Series 70 Custom Potentiometer Designer Guide

Series 70 Custom Potentiometer Designer Guide.05 [0.8mm] /8 [.8mm].50 [6.5mm].055 [.7mm] 6 ROUTE 0, STE 6 EST HNOVER NEW JERSEY 0796 Phone Internet

POT PROTOTYPES PRONTO! Dual Potentiometer, Dual Rotary Switch, Single Flatted /8, Solder Lugs Single Potentiometer, Single Rotary Switch, Single Slotted /, Solder Lugs Single Potentiometer, Single /, Solder Lugs Dual Potentiometer, Dual, Solder Lugs Dual Potentiometer, Single /, PC Pins Single Potentiometer, Single Slotted /, PC Pins Triple Potentiometer, Single /8, PC Pins Quad Potentiometer, Single /, Solder Lugs Now almost any special combination potentiometer you specify can be manufactured and shipped soon after your order is received. Since Clarosystem and Mod Pot potentiometers are modular in construction, we can produce prototype quantities of / or 5/8 inch square, conductive plastic, cermet, or hot molded carbon pots for you in just a few hours.... and even production quantities in a matter of days with our VIP (Very Important Potentiometer) service! Over one billion combinations of single, dual, triple, quad arrangements, push-pull or rotary switches and hundreds of shaft terminal variations can be produced. If you need a potentiometer and you need it fast, call our product manager or fax us your requirements using the Custom Potentiometer Order Forms included in this catalog. WHY WIT? 6 Route 0, STE 6 East Hanover, NJ 0796-06 Phone 97-887-550 Toll Free -800-6-808 FX 97-887-90

Series 70, 7 Hot-Molded Carbon*, Conductive Plastic (CP), and Cermet Panel Potentiometers UNMTCHED FLEXIILITY The MOD POT Family includes: Series 70 Metal or Plastic Metal ushing. Series 7 Metal or Plastic Plastic ushing. FETURES Modular Construction Multiple Sections/Concentric s Rotary and Push-Pull Switch Options ttenuators Linear and Non-Linear Tapers 50 Ohms to 0 Megohms 0.65 Inch (5,87 mm) Square /" or /8" Diameter Metal or Plastic RoHS Compliant ENEFITS n Versatility n Versatility n Versatility n Versatility n Versatility n Wide Resistance Range n Moderate Size n Versatility n Non-Magnetic n International cceptance * Hot Molded Carbon is no longer available Page THE POTENTI SPECILISTS

SPECIFICTIONS General Versatile Panel Potentiometer The MOD POT concept consists of standardized potentiometer modules that can be mixed and matched in over a billion combinations. Now, you can be far more imaginative with potentiometers because you can get special combinations with the ease of standards. llen-radley originated the modular potentiometer concept in response to requests from design engineers who wanted virtually unlimited variety in variable resistors for greatly increased design freedom MOD POT modules are 5/8 inch square by about / inch deep. This provides minimum center-to-center distance for compact panel mounting. You can gang resistance and switch modules in combinations of up to four modules. Select from a whole family of resistive elements, resistive values and tolerances, tapers, shafts, bushings, lug options and more. You get a virtually unlimited number of design options. TEMPERTURE RNGE Maximum Minimum Series Module Type Temp C Temp C Hot-Molded* or 70 Conductive +0 55 Plastic Cermet +50 55 Hot-Molded*, 7 Conductive +00 55 Plastic or Cermet 70, 7 Vernier +00 55 70, 7 Switches +00 55 Hardware Hardware is:.50 inch (6,5 mm) diameter bushing: () M-78; () M-7; () M-76 (M-76 is supplied only with locking bushings).75 inch (9.5 mm) diameter bushing: () M-898; () M-786; () M-68 (M- 68 is supplied only with locking bushings) ll hardware shipped in bulk not assembled unless otherwise specified. Mounting Torque (Series 7) Torque applied to the mounting nuts should not exceed 7 inch-pounds (790 mn-m) for the.50 inch (6,5mm) diameter bushing or inch-pounds (580 mn-m) for the.75 inch (9,5 mm) diameter bushing. * Hot Molded Carbon is no longer available Turning Torque Initially, at 5ºC, the potentiometer torque will be 0.5 inch-ounce (.5 mn-m) minimum while the maximum is: TORQUE INCH-OUNCES (mn-m) Cermet and Style Hot-Molded Elements CP Elements Single ().5 () Dual 6 ().5 (8) Triple 8 (56).5 (5) Quad 0 (7).5 () Variation within a control is oz. in. maximum. The maximum additional torque required for the vernier drive is 0 inch-ounces (7mN-m) on inner, coarse adjustment shaft. Stop Torque Minimum of inch-pounds (5 mn-m) except for the Series 7 with a.5 inch (.8 mm) diameter shaft which is inch-pounds (5 mn-m) minimum. Vernier drives have slip clutches. Rotation Rotation in Degrees Total Electrical Single Mechanical ±5 (Nominal) Potentiometers 00 60 Potentiometers and 00 60 Rotary Switch Potentiometers and 05 60 Push-Pull Switches Rotary Switches 5 Rotary Switches and 0 Push-Pull Switches Vernier drive Two vernier drive modules are available with hot-molded*, cermet, and conductive plastic modules. Through a gearing arrangement, the total rotation will be changed to 6 turns or turns. ratchet clutch is provided in place of fixed stops for the fine adjustment shaft. Series 70 variable resistors may have concentric shafts. The inner concentric shaft (.078 inch (.98 mm) diameter) may be used as a coarse adjustment shaft. Enclosure Dust and splash resistant. They are not immersion sealed. Materials Corrosion-resistant and essentially nonmagnetic. The shafts and bushings of the Series 7 are plastic. Standard Marking State Electronics part number and nominal total resistance are marked in two lines. Other markings are possible. Page THE POTENTI SPECILISTS

Electrical Total resistance tolerances Hot-Molded*, CP: ±0% or ±0%; Cermet: ±5% or ±0%. POWER Power in Watts per Section Hot- Molded* Cermet CP Series at 70 C at 70 C at 70 C 70 (single).0.0.5 70 (multi-section).5.0.5 7 (single).5.0.5 7 (dual).5.5.5 Power derating Derate power linearly from rated temperature to zero at maximum temperature. Derate power 50 percent for non-metallic mounting. Derate 60 percent for CP elements wit and tapers. Derate 50 percent for hot-molded elements with,, S, and D tapers. For rheostat applications, derate power directly with shaft or actuator position. Voltage 50 volts maximum working voltage (RMS or DC), or as determined by Emax. = PR, whichever is less (at sea level). TTENUTORS HOT MOLDED* Series ridged-t L ridged-h Straight-T 70 7 N N Consult factory for further details =vailable N=Not vailable Linearity ±5 percent independent for linear tapers with a total resistance up to.0 megohm. Dielectric withstanding voltage Maximum continuous voltage, 50 volts (RMS) at sea level. Will withstand a one second test of 000 volts (RMS) at sea level or 500 volts (RMS) at. inches (86.6) mercury. Insulation resistance 000 megohms minimum for clean and dry conditions at +5 ºC. Operational Contact resistance variation linear taper Maximum value is: Hot-Molded* & Cermet:.5 percent of nominal resistance value or.5 ohms, whichever is greater. CP:.0 percent of nominal resistance value. Load Life Maximum change in total resistance as a result of a 000 hour test at rated power across entire element at +70º C (.5 hours ON, 0.5 hour OFF ) 5 percent for cermet element, 0 percent for hot-molded* and CP elements Rotational life 0 percent maximum change in total resistance as a result of a 00,000 mechanical cycle life test without load. Environmental Vibration percent maximum change in total resistance, 5 percent maximum change in resistance setting. (Tested per method 0, condition C of MIL-STD-0.) Shock percent maximum change in total resistance, 5 percent maximum change in resistance setting. (Tested per method, condition I of MIL-STD-0.) Humidity Maximum change in total resistance as a result of 95 percent humidity at 0ºC for 00 hours: 5 percent for cermet element, 0 percent for hot-molded and CP elements. Temperature cycling percent maximum change in total resistance as a result of the temperature cycling test. (Five cycles at 55º C to the maximum temperature.) Effect of soldering Maximum change in total resistance as a result of immersing the terminals in 50º C solder to within 0.5 inch (,8mm) of the resistor body for 5 seconds: percent for cermet element, percent for hot-molded and CP elements. Low temperature operation Maximum change in total resistance as a result of the low teperature operation test ( 55ºC for two hours without load and 5 minutes with rated load): percent for cermet element; percent for hot-molded and CP elements. High temperature exposure Maximum change in total resistance as a result of the high temperature exposure test (maximum rated temperature for 000 hours without load): percent for cermet element; 0 percent for hot-molded and CP elements. Washability MOD POT performance may be adversely affected if subjected to conventional after-solder boardwash processes. * Hot Molded Carbon is no longer available Page 5 THE POTENTI SPECILISTS

Environmental (continued) Temperature characteristics Maximum percent temporary total resistance change from the +5 C value. See chart below. Temperature coefficient For cermet linear taper elements, temperature coefficient less than ±00 ppm/ C. Nominal CP U Linear Taper. C Resistance in Ohms 55 5 0 +5 +55 +85 +00 +0 00 9.0 6.0.0 0 +.5 +6.5 +8.0 +0 K ±5.5 ±.0 ±.5 0 ±.5 ±.0 ±.0 ±5.0 0K +5.0 +.0 ±.5 0 ±.0 ±.0 ±.5 ±.0 00K +5.0 +.0 ±.5 0 ±.0 ±.0 ±.5 ±.0.0 Meg +6.0 +.0 ±.0 0 ±.5 ±.0 ±.0 ±5.0 Nominal HOT MOLDED* U Linear Taper. C Resistance in Ohms 55 5 0 +5 +55 +85 +00 +0 00 +.5 +.5 +.5 0 ±.0 ±.5 +.0 +.5 K +5.5 +.0 +.5 0 ±.5 ±.0 +.5 +.5 0K +7.0 +.5 +.0 0 ±.0 ±.5 +.0 +5.5 00K +8.0 +.0 +.0 0 ±.5 ±.0 +.5 +6.0.0 Meg +0.0 +5.0 +.5 0 ±.5 ±.5 ±5.0 +7.5 For S, and D tapers multiply percentage figures shown above by.5 * HOT MOLDED option is discontinued - for reference only Tapers % RESISTNCE 00 90 80 70 60 50 0 0 0 0 0 UNIT TPER TOTL RESISTNCE RNGE U 0 0 0 0 0 50 60 70 80 90 00 % ELECTRICL ROTTION (CLOCKWISE) 50 Ohms to 0.0 Megohms,, S, D 50 Ohms to 0.0 Megohms Cermet U, W (X=5%) 00 Ohms to 5.0 Megohms CP U 00 Ohms to.0 Megohm S U W X, 50 Ohms to.0 Megohm D Tapers, D, S, U, W and X are measured between the wiper and the counter-clockwise terminals (pin and ). Taper is measured between the wiper and the clockwise terminals (pin and ). Tapers vailable in the following resistance ranges: Hot- Molded* Schematic End Resistance TPER n n n n Potentiometer Terminals Hot- Molded* Minimum Resistance etween Terminals: CP Cermet & & & & & & U n n n n n n S n n n n n n n n n n D n n Less than 0.00 percent of total resistance or less than ohms, whichever is greater. Less than percent of total resistance or less than ohms, whichever is greater. Less than ohms Less than ohms # # # * Hot Molded Carbon is no longer available Page 6 THE POTENTI SPECILISTS

Switches Rotary Switch Maximum percent temporary total resistance change from the +5 C value. See chart below. Rotary Switch The rotary switch consists of two sets of contacts. See Part Number Explanation for available options. When supplied on the Series 7, the rotary switch must be used with a.50 inch (6,5 mm) diameter shaft. Push-pull Switch four pole switch that is operated by a.5 inch (,8mm) diameter solid shaft. n inner concentric shaft that operated the push-pull switch only may have a diameter of.5 inch (,8mm) or.078 inch (,98mm). lengths are measured from the bushing mounting surface to the free end of the shaft with the shaft in the extended position. vailable only on Series 70. Momentary Push Switch push-pull switch equipped with a return spring such that the switch will return to the extended postion when the actuating force is removed. vailable only on Series 70. mbient Temperature 55º C to +00ºC Life The switches will be electrically and mechanically operative after operational life test at rated current and voltage with a resistive load, per switch characteristics below. Terminals Switches are available with lug terminals only. They are not available with square terminals. On request, switches will be rotated 90º such that the switch terminals come out the sides of the control instead of the top and bottom. ND MOMENTRY ES Voltage in Volts Current Switch at 60 Hz in ctuating Operational Number Type RMS mps Force Travel Life 00 Push-Pull 5 7 ounces (.9N) Min..5 Inch 5,000 9 ounces (5.N) Max. (.8mm) 00 Momentary 5 0 ounces (5.6N) Min..5 Inch 5,000 Push 0 ounces (8.N) Max. (.8mm) ROTRY ES Med ctuating Torque = Maximum of 0 inch-ounces (5.6 N) Low ctuation Torque = Maximum of 7.5 inch-ounces (5 mn-m). Minimum of.5 inch-ounces (.7 mn-m) n For use with conductive plastic element modules only. (Discontinued- For Reference Only) Length of Throw In Detent Voltage in Volts Current Operates Operates Switch Detent Terminals Term at 60 HZ in ctuating Switch and Switch Operational Number at and are: and are: RMS mps Torque Pot Only Life 00 C end Open Closed 5 Med 5 5 5,000 00 C end Open Open 5 Med 5 5 5,000 00 end Open Closed 5 Med 5 5 5,000 00 end Open Open 5 Med 5 5 5,000 T n end Open Closed 5. Med 5 5 5,000.0 n C end Open Open 5. Low 5 5 5,000.0 T n C end Open Open 5. Low 5 5 5,000.0 n CC end Open Open 5. Low 5 5 5,000.0 # # # # Switch Number T, 00, T or 00 Shown in Detent Rotary Switches * Hot Molded Carbon is no longer available Page 7 THE POTENTI SPECILISTS # # # # Switch Number, 00, or 00 Shown in Detent Push-Pull or Momentary Push Switch # # #5 #7 Switch Number 00 or 00 With Extended # # #6 #8

Explanation of Part Numbers MOD POT SERIES 70,7 Conductive Plastic (CP), Cermet, and Hot-Molded Carbon* Panel Potentiometers Locating Lug Options 6 7 8 C 9 D 5 Code* Letter Plastic Code Letter Type and ushing Diameter Inch Diameter Type mm Ending n ushing Diameter Inch mm G S.50 (6.5) Standard Slot.75 (9.5) P.50 (6.5) Plain Round.75 (9.5) F.50 (6.5) Standard Flat.75 (9.5) L.5 (.8) Standard Slot.50 (6.5) R.5 (.8) Plain Round.50 (6.5) K.5 (.8) Standard Flat.50 (6.5) X.50 (6.5) Cross Slot *These codes used with Series 70 only Total Resistance Value First two digits are significant figures and the third indicates the number of zeros following the first two digits Examples: 500 = 50 Ohms 50 = 500 Ohms 55 =.5 Megohms asic Type MOD POT Series 70 Series 7 Configuration Lug Terminals Single (Hot Molded) Single (Cermet) J Single (Conductive Plastic) C Dual (Hot Molded) n D Dual (Cermet) n T Dual (Conductive Plastic) n E Triple (Hot Molded) n F Triple (Cermet) n G Quad (Hot Molded) n H Quad (Cermet) n K Single (Hot Molded) with Switch 00 L Single (Cermet) with Switch 00 Square Terminals M Single (Hot Molded) N Single (Cermet) U Single (Conductive Plastic) P Dual (Hot Molded) n R Dual (Cermet) n W Dual (Conductive Plastic) n n if the electrical specifications are not identical for each section, a special number will be assigned. 70G056L50U ushing Type and Length F Face Plate H Plain inch G Plain.50 inch (,70 mm) long (6,5 mm) long M Locking.75 inch N Plain.75 long (9,5 mm) long (9,5 mm) long L Locking inch (,70 mm) long Lengthn Measured from mounting surface of the potentiometer in inches and sixty-fourths Use a three digit code. Examples: 7/8" shaft length -/" shaft length. 056 6 inches sixty-fourths one inch 6/6 or / inch 0 56/6 (7/8") Some Common Lengths Inches Three Digit Fraction Decimal Part Number Code /.50 06 /8.75 0 7/6.7 08 / 0 5/8.65 00 /.750 08 7/8.875 056.000 00 -/8.5 08 -/.50 6 -/.000 00 Taper Type and Total Resistance Tolerance CERMET W Linear (U), ±0% X Linear (U), ±5% HOT-MOLDED* or CONDUCTIVE PLSTIC U Linear (U), ±0% M Linear (U), ±5% Clockwise Modified Logarithmic (), ±0% R Clockwise Modified Logarithmic (), ±0% Counterclockwise Modified Logarithmic (), ±0% T Counterclockwise Modified Logarithmic (), ±0% HOT-MOLDED* D Clockwise Exact Logarithmic (D), ±0% K Clockwise Exact Logarithmic (D), ±0% S Modified Linear (S), ±0% Y Modified Linear (S), ±0% C Linear (U), ±0% with 50% (center) Tap F Linear (U), ±0% with 50% (center) Tap ttenuator Type and Characteristic Impedance Tolerance HOT-MOLDED* E ttenuator L-Pad ±5% L ttenuator L-Pad ±0% N ttenuator ridged T-Pad ±5% L ttenuator ridged T-Pad ±0% n CONCENTRIC ND SPECIL SHFTS REQUIRE SPECIL PRT NUMER ISSUED Y THE FCTORY. * Hot Molded Carbon is no longer available CUTION: Not all part number combinations are valid. Check parameter limits in text. EXMPLE: 70N0P50U Invalid ushing/ Combination Plain.75 inch (9,5 mm) long bushing with plain.75 inch (9,5 mm) long shaft. Page 8 THE POTENTI SPECILISTS

Common Combinations The MOD POT Potentiometer is available in single, dual, triple, and quadruple construction. This includes potentiometer, switch and vernier drive modules. The table below lists some of the options available for single SERIES 70,7 and multi-section controls. ecause of the versatility of the MOD POT Potentiometer, many other options are available. Momentary push switches may be used in place of push-pull switches in the listed combinations. Single Unit Dual Unit Single Dual Unit Concentric Triple Unit Single Triple Unit Concentric Quad Unit Single Quad Unit Concentric Single Unit Dual Unit Triple Unit Quad Unit Potentiometer Potentiometer Potentiometer Potentiometer / Solder Lugs / PC Pins / Solder Lugs / PC Pins Notes Section # Section # Section # Section # Dwg# Page Dwg# Page Dwg# Page Dwg# Page Potentiometer -PC Rotary Switch Push-Pull Switch 5 Potentiometer Potentiometer 5 -PC 5 Potentiometer Rotary Switch 5 6 5-PC 7 5-90 6 5-PC-90 7 Potentiometer Push-Pull Switch 5 8 5-PC 9 5-90 8 5-PC-90 9 5 Vernier Drive Potentiometer 6 0 6-PC 0 Potentiometer Potentiometer 7 7-PC 5 Potentiometer Push-Pull Switch 8 8-PC 8-90 8-PC-90 6 Potentiometer Rotary Switch 9 9-PC 5 9-90 9-PC-90 5 5 Vernier Drive Potentiometer 0 6 0-PC 6, 5 Rotary Switch Push-Pull Switch 6 5 Potentiometer Potentiometer Potentiometer 7 -PC 7 5 Potentiometer Potentiometer Push-Pull Switch 8 -PC 9-90 8 -PC-90 9 5 Potentiometer Rotary Switch Push-Pull Switch C 0 C-PC C-90 0 C-PC-90 5 Potentiometer Potentiometer Rotary Switch -PC -90 -PC-90 5 Potentiometer Rotary Switch Rotary Switch -PC 5-90 -PC-90 5 5 Vernier Drive Potentiometer Potentiometer 6 -PC 7 5 Potentiometer Potentiometer Potentiometer 5 7 5-PC 7 5 Potentiometer Potentiometer Rotary Switch 6 8 6-PC 9 6-90 8 6-PC-90 9 5 Potentiometer Potentiometer Push-Pull Switch 7 0 7-PC 7-90 0 7-PC-90 5 Potentiometer Rotary Switch Push-Pull Switch 8 8-PC 8-90 8-PC-90 5 Vernier Drive Potentiometer Potentiometer 9 9-PC,,5 Vernier Drive Potentiometer Rotary Switch 0 5 0-PC 6 0-90 5 0-PC-90 6,5 Potentiometer Potentiometer Potentiometer Potentiometer 7 -PC 7 5 Potentiometer Potentiometer Potentiometer Push-Pull Switch 8 -PC 9-90 8 -PC-90 9 5 Potentiometer Potentiometer Rotary Switch Push-Pull Switch C 50 C-PC 5 C-90 50 C-PC-90 5 5 Potentiometer Potentiometer Potentiometer Rotary Switch D 5 -PC 5-90 5 -PC-90 5 5 Vernier Drive Potentiometer Potentiometer Potentiometer 5 5 5-PC 5 5 Potentiometer Potentiometer Potentiometer Potentiometer 6 55 6-PC 55 5 Potentiometer Potentiometer Potentiometer Rotary Switch 7 56 7-PC 57 7-90 56 7-PC-90 57 5 Potentiometer Rotary Switch Potentiometer Push-Pull Switch 8 58 8-PC 59 8-90 58 8-PC-90 59,5 Potentiometer Potentiometer Rotary Switch Rotary Switch 9 60 9-PC 6 9-90 60 9-PC-90 6 5 Potentiometer Potentiometer Rotary Switch Push-Pull Switch 0 6 0-PC 6 0-90 6 0-PC-90 6 5 Potentiometer Potentiometer Potentiometer Push-Pull Switch 6 -PC 65-90 6 -PC-90 65 5 Vernier Drive Potentiometer Potentiometer Potentiometer 66 -PC 66,,5 Vernier Drive Potentiometer Potentiometer Rotary Switch 67 -PC 68-90 67 -PC-90 68,,5 NOTES:. The outer shaft operates Sections # and #.. The outer shaft operates Sections #, #, and #.. The inner shaft (.078 [.98 mm] diameter) is for the coarse adjustment, the outer shaft for the fine adjustment.. Series 7 must have.50 inch (6.5 mm) diameter shaft. 5. vailable in 70 Series only. Hot Molded Carbon is no longer available Page 9 THE POTENTI SPECILISTS Switch Module Rotated 90

Components RESISTNCE MODULES LINER TPER Element Type Hot-Molded Cermet Conductive Carbon* Plastic Resistance Tolerance 0% or 0% 0% 0% Taper (U) or (M) (W) (U) Terminal Type Lug Pin Lug Pin Lug Pin Resistance (ohms) Code 00 0,000 0 0,000 0 00,000 0,000,000 05 0,000,000 06 * * * * 00 0,000 0 0,000 0 00,000 0 50 5,500 5 5,000 5 50,000 5,500,000 55 * * 50 500 * * * * 500 50 5,000 50 50,000 50 500,000 50 5,000,000 505 * * = vailable from Distributor Stock. = Special order only. Contact factory for information. * = Not vailable. SERIES 70,7 Page 0 THE POTENTI SPECILISTS RESISTNCE MODULES NON-LINER TPER Element Type Hot-Molded Conductive Hot-Molded Conductive Carbon* Plastic Carbon* Plastic Resistance Tolerance 0% 0% 0% 0% Taper () () () () Terminal Type Lug Pin Lug Pin Lug Pin Lug Pin Resistance (ohms) Code 00 0 * * * * * * * *,000 0 0,000 0 00,000 0,000,000 05 00 0 * * * * * * * *,000 0 0,000 0 00,000 0 50 5,500 5 5,000 5 50,000 5,500,000 55 * * * * 500 50 5,000 50 50,000 50 500,000 50 5,000,000 505 * * * * = vailable from Distributor Stock. = Typically a Stock Item. Contact State Electronics for information. * = Not vailable. * Hot Molded Carbon is no longer available

Standard Components SERIES 70,7 STNDRD SHFTS Ending FMS Type Used With Length Plain Slotted.75 (9,5 mm) 70 70.75 (9.5 mm) Dia. (,70 mm) 70 Metal ushing.65 (5,88 mm) 70.50 (6,5 mm) Dia. Solid Series 70.750 (9,05 mm) 70.75 (9,5 mm) 70 70 (,70 mm) 70 Metal.50 (6.5 mm) Dia..65 (5,88 mm) 70.5 (,8 mm) Dia. Solid ushing.750 (9,05 mm) 70 Series 70.875 (, mm) 70 (6,50 mm) 70.75 (9,5 mm) Plastic.75 (9.5 mm) Dia. (,70 mm).50 (6,5 mm) Dia. Solid ushing.65 (5,88 mm) Series 70; 7.750 (9,05 mm).875 (, mm).75 (9,5 mm) Plastic.50 (6.5 mm) Dia. (,70 mm).5 (,8 mm) Dia. Solid ushing.65 (5,88 mm) Series 70; 7.750 (9,05 mm).875 (, mm) Metal.75 (9.5 mm) Dia..65 (5,88 mm) Outer ushing.750 (9,05 mm) Concentric Series 70 Metal.50 (6.5 mm) Dia. Outer ushing.65 (5,88 mm) Concentric Series 70 Metal.50 (6.5 mm) Dia. Inner ushing Concentric or.5 (8,58 mm) Standard for Dual Deck.75 (9,5 mm) Dia. Constructions only ushing Series 70 = vailable on Series 70, 7 = vailable on Series 70 70 = vailable on Series 70 only = vailable as a Special Order only. Consult factory for information. STNDRD SHFTS Switch Part Number 00 00 00 00 00 00 Type Rotary Rotary Rotary Rotary Push Momentary Pull Push STNDRD USHINGS Length Series Diameter Type Inches Millimeters 70 7 ushingless See Note n N Plain.50 6.5.50 Inch.75 9.5 N (6.5 mm) Locking.75 9.5 N.70 N Plain.50 6.5 N.75 Inch.75 9.5 (9.5 mm).70 N Locking.75 9.5 N.70 N Mounting bushings are supplied with -NEF- thread. ll bushing lengths measured from the mounting face to the end of the bushing. = vailable. N = Not vailable. STNDRD SHFT ND USHING COMINTIONS Diameter in Inches.75 (9,5 mm).50 (6,5 mm) Type Dia. ushing Dia. ushing Solid or Outer.50.5 Concentric (6.5 mm) (.8 mm) Inner.5 (.8 mm).078 Concentric Verniers.078 (.98 mm) (.98 mm) Series 7 shafts and bushings are plastic. n No mounting bushing. is cross slotted for screwdriver actuation and is flush with faceplate. See dimensions on Page 70 * Hot Molded Carbon is no longer available. Page THE POTENTI SPECILISTS

Ordering Information. asic type (Series 70, Series 7). Type of element (cermet or conductive plastic (CP)).. Type of terminals (resistor element only).. Number of sections. 5. Taper (each element on multi-section controls). 6. Total resistance value in ohms (each element on multisection controls). 7. Tolerance percent (each element on multi-section controls). 8. ushing type (plain or locking). 9. ushing length in inches or millimeters. 0. ushing diameter.75" (9.5mm) or.50" (6.5mm) SERIES 70,7. ending (plain, slotted or flatted).. length from mounting surface in inches or millimeters.. material: plastic or metal.. Switch type. 5. Vernier drive. 6. Locating lug option. 7. Mounting hardware. 8. Your part number, if any. 9. Marking requirement on the part. 0. Special features. (Forward complete detailed specifications) DIMENSIONS Mounting Holes D C E Dimension C Note: Solid line is.6 inch diameter Dashed line is.06 inch diameter DIMENSION C DIMENSION C LUG Minimum hole dia. Minimum hole dia. DIMENSION D DIMENSION E OPTION DIMENSION DIMENSION for /" dia. bushing for /8" dia. bushing Minimum hole dia Minimum hole dia..05 (7,75) *.6 (6,6).06 (0,).096 (,) *.05 (7,75).05 (7,75).6 (6,6).06 (0,).096 (,).096 (,).75 (9,5) *.6 (6,6).06 (0,).096 (,) * * *.6 (6,6).06 (0,) * * 5.75 (9,5).75 (9,5).6 (6,6).06 (0,).096 (,).096 (,) 6.7 (,0) *.6 (6,6).06 (0,).8 (,) * 7.7 (,0).7 (,0).6 (6,6).06 (0,).8 (,).8 (,) 8.5 (,9) *.6 (6,6).06 (0,).8 (,) * 9.5 (,9).5 (,9).6 (6,6).06 (0,).8 (,) * *.05 (7,75).6 (6,6).06 (0,) *.096 (,) *.75 (9,5).6 (6,6).06 (0,) *.096 (,) C *.7 (,0).6 (6,6).06 (0,) *.8 (,) D *.5 (,9).6 (6,6).06 (0,) *.8 (,) Dimension tolerance ±.06 (0,0) except as specified * = Not Required * Hot Molded Carbon is no longer available Page THE POTENTI SPECILISTS

Series 70, 7 Product Drawings The product drawings on the following pages show over 00 different configurations. Many other options are available - contact your State Electronics sales representative for information. Section : Single Module... Pg. Section : Dual Module, Single...Pg. 5 Section : Dual Module, Concentric...Pg. Section : Triple Module, Single...Pg. 7 Section 5: Triple Module, Concentric...Pg. 7 Section 6: Quad Module, Single...Pg. 7 Section 7: Quad Module, Concentric...Pg. 55 Section : Single module, Single Single Potentiometer, Single, Solder Lugs T.59±.0 (5.06±0.80 ).5 (5.6).0 Mounting Surface CP Element =.5 (8.76) Cermet =.6 (9.9) T =.75±.00 (.5±0.5) =.00±.00 (.5±0.5) = CP Element.085±.005 (.6±0.); Cermet.5Max = CP Element.05±.00 (0.8±0.05); Cermet.05±.00 (0.6±0.05) Terminal hole size:.07±.005 x.078±.005 (.9 ±0. x.98±0.).0 (5.6).65 (5.88).65 (5.88) -PC Single Potentiometer, Single, Solder Pins.0.65 (5.88) T (.90±.0).5 (5.97) T T =.00±.00 (5.08±0.5) =.05±.00 (0.6±0.05) Mounting Surface.75 (9.5) (.70).65 (5.88).085±.005 (.6±0.).68±.0 (5.70±0.80 ). Cermet Plating - Terminals & :.05" ±.00 Soft Copper CD lloy 0, Plate 50 00 Microinches right Tin, Whisker-Free (RoHS) CP Plating - Terminals & :.05" ±.00 Soft Copper CD lloy 0, Plate 50 00 Microinches right Tin, Whisker-Free (RoHS) Cermet Plating - Terminal :.05" ±.00 Soft Copper CD lloy 0, No Plate CP Plating - Terminal :.05" ±.00 Soft Copper CD lloy 0, No Plate. ll drawings are shown with /8" dia. bushing with /" dia. shaft. /" dia. bushing with /8" dia. shaft is available. Locking bushing is also available.. Refer to Page 70 for Locating Lug options.. asic dimensions are in inches. Dimensions in parentheses are in millimeters. Dimensional Tolerance ±.06 (0,0), except as specified. Page THE POTENTI SPECILISTS

Section : Single module, Single (continued) Single Rotary Switch, Single, Solder Lugs.0 (5.6).09±.00 (.78±0.5).0.05±.00 (0.8±0.05).75 (8.).65 (9.).0 (5.6).±.00 (8.7±0.5). (.57).085±.005 (.6±0.).60±.0 (5.9±0.80).66 (6.76).09±.00 (.78±0.5) ottom View.65 (5.88) Terminal hole size:.07±.005 X.078±.005 (,9 ±0, X,98±0,).65 (9.).65 (5.88) TOTL ROTTION 00 C CTUTION 5 LTERNTE CTUTION 5 Single Push-Pull/Momentary Switch, Single, Solder Lugs.0 (5.6).75 (8.).65 (9.).5 (.8).65 (5.88) T.88±.00 (.76±0.5) 5 7 6 8.0.0 (5.6).59±.00 (9.±0.5).7±.0 (8.87±0.80).87 (.75 ).8 (5.56).65 (5.88).59±.00 (9.±0.5).8 (5.56) ottom View T =.085±.005 (.6±0.) =.05±.00 (0.8±0.05) Terminal hole size:.07±.005 x.078±.005 (.9 ±0. x.98±0.) Note: length is measured in outer position.65 (9.).65 (5.88) TOTL ROTTION 00 C CTUTION 5 LTERNTE CTUTION 5. Cermet Plating - Terminals & :.05" ±.00 Soft Copper CD lloy 0, Plate 50 00 Microinches right Tin, Whisker-Free (RoHS) CP Plating - Terminals & :.05" ±.00 Soft Copper CD lloy 0, Plate 50 00 Microinches right Tin, Whisker-Free (RoHS) Cermet Plating - Terminal :.05" ±.00 Soft Copper CD lloy 0, No Plate CP Plating - Terminal :.05" ±.00 Soft Copper CD lloy 0, No Plate. ll drawings are shown with /8" dia. bushing with /" dia. shaft. /" dia. bushing with /8" dia. shaft is available. Locking bushing is also available.. Refer to Page 70 for Locating Lug options.. asic dimensions are in inches. Dimensions in parentheses are in millimeters. Dimensional Tolerance ±.06 (0,0), except as specified. Page THE POTENTI SPECILISTS

Section : Dual module, Single Dual Potentiometer, Single, Solder Lugs T T.968±.07 (.59±.9 ).5 (5.6).00±.00 (.5±0.5).00±.00 (.5±0.5).0 Mounting Surface.0 (5.6) T =.75±.00 (.5±0.5) =.00±.00 (5.08±0.5) = CP Element.085±.005 (.6±0.); Cermet.5Max = CP Element.05±.00 (0.8±0.05); Cermet.05±.00 (0.6±0.05) = CP Element.5 (8.76); Cermet.6 (9.9) Terminal hole size:.07±.005 x.078±.005 (.9 ±0. x.98±0.).65 (5.88).65 (5.88) -PC Dual Potentiometer, Single, Solder Pins.0.65 (5.88) T T T (.90±.0).5 (5.97) T T =.00±.00 (5.08±0.5) =.05±.00 (0.6±0.05).65 (5.88).75 (9.5) Mounting Surface.085±.005 (.6±0.) (.70).08±.07 (5.85±.9 ). Cermet Plating - Terminals & :.05" ±.00 Soft Copper CD lloy 0, Plate 50 00 Microinches right Tin, Whisker-Free (RoHS) CP Plating - Terminals & :.05" ±.00 Soft Copper CD lloy 0, Plate 50 00 Microinches right Tin, Whisker-Free (RoHS) Cermet Plating - Terminal :.05" ±.00 Soft Copper CD lloy 0, No Plate CP Plating - Terminal :.05" ±.00 Soft Copper CD lloy 0, No Plate. ll drawings are shown with /8" dia. bushing with /" dia. shaft. /" dia. bushing with /8" dia. shaft is available. Locking bushing is also available.. Refer to Page 70 for Locating Lug options.. asic dimensions are in inches. Dimensions in parentheses are in millimeters. Dimensional Tolerance ±.06 (0,0), except as specified. Page 5 THE POTENTI SPECILISTS

Section : Dual module, Single (continued) 5 Single Potentiometer, Single DPST Rotary Switch, Solder Lugs.0 (5.6).75 (8.).0 (5.6) ROTRY T.5 (5.6).±.00 (8.7±0.5).09±.00 (.78±0.5) ottom View. (.57).0.09 ±.00 (.78 0.5).977 ±.07 (.8 ±.9).50 ±.00 (6.5 ± 0.5).65 (5.88) T =.75 ±.00 (.5 ± 0.5) =.085±.005 (.6±0.) =.05±.00 (0.8±0.05) = CP Element.085±.005 (.6±0.); Cermet.5Max = CP Element.05±.00 (0.8±0.05); Cermet.05±.00 (0.6±0.05) Terminal hole size:.07±.005 x.078±.005 (.9 ±0. x.98±0.).65 (5.88).00±.00 (.5±0.5).00±.00 (.5±0.5) CP Element.6 (9.9) Cermet.5 (8.76) C CTUTION 5 TOTL ROTTION 00 LTERNTE CTUTION 5 5-90 Single Potentiometer, Single DPST Rotary Switch, Solder Lugs (Rotated Switch Module).0.0 (5.6) ROTRY.75 (8.) ROTRY. (.57) T.09 ±.00 (.78 0.5).977 ±.07 (.8.9).5 (5.6).75 ±.00 (.5 0.5).50 ±.00 (6.5 0.5) ottom View.65 (5.88).0 (5.6).09±.00 (.78±0.5) T =.75 ±.00 (.5 ± 0.5) T =.085±.005 (.6±0.) =.05±.00 (0.8±0.05) = CP Element.085±.005 (.6±0.); Cermet.5Max = CP Element.05±.00 (0.8±0.05); Cermet.05±.00 (0.6±0.05) Terminal hole size:.07±.005 x.078±.005 (.9 ±0. x.98±0.).65 (5.88).00±.00 (.5±0.5).00±.00 (.5±0.5).±.00 (8.7±0.5) CP Element.6 (9.9) Cermet.5 (8.76) C CTUTION 5 TOTL ROTTION 00 LTERNTE CTUTION 5. Cermet Plating - Terminals & :.05" ±.00 Soft Copper CD lloy 0, Plate 50 00 Microinches right Tin, Whisker-Free (RoHS) CP Plating - Terminals & :.05" ±.00 Soft Copper CD lloy 0, Plate 50 00 Microinches right Tin, Whisker-Free (RoHS) Cermet Plating - Terminal :.05" ±.00 Soft Copper CD lloy 0, No Plate CP Plating - Terminal :.05" ±.00 Soft Copper CD lloy 0, No Plate. ll drawings are shown with /8" dia. bushing with /" dia. shaft. /" dia. bushing with /8" dia. shaft is available. Locking bushing is also available.. Refer to Page 70 for Locating Lug options.. asic dimensions are in inches. Dimensions in parentheses are in millimeters. Dimensional Tolerance ±.06 (0,0), except as specified. Page 6 THE POTENTI SPECILISTS

Section : Dual module, Single (continued) 5-PC Single Potentiometer, Single DPST Rotary Switch, PC Pins.0 (5.6).75 (8.) ROTRY T.0.0 (5.6) T (.90±.0).5 (5.97).±.00 (8.7±0.5) ottom View. (.57).0.88 (.78).00 ±.07 (5.5 ±.9).09 ±.00 (.78 0.5).65 (5.88) T =.00±.00 (5.08±0.5) =.085±.005 (.6±0.) =.05±.00 (0.8±0.05) =.05±.00 (0.6±0.05) Terminal hole size:.07±.005 x.078±.005 (.9 ±0. x.98±0.).65 (5.88) (.70) CP Element.6 (9.9) Cermet.5 (8.76) C CTUTION 5 TOTL ROTTION 00 LTERNTE CTUTION 5 5-PC-90 Single Potentiometer, Single DPST Rotary Switch, PC Pins (Rotated Switch Module) T.0.0 (5.6) ROTRY.75 (8.) ROTRY. (.57) T (.90±.0).5 (5.97) ottom View.0 (5.6).09±.00 (.78±0.5).09 ±.00 (.78 0.5).00 ±.07 (5.5 ±.9).65 (5.88).±.00 (8.7±0.5) T =.00±.00 (5.08±0.5) =.085±.005 (.6±0.) =.05±.00 (0.8±0.05) =.05±.00 (0.6±0.05) Terminal hole size:.07±.005 x.078±.005 (.9 ±0. x.98±0.).65 (5.88) (.70) CP Element.6 (9.9) Cermet.5 (8.76) C CTUTION 5 TOTL ROTTION 00 LTERNTE CTUTION 5. Cermet Plating - Terminals & :.05" ±.00 Soft Copper CD lloy 0, Plate 50 00 Microinches right Tin, Whisker-Free (RoHS) CP Plating - Terminals & :.05" ±.00 Soft Copper CD lloy 0, Plate 50 00 Microinches right Tin, Whisker-Free (RoHS) Cermet Plating - Terminal :.05" ±.00 Soft Copper CD lloy 0, No Plate CP Plating - Terminal :.05" ±.00 Soft Copper CD lloy 0, No Plate. ll drawings are shown with /8" dia. bushing with /" dia. shaft. /" dia. bushing with /8" dia. shaft is available. Locking bushing is also available.. Refer to Page 70 for Locating Lug options.. asic dimensions are in inches. Dimensions in parentheses are in millimeters. Dimensional Tolerance ±.06 (0,0), except as specified. Page 7 THE POTENTI SPECILISTS

Section : Dual module, Single (continued) 5 Single Potentiometer, Single Push-Pull Switch, Solder Lugs.0 (5.6).75 (8.).0 (5.6) T.90 (7,7).5 (.8).59±.00 (9.±0.5) ottom View.0.65 (5.88).88 (.76).8 (5.56) 5 6 7 8. (.09).59±.00 (9.±0.5).8 ±.07 (8.0±.9).7 ±.00 (. 0.5).65 (5.88) T =.75±.00 (.5 0.5) =.085±.005 (.6±0.) =.05±.00 (0.8±0.05) =.00±.00 (.5±0.5) = CP Element.085±.005 (.6±0.); Cermet.5Max = CP Element.05±.00 (0.8±0.05); Cermet.05±.00 (0.6±0.05) Terminal hole size:.07±.005 x.078±.005 (.9 ±0. x.98±0.) Note: length is measured in outer position.65 (5.88) CP Element.6 (9.9) Cermet.5 (8.76) C CTUTION 5 TOTL ROTTION 00 LTERNTE CTUTION 5 5-90 Single Potentiometer, Single Push-Pull Switch, Solder Lugs (Rotated Switch Module).5 (.8).0 (5.6).75 (8.).0.0 (5.6). (.09).8 ±.07 (8.0 ±.9).90 (7,7) T.59±.00 (9.±0.5).59±.00 (9.±0.5).7 ±.00 (. 0.5) ottom View.65 (5.88) T =.75±.00 (.5 0.5) =.085±.005 (.6±0.) =.05±.00 (0.8±0.05) =.00±.00 (.5±0.5) = CP Element.085±.005 (.6±0.); Cermet.5Max = CP Element.05±.00 (0.8±0.05); Cermet.05±.00 (0.6±0.05) Terminal hole size:.07±.005 x.078±.005 (.9 ±0. x.98±0.) Note: length is measured in outer position.65 (5.88) CP Element.6 (9.9) Cermet.5 (8.76) C CTUTION 5 TOTL ROTTION 00 LTERNTE CTUTION 5. Cermet Plating - Terminals & :.05" ±.00 Soft Copper CD lloy 0, Plate 50 00 Microinches right Tin, Whisker-Free (RoHS) CP Plating - Terminals & :.05" ±.00 Soft Copper CD lloy 0, Plate 50 00 Microinches right Tin, Whisker-Free (RoHS) Cermet Plating - Terminal :.05" ±.00 Soft Copper CD lloy 0, No Plate CP Plating - Terminal :.05" ±.00 Soft Copper CD lloy 0, No Plate. ll drawings are shown with /8" dia. bushing with /" dia. shaft. /" dia. bushing with /8" dia. shaft is available. Locking bushing is also available.. Refer to Page 70 for Locating Lug options.. asic dimensions are in inches. Dimensions in parentheses are in millimeters. Dimensional Tolerance ±.06 (0,0), except as specified. Page 8 THE POTENTI SPECILISTS

Section : Dual module, Single (continued) 5-PC Single Potentiometer, Single Push-Pull Switch, PC Pins.0 (5.6).75 (8.).5 (.8) T.0.65 (5.88).88 (.76) 5 6 7 8.0 (5.6) (.90±.0).59±.00 (9.±0.5) ottom View.8 (5.56) T.59±.00 (9.±0.5). ±.07 (9.0 ±.9).5 (5.97).50 (.8).65 (5.88) T =.00±.00 (5.08±0.5) =.05±.00 (0.8±0.05) =.085±.005 (.6±0.) =.05±.00 (0.6±0.05) Terminal hole size:.07±.005 x.078±.005 (.9 ±0. x.98±0.) Note: length is measured in outer position.75 (9.5) (.70).65 (5.88) C CTUTION 5 TOTL ROTTION 00 LTERNTE CTUTION 5 5-PC-90 Single Potentiometer, Single Push-Pull Switch, PC Pins (Rotated Switch Module).5 (.8).0 (5.6).75 (8.) T.0 T. ±.07 (9.0 ±.9).59±.00 (9.±0.5) (.90±.0).5 (5.97).50 (.8).0 (5.6).59±.00 (9.±0.5) ottom View.65 (5.88) T =.00±.00 (5.08±0.5) =.05±.00 (0.8±0.05) =.085±.005 (.6±0.) =.05±.00 (0.6±0.05) Terminal hole size:.07±.005 x.078±.005 (.9 ±0. x.98±0.) Note: length is measured in outer position.65 (5.88) (.70) CP Element.6 (9.9) Cermet.5 (8.76).085±.005 (.6±0.) C CTUTION 5 TOTL ROTTION 00 LTERNTE CTUTION 5. Cermet Plating - Terminals & :.05" ±.00 Soft Copper CD lloy 0, Plate 50 00 Microinches right Tin, Whisker-Free (RoHS) CP Plating - Terminals & :.05" ±.00 Soft Copper CD lloy 0, Plate 50 00 Microinches right Tin, Whisker-Free (RoHS) Cermet Plating - Terminal :.05" ±.00 Soft Copper CD lloy 0, No Plate CP Plating - Terminal :.05" ±.00 Soft Copper CD lloy 0, No Plate. ll drawings are shown with /8" dia. bushing with /" dia. shaft. /" dia. bushing with /8" dia. shaft is available. Locking bushing is also available.. Refer to Page 70 for Locating Lug options.. asic dimensions are in inches. Dimensions in parentheses are in millimeters. Dimensional Tolerance ±.06 (0,0), except as specified. Page 9 THE POTENTI SPECILISTS

Section : Dual module, Single (continued) 6 Potentiometer with Vernier Drive, Single, Solder Lugs.78 T (9.89).60±.07 (9.6±.9 ).00±.00 (.5±0.5) 6-PC Potentiometer with Vernier Drive, Single, Solder Pins.0.00±.00 (.5±0.5).0 (5.6) T =.75±.00 (.5±0.5) = CP Element.085±.005 (.6±0.); Cermet.5Max = CP Element.05±.00 (0.8±0.05); Cermet.05±.00 (0.6±0.05) = CP Element.5 (8.76); Cermet.6 (9.9) Terminal hole size:.07±.005 x.078±.005 (.9 ±0. x.98±0.).0.65 (5.88).65 (5.88).65 (5.88).80 T (0.7).85±.07 (0.0±.9 ) T.75 (9.5).65 (5.88).085±.005 (.6±0.) (.70) T =.00±.00 (5.08±0.5) =.05±.00 (0.6±0.05). Cermet Plating - Terminals & :.05" ±.00 Soft Copper CD lloy 0, Plate 50 00 Microinches right Tin, Whisker-Free (RoHS) CP Plating - Terminals & :.05" ±.00 Soft Copper CD lloy 0, Plate 50 00 Microinches right Tin, Whisker-Free (RoHS) Cermet Plating - Terminal :.05" ±.00 Soft Copper CD lloy 0, No Plate CP Plating - Terminal :.05" ±.00 Soft Copper CD lloy 0, No Plate. ll drawings are shown with /8" dia. bushing with /" dia. shaft. /" dia. bushing with /8" dia. shaft is available. Locking bushing is also available.. Refer to Page 70 for Locating Lug options.. asic dimensions are in inches. Dimensions in parentheses are in millimeters. Dimensional Tolerance ±.06 (0,0), except as specified. Page 0 THE POTENTI SPECILISTS

Section : Dual module, Concentric 7 Dual Potentiometer, Concentric, Solder Lugs Inner T Outer T.0±.07 (6.9±.9 ).5 (5.6) E ±.0.00±.00 (.5±0.5).00±.00 (.5±0.5).0 Mounting Surface T =.75±.00 (.5±0.5) =.75±.00 (6.98±0.5) = CP Element.085±.005 (.6±0.); Cermet.5Max = CP Element.05±.00 (0.8±0.05); Cermet.05±.00 (0.6±0.05) = CP Element.5 (8.76); Cermet.6 (9.9) Terminal hole size:.07±.005 x.078±.005 (.9 ±0. x.98±0.).0 (5.6).65 (5.88).65 (5.88) 7-PC Dual Potentiometer, Concentric, Solder Pins Inner Outer E±.0 (± 0.80 ) T.0 Mounting Surface.75 (9.5) (.70).65 (5.88).65 (5.88).085±.005 (.6±0.) T T.8±.07 (8.0±.9 ).5(5.97) T =.00±.00 (5.08±0.5) =.00±.00 (7.6±0.5) =.05±.00 (0.6±0.05). Cermet Plating - Terminals & :.05" ±.00 Soft Copper CD lloy 0, Plate 50 00 Microinches right Tin, Whisker-Free (RoHS) CP Plating - Terminals & :.05" ±.00 Soft Copper CD lloy 0, Plate 50 00 Microinches right Tin, Whisker-Free (RoHS) Cermet Plating - Terminal :.05" ±.00 Soft Copper CD lloy 0, No Plate CP Plating - Terminal :.05" ±.00 Soft Copper CD lloy 0, No Plate. ll drawings are shown with /8" dia. bushing with /" dia. shaft. /" dia. bushing with /8" dia. shaft is available. Locking bushing is also available.. Refer to Page 70 for Locating Lug options.. asic dimensions are in inches. Dimensions in parentheses are in millimeters. Dimensional Tolerance ±.06 (0,0), except as specified. Page THE POTENTI SPECILISTS

Section : Dual module, Concentric (continued) 8 Single Potentiometer, Push-Pull Switch, Concentric, Solder Lugs.0 (5.6).75 (8.).0 (5.6) Inner Outer T E ±.0.5 (5,6).5 (.8).59±.00 (9.±0.5) ottom View.0.65 (5.88).88 (.76).8 (5.56) 5 6 7 8. (.09).59±.00 (9.±0.5).0 ±.07 (6.9 ±.9).7 ±.00 (. ± 0.5).65 (5.88) T =.75 ±.00 (.5 ± 0.5) =.085±.005 (.6±0.) =.05±.00 (0.8±0.05) =.00±.00 (.5±0.5) = CP Element.085±.005 (.6±0.); Cermet.5Max = CP Element.05±.00 (0.8±0.05); Cermet.05±.00 (0.6±0.05) Terminal hole size:.07±.005 x.078±.005 (.9 ±0. x.98±0.) Note: length is measured in outer position.65 (5.88) CP Element.6 (9.9) Cermet.5 (8.76) C CTUTION 5 TOTL ROTTION 00 LTERNTE CTUTION 5 8-90 Single Potentiometer, Push-Pull Switch, Concentric, Solder Lugs (Rotated Switch Module) Inner.59±.00 (9.±0.5) Outer T E ±.0.90 (7,7).5 (.8).0 (5.6).75 (8.).0 (5.6).0.0 ±.07 (6.9 ±.9) ottom View T =.75 ±.00 (.5 ± 0.5) =.085±.005 (.6±0.) =.05±.00 (0.8±0.05) =.00±.00 (.5±0.5) = CP Element.085±.005 (.6±0.); Cermet.5Max = CP Element.05±.00 (0.8±0.05); Cermet.05±.00 (0.6±0.05) Terminal hole size:.07±.005 x.078±.005 (.9 ±0. x.98±0.) Note: length is measured in outer position.65 (5.88).65 (5.88) CP Element.6 (9.9) Cermet.5 (8.76) C CTUTION 5 TOTL ROTTION 00 LTERNTE CTUTION 5. Cermet Plating - Terminals & :.05" ±.00 Soft Copper CD lloy 0, Plate 50 00 Microinches right Tin, Whisker-Free (RoHS) CP Plating - Terminals & :.05" ±.00 Soft Copper CD lloy 0, Plate 50 00 Microinches right Tin, Whisker-Free (RoHS) Cermet Plating - Terminal :.05" ±.00 Soft Copper CD lloy 0, No Plate CP Plating - Terminal :.05" ±.00 Soft Copper CD lloy 0, No Plate. ll drawings are shown with /8" dia. bushing with /" dia. shaft. /" dia. bushing with /8" dia. shaft is available. Locking bushing is also available.. Refer to Page 70 for Locating Lug options.. asic dimensions are in inches. Dimensions in parentheses are in millimeters. Dimensional Tolerance ±.06 (0,0), except as specified. Page THE POTENTI SPECILISTS

Section : Dual module, Concentric (continued) 8-PC Single Potentiometer, Push-Pull Switch, Concentric, PC Pins.0 (5.6).75 (8.).0 (5.6) Inner Outer T E ±.0 (.90±.0).5 (5.97).5 (.8).59±.00 (9.±0.5) ottom View.0.65 (5.88).88 (.76).8 (5.56) 5 6 7 8.0.88 (.78).068 ±.07 (7. ±.9).09 ±.00 (.78 0.5).65 (5.88) T =.00±.00 (5.08±0.5) =.085±.005 (.6±0.) =.05±.00 (0.8±0.05) =.00±.00 (.5±0.5) Terminal hole size:.07±.005 x.078±.005 (.9 ±0. x.98±0.).65 (5.88) (.70) CP Element.6 (9.9) Cermet.5 (8.76) C CTUTION 5 TOTL ROTTION 00 LTERNTE CTUTION 5 8-PC-90 Single Potentiometer, Push-Pull Switch, Concentric, PC Pins (Rotated Switch Module) Inner.59±.00 (9.±0.5) Outer E ±.0 (.90±.0).5 (.8) T.0 T.5 (5.97) ottom View.068 ±.07 (7. ±.9).65 (5.88) T =.00±.00 (5.08±0.5) =.085±.005 (.6±0.) =.05±.00 (0.8±0.05) =.05±.00 (0.6±0.05) Terminal hole size:.07±.005 x.078±.005 (.9 ±0. x.98±0.).65 (5.88) CP Element.6 (9.9) Cermet.5 (8.76) C CTUTION 5 TOTL ROTTION 00 LTERNTE CTUTION 5. Cermet Plating - Terminals & :.05" ±.00 Soft Copper CD lloy 0, Plate 50 00 Microinches right Tin, Whisker-Free (RoHS) CP Plating - Terminals & :.05" ±.00 Soft Copper CD lloy 0, Plate 50 00 Microinches right Tin, Whisker-Free (RoHS) Cermet Plating - Terminal :.05" ±.00 Soft Copper CD lloy 0, No Plate CP Plating - Terminal :.05" ±.00 Soft Copper CD lloy 0, No Plate. ll drawings are shown with /8" dia. bushing with /" dia. shaft. /" dia. bushing with /8" dia. shaft is available. Locking bushing is also available.. Refer to Page 70 for Locating Lug options.. asic dimensions are in inches. Dimensions in parentheses are in millimeters. Dimensional Tolerance ±.06 (0,0), except as specified. Page THE POTENTI SPECILISTS

Section : Dual module, Concentric (continued) 9 Single Potentiometer, Rotary Switch, Concentric, Solder Lugs.0 (5.6).75 (8.) Inner ROTRY Outer.5 (.8).0.0 (5.6) E ±.0.±.00 (8.7±0.5). (.57) T.5 (5.6) ottom View.09 ±.00 (.78 0.5).05 ±.07 (6.7 ±.9).50 ±.00 (6.5 ± 0.5).65 (5.88) T =.75 ±.00 (.5 0.5) =.085±.005 (.6±0.) =.05±.00 (0.8±0.05) = CP Element.085±.005 (.6±0.); Cermet.5Max = CP Element.05±.00 (0.8±0.05); Cermet.05±.00 (0.6±0.05) Terminal hole size:.07±.005 x.078±.005 (.9 ±0. x.98±0.) Note: length is measured in outer position.65 (5.88).00±.00 (.5±0.5).00±.00 (.5±0.5) CP Element.6 (9.9) Cermet.5 (8.76) C CTUTION 5 TOTL ROTTION 00 LTERNTE CTUTION 5 9-90 Single Potentiometer, Rotary Switch, Concentric, Solder Lugs (Rotated Switch Module) Inner Outer.5 (.8) ROTRY.0.0 (5.6).75 (8.) ROTRY. (.57) T E ±.0.5 (5.6).0 (5.6).09±.00 (.78±0.5).09 ±.00 (.78 0.5).05 ±.07 (6.7 ±.9).50 ±.00 (6.5 0.5) ottom View.65 (5.88) T =.75 ±.00 (.5 0.5) =.085±.005 (.6±0.) =.05±.00 (0.8±0.05) = CP Element.085±.005 (.6±0.); Cermet.5Max = CP Element.05±.00 (0.8±0.05); Cermet.05±.00 (0.6±0.05) Terminal hole size:.07±.005 x.078±.005 (.9 ±0. x.98±0.) Note: length is measured in outer position.65 (5.88).00±.00 (.5±0.5).00±.00 (.5±0.5).±.00 (8.7±0.5) CP Element.6 (9.9) Cermet.5 (8.76) C CTUTION 5 TOTL ROTTION 00 LTERNTE CTUTION 5. Cermet Plating - Terminals & :.05" ±.00 Soft Copper CD lloy 0, Plate 50 00 Microinches right Tin, Whisker-Free (RoHS) CP Plating - Terminals & :.05" ±.00 Soft Copper CD lloy 0, Plate 50 00 Microinches right Tin, Whisker-Free (RoHS) Cermet Plating - Terminal :.05" ±.00 Soft Copper CD lloy 0, No Plate CP Plating - Terminal :.05" ±.00 Soft Copper CD lloy 0, No Plate. ll drawings are shown with /8" dia. bushing with /" dia. shaft. /" dia. bushing with /8" dia. shaft is available. Locking bushing is also available.. Refer to Page 70 for Locating Lug options.. asic dimensions are in inches. Dimensions in parentheses are in millimeters. Dimensional Tolerance ±.06 (0,0), except as specified. Page THE POTENTI SPECILISTS

Section : Dual module, Concentric (continued) 9-PC Single Potentiometer, Rotary Switch, Concentric, Solder Lugs.0 (5.6).75 (8.) Inner ROTRY Outer.5 (.8) T.0.±.00 (8.7±0.5).0 (5.6) E ±.0. (.57) T (.90±.0).5 (5.97) ottom View.88 (.78).0 ±.07 (7.99 ±.9).09 ±.00 (.78 0.5).65 (5.88) T =.00±.00 (5.08±0.5) =.05±.00 (0.8±0.05) =.085±.005 (.6±0.) =.05±.00 (0.6±0.05) Terminal hole size:.07±.005 x.078±.005 (.9 ±0. x.98±0.).65 (5.88) (.70) CP Element.6 (9.9) Cermet.5 (8.76) C CTUTION 5 TOTL ROTTION 00 LTERNTE CTUTION 5 9-PC-90 Single Potentiometer, Rotary Switch, Concentric, Solder Lugs (Rotated Switch Module) Inner Outer.5 (.8) ROTRY T.0.0 (5.6).75 (8.) ROTRY. (.57) E ±.0.0 (5.6) T (.90±.0).5 (5.97) ottom View.09±.00 (.78±0.5).09 ±.00 (.78 0.5).0 ±.07 (7.99 ±.9).65 (5.88).±.00 (8.7±0.5) T =.00±.00 (5.08±0.5) =.05±.00 (0.8±0.05) =.085±.005 (.6±0.) =.05±.00 (0.6±0.05) Terminal hole size:.07±.005 x.078±.005 (.9 ±0. x.98±0.).65 (5.88) (.70) CP Element.6 (9.9) Cermet.5 (8.76) C CTUTION 5 TOTL ROTTION 00 LTERNTE CTUTION 5. Cermet Plating - Terminals & :.05" ±.00 Soft Copper CD lloy 0, Plate 50 00 Microinches right Tin, Whisker-Free (RoHS) CP Plating - Terminals & :.05" ±.00 Soft Copper CD lloy 0, Plate 50 00 Microinches right Tin, Whisker-Free (RoHS) Cermet Plating - Terminal :.05" ±.00 Soft Copper CD lloy 0, No Plate CP Plating - Terminal :.05" ±.00 Soft Copper CD lloy 0, No Plate. ll drawings are shown with /8" dia. bushing with /" dia. shaft. /" dia. bushing with /8" dia. shaft is available. Locking bushing is also available.. Refer to Page 70 for Locating Lug options.. asic dimensions are in inches. Dimensions in parentheses are in millimeters. Dimensional Tolerance ±.06 (0,0), except as specified. Page 5 THE POTENTI SPECILISTS

Section : Dual module, Concentric (continued) 0 Potentiometer with Vernier Drive, Concentric, Solder Lugs.78 T (9.89).75±.07 (9.85±.9 ) E ±.0 ( 0.80 ).00±.00 (.5±0.5).0.00±.00 (.5±0.5).0 (5.6) T =.75±.00 (.5±0.5) = CP Element.085±.005 (.6±0.); Cermet.5Max = CP Element.05±.00 (0.8±0.05); Cermet.05±.00 (0.6±0.05) = CP Element.5 (8.76); Cermet.6 (9.9) Terminal hole size:.07±.005 x.078±.005 (.9 ±0. x.98±0.).65 (5.88).65 (5.88) 0-PC Potentiometer with Vernier Drive, Concentric, Solder Pins.0.65 (5.88).80 T (0.7).00±.07 (0.8±.9 ) E ±.0 ( 0.80 ) T.75 (9.5).65 (5.88).085±.005 (.6±0.) (.70) T =.00±.00 (5.08±0.5) =.05±.00 (0.6±0.05) The inner shaft (.078 [.98 mm] diameter) is for the coarse adjustment, the outer shaft for the fine adjustment. Rotary Switch, Push-Pull/Momentary Switch, Concentric, Solder Lugs.0 (5.6).75 (8.).65 (9.).0 (5.6).59±.00 (9.±0.5) Inner Push-Pull Switch Outer Rotary Switch E ±.0 ( 0.80 ).66 (6.76).09±.00 (.78±0.5).5 (.8) T.8 (5.56) 5 6 7 8.59 (9.) T ottom View.0.05±0 (6.7±0.80).65 (5.88) T =.085±.005 (.6±0.) =.05±.00 (0.8±0.05) Terminal hole size:.07±.005 x.078±.005 (.9 ±0. x.98±0.) Note: length is measured in outer position.65 (5.88) TOTL ROTTION 00. (.57).±.00 (8.7±0.5) C CTUTION 5 LTERNTE CTUTION 5. Cermet Plating - Terminals & :.05" ±.00 Soft Copper CD lloy 0, Plate 50 00 Microinches right Tin, Whisker-Free (RoHS) CP Plating - Terminals & :.05" ±.00 Soft Copper CD lloy 0, Plate 50 00 Microinches right Tin, Whisker-Free (RoHS) Cermet Plating - Terminal :.05" ±.00 Soft Copper CD lloy 0, No Plate CP Plating - Terminal :.05" ±.00 Soft Copper CD lloy 0, No Plate. ll drawings are shown with /8" dia. bushing with /" dia. shaft. /" dia. bushing with /8" dia. shaft is available. Locking bushing is also available.. Refer to Page 70 for Locating Lug options.. asic dimensions are in inches. Dimensions in parentheses are in millimeters. Dimensional Tolerance ±.06 (0,0), except as specified. Page 6 THE POTENTI SPECILISTS

Section : Triple module, Single Triple Potentiometer, Single, Solder Lugs T T.±.07 (.±.9 ) T.5 (5.6).00±.00 (.5±0.5).0.00±.00 (.5±0.5) T =.75±.00 (.5±0.5) =.00±.00 (5.08±0.5) = CP Element.085±.005 (.6±0.); Cermet.5Max = CP Element.05±.00 (0.8±0.05); Cermet.05±.00 (0.6±0.05) = CP Element.5 (8.76); Cermet.6 (9.9) Terminal hole size:.07±.005 x.078±.005 (.9 ±0. x.98±0.).0 (5.6).65 (5.88).65 (5.88) -PC Triple Potentiometer, Single, Solder Pins.0.65 (5.88) T T T T T (.90±.0).5 (5.97) T T =.00±.00 (5.08±0.5) =.05±.00 (0.6±0.05) Mounting Surface.75 (9.5) (.70).65 (5.88).085±.005 (.6±0.).8±.07 (6.0±.9 ). Cermet Plating - Terminals & :.05" ±.00 Soft Copper CD lloy 0, Plate 50 00 Microinches right Tin, Whisker-Free (RoHS) CP Plating - Terminals & :.05" ±.00 Soft Copper CD lloy 0, Plate 50 00 Microinches right Tin, Whisker-Free (RoHS) Cermet Plating - Terminal :.05" ±.00 Soft Copper CD lloy 0, No Plate CP Plating - Terminal :.05" ±.00 Soft Copper CD lloy 0, No Plate. ll drawings are shown with /8" dia. bushing with /" dia. shaft. /" dia. bushing with /8" dia. shaft is available. Locking bushing is also available.. Refer to Page 70 for Locating Lug options.. asic dimensions are in inches. Dimensions in parentheses are in millimeters. Dimensional Tolerance ±.06 (0,0), except as specified. Page 7 THE POTENTI SPECILISTS