be mounted to the Snowrator and used to spread salt/granular product. It has an electric hopper motor with a spreader control rate knob which allows variable spread distances from 3 to 25 feet. This depends on volume/density, particle size and rate of travel, and weather conditions. The pattern can be increased or decreased while spreading depending on needs. Travel at a constant speed for consistent results. Remember-Published dial settings are approximate only. The 135lb Stainless Steel Spreader Attachment features stainless steel construction, electronic speed control, agitator, rate control and directional control. 2.3 SAFETY Safety is a primary concern in the design and manufacturing of all L. T. Rich Products. Unfortunately, our extensive efforts to provide safe equipment can be negated by a single careless act of an operator. In addition to the design and configuration of the 135lb Stainless Steel Spreader, hazard control and accident prevention are also dependent upon the awareness, condition, maintenance, and storage of the Snowrator and all optional attachments. This section is only for the 135lb. Stainless Steel Spreader. Please refer to the Owner's Manual for applicable safety information for the Snowrator. Additional safety tips are provided throughout this document. For any questions please contact us at toll free (877) 482-2040 Mon-Fri 8 a.m. to 4:30 p.m. 3

Safety Cont 2.3.1 Safety Equipment When using or performing maintenance on the 135lb Stainless Steel Spreader, it is recommended that the operator wear gloves and safety glasses. 2.3.2 Mounting and Dismounting Two people using proper lifting techniques are required to mount and dismount the 135lb. Stainless Steel Spreader. The risk of injury and/or damage to the unit is significantly increased if only one person is performing this activity. 2.3.3 Impeller Turn off the Impeller via the toggle switch on the Speed Control Unit before adjusting spread pattern settings. ALWAYS keep fingers, hands, loose clothing, etc. clear of this area when it is in use. 2.3.4 Operation Always scan the environment to ensure the product being spread does not come into contact with other people and animals. Follow all guidelines provided in the Snowrator Owner's Manual. 2.4 MAINTENANCE Follow all safety guidelines when performing maintenance on the 135lb Stainless Steel Spreader. In order to ensure the 135lb. Stainless Steel Spreader is kept in optimum condition, perform the following maintenance activities on a regular basis. DO NOT USE WATER WHEN CLEANING HOPPER Daily Clean debris and product from Hopper daily USING COMPRESSED AIR ONLY, to eliminate build up. Check daily to make sure guides (4) are not damaged to allow the hopper door to slide freely. Weekly Lubricate Hopper cables with Silicone Spray weekly. 2.5 RELATED DOCUMENTS Snowrator Owner s Manual Installation Guide for 135lb Stainless Steel Spreader Conversion Kit (SRA-10020) For any questions please contact us at toll free (877) 482-2040 Mon-Fri 8 a.m. to 4:30 p.m. 4

3.0 INSTALLATION WARNING Before Working on This Machine Switch Engine to OFF Please note that this installation guide is for a standard machine only. The hose and electrical harness routing may be different depending on the attachments that may already be installed on your machine. A SNOWRATOR machine is shown for all assembly photos. For any questions please contact us at toll free (877) 482-204 Mon-Fri 8 a.m. to 4:30 p.m. For any questions please contact us at toll free (877) 482-2040 Mon-Fri 8 a.m. to 4:30 p.m. 5

3.1 TOOLS & EQUIPMENT ITEM QTY DESCRIPTION PHOTO 1 1 DRILL 2 1 DRILL BIT, 3/8" 3 1 RATCHET 4 1 SOCKET, 13/16" 5 1 EXTENSION, SOCKET, 1-1/2" 6 6 WRENCH: 3/8", 1/2", 5/16", 7/16", 9/16", 13/16" 7 1 ALLEN WRENCH, 1/8" 8 1 SCREWDRIVER, PHILLIPS, NO. 2 9 1 UTILITY KNIFE 10 1 JACK, 1 TON ITEM QTY DESCRIPTION PHOTO 1 1 GLOVES 2 1 SAFETY GOGGLES For any questions please contact us at toll free (877) 482-2040 Mon-Fri 8 a.m. to 4:30 p.m. 6

4.0 INSTALLATION 4.1 FERTILIZER BOXES 4.1.1 Remove Rear Tires. Ratchet with 13/16 Socket Raise the machine using a Jack and Jack Stands (not shown). Remove both Rear Tires. B B 4.1.2 Remove Rear Light Bracket. Ratchet with 1/2 Socket Remove the two Bolts connecting the Rear Light Bracket to the Frame. Lay Rear Light Bracket gently on the Frame (not shown). A The bolts from step 4.1.2 may be discarded, but the flange nuts will be reused when the Rear Light Bracket is reattached. For any questions please contact us at toll free (877) 482-2040 Mon-Fri 8 a.m. to 4:30 p.m. 7

Fertilizer Boxes Cont 4.1.3 Remove Battery Box. Ratchet with 1/2 Socket Remove battery cover by unhooking strap. Detach the Negative (black) and Positive (red) Wires from battery. Remove bolts that attach the Battery Box Bracket to the Frame. Remove Battery Box Bracket from Frame. A B C 3c D The bolts from step 4.1.3 may be discarded, but the flange nuts will be reused when the battery box is re-attached. For any questions please contact us at toll free (877) 482-2040 Mon-Fri 8 a.m. to 4:30 p.m. 8

Fertilizer Boxes Cont 4.1.4 Attach the Right Fert Box Platform Ratchet with 9/16 Socket Insert (2) 3/8 x 1 Bolt into Footplate Bracket Line up Slot in Fert Box Platform with Bolts Fasten with (2) 3/8 Flange Nuts. A B C Hand Tighten Wrench, 1/2 Wrench, 9/16 4.1.5 Attach the Battery Box Bracket Replace 5/16 x ¾ Bolts in Battery Box Bracket with 5/16 x 1 Bolts Align Fert Box Platform to Fender and Battery Box Bracket Tighten all (4) Bolts to Foot Plate Bracket and Fender Re-Connect the Red Battery Cable (not shown) *** DO NOT CONNECT NEGATIVE (BLACK) BATTERY CABLE UNTIL READY TO TEST! *** A B C Use the existing 5/16 Flange Nuts removed during Setup, step 4.1.3 For any questions please contact us at toll free (877) 482-2040 Mon-Fri 8 a.m. to 4:30 p.m. 9

Fertilizer Boxes Cont 4.1.6 Attach the Left Fert Box Platform Ratchet with 9/16 Socket Insert (2) 3/8 x 1 Bolt into Footplate Bracket Line up Slot in Fert Box Platform with Bolts Fasten with (2) 3/8 Flange Nuts A B C Hand Tighten Wrench, 1/2 Wrench, 9/16 4.1.7 Attach Rear Light Bracket Insert (2) 5/16 x 1 Bolt into Rear Light Bracket Align Fert Box Platform to Fender and Rear Light Bracket Tighten all (4) Bolts to Foot Plate Bracket and Fender A B C Use the existing 5/16 Flange Nuts removed during step 4.1.2 For any questions please contact us at toll free (877) 482-2040 Mon-Fri 8 a.m. to 4:30 p.m. 10

Fertilizer Boxes Cont 4.1.8 Attach Rear Tires Ratchet with 13/16 Socket Attach Rear Tires. Lower Machine and remove Jack. Fertilizer Boxes Cont Drill, 3/8 bit 4.2 SPREADER This section requires TWO people in order to install it safely. Always use safe lifting techniques. Take care not to pinch fingers or drop the spreader during installation. 4.2.1 Mount 135lb Stainless Steel Spreader Drill out the quick-release pin hole on the Mounting Plate of Snowrator With one person on each side, lift the 135lb Stainless Steel Spreader by the Back Shield and the rear of the Hopper. A B B Back Front For any questions please contact us at toll free (877) 482-2040 Mon-Fri 8 a.m. to 4:30 p.m. 11

Mount Spreader Cont... Rest the rear of base on the Mounting plate with the front at a slightly elevated angle. Slide the Hopper Hinge Rods down into the rear Mounting Plate hooks. C D D Set the front of base down so the Hopper Latch Rods are in the front Mounting Plate Hook. E E E Attach Latches to the Hopper Latch Mounting Rods. F F F For any questions please contact us at toll free (877) 482-2040 Mon-Fri 8 a.m. to 4:30 p.m. 12

Mount Spreader Cont... Allen Wrench, 1/8 Secure both Latches with a 1/2 Split Shaft Collar. Align 1/2 Split Shaft Collar so it is flush with the outer edge of the Hopper Latch Rod and tighten. G G H Insert Quick Release Pin through Hopper Latch, Base and Mounting Plate on both sides of the Hopper Base. Set the Hopper Cable, Agitator Connector and Impeller Motor Connector off to the side (Not shown). These will be connected in the next section. I I I For any questions please contact us at toll free (877) 482-2040 Mon-Fri 8 a.m. to 4:30 p.m. 13

Utility Knife 4.3 SPEED CONTROL UNIT 4.3.1 Speed Control Unit, Mechanical Rub Slot Edges to reveal Cut location Cut into Main Control Panel using utility knife A B Ratchet with 11/32 Socket Phillips Screwdriver Insert Speed Control Unit in the Main Control Panel Cutout. Insert (4) 10-32 x 1/2 Phillips Screws in Mounting Holes on Speed Control Unit Fasten to Main Control Panel with (4) 10-32 Flange Nuts C D E Under Control Panel For any questions please contact us at toll free (877) 482-2040 Mon-Fri 8 a.m. to 4:30 p.m. 14

4.3.2 Speed Control Unit, Electrical Ratchet with 3/8 Socket Wrench, 5/16 Phillips Screwdriver Fuse Holder 1. Locate Fuse Mounting Hole in the inside rear of Upright. 2. Mount Fuse to the rear upright panel with (1) 10-24 x 1/2 Cap Screw and (1) 10-24 Nylock Nut A1 A2 Ratchet with 3/8 Socket B1 Power and Ground Wires 1. Route Power and Ground Wires to lower section of left upright. 2. Remove Nut from Terminal Block 3. Connect Power Wire to Terminal Block and fasten nut. B2, 3 Some parts not shown for clarity For any questions please contact us at toll free (877) 482-2040 Mon-Fri 8 a.m. to 4:30 p.m. 15

Speed Unit,Elect. Cont. Ratchet with 1/2 Socket C1 Ground Wire 1. Remove Bolt on Center Ground Post. 2. Connect Ground Wire to Center Ground Post and fasten nut. C2 Impeller Motor Connector 1. Connect the Impeller Motor Connector from the Speed Control Unit to the Impeller Motor. D1 Green and Blue Trim For any questions please contact us at toll free (877) 482-2040 Mon-Fri 8 a.m. to 4:30 p.m. 16

4.4 AUX CONTROL PANEL 4.4.1 Aux Control Panel, Mechanical Insert (1) 5/16 x 3/4 Carriage Bolt in the top Aux Control Panel mounting location. Position the Aux Control Panel on the bolt. Fasten with (2) 5/16 Washers and (1) Hand Knob. Insert (1) 5/16 x 3/4 Carriage Bolt in the bottom Aux Control Panel mounting location. Fasten with (2) 5/16 Washers and (1) Hand Knob. A B C D E Completed Installation For any questions please contact us at toll free (877) 482-2040 Mon-Fri 8 a.m. to 4:30 p.m. 17

4.4.2 Aux Control Panel, Electrical Switch Connector 1. Connect the Switch Connector on the Electrical Harness to the connector on the back of the Agitator Switch. A All Black Ratchet with 1/2 Socket Power Wire 1. Remove Nut on Solenoid. 2. Connect Power Wire to Solenoid Post and fasten nut. B1 B2 Power Wire For any questions please contact us at toll free (877) 482-2040 Mon-Fri 8 a.m. to 4:30 p.m. 18

Aux Panel, Elect. Cont. Ratchet with 7/16 Socket 3. Remove Nut from right side of Rectifier. 4. Connect Ground Wire to Rectifier Bolt and fasten nut B4 B5 B5 Agitator Switch Connector 1. Connect the Agitator Switch Connector from the Aux Electrical Harness to the Agitator motor. D Green Trim For any questions please contact us at toll free (877) 482-2040 Mon-Fri 8 a.m. to 4:30 p.m. 19

4.5 TEST Connect the Negative (black) Battery Cable before testing. Refer to section 5 for Operating Instructions. 4.5.1 Agitator Verify the electrical connections have been made properly. Turn on the Agitator. Listen for vibration. Turn off the Agitator. 4.5.2 Speed Control Unit Verify the electrical connections have been made properly. Put the toggle switch in the downward position to start the impeller. Put the toggle switch in the middle position to turn off the impeller. 4.5.3 Plow Clearance Check for clearance between the plow and the Directional Control after each step. The plow should have clearance when the Directional Control is open at its minimum and maximum positions (See Section 5.2.2). Refer to the Snowrator Owner s Manual for more information. Adjust the plow to its maximum upward position. Adjust the plow all the way to the left. Adjust the plow all the way to the right. Return the plow to the center position. For any questions please contact us at toll free (877) 482-2040 Mon-Fri 8 a.m. to 4:30 p.m. 20

5.0 OPERATION 5.1 OPERATIONAL CONTROLS The 135lb Stainless Steel Spreader has four controls. These are the Agitator Switch, Impeller Switch, Impeller Speed Control, and Hopper Cable. These controls can be operated while the spreader is in use. 5.1.1 AUX Control Panel The Hopper Cable is located to the left of the Agitator Switch. This Cable opens the Hopper Door when pulled upward and closes the Hopper Door when pushed downward. The Hopper Cable will only open as far as the Rate Control setting will allow. The Agitator Switch is located to the right of the Hopper Cable. It has a built-in light that indicates when it is on. Pressing the switch once will turn on the Agitator Motor mounted behind the Hopper Pressing it again will turn it off. Figure 1. Hopper Door Cable and Agitator Switch location Hopper Door Cable Agitator Switch For any questions please contact us at toll free (877) 482-2040 Mon-Fri 8 a.m. to 4:30 p.m. 21

5.1.2 Main Control Panel The Impeller Switch is a toggle switch located on the Speed Control Unit installed in the Main Control Panel. It has three modes, ON, OFF, and PULSE. Putting the switch in its down position (towards the operator) will turn the Impeller ON. The middle position turns the Impeller OFF. The up position (away from the operator) is used for PULSE mode. When it is in PULSE mode, the impeller will spin as long as the toggle switch is held in the up position. Letting it go, will return the Impeller to its OFF status. When the Impeller is on, it will rotate in whatever speed the Speed Control Unit is set to. Speed Control is adjusted via a rotary knob on the Speed Control Unit installed in the Main Control Panel. The rotary knob can be adjusted from settings one to ten, with ten being the fastest. This control should be dialed to the lowest setting before turning on the Impeller to reduce wear and tear on the motor. See section 5.2.2. Figure 2. Impeller Switch and Speed Control location Impeller Speed Control Impeller Switch For any questions please contact us at toll free (877) 482-2040 Mon-Fri 8 a.m. to 4:30 p.m. 22

5.2 SPREAD PATTERN ADJUSTMENT CONTROLS The 135lb Stainless Steel Spreader has four settings that can be adjusted to obtain the desired spread pattern, rate control, directional control, speed control and throw angle. These settings adjust for distance, density, direction and area. Since it is electrically driven, the spread pattern is independent of ground speed. It should be noted that these settings work together and the desired spread pattern should be observed while the machine is still. DO NOT attempt to adjust any of these settings, other than Speed Control, while the Impeller is spinning. 5.2.1 Rate Control Dial The Rate Control Dial is located on the front of the 135lb. Stainless Steel Spreader near the impeller. The Rate Control Dial setting controls the amount of product that is dispersed from the Hopper by adjusting how far the Hopper Cable can open the Hopper Door. The dial can be adjusted from settings zero through nine. The Rate Control setting primarily affects the density of the product spread in the coverage area. To adjust the Rate Control, pull the Dial Follower out as far as it will go and then rotate the dial to the desired setting. Push the Dial Follower in as far as it will go. Open the Hopper Door and visually inspect the Hopper Door opening. 2 1 3 4 5 For any questions please contact us at toll free (877) 482-2040 Mon-Fri 8 a.m. to 4:30 p.m. 23

5.2.2 Speed Control The Speed Control setting is a rotary knob located on the Speed Control Unit installed in the Main Control Panel. The speed control setting controls the length (distance) of the spread pattern by controlling how fast the Impeller rotates. This control also affects the density of the spread pattern. At the lowest speed, the product will be spread closer to the front of the machine with thicker coverage. As the impeller speed increases, the product will be spread farther from the front of the machine with thinner coverage. The spreader is capable of distances of 3-25 feet. Figure 3. Speed Control Unit Slow Fast Not to scale For any questions please contact us at toll free (877) 482-2040 Mon-Fri 8 a.m. to 4:30 p.m. 24

5.2.3 Directional Control The Directional Control setting is located on the front of the 135lb. Stainless Steel Spreader below the Rate Control Dial. The Directional Control setting controls the direction and width of the spray pattern by the orientation and width of the opening. The width of the opening also affects the density of the spread pattern as it will disperse the product over a wider area. Adjusting the angled handles with the index finger puts the thumb directly in the path of the impeller. To adjust the Directional Control safely, loosen the Hand Knob and grab the angled handles with your thumb (NOT the index finger) to slide both sides into the desired position before tightening. The leading edge of the spray pattern is controlled by the adjustment on the operator left. ***DO NOT attempt to adjust the Directional Control while the Impeller is spinning!*** 1 2 Minimum Opening Width Maximum Opening Width Figure 4. Spread Pattern Example Leading Edge Narrow Spread Pattern Wide Spread Pattern For any questions please contact us at toll free (877) 482-2040 Mon-Fri 8 a.m. to 4:30 p.m. 25

5.2.4 Throw Angle The Throw Angle is the angle at which the product leaves the Impeller. This feature controls the distribution of the product within the spread pattern by adjusting the angle of the impeller blades. Adjusting the throw angle enables greater control of when product exits the spreader allowing for heavier coverage on the right, even distribution, or heavier coverage on the left side of the spread pattern. When the blades are positioned to the left, the throw angle is increased, positioning them to the right decreases the throw angle. Increasing the throw angle will enable more product to be released on the left side of the spread area as well as increase the spread width. Decreasing the throw angle will increase the amount of product on the left side of the spray area. The orientation of the Impeller Blades (right or left) is from the perspective of the operator. **Before attempting to change the throw angle, disconnect the negative battery cable** To adjust the throw angle, use a 1/2 wrench or socket to loosen the nut closest to the edge of the impeller and then remove the bolt. Slide the impeller blade to the desire slot and fasten. Manually rotate the Impeller to repeat for all impeller blades. Make sure ALL bolts are tightened. Figure 5. Throw Angle Adjustment Assembly Standard Throw Angle Increase Throw Angle Decrease Throw Angle For any questions please contact us at toll free (877) 482-2040 Mon-Fri 8 a.m. to 4:30 p.m. 26

Figure 6. Throw Angle Chart Lighter Coverage Not to scale Even Coverage Heavier Coverage Increased Throw Angle Standard Throw Angle Decreased Throw Angle For any questions please contact us at toll free (877) 482-2040 Mon-Fri 8 a.m. to 4:30 p.m. 27

5.3 SPREAD PATTERN SET-UP This section contains instructions on how to set up a spread pattern with the 135lb. Stainless Steel Spreader. Note that other conditions such as weather, operator driving speed, etc. can affect the spread pattern. Adjust accordingly. 1. Make sure Impeller Switch is in the OFF position and the Snowrator is OFF. 2. Check the Hopper to verify it is clean and free of product. If not, clean it with compressed air. 3. Check Hopper sliding door guides for damage. 4. Set Rate Control using the Rate Control Dial on the front of the machine and verify Hopper Door opening width. 5. Adjust the Directional Control to the desired direction and opening width. 6. Adjust Throw angle. 7. Fill the Hopper with the desired product. 8. Set the Impeller speed to the lowest setting. 9. Turn on Agitator and Impeller. 10. Open Hopper Door and observe spread pattern. 11. Turn off Agitator and Impeller and adjust settings if necessary. Aux Control Panel Rate Control Speed Control (See Figure 3) Directional Control Throw Angle (See Figure 5) For any questions please contact us at toll free (877) 482-2040 Mon-Fri 8 a.m. to 4:30 p.m. 28

Figure 7. Spread Pattern Diagram Width 1. Directional Control 2. Throw Angle 3. Impeller Speed Not to scale Distance 1. Impeller Speed Direction 1. Directional Control Density 1. Rate Control 2. Impeller Speed 3. Throw Angle OPERATOR LEFT OPERATOR RIGHT For any questions please contact us at toll free (877) 482-2040 Mon-Fri 8 a.m. to 4:30 p.m. 29

6.0 PARTS LIST SR-HOPPER KIT (135) ITEM P/N DESCRIPTION PHOTO ITEM P/N DESCRIPTION PHOTO 1 SM10326-W FRAME UPRIGHT, RIGHT 16 90214 HOPPER LID HINGE 2 SM10326-WL FRAME UPRIGHT, LEFT 17 90136 SNOWRATOR LOGO DECAL 3 SM10202 BUMPER BACKPLATE 18 90135 MOTOR, AGITATOR, 12V 10A 4 SM10323 BUMPER 19 ZB200305-L FERT BOX, LEFT 5 SM10327 UPRIGHT SUPPORT BRACKET 20 ZB200305-RW FERT BOX, RIGHT 6 SM10328 BACKSHIELD 21 SM10401 FERT BOX PLATFORM, LEFT 7 SM10329 HOPPER CABLE BRACKET 22 SM10402 FERT BOX UPRIGHT, LEFT 8 SM10319-W SHELL, RIGHT 23 SM10402-R FERT BOX UPRIGHT, RIGHT 9 SM10319-WL SHELL, LEFT 24 SM10403 FERT BOX PLATFORM, RIGHT 10 SM10317 SHELL, REAR 25 90001 EDGING, TRIM-LOCK, 100B3X1/8 11 SM10318 SHELL, FRONT 26 SM10331-W DIRECTIONAL CONTROL MOUNTING PLATE 12 SM10320 SHELL, LID 27 SM10334-W DIRECTIONAL CONTROL, BOTTOM 13 SM10321 AGITATOR MOUNTING BRACKET 28 SM10336-W DIRECTIONAL CONTROL, MIDDLE 14 SM10322 AGITATOR, HEAT SHIELD 29 30679 KNOB 15 90121 HOPPER LID LATCH 30 SM10324 BOTTOM For any questions please contact us at toll free (877) 482-2040 Mon-Fri 8 a.m. to 4:30 p.m. 30

SR-HOPPER KIT (135) ITEM P/N DESCRIPTION PHOTO ITEM P/N DESCRIPTION PHOTO 31 SM10330 HOPPER DOOR 45 70028 IMPELLER MOTOR 32 70019 DIAL, SELECTOR 46 30732 IMPELLER SAFETY DECAL 33 70022 DIAL, HOLDER 47 SM10344 AUX CONTROL PANEL 34 70040 GUIDE, SLIDE DOOR 48 70014 HOPPER CABLE N/A 35 70041 DIAL, FOLLOWER 49 80243 SWITCH, ROCKER, SR 36 80316 FLANGE BEARING, 3/8" 50 80245 LENS, RED, SR 37 70014-B BALL JOINT 51 80238 ELECTRICAL HARNESS 38 70019-A PINE TREE CLIP 52 90137 AUX CONTROL PANEL DECAL 39 SM10338 IMPELLER 53 30679 KNOB 40 SM10339 THROW ANGLE BRACKET 54 SM10193 HOPPER MOUNTING LATCH 41 SM10325 IMPELLER MOTOR MOUNTING BRACKET 55 SC1-0500-SS SPLIT SHAFT COLLAR, 1/2" 42 70023-S IMPELLER MOTOR SHAFT 56 80748 QUICK RELEASE PIN, 3/8" x 1-1/2" 43 70024-C SHAFT COUPLER, 1" 57 90148 BRONZE BUSHING, 3/8" ID 44 70038 SPEED CONTROL UNIT For any questions please contact us at toll free (877) 482-2040 Mon-Fri 8 a.m. to 4:30 p.m. 31

7.0 AUX ELECTRICAL WIRING HARNESS DIAGRAM For any questions please contact us at toll free (877) 482-2040 Mon-Fri 8 a.m. to 4:30 p.m. 32