Bf-110 Messerschmitt The Messerschmitt Bf-110 was designed as a heavy fighter intended to escort bombers on long range missions that were beyond reach of escorting fighters. The Bf-110 was however incapable of defending itself against most contemporary fighters in WWII so the aircraft was adapted for use in many roles including fighter bomber, reconnaissance, light transport and finally as a night fighter in defense of the Reich during the later stages of WWII. The Bf-110 was used throughout the war but served a unique role in one of the most unusual stories from WWII. On May 10, 191 Deputy Fuhrer of the German Reich, Rudolf Hess piloted a BF-110 for a clandestine flight to the England with the apparent intention of negotiating a separate peace treaty with England. Hess parachuted from his Messerschmitt Bf- 110 and landed in the English countryside while the airplane flew on to crash in Scotland. Fragments of the airplane were recovered, and markings were determined after a close inspection of photographs of the crash site. Rudolf Hess was never had a chance to begin negotiations since any knowledge of the flight was denied by Adolf Hitler and Deputy Fuhrher Hess was condemned by the German government as having gone mad. Hess served the duration of WWII in an English POW camp and after the war stood trial at the Nurnberg War Crimes trials. Having been convicted of war crimes, Hess spent the rest of his life in Spandau Prison. This Minicraft kit offers markings for the following aircraft: Me 110, German Luftwaffe, Rudolf Hess s aircraft, May 191 Me 110, German Luftwaffe, I/ZG 26, Battle of Britain, Summer-Fall 190 Minicraft Models, 101 Commerce Drive, Elgin IL 6012 USA www.minicraftmodels.com Printed in China
Your MINICRAFT Me-110 may be assembled with various options, such as 'In-flight' features as retracted landing gear and 'spinning' propellers. Parts are also provided for a 'stationary' or 'ground' version with extended landing gear. Please review the assembly steps to become familiar with the parts before beginning assembly. PARTS LAYOUT DIAGRAM Cement Do Not Cement Optional Symmetrical L/R 9 10 16 26 1 1 1 20 19 18 17 21 22 11 12 2 2 8 7 2 2 Display nameplate Canopy 6 1 1 STATIONARY VERSION 2 9 11 Propeller blades - RLM 70 BLACK-GREEN except as noted 21 11 IN-FLIGHT VERSION 12 22 12 10 7 26 Canopy 2 6 8 1 19 Exhausts - BURNT METAL Cockpit interior - RLM 66 BLACK-GREY 18 20 17 IN-FLIGHT VERSION 6 2 2 STATIONARY VERSION Cut parts 2/2 in two 16 1 2 (Cut) 2 (Cut) 2 (Cut) 1 1 2 (Cut) Wheel well / gear door interiors - RLM 02 GRAY-GREEN Struts - RLM 02 GRAY-GREEN Hubs - RLM 66 BLACK-GRAY Tires - FLAT BLACK-GRAY
ME 110, German Luftwaffe, Rudolf Hess's aircraft, May 191 PAINTS A RLM 02 Gray (ModelMaster 2071, Acryl 770) B RLM 71 Dark Green (ModelMaster 2081, Acryl 781) C RLM 21 White (ModelMaster 17, Acryl 696) D RLM 70 Black Green (ModelMaster 2080, Acryl 780) E RLM 6 Light Blue (ModelMaster 2078, Acryl 782) F RLM 0 Yellow (ModelMaster 2072, Acryl 771)
ME 110, German Luftwaffe, I/ZG 26, Battle of Britain, Summer-Fall 190
Your Minicraft model includes high-quality waterslide decals. These decals adhere best to a glossy surface; and it is recommended that you apply a clear gloss coat over your painted model. Use a sharp scissors or knife to cut individual decals from the carrier sheet. Do not cut into the clear film surrounding the individual decals. * It is recommended that you apply one decal at a time. * Place the decal section in warm water, when first inserted in the water your decal will curl, after approximately ten seconds the decal will uncurl. Remove from water and lay on a paper towel. After approximately 10-20 seconds the decal will slide freely from the backing paper. Use a small brush to help slide the decal from the backing paper and into position on the model. Carefully blot excess water from the decal, using care not to move the decal or tear it. * If you choose to use a setting solution, apply a thin coat over the decal following the manufacturer s instruction. * Allow the decal to dry overnight. Wash any adhesive residue off the model with a small amount of clean water and dry thoroughly. * Apply clear gloss, matte or flat coat to seal decals following the instructions from the manufacturer. Visit our Websitewww.minicraftmodels.com Minicraft Models 101 Commerce Drive Elgin, IL 6012 Phone: 87-29-9676