TENDER DOCUMENT. (TENDER No: NRO/CON/696/660) FOR

TENDER DOCUMENT (TENDER No: ) FOR BALANCE WORK OF SUPPLY, INSTALLATION, TESTING & COMMISSIONING OF TWO NO. 11/0.433KV INDOOR ELECTRIC SUBSTATION (ESS-1 & 2), THREE NO. OUTDOOR TYPE 11/0.433KV COMPACT SUB-STATION (CSS-1, 2 &3) AND OTHER ASSOCIATED EXTERNAL ELECTRICAL WORKS FOR THE PERMANENT CAMPUS OF THE CENTRAL UNIVERSITY OF JAMMU (CUJ) AT VILLAGE BAGLA, DISTT. SAMBA (J&K) VOLUME III BOQ / PRICE BID PROJECT MANAGEMENT CONSULTANT: ENGINEERING PROJECTS (INDIA) LIMITED (A GOVT. OF INDIA ENTERPRISE) Northern Regional office 2 ND Floor, CORE-3, SCOPE COMPLEX, 7 LODHI ROAD, NEW DELHI 110003. TEL. NO: 011-24361666 FAX NO: 011-24363426 E-Mail: nrommd@engineeringprojects.com

ENGINEERING PROJECTS (INDIA) LTD. TENDER FOR BALANCE WORK OF SUPPLY, INSTALLATION, TESTING & COMMISSIONING OF TWO NO. 11/0.433KV INDOOR ELECTRIC SUBSTATION (ESS-1&2), THREE NO. OUTDOOR TYPE 11/0.433KV COMPACT SUB-STATION (CSS-1,2&3) AND OTHER ASSOCIATED EXTERNAL ELECTRICAL WORKS FOR THE PERMANENT CAMPUS OF THE CENTRAL UNIVERSITY OF JAMMU (CUJ) AT VILLAGE BAGLA, DISTT. SAMBA (J&K). NIT No. PRICE BID FOR QUOTING SHEET S. No. Section Description Annexure-X 1.0 A POWER SUPPLY PACKAGE FOR SUBSTATION 1 Estimated Cost (Rs.) 1.1 POWER SUPPLY PACKAGE FOR SUBSTATION 1 (As per 2013) 1270208.00 1.2 POWER SUPPLY PACKAGE FOR SUBSTATION 1 (As per Non ) 12748660.00 Bidder's Price Amount in Rs. After adding Percentage at % Quote at Above/ PAR/ Below Above/ PAR/ Below In Figures In Words In Figures In Words 2.0 B POWER SUPPLY PACKAGE FOR SUBSTATION II & COMPACT TYPE SUBSTATION 2.1 POWER SUPPLY PACKAGE FOR SUBSTATION II & COMPACT TYPE SUBSTATION (As per 2013) 2.2 POWER SUPPLY PACKAGE FOR SUBSTATION II & COMPACT TYPE SUBSTATION (As per Non ) 3.0 C EXTERNAL LIGHTING 3.1 EXTERNAL LIGHTING WORK (As per 2013) 3.2 EXTERNAL LIGHTING WORK (As per Non ) 4.0 D CIVIL WORK 4.1 CIVIL WORK (As per 2013) 1714164.00 22329210.00 22452.00 99480.00 6552688.00 4.2 CIVIL WORK (As per Non ) 600.00 Annexure-Y 5.0 E MISC. CIVIL, ELECTRICAL & FIRE FIGHTING WORK 5.1 MISC. CIVIL, ELECTRICAL & FIRE FIGHTING WORK (As per 2013) 931243.00 5.2 MISC. CIVIL, ELECTRICAL & FIRE FIGHTING WORK (As per Non ) 375668.40 I Total amount for items 10490755.00 II Total amount for Non items 35553618.40 III Total (I+II) 46044373 Note:- BIDDER FINANICIAL OFFER Rs:-( IN FIGURES) Rs:-( IN WORDS) Quoted rates shall be inclusive of all taxes & duties including GST. SEAL AND SIGNATURE OF BIDDER 1 of 1

Annexure-X TENDER FOR BALANCE WORK OF SUPPLY, INSTALLATION, TESTING & COMMISSIONING OF TWO NO. 11/0.433KV INDOOR ELECTRIC SUBSTATION (ESS-1&2), THREE NO. OUTDOOR TYPE 11/0.433KV COMPACT SUB-STATION (CSS-1,2&3) AND OTHER ASSOCIATED EXTERNAL ELECTRICAL WORKS FOR THE PERMANENT CAMPUS OF THE CENTRAL UNIVERSITY OF JAMMU (CUJ) AT VILLAGE BAGLA, DISTT. SAMBA (J&K). SECTION - A: ABSTRACT COST FOR BALANCE WORK OF POWER SUPPLY PACKAGE FOR SUBSTATION - I (POWER SUPPLY PACKAGE & EXTERNAL ELECTRICAL WORKS) SUMMARY SHEET SUB-HEAD SH. DESCRIPTION ESTIMATED COST IN RUPEES -2013 TOTAL I. H.T. CABLE & VACUUM CIRCUIT BREAKERS 104,054.00 2,037,000.00 2,141,054.00 II. DISTRIBUTION TRANSFORMER & BUS TRUNKING 611,750.00 3,254,000.00 3,865,750.00 III. DG SETS & ACCESSORIES 0.00 4,078,000.00 4,078,000.00 IV. MAIN L.T. PANELS, CAPACITOR BANK PANELS & SUB-DISTRIBUTION BOARDS 0.00 3,313,000.00 3,313,000.00 V. LT CABLES 386,154.00 66,660.00 452,814.00 VI. EARTHING 168,250.00 0.00 168,250.00 TOTAL AMOUNT 1,270,208.00 12,748,660.00 14,018,868.00 SAY Rs. 14,018,868.00

TENDER FOR BALANCE WORK OF SUPPLY, INSTALLATION, TESTING & COMMISSIONING OF TWO NO. 11/0.433KV INDOOR ELECTRIC SUBSTATION (ESS-1&2), THREE NO. OUTDOOR TYPE 11/0.433KV COMPACT SUB-STATION (CSS-1,2&3) AND OTHER ASSOCIATED EXTERNAL ELECTRICAL WORKS FOR THE PERMANENT CAMPUS OF THE CENTRAL UNIVERSITY OF JAMMU (CUJ) AT VILLAGE BAGLA, DISTT. SAMBA (J&K). SECTION - A: ABSTRACT COST FOR BALANCE WORK OF POWER SUPPLY PACKAGE FOR SUBSTATION - I (POWER SUPPLY PACKAGE & EXTERNAL ELECTRICAL WORKS) Description Qty. Unit NON- Amount as per Amount as per NON -2013 / I. H.T. CABLE & VACUUM CIRCUIT BREAKERS H.T. CABLE 1.0 Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 11KV grade of following sizes direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc. as required. 8.1 (-2013) i) Above 120sqmm and upto 400 sqmm. 100 M 256.00 25,600.00 8.1.2 1.0A (Part of sec.-b) Laying of one number additional PVC insulated and PVC sheathed / XLPE power cable of 11 KV grade of following size direct in ground in the same trench in one tier horizontal formation including excavation, sand cushioning, protective covering and refilling the trench etc as required. 8.2 (-2013) ii) Above 120sqmm and upto 400 sqmm. 100 M 182.00 18,200.00 8.2.2 2.0 Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 11 KV grade of following size in the existing RCC/HUME/ METAL pipe as required. 8.3 (-2013) i) Above 120sqmm and upto 400 sqmm. 40 M 53.00 2,120.00 8.3.2 3.0 Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 11 KV grade of following size in the existing masonry open duct as required. 8.4 (-2013) i) Above 120sqmm and upto 400 sqmm. 150 M 45.00 6,750.00 8.4.2 4.0 Supplying and making indoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required : 10.4 (-2013) i) 240 sq.mm 4 Set 7,007.00 28,028.00 10.4.3 Page 1 of 16

Description Qty. Unit NON- Amount as per Amount as per NON -2013 / ii) 400 sq.mm 2 Set 11,678.00 23,356.00 DR/ 5.0 11 KV H.T. FOUR (4) BREAKER SWITCHBOARD PANEL (SUBSTATION - 1) Supplying, installation, testing & commissioning of indoor type floor mounted metal clad, 11KV VCB panel with 4 No. VCBs, totally enclosed and fully interlocked, horizontal drawout, horizontal / vertical isolation type breaker as per IS 13118, as amended up to date and additional specifications, having capacities as mentioned below, single break, trip free mechanism, motorised / manually charged and auto / manually closing breaker suitable for use on 11 KV, 3 Phase, 50Hz A.C. supply with short circuit fault level of 350 MVA, complete with self contained, fully interlocked, rack in and rack out mechanism, air insulated but encapsulated copper bus bars of 800 Amps capacity, breaker featured with mechanical ON/OFF indicator with hand trip device, spring release coil, shunt trip coil and auxiliary switch of 4 NO+4NC and equipped with following switchgears and accessories i/c connections suitable for 3 core 400 sq.mm XLPE 11KV cable (cable entry from bottom / top / side), end termination with heat shrinkable joint(6 metre length) including 80mm thick glass wool insulation with aluminium cladding 26 guage aluminium sheet, electric starter, batteries & ba 1 Set 2,037,000.00 2,037,000.00 () A) INCOMING PANEL - 2 NO. (EACH CONSISTING OF FOLLOWING) i) 1 No. 350 MVA, 630Amp 11KV, Vacuum Circuit Breaker with motorised spring charged and manual closing mechanism. Shunt trip coil shall operate in 110V DC voltage derived through a power pack. ii) 3 No. Single Phase double core double ratio current transformer 300/150/5/5Amp epoxy cast insulated class of insulation E. Core 1-15VA burden class 0.5 for metering. Core 2-15VA burden class 5P10 for protection. iii) 3 Nos. Line PT 11KV/ Ö3, 110V/ Ö3, 100VA burden of class 0.5 epoxy cast resin type with 1 No. voltmeter (0-15KV), analog / digital type, selector switch with voltmeter & protection mcb for H.T. Metering upto 12KV on incomer. iv) 1 No. Microprocessor based Numerical relay with O/L, S/C & E/F protection. (over load setting 20-200% and E/F setting 5-80%). v) 1 No. Anti Pumping device. vi) vii) 1No.Circuit breaker control switch for electrical (T/N/C). 1No. limit switch for test & service position. Page 2 of 16

Description Qty. Unit NON- Amount as per Amount as per NON -2013 / viii) 1 No. digital type Ammeter (0-300Amp) (96mm square) with selector switch. ix) 1 No. electronic type digital energy analyser having minimum 30 days memory and parameters of voltage, current, frequency, KW, KVA, KVAr, PF Power factor etc. shall be suitable for BMS operation with 485 port MODBUS output protocol. x) 1 Set of following indicating lamps. - Red, Yellow & Blue for phase indication. - Amber for Trip indication. - Red `ON' Green `OFF' - Spring charge indication. - Auto trip indication. xi) xii) 1 No. Power pack for trip coil operation. 1 No. control Transformer of 11KV/415-230Volts AC of 1KVA capacity for auxillary supply for breaker closing coil, indicating lamps, space heaters etc. control transformer shall be epoxy cast resin dry type and the connection for control transformer shall be taken from the cable side before the circuit breaker tapping. xiii) xiv) xv) xvi) 1 No. hooter. 1 No. master trip relay. 1 No. over voltage relay. 1 Set of fuses, ferrules, wiring etc. as required. xvii) Brass gland suitable for 1 No. 3 core 400Sq.mm. 11KV XLPE aluminium armoured cable. B) OUTGOING PANEL - 2 NOS. (EACH CONSISTING OF FOLLOWING) i) 1 No. 350MVA, 630Amp 11KV, Vacuum Circuit Breaker with motorised spring charged and manual closing mechanism. Shunt trip coil shall operate on 110V DC voltage derived through a power pack. ii) 3 No. Single Phase double core current transformer 50/5 Amp epoxy cast insulated class of insulation E. - Core 1-15VA burden class-1.0 for metering. - Core 2-15VA burden class 5P10 for protection. Page 3 of 16

Description Qty. Unit NON- Amount as per Amount as per NON -2013 / iii) 1 No. Microprocessor based Numerical relay with O/L, S/C & E/F protection. (Relay shall be for highset instantaneous protection for over current & earth fault). iv) 1 No. Anti Pumping device. v) 1 No. Auxiliary relay (VAA33) for transformer fault, alarm and trip suitable for 230 V AC Supply. vi) vii) viii) ix) 1 No. Circuit breaker control switch for electrical (T/N/C). 1 No. limit switch for test & service position. 1 No. digital type Ammeter of range 0-50 Amp (96mm Square). 1 Set of following indicating lamps (LED Type). - Red, Yellow & Blue for phase indication. - Red 'ON' Green 'OFF'. - Amber for trip indication. - Spring charge indication. - Auto trip indication. x) 1 Set of fuses, ferrules, wiring etc. as required. xi) xii) xiii) xiv) 1 No. hooter. 1 No. master trip relay. 1 No. power pack for trip coil operation. Brass gland suitable for 1 No. 3 core 240sq.mm 11KV XLPE aluminium armoured cable. - All metering and protection devices, interconnections, necessary control wiring and all other accessories shall be provided as per specifications, technical requirement of local electric supply authority. TOTAL OF SUBHEAD I - HT CABLE & VACUUM CIRCUIT BREAKER CARRIED OVER TO THE SUMMARY. 104,054.00 2,037,000.00 II. DISTRIBUTION TRANSFORMER & BUS TRUNKING 1.0 DISTRIBUTION TRANSFORMER (OIL TYPE) (OLTC TYPE) Page 4 of 16

Description Qty. Unit NON- Amount as per Amount as per NON -2013 / Supply, installation, testing & commissioning of 800 KVA 11KV/433V, 3 phase 50 Hz outdoor copper wound oil type distribution transformer with OLTC (On Load Tap Changer) with AVR and RTCC Panel. Vector group Dyn-11 ONAN cooled having cable end box suitable for 3 core 240 sq.mm XLPE Aluminium conductor 11KV cable on HV & multicore aluminium XLPE cable on L.T. side with all fittings & accessories, bucholtz relay alarm & trip, WTI alarm & trip and oil temperature alarm & trip control wiring, all civil work including foundation etc. complete as per specifications & conforming to IS 2026-1977 and complying with specification and requirement of local electric supply authority. 2 No. 1,557,000.00 3,114,000.00 () 2.0 BUS TRUNKING Supply, installation, testing & commissioning of following capacity / rating prefabricated Air insulated bus trunking / Bus Duct suitable for 415 volts 3 phase, 4 wire 50Hz AC supply system (Between Transformer L.T. side and incomer of L.T. Panel side) of aluminium busbars complete with bends, expansion joints, fire barriers, copper fexible end connection at both ends, Earthing with 2 runs of copper / aluminium earth of size 25mm x 5mm strip etc. including necessary support etc. as per specification and as required. 3.5 (-2013) a) Bus Trunking i) 1250 Amp 50 M 12,235.00 611,750.00 3.5.3 b) Copper Flexible for Bus Trunking (Average length 320mm) i) 1250 Amp 4 Set 35,000.00 140,000.00 () (Note: The bus trunking shall be measured along the length of enclosure. The aluminium/ copper strips which will go inside LT panels & end termination box of transformers shall not be taken into measurement of bus trunking quantity). TOTAL OF SUBHEAD II - DISTRIBUTION TRANSFORMER & BUS TRUNKING CARRIED OVER TO SUMMARY. 611,750.00 3,254,000.00 III. DG SETS & ACCESSORIES Page 5 of 16

Description Qty. Unit NON- Amount as per Amount as per NON -2013 / 1.0 Supply, installation, testing and commissioning of 200 KVA, 415 Volt, 3 phase, 1500 R.P.M, 0.8 PF radiator with fan cooled, floor mounted Diesel Generator set complete with Alternator of 200 KVA, 415 Volt AC. Engine Coupled to Alternator housed in acoustic enclosure conforming to latest environment protection regulations for emmission and noise levels complete with Diesel Engine developing either 246 BHP at 1500 RPM or actual BHP calculated considering de-rating factor if any whichever is higher Alternator and all accessories including supply and installation of Engine control panel with meters, CTs and transducers for all metering and protection, AMF Panel suitable for auto start / stop of DG Set, Auto changeover of gird and DG supply, interlocking with required switchgear, contactor (AC3 duty), Instrument, relay, timer etc. complete, antivibration mountings, hospital type silencer, flexible pipe connections, exhaust piping with bends etc. (6 metre length) including 80mm thick glass wool insulation with aluminium cladding 26 guage aluminium sheets, electric starter, batteries & battery charger, fuel tank of 990 ltrs.capacity with level indicator, radiator, control wiring, first fill of lubricating oil, and Diesel for testing and commissioning and all spares and accessories as required complete with necessary civil work such as grouting, chipping, finishing etc.as required complete including foundation (Foundation to be paid and measured under separate item) (Foundation to be done by the Contractor based on DG Set manufacturer Shop Drawing). The work should be as per Central Electrical Inspectorate/ Pollution control board standards. (Refer Technical Specification) 1 No. 1,867,000.00 1,867,000.00 () Page 6 of 16

Description Qty. Unit NON- Amount as per Amount as per NON -2013 / 2.0 Supply, installation, testing and commissioning of 250 KVA, 415 Volt, 3 phase, 1500 R.P.M, 0.8 PF water cooled, radiator type floor mounted Diesel Generator set complete with Alternator of 250 KVA, 415 Volt AC. Engine Coupled to Alternator housed in acoustic enclosure conforming to latest environment protection regulations for emmission and noise levels complete with Diesel Engine developing either 310 BHP at 1500 RPM or actual BHP calculated considering de-rating factor if any whichever is higher alternator considering de-rating factor if any whichever is higher alternator and all accessories including supply and installation of Engine control panel with meters, CTs and transducers for all metering and protection, AMF Panel suitable for auto start / stop of DG Set, Auto changeover of gird and DG supply interlocking with required switchgear, contactor (AC3 duty), Instrument, relay, timer etc. complete, antivibration mountings, hospital type silencer, flexible pipe connections, exhaust piping with bends etc. (6 metre length) including 80mm thick glass wool insulation with aluminium cladding 26 guage aluminium sheet, electric starter, batteries & battery charger, fuel tank of 990 ltrs. capacity with level indicator, radiator, control wiring, first fill of lubricating oil, and Diesel for testing and commissioning and all spares and accessories as required complete with necessary civil work such as grouting, chipping, finishing etc.as required complete including foundation (Foundation to be paid and measured under separate item) (Foundation to be done by the Contractor based on DG Set manufacturer Shop Drawing). The work should be as per Central Electrical Inspectorate/ Pollution control board standards. (Refer Technical Specification) 1 No. 2,211,000.00 2,211,000.00 () TOTAL OF SUBHEAD III - DG SETS & ACCESSORIES CARRIED OVER TO THE SUMMARY. 0.00 4,078,000.00 IV. MAIN L.T. PANELS, CAPACITOR BANK PANELS & SUB-DISTRIBUTION BOARDS 1.0 MAIN L.T. PANEL (NORMAL SUPPLY) (SS1/MLTP) Page 7 of 16

Description Qty. Unit NON- Amount as per Amount as per NON -2013 / Supply, installation, testing & commissioning of Main L.T. Panel extensible type suitable for 415 volts (nominal) 3 phase 4 wire, 50 Hz, A.C. Supply totally enclosed type with free standing floor mounted dust and vermin proof compartmentalised indoor type fabricated from 2mm thick CRCA sheet steel complete with busbars, ammeter, ammeter selector switch, voltmeter, voltmeter selector switch, indicating lamps, protection relays, CT's, protection fuses, interconnections with suitable size of copper leads/solid aluminium strips/rod and having following incoming and outgoing Air Circuit Breakers, MCCB's as per the drawing and technical specifications complete as required. (TOTAL OF A TO D) 1 Set 1,825,000.00 1,825,000.00 () A) INCOMER BREAKERS 2 Nos. 1250Amp FP Manually operated horizontal drawout type (MDO) Air Circuit Breaker (50KA) with microprocessor release,o/l, S/C & E/F protection with communication port RS485 port (Transformer Incomer). B) BUSCOUPLER BREAKERS 1 No. 1250Amp FP Manually operated horizontal drawout type (MDO) Air Circuit Breaker (50KA) as buscoupler with interlocking arrangement with incomers ACB. 1 Set of indicating lamps for ON & OFF of buscoupler. C) BUSBARS 1600 Amp TPN busbars of aluminium alloy (Bus-Section I & II). D) OUTGOING BREAKERS WITH INSTRUMENTS 6 Nos. 800 Amp Three Pole Manually operated horizontal drawout type (MDO) Air Circuit Breaker (50KA) with thermal magnetic release, with O/L, S/C & E/F protection & neutral link. 4 Nos. 630 Amp Three Pole Moulded Case Circuit Breaker (35KA Ics Value) with microprocessor release for O/L, S/C & E/F protection & neutral link. 2 No. 400 Amp Three Pole Moulded Case Circuit Breaker (35KA Ics Value) with microprocessor release for O/L, S/C & E/F protection & neutral link. E) INSTRUMENTS & RELAYS ON INCOMER BREAKERS 2 Nos. 0 to 500 Volt digital voltmeter with selector switch (96mm square) (one for each incoming breaker). Page 8 of 16

Description Qty. Unit NON- Amount as per Amount as per NON -2013 / 2 Nos. 0 to 1250 Amp digital ammeter (96mm square) with CT's (one for each incoming breaker) and selector switch. 2 Sets of phase indicating lights (RYB) with protection mcb's (one set for each incoming breaker). 2 Sets breaker 'ON' & 'OFF' indicating lamp (one set for each incoming breaker). 2 Sets trip circuit healthy indicating lamp (one set for each incoming breaker). 2 Sets auto trip indicating lamp (one set for each incoming breaker). 2 Nos. of Dual ratio CT's of 1250/300/5/5Amp ratio each for APFC Relay (one for each incoming breaker). 2 Nos. trip circuit supervision relay (one for each incoming breaker). 2 Nos. electronic type Digital energy analyser having 30 day memory and parameters of KW, KWH, power factor, frequency etc. (one for each incoming breaker). 2 Nos. Phase squence relay (one for each incoming breaker). 2 Nos. master trip relay (one for each incoming breaker). 2 Set of O/V & U/V relay (one for each incoming breaker). 2.0 CAPACITOR BANK PANEL (200 KVAR) Supply, installation, testing & commissioning of Capacitor Panel suitable for 415 volts (nominal) 3 phase 4 wire, 50 Hz, A.C. Supply totally enclosed type with free standing floor mounted dust and vermin proof indoor type fabricated from 2mm thick CRCA sheet steel complete with busbars, ammeter, ammeter selector switch, voltmeter, voltmeter selector switch, indicating lamps, protection relays, CT's protection fuses, interconnections with suitable size of copper leads/solid aluminium strips/rod auto / manual selector switch for operation of capacitor units, push buttons for manual operation capacitor duty, contractors capacitor bank, APFC relay, power factor meter etc. complete and having following incoming and outgoing Circuit Breakers etc. as per the drawing and specifications complete as required. (TOTAL OF A TO C) 2 Set 351,000.00 702,000.00 A) INCOMER 1 No. 630 Amp FP Moulded Case Circuit Breaker (35KA Ics Value) with microprocessor release for O/L, S/C & E/F protection. 1 No. 0-630A. Ammeter with selector switch & CT's. 1 No. 0-500A. Voltmeter with selector switch. Page 9 of 16

Description Qty. Unit NON- Amount as per Amount as per NON -2013 / 1 Set of phase indicating lamps B) BUSBARS 700A TPN Aluminium busbars C) OUTGOING 14 stepped Automatic Power Factor Correction relay (APFC relay). 4 Nos. 63 Amp TP Moulded Case Circuit Breaker (25KA Ics Value) with neutral link. 10 Nos. 32 Amp TP Moulded Case Circuit Breaker (25KA Ics Value) with neutral link. 14 Nos. Capacitor duty contactor (one for each 25KVAR / 10KVAR) Capacitor unit. 4 Nos. 25 KVAR Capacitor Bank. 10 Nos. 10 KVAR Capacitor Bank. 14 sets of push button stations Red and Green for manual operation of capacitor units with auto/manual selector switches. 1 No. Indicating lamp for each 25 KVAR / 10 KVAR capacitor unit to indicate that the unit is 'ON'. 1 No. Toggle switch for changing automatic to manual operation of capacitor units. 1 No. Power factor meter. 3.0 MAIN L.T. PANEL (ESSENTIAL SUPPLY) (SS1/EMLTP) Supply, installation, testing & commissioning of Main L.T. Panel (Essential Supply) extensible type suitable for 415 volts (nominal) 3 phase 4 wire, 50 Hz, A.C. Supply totally enclosed type with free standing floor mounted dust and vermin proof compartmentalised indoor type fabricated from 2mm thick CRCA sheet steel complete with busbars, ammeter, ammeter selector switch, voltmeter, Page 10 of 16

Description Qty. Unit NON- Amount as per Amount as per NON -2013 / voltmeter selector switch, indicating lamps, protection relays, CT's protection fuses, interconnections with suitable size of copper leads/solid aluminium strips/rod. PLC shall be provided for monitering power supply on various bus section and closing / opening of incomer & bus coupler breakers and interlocking of incomer and bus coupler breakers and having following incoming and outgoing Air Circuit Breakers, MCCB's as per the drawing and technical specifications complete as required. (TOTAL OF A TO E) 1 Set 679,000.00 679,000.00 () A) INCOMER BREAKERS 2 Nos. 400Amp FP Moulded Case Circuit Breaker (35KA Ics Value) with microprocessor release for O/L, S/C & E/F protection. 2 Nos. 400Amp FP contactor (AC 3 Duty) with timer switch. B) AUTO OPERATION OF INCOMER / BUSCOUPLER ACB's. i) Load management through Micro PLC shall be provided to achieve the following functions. ii) Auto changeover between incomer breakers. iii) Buscoupler switching. iv) Signal to AMF Panel for status of 'Load' to ensure auto stop / auto start of DG Set by AMF Panel. v) Interlocking of incomer and bus coupler breakers. vi) Necessary hardware shall be provided to achieve above functions including micro PLC with real time clock, digital inputs / outputs, MMI with 2 line display, power supply, auxillary relays, push buttons, LED indication lamp, window announciation facia etc. & software for the above. All items required for complete operation whether or not list in BOQ shall deemed to be included in quoted rates. vii) Automatic system shall be user friendly and shall have manual over ride. C) BUSCOUPLER BREAKERS - 1 No. 400Amp FP Contactor as buscoupler. - 1 Set of indicating lamps for ON & OFF of buscoupler. D) BUSBARS i) 600 Amp TPN busbars of aluminium alloy in Bus Section - I & II. E) OUTGOING BREAKERS WITH INSTRUMENTS Page 11 of 16

Description Qty. Unit NON- Amount as per Amount as per NON -2013 / i) 2 Nos. 250 Amp Three Pole Moulded Case Circuit Breaker (35KA Ics Value) with microprocessor release for O/L, S/C & E/F protection and neutral link. ii) 2 Nos. 200 Amp Three Pole Moulded Case Circuit Breaker (35KA Ics Value) with thermal magnetic release, O/L, S/C & E/F protection and neutral link. iii) 2 Nos. 125 Amp Three Pole Moulded Case Circuit Breaker (35KA Ics Value) with thermal magnetic release, O/L, S/C & E/F protection and neutral link. iv) 2 Nos. 63 Amp Three Pole Moulded Case Circuit Breaker (25KA Ics Value) with thermal magnetic release, O/L, S/C & E/F protection and neutral link. F) INSTRUMENTS ON INCOMER BREAKERS i) 2 Nos. 0 to 500 Volt digital voltmeter with selector switch (96mm square) (one for each incoming breaker). ii) 2 Nos. 0 to 400 Amp digital ammeter (96mm square) with CT's and selector switch. iii) iv) 2 Sets of phase indicating lights (RYB) with protection mcb's (one set for each incoming breaker). 2 Sets breaker 'ON' & 'OFF' indicating lamp (one set for each incoming breaker). v) 2 Nos. electronic type Digital energy analyser having 30 day memory and parameters of KW, KWH, power factor, frequency etc. (one for each incoming breaker). 4.0 SDB - DISTRIBUTION BOARDS Supply, installation, testing & commissioning of cubicle type tollally enclosure free standing type moistue, dust and vermin proof Sub Distribution Boards (SDB) made out of 2mm thick CRCA sheet steel complete with following equipments, including ammeter, ammeter selector switch, voltmeter, voltmeter selector switch, indicating lamps, CT's internal wiring with suitable size wires / cable, interconnection, pointing etc. as per drawing and specification complete as required. 4.1 ESDB/SS1 (TOTAL OF A TO D) 1 Set 107,000.00 107,000.00 () A) INCOMING 1 No. 125Amp FP Moulded Case Circuit Breaker of (35KA Ics Value) with thermal magnetic release and O/L, S/C & E/F protection. Page 12 of 16

Description Qty. Unit NON- Amount as per Amount as per NON -2013 / B) INSTRUMENTS 1 No. 0 to 500 Volt digital voltmeter (96mm square) with selector switch. 1 No. 0 to 125 Amp digital ammeter (96mm square) with selector switch & CT's. 1 Set of phase indicating lights (RYB) with protection MCB. C) BUSBARS 150Amp TPN busbars of aluminium alloy. D) OUTGOING 2 Nos. 100 Amp TP Moulded Case Circuit Breaker of (25KA Ics Value) with thermal magnetic release, O/L & S/C protection and neutral link. 3 Nos. 32-63 Amp TP Moulded Case Circuit Breaker of (25KA Ics Value) with thermal magnetic release, O/L & S/C protection and neutral link. TOTAL OF SUBHEAD IV - MAIN LT PANELS, CAPACITOR BANK PANELS & SUB-DISTRIBUTION BOARDS CARRIED OVER TO THE SUMMARY. 0.00 3,313,000.00 V. LT CABLES 1.0 Supply of following size of 1.1KV grade multicore aluminium conductor XLPE / PVC insulated & PVC sheathed armoured cable as per IS: 7098 (Part-1) 1988 complete as required. i) 3.5 core, 50 Sq.mm. 220 M. 303.00 66,660.00 () 2.0 Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. 7.1 (-2013) i) Upto 35 sq. mm 200 M. 181.00 36,200.00 7.1.1 (Part of sec.- B) ii) Above 35 sq. mm and upto 95 sq. mm 220 M. 188.00 41,360.00 7.1.2 Page 13 of 16

Description Qty. Unit NON- Amount as per Amount as per NON -2013 / ii) Above 95 sq. mm and upto 185 sq. mm 50 M. 195.00 9,750.00 7.1.3 iii) Above 185 sq. mm and upto 400 sq. mm 150 M. 215.00 32,250.00 7.1.4 3.0 Laying of one number additional PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground in the same trench in one tier horizontal formation including excavation, sand cushioning, protective covering and refilling the trench etc as required. 7.2 (-2013) i) Upto 35 sq. mm 250 M. 124.00 31,000.00 7.2.1 ii) Above 95 sq. mm and upto 185 sq. mm 100 M. 138.00 13,800.00 7.2.3 iii) Above 185 sq. mm and upto 400 sq. mm 300 M. 159.00 47,700.00 7.2.4 4.0 Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required. 7.5 (-2013) i) Upto 35 sq. mm 36 M. 15.00 540.00 7.5.1 ii) Above 95 sq. mm and upto 185 sq. mm 20 M. 30.00 600.00 7.5.3 iii) Above 185 sq. mm and upto 400 sq. mm 48 M. 53.00 2,544.00 7.5.4 5.0 Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing masonry open duct as required. 7.6 (-2013) i) Upto 35 sq. mm 20 M. 11.00 220.00 7.6.1 ii) Above 35 sq. mm and upto 95 sq. mm 20 M. 18.00 360.00 7.6.2 iii) Above 95 sq. mm and upto 185 sq. mm 20 M. 25.00 500.00 7.6.3 iv) Above 185 sq. mm and upto 400 sq. mm 30 M. 45.00 1,350.00 7.6.4 6.0 Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface / cable Tray as required. 7.7 (-2013) i) Upto 35 sq. mm (clamped with 1mm thick saddle) 60 M. 22.00 1,320.00 7.7.1 ii) iii) Above 95 sq. mm and upto 185 sq. mm (clamped with 25/40x3mm MS flat clamp) Above 185 sq. mm and upto 400 sq. mm (clamped with 40x3mm MS flat clamp) 100 M. 77.00 7,700.00 7.7.3 220 M. 107.00 23,540.00 7.7.4 Page 14 of 16

Description Qty. Unit NON- Amount as per Amount as per NON -2013 / 7.0 Suppling and making indoor end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 9.1 (-2013) i) 3.5 core, 400 Sq.mm. 12 Set 1,203.00 14,436.00 9.1.31 ii) 3.5 core, 300 Sq.mm. 12 Set 940.00 11,280.00 9.1.30 iii) 3.5 core, 150 Sq.mm. 4 Set 501.00 2,004.00 9.1.26 iv) 3.5 core, 50 Sq.mm. 4 Set 286.00 1,144.00 9.1.22 v) 4 core, 16 Sq.mm. 2 Set 208.00 416.00 9.1.33 8.0 Supply and installing following size of perforated M.S. cable trays with perforation not more than 17.5% in convenient sections, joints with connectors suspended from the ceiling with M.S. suspenders and including bolts & nuts, painting suspenders etc. as per specification and as required. 4.1 (-2013) i) 150 mm width X 50 mm depth X 1.6 mm thickness 30 M. 523.00 15,690.00 4.1.2 ii) 300 mm width X 50 mm depth X 1.6 mm thickness 40 M. 756.00 30,240.00 4.1.4 (Part of sec.- B) iii) 600 mm width X 50 mm depth X 2.0 mm thickness 45 M. 1,338.00 60,210.00 4.1.7 TOTAL OF SUBHEAD V - LT CABLES CARRIED OVER TO THE SUMMARY. 386,154.00 66,660.00 VI. EARTHING 1.0 Providing and fixing 25 mm X 5 mm copper strip in 40 mm dia G.I. pipe from earth electrode including connection with brass nut, bolt, spring, washer excavation and refilling etc. as required. 2.0 Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe from earth electrode including connection with G.I. nut, bolt, spring, washer excavation and refilling etc. as required. 60 M. 1,019.00 80 M. 391.00 61,140.00 5.10 (-2013) 31,280.00 5.11 (-2013) Page 15 of 16

Description Qty. Unit NON- Amount as per Amount as per NON -2013 / 3.0 Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as required. 70 M. 812.00 56,840.00 5.14 (-2013) 4.0 Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required. 130 M. 133.00 17,290.00 5.15 (-2013) 5.0 Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required. 50 M. 34.00 1,700.00 5.16 (-2013) TOTAL OF SUBHEAD VI - EARTHING CARRIED OVER TO THE SUMMARY. 168,250.00 0.00 Page 16 of 16

TENDER FOR BALANCE WORK OF SUPPLY, INSTALLATION, TESTING & COMMISSIONING OF TWO NO. 11/0.433KV INDOOR ELECTRIC SUBSTATION (ESS-1&2), THREE NO. OUTDOOR TYPE 11/0.433KV COMPACT SUB-STATION (CSS-1,2&3) AND OTHER ASSOCIATED EXTERNAL ELECTRICAL WORKS FOR THE PERMANENT CAMPUS OF THE CENTRAL UNIVERSITY OF JAMMU (CUJ) AT VILLAGE BAGLA, DISTT. SAMBA (J&K). SECTION - B: ABSTRACT COST FOR BALANCE WORK OF POWER SUPPLY PACKAGE FOR SUBSTATION II & COMPACT TYPE SUBSTATION (CSS) (POWER SUPPLY PACKAGE & EXTERNAL ELECTRICAL WORKS) Description Qty. Unit NON- Amount as per Amount as per NON -2013 / I. H.T. CABLE & VACUUM CIRCUIT BREAKERS 1.0 Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 11KV grade of following sizes direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc. as required. 8.1 (-2013) i) Above 120sqmm and upto 400 sqmm. 750 M 256.00 192,000.00 8.1.2 2.0 Laying of one number additional PVC insulated and PVC sheathed / XLPE power cable of 11 KV grade of following size direct in ground in the same trench in one tier horizontal formation including excavation, sand cushioning, protective covering and refilling the trench etc as required. i) Above 120sqmm and upto 400 sqmm. 1200 M 182.00 218,400.00 8.2.2 8.2 (-2013) 3.0 Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 11 KV grade of following size in the existing RCC/HUME/ METAL pipe as required. 8.3 (-2013) i) Above 120sqmm and upto 400 sqmm. 80 M 53.00 4,240.00 8.3.2 4.0 Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 11 KV grade of following size in the existing masonry open duct as required. 8.4 (-2013) i) Above 120sqmm and upto 400 sqmm. 1500 M 45.00 67,500.00 8.4.2 Page 1 of 21

Description Qty. Unit NON- Amount as per Amount as per NON -2013 / 5.0 Supplying and making indoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required : 10.4 (-2013) i) 240 sq.mm 4 Set 7,007.00 28,028.00 10.4.3 ii) 400 sq.mm 10 Set 11,678.00 116,780.00 DR/ 6.0 11 KV H.T. FOUR (4) BREAKER SWITCHBOARD PANEL (SUBSTATION - 2) Supplying, installation, testing & commissioning of indoor type floor mounted metal clad, 11KV VCB panel with 4 No. VCBs, totally enclosed and fully interlocked, horizontal drawout, horizontal / vertical isolation type breaker as per IS 13118, as amended up to date and additional specifications, having capacities as mentioned below, single break, trip free mechanism, motorised / manually charged and auto / manually closing breaker suitable for use on 11 KV, 3 Phase, 50Hz A.C. supply with short circuit fault level of 350 MVA, complete with self contained, fully interlocked, rack in and rack out mechanism, air insulated but encapsulated copper bus bars of 800 Amps capacity, breaker featured with mechanical ON/OFF indicator with hand trip device, spring release coil, shunt trip coil and auxiliary switch of 4 NO+4NC and equipped with following switchgears and accessories i/c connections suitable for 3 core 400 sq.mm XLPE 11KV cable (cable entry from bottom / top / side), end termination with heat shrinkable jointing material etc. and complete as per specification as required. (Note :- Cost of end termination not included in this item) (TOTAL OF A & B) A) INCOMING PANEL - 2 NO. (EACH CONSISTING OF FOLLOWING) 1 Set 2,029,000.00 2,029,000.00 () i) 1 No. 350 MVA, 630Amp 11KV, Vacuum Circuit Breaker with motorised spring charged and manual closing mechanism. Shunt trip coil shall operate in 110V DC voltage derived through a power pack. Page 2 of 21

Description Qty. Unit NON- Amount as per Amount as per NON -2013 / ii) 3 No. Single Phase double core double ratio current transformer 300/150/5/5Amp epoxy cast insulated class of insulation E. Core 1-15VA burden class 0.5 for metering. Core 2-15VA burden class 5P10 for protection. iii) 3 Nos. Line PT 11KV/ 3, 110V/ 3, 100VA burden of class 0.5 epoxy cast resin type with 1 No. voltmeter (0-15KV), analog / digital type, selector switch with voltmeter & protection mcb for H.T. Metering upto 12KV on incomer. iv) 1 No. Microprocessor based Numerical relay with O/L, S/C & E/F protection. (over load setting 20-200% and E/F setting 5-80%). v) 1 No. Anti Pumping device. vi) vii) viii) 1No.Circuit breaker control switch for electrical (T/N/C). 1No. limit switch for test & service position. 1 No. digital type Ammeter (0-300Amp) (96mm square) with selector switch. ix) 1 No. electronic type digital energy analyser having minimum 30 days memory and parameters of voltage, current, frequency, KW, KVA, KVAr, PF Power factor etc. shall be suitable for BMS operation with 485 port MODBUS output protocol. x) 1 Set of following indicating lamps. - Red, Yellow & Blue for phase indication. - Amber for Trip indication. - Red `ON' Green `OFF' - Spring charge indication. - Auto trip indication. xi) 1 No. Power pack for trip coil operation. xii) 1 No. control Transformer of 11KV/415-230Volts AC of 1KVA capacity for auxillary supply for breaker closing coil, indicating lamps, space heaters etc. control transformer shall be epoxy cast resin dry type and the connection for control transformer shall be taken from the cable side before the circuit breaker tapping. xiii) 1 No. hooter. Page 3 of 21

Description Qty. Unit NON- Amount as per Amount as per NON -2013 / xiv) 1 No. master trip relay. xv) 1 No. over voltage relay. xvi) 1 Set of fuses, ferrules, wiring etc. as required. xvii) Brass gland suitable for 1 No. 3 core 400Sq.mm. 11KV XLPE aluminium armoured cable. B) OUTGOING PANEL - 2 NOS. (EACH CONSISTING OF FOLLOWING) i) 1 No. 350MVA, 630Amp 11KV, Vacuum Circuit Breaker with motorised spring charged and manual closing mechanism. Shunt trip coil shall operate on 110V DC voltage derived through a power pack. ii) 3 No. Single Phase double core current transformer 90/5 Amp epoxy cast insulated class of insulation E. - Core 1-15VA burden class-1.0 for metering. - Core 2-15VA burden class 5P10 for protection. iii) 1 No. Microprocessor based Numerical relay with O/L, S/C & E/F protection. (Relay shall be for highset instantaneous protection for over current & earth fault). iv) 1 No. Anti Pumping device. v) 1 No. auxiliary relay (VAA33) for transformer fault, alarm and trip suitable for 230 V AC Supply. vi) vii) viii) ix) 1 No. Circuit breaker control switch for electrical (T/N/C). 1 No. limit switch for test & service position. 1 No. digital type Ammeter of range 0-100 Amp (96mm Square). 1 Set of following indicating lamps (LED Type). - Red, Yellow & Blue for phase indication. - Red 'ON' Green 'OFF'. - Amber for trip indication. - Spring charge indication. - Auto trip indication. xi) xii) 1 Set of fuses, ferrules, wiring etc. as required. 1 No. hooter. Page 4 of 21

Description Qty. Unit NON- Amount as per Amount as per NON -2013 / xiii) xiv) xv) 1 No. master trip relay. 1 No. power pack for trip coil operation. Brass gland suitable for 1 No. 3 core 240sq.mm 11KV XLPE aluminium armoured cable. - All metering and protection devices, interconnections, necessary control wiring and all other accessories shall be provided as per specifications, technical requirement of local electic supply authority. TOTAL OF SUBHEAD I - HT CABLE & VACUUM CIRCUIT BREAKER CARRIED OVER TO THE SUMMARY. 626,948.00 2,029,000.00 II. DISTRIBUTION TRANSFORMER & BUS TRUNKING DISTRIBUTION TRANSFORMER (OIL TYPE) (OLTC TYPE) 1.0 Supply, installation, testing & commissioning of 1600 KVA 11KV/433V, 3 phase 50 Hz indoor copper wound oil type distribution transformer with OLTC (On Load Tap Changer) with AVR and RTCC Panel. Vector group Dyn-11 ONAN cooled having cable end box suitable for 3 core 240 sq.mm XLPE Aluminium conductor 11KV cable on HV & Aluminium Bus Trunding / Bus Duct on L.T side with all fittings & accessories, bucholtz relay alarm & trip, WTI alarm & trip and oil temperature alarm & trip control wiring, all civil work including foundation etc. complete as per specifications & conforming to IS 2026-1977 and complying with specification and requirement of local electric supply authority. 2 No. 2,302,000.00 4,604,000.00 () 2.0 BUS TRUNKING Page 5 of 21

Description Qty. Unit NON- Amount as per Amount as per NON -2013 / Supply, installation, testing & commissioning of following capacity / rating prefabricated Air insulated bus trunking / Bus Duct suitable for 415 volts 3 phase, 4 wire 50Hz AC supply system (Between Transformer L.T. side and incomer of L.T. Panel side) of aluminium busbars complete with bends, expansion joints, fire barriers, copper fexible end connection at both ends, Earthing with 2 runs of copper / aluminium earth of size 25mm x 5mm strip etc. including necessary support etc. as per specification and as required. 3.5 (-2013) a) Bus Trunking ii 2500 Amp 50 M 32,000.00 1,600,000.00 () b) Copper Flexible for Bus Trunking (Average length 320mm) i) 2500 Amp 4 Set 84,000.00 336,000.00 () (Note: The bus trunking shall be measured along the length of enclosure. The aluminium/ copper strips which will go inside LT panels & end termination box of transformers shall not be taken into measurement of bus trunking quantity). TOTAL OF SUBHEAD II - DISTRIBUTION TRANSFORMER & BUS TRUNKING CARRIED OVER TO SUMMARY. 0.00 6,540,000.00 III. DG SETS & ACCESSORIES Page 6 of 21

Description Qty. Unit NON- Amount as per Amount as per NON -2013 / 1.0 Supply, installation, testing and commissioning of 250 KVA, 415 Volt, 3 phase, 1500 R.P.M, 0.8 PF radiator with fan cooled, floor mounted Diesel Generator set complete with Alternator of 250 KVA, 415 Volt AC. Engine Coupled to Alternator housed in acoustic enclosure conforming to latest environment protection regulations for emmission and noise levels complete with Diesel Engine developing either 310 BHP at 1500 RPM or actual BHP calculated considering de-rating factor if any whichever is higher Alternator and all accessories including supply and installation of Engine control panel with meters, CTs and transducers for all metering and protection, AMF Panel suitable for auto start / stop of DG Set, Auto changeover of gird and DG supply, interlocking with required switchgear, contactor (AC3 duty), Instrument, relay, timer etc. complete, antivibration mountings, hospital type silencer, flexible pipe connections, exhaust piping with bends etc. (6 metre length) including 80mm thick glass wool insulation with aluminium cladding 26 guage aluminium sheets, electric starter, batteries & battery charger, fuel tank of 990 ltrs. capacity with level indicator, radiator, control wiring, first fill of lubricating oil, and Diesel for testing and commissioning and all spares and accessories as required complete with necessary civil work such as grouting, chipping, finishing etc.as required complete including foundation (Foundation to be paid and measured under separate item) (Foundation to be done by the Contractor based on DG Set manufacturer Shop Drawing). The work should be as per Central Electrical Inspectorate/ Pollution control board standards. (Refer Technical Specification) 1 No. 2,211,000.00 2,211,000.00 () TOTAL OF SUBHEAD III - DG SETS & ACCESSORIES CARRIED OVER TO THE SUMMARY. 0.00 2,211,000.00 IV. MAIN L.T. PANELS, CAPACITOR BANK PANELS & SUB- DISTRIBUTION BOARDS 1.0 MAIN L.T. PANEL (NORMAL SUPPLY) (SS2/MLTP-1) Page 7 of 21

Description Qty. Unit NON- Amount as per Amount as per NON -2013 / Supply, installation, testing & commissioning of Main L.T. Panel extensible type suitable for 415 volts (nominal) 3 phase 4 wire, 50 Hz, A.C. Supply totally enclosed type with free standing floor mounted dust and vermin proof compartmentalised indoor type fabricated from 2mm thick CRCA sheet steel complete with busbars, ammeter, ammeter selector switch, voltmeter, voltmeter selector switch, indicating lamps, protection relays, CT's, protection mcb's, interconnections with suitable size of copper leads/solid aluminium strips/rod having following incoming and outgoing Air Circuit Breakers, MCCB's as per the drawing and technical specifications complete as required. (TOTAL OF A TO E) 1 Set 2,586,000.00 2,586,000.00 () A) INCOMER BREAKERS 2 No. 2500Amp FP Manually operated horizontal drawout type (MDO) Air Circuit Breaker (50KA) with microprocessor release, O/L, S/C & E/F protection with communication port RS485 port (Transformer Incomer). B) BUSCOUPLER BREAKERS 1 No. 2500Amp FP Manually operated horizontal drawout type (MDO) Air Circuit Breaker (50KA) as buscoupler with interlocking arrangement with incomers. 1 Set of indicating lamps for ON & OFF of buscoupler. C) BUSBARS 3000 Amp TPN busbars of aluminium alloy (Bus-Section I & II). D) OUTGOING BREAKERS WITH INSTRUMENTS i) 8 Nos. 1250 Amp Three Pole Manually operated horizontal drawout type (MDO) Air Circuit Breaker (50KA) complete with thermal magnetic release, O/L, S/C & E/F protection & neutral link. ii) 2 Nos. 800 Amp Three Pole Manually operated horizontal drawout type (MDO) Air Circuit Breaker with thermal magnetic release, O/L, S/C & E/F protection & neutral link. Page 8 of 21

Description Qty. Unit NON- Amount as per Amount as per NON -2013 / iii) 2 Nos. 400 Amp Three Pole Moulded Case Circuit Breaker (50KA) complete with microprocessor release, O/L, S/C & E/F protection & neutral link. E) INSTRUMENTS ON INCOMER BREAKERS 2 Nos. 0 to 500 Volt digital voltmeter with selector switch (96mm square) (one for each incoming breaker). 2 Nos. 0 to 2500 Amp digital ammeter (96mm square) with CT's (one for each incoming breaker) and selector switch. 2 Sets of phase indicating lights (RYB) with protection mcb's (one set for each incoming breaker). 2 Sets breaker 'ON' & 'OFF' indicating lamp (one set for each incoming breaker). 2 Sets trip circuit healthy indicating lamp (one set for each incoming breaker). 2 Sets auto trip indicating lamp (one set for each incoming breaker). 2 No. of Dual ratio CT's of 2500/500/5/5Amp ratio for APFC Relay (one for each incomer breaker). 2 Nos. trip circuit supervision relay (one for each incoming breaker). 2 Nos. electronic type Digital energy analyser having 30 day memory and parameters of KW, KWH, power factor, frequency etc. (one for each incoming breaker). 2 Nos. master trip relay (one for each incoming breaker). 2 Set of O/V & U/V relay (one for each incoming breaker). 2 Nos. Phase squence relay (one for each incoming breaker). 2.0 CAPACITOR BANK PANEL (SS-2) Page 9 of 21

Description Qty. Unit NON- Amount as per Amount as per NON -2013 / Supply, installation, testing & commissioning of Capacitor Panel suitable for 415 volts (nominal) 3 phase 4 wire, 50 Hz, A.C. Supply totally enclosed type with free standing floor mounted dust and vermin proof indoor type fabricated from 2mm thick CRCA sheet steel complete with busbars, ammeter, ammeter selector switch, voltmeter, voltmeter selector switch, indicating lamps, protection relays, CT's protection fuses, interconnections with suitable size of copper leads/solid aluminium strips/rod, auto / manual selector switch for operation of capacitor units, push buttons for manual operation, capacitor duty contractors, capacitor bank, APFC relay, power factor meter etc. complete and having following incoming and outgoing Circuit Breakers etc. as per the drawing and specifications complete as required. 2.1 Capacitor Bank Panel (400 KVAR) 2 Set 518,000.00 1,036,000.00 () A) INCOMER 1 No. 1250 Amp FP Moulded Case Circuit Breaker (50KA Ics Value) with microprocessor release for O/L, S/C & E/F protection. 1 No. 0-1250A. Ammeter with selector switch & CT's. 1 No. 0-500A. Voltmeter with selector switch 1 Set of phase indicating lamps B) BUSBARS 1500A TPN Aluminium busbars C) OUTGOING 14 stepped Automatic Power Factor Correction relay (APFC relay). 4 Nos. 100 Amp TP Moulded Case Circuit Breaker (25KA Ics Value) with thermal magnetic release and neutral link. 6 Nos. 63 Amp TP Moulded Case Circuit Breaker (25KA Ics Value) with thermal magnetic release and neutral link. 4 Nos. 40 Amp TP Moulded Case Circuit Breaker (25KA Ics Value) with thermal magnetic release and neutral link. 14 Nos. Capacitor duty contactor (one for each 50KVAR / 25KVAR/12.5KVAR) Capacitor unit. Page 10 of 21