Technical Application Guide for UP-SHINE LED wall lamp UP-WL6B-12W
Introduction Visually, WL6B led wall light impresses with its unique design as well as the tactile appeal. Smiley-face design on the wall makes everyone feel warm and cozy. Automatic water drainage system is equipped on the bottom of the lamp, which makes the lamp IP54 waterproof. The lamp heat sink adopts die-casting aluminum ADC12 with very good heat dissipation, spray powder surface treatment makes the lamp ageing-resistant and corrosion resistant. Lamp cover adopts UL94-V fire rated milky PC reflective with even and soft light output. The build-in terminal block makes installation and maintenance more convenient. The lamp adopts high quality and stable LED with long lifespan, no heat radiation and no harm to eyes and skin. It is a green and environmentally friendly lighting product. Up to 7% energy saving compared to halogen lamp Long lifetime of 5, hours 6 beam angle CCT: 3K 4K 5K 57K No UV/IR light Environment friendly, without Mercury or any other hazardous substances Application notes IP54 for indoor and outdoor use Professional electrician for installation only Switch off before installation Do not touch when in use Keep away from hot steam and corrosive gas Application Areas It is designed for indoor and outdoor lighting applications hotel, park, and corridors etc. Certificates
Product Information 66.5 Technical Specifications 158 7 Model Voltage Power Power Factor Lumen (±5%) Beam angle CCT Lifespan CRI Dimmable Dimension UP-WL6B-12W AC1-277V 12W.9 11 6 o 3K 5h 8 No 158*7*66.5mm UP-WL6B-12W AC1-277V 12W.9 14 6 o 4K 5h 8 No 158*7*66.5mm UP-WL6B-12W AC1-277V 12W.9 111 6 o 5K 5h 8 No 158*7*66.5mm UP-WL6B-12W AC1-277V 12W.9 16 6 o 57K 5h 8 No 158*7*66.5mm Driver data Sheet Driver data Non-dim Input rated Voltage Frequency Input Voltage AC1-277V 5/6Hz AC9-35V Efficiency 9% Total load Wattage 12W±1W Power Factor.9 Rated input current Full load output Voltage Rated output current Output current range 5A DC6-75V 15mA 15mA±5% Power tolerance ±5% Current output tolerance ±5% Short circuit protection Over voltage protection Over temperature protection PASS PASS PASS Withstand voltage Fixture Compatibility Rated Wattage Electrical Classification Ingress Protection Operating Temp Operating Humidity Storage Temp 12W Ⅰ IP54-2 o C~45 o C ~9% -2 o C~65 o C
Spectral Distribution 3K 4K Max=6866 [1.=2] 3.7 SDCM F3K Max=7672 [1.=2] 4.63 SDCM F4K x=351 y=48 x=72 y=734 38 5 6 7 8 38 5 6 7 8 5K 57K Max=884 [1.=2] 5.12 SDCM F5K Max=9221 [1.=2] 5.36 SDCM F57K x=421 y=645 x=354 y=512 38 5 6 7 8 38 5 6 7 8 Photometric Diagram 3K 4K Flux out: 721.5 lm Flux out: 8 lm 12 9 9. 8.1 7.2 MH=1m C/18 C9/27 12 9 15. 13.5 12. MH=1m C/18 C9/27 18 6.3 3 1 36 5.4 4.5 6 9. 7.5 54 3.6 9 6. 72 2.7 12 4.5-3 9 3 1.8.9-3 15 3 3. 1.5 AVERAGE BEAM ANGLE(5%): 68.8 DEG -25-2 -15-1 -5 5 1 15 2 25 Height Eavg, Emax Angle: 68.32deg Diameter AVERAGE BEAM ANGLE(5%): 68.4 DEG -25-2 -15-1 -5 5 1 15 2 25 Height Eavg, Emax Angle: 67.6deg Diameter 5K 57K Flux out: 7 lm Flux out: 73 lm 12 9 9.5 8.55 7.6 MH=1m C/18 C9/27 12 9 9.5 8.55 7.6 MH=1m C/18 C9/27 2 6.65 19 6.65 4 5.7 4.75 38 5.7 4.75 6 3.8 57 3.8 8 2.85 76 2.85-3 1 3 1.9.95-3 95 3 1.9.95 AVERAGE BEAM ANGLE(5%): 67.1 DEG -25-2 -15-1 -5 5 1 15 2 25 Height Eavg, Emax Angle: 68.33deg Diameter AVERAGE BEAM ANGLE(5%): 67.4 DEG -25-2 -15-1 -5 5 1 15 2 25 Height Eavg, Emax Angle: 66.37deg Diameter
Polar Diagram Comparison -15 O 18 O 15 O O 12 O O 19 9 O -6 O -3 O 38 57 76 95 O 6 O 3 O AVERAGE BEAM ANGLE (5%): 67.4 DEG C/18, 68. deg C3/21, 68.1 deg C6/24, 67.2 deg C9/27, 66.3 deg Driver lifetime & LED light decay rate Driver Lifetime LED Light Decay Rate 9 11% 4 Lifetime (hours) 8 7 6 5 4 3 2 1 65 o C 75 o C 85 o C 95 o C 15 o C Capacitor Tc ( o C) % Luminous Flux 15% 1% 95% 9% 85% 8% 75% FLUX 1 5 U'V' 7% 1 2 3 4 5 6 7 8 9 1 LifeTime (hours) 35 3 25 2 15 Temperature The testing is operated at 25 C The lifetime of capacitor, minimum of 5, hours if operated at 15 C, will be doubled whenever the temperature drops 1 C. The highest withstand temperature of IC, MOS could be 12 C The highest withstand temperature of LED junction temperature is 15 C Temperature ( o C) 9 8 7 6 5 4 3 2 1 11:35:42 11:53:29 12:11:29 12:29:29 12:47:29 13:5:29 13:23:29 13:41:29 13:59:29 14:17:29 14:35:29 14:53:29 15:11:29 15:29:29 15:47:29 16:5:29 16:23:29 16:41:29 16:59:29 17:17:29 Time IC Capactior MOS PCB LED Fitting Environmental temperature The driver lifespan is based on capacitor working temperature.
Installation Step1 Step2 Step3 Take out wall light and accessory pack from package. Fix the plastic anchor into wall. Loose screws and take out the bracket from lamp body. Step4 Fix the bracket on the wall with screws Step5 Open junction box, connect "L","N", G wires to terminal block respectively and lock the driver box, then fix the light on the wall. Step6 Switch on after complete installation. OFF ON L = BROWN N = BLUE = YELLOW-GREEN Packaging Information SIZE(CM) N.W/pc (KGS) G.W.(KGS) Q'TY(PCS) Carton 54.5*46*25.5 95 13 36 CTNS Q'TY(PCS) VOLUME(CBM) 2'' standard container 43 1548 28 4'' standard container 86 396 56 Phone: +86 755 2919 7332 Add: 2nd building Dingfeng High-Tech Zone, Fuyuan 1st road, Fu Yong Sub-district, Bao'an, Shenzhen China