Main Components 0 0 0 0 Cap 0 Pin Washer 0 Compression Spring Pivot Pin 0 Roller Pin 00 Roller Soc. Hd. Cap Screw, /" - 0 x /" Plunger Stop 0 0 Compression Spring () 0 Post Assembly (Incls. Refs.,,, ) 0 Rack w/pins (Incls. Refs., ) Spring Pin () 0 Ball Detente 0 Crank Screw Assembly 0 Friction Ring 0 Chain Hook Spring Pin Retaining Ring 0 0 Base w/pins (Incls. Ref. ) 0 Spring Pin () Chain Assembly (Incls. Ref., ) 0 RIDGID, Inc. Printed 0/ The Emerson logo and RIDGID logo are registered trademarks of Emerson Electric Co. or RIDGID, Inc. in the U.S. and other countries. --0.0 EC0 All other trademarks belong to their respective holders.
Transmission 0 0 0 0 0 O-Ring 0 Grease Seal Plunger Assembly 0 Adjusting Cap 0 Bearing () Set Screw, Nylon Tip Rear Gear Case 00 Feed Shaft 0 Carriage Pinion 0 Roll Pin Hand Wheel Carry Handle Roll Pin 00 Screws () Front Gear Case Chuck Guard Screw () Needle Bearing Thrust Bearing Assembly 0 0 Spiral Gear Set Ball Bearing O-Ring Retaining Ring, Internal Spacer 0 Chuck w/key Gasket, Transmission Ball Bearing nd Intermediate Gear Assembly Ball Bearing () 0 st Intermediate Gear Assembly Ball Bearing 0 Retaining Ring Ball Bearing 0 Transmission Grease, Lb. 0 Chuck Key Service Notes: Ref. Backlash Adjustment Use " C-Clamp to lightly push chuck into housing. Apply thin coat of Loctite No. Hydraulic/Pneumatic Thread Sealant (or equivalent) to threads on adjusting cap, Ref. Tighten cap to 0-0 in-lbs then back off to eliminate torque. Re-tighten finger tight then back off 0 to 0. Remove clamp and check by gripping chuck with fingertips and feeling for minimal rotational backlash in output gear. Tighten set screw, Ref., to hold cap securely. Ref. Grease Fill Use only recommended transmission grease (Molytex EPO). Fill bearing pockets with grease and apply coating to gear teeth. Fill two separate transmission cavities approximately / full of grease using about / of pound can
Motor Type 0 0 00 Screw, Self Tapping () 0 End Cap 0 Bumper () 0 Brush Assembly Set V 0 Brush Assembly Set 0V 0 Screw, #0- x " Soc. Hd. Cap () 0 Insulator Warning Label Set 0 Motor Housing Field V Field 0V Field 00V 0 0 Motor Lead Set Fan Shroud 0 Seal 0 O-Ring Bearing Armature Sleeve 0 Bearing 0 Armature Assembly V 0 Armature Assembly 0V 0 Armature Assembly 00V Rubber Sleeve Service Note: When replacing early style V or 0V armature# or field# you must replace with both new style armature#, field# and brushes#.
Motor Type Motors built after serial number EBH XXXXX 0 0 00 Screw, Self Tapping () 0 End Cap 0 Bumper 0 Brushes V 0 Brush Kit 0V 0 Screw, #0- x " Soc. Hd. Cap () 00 Shields () 0 Insulator 0 Motor Housing Warning Label Set 0 Field V Field 0V Field 00V Washer Fan Shroud 0 Seal 0 O-Ring Bearing Armature Sleeve Armature Assembly 0V Armature Assembly 0V Armature Assembly 00V 0 Bearing Rubber Sleeve
V Components 0 0 Key Retainer 00 Line Cord w/gfi Ring Terminal 0 Screw w/washer Lock Nut, /" NPT 0 Switch Box Cover 00 Cord Guard 0 Strain Relief Screw #0 - x /" () 0 Wire Nut Switch Quick Disconnect, Right Angle () 0 Circuit Breaker, Amp
0V Components 0 0 Key Retainer Line Cord Ring Terminal 0 Screw w/washer () Quick Disconnect, Right Angle () 0 Suppressor 00 Ring Terminal () 0 Washer Terminal Block 0 0 Switch Box Cover Pop Rivet /" () 00 Cord Guard 0 Strain Relief Screw #0 - x /" () Wire Nut Switch Lock Nut, /" NPT Circuit Breaker, Amp 0 V Soft Start Assy.
00V Components 0 0 Key Retainer Line Cord Ring Terminal 0 Screw w/washer () Lock Nut, /" NPT 0 Switch Box Cover 00 Cord Guard 0 Strain Relief Screw #0 - x /" () 0 Wire Nut Switch Quick Disconnect, Right Angle () Circuit Breaker, Amp
0V Wiring Diagram 0V Wiring Diagram (w/soft Start) 00V/V Wiring Diagram