INSTALL GUIDE DOCUMENT NUMBER 5644 REVISI DATE 084 FIRMWARE OEM-AL(RS)-CH8-[FLCAN] HARDWARE FLCAN ESSORIES FLPROG (REQUIRED) TERMS OF USE: Automotive Data Solutions Inc. ( ADS ) products are strictly intended for installation by Certified Technicians who are employed by a registered business specialized in the installation of automotive aftermarket electronics products. Prior to beginning installation of an ADS product in a vehicle, it is the Certified Technician s responsibility to review the most current Product Guide, Install Guide and vehicle-specific notes available in Weblink. ADS is not responsible for any damages whatsoever, including but not limited to any consequential damages, incidental damages, damages for loss of time, loss of earnings, loss of profit, commercial loss, loss of economic opportunity and the like that may or may not have resulted from the use, misuse, improper installation or operation of its products. ADS reserves itself the right to suspend any Weblink account without notice and decline to offer technical support to non-certified Technicians, non-compliant Certified Technicians or end users. BEFORE INSTALLATI - Connect module to computer - Login to Weblink account - Flash firmware to module (module is not preloaded with firmware) 4- Use accessories accordingly (accessories are sold separately)
VEHICLE LIST - OF PAGE OF 7 FEATURES MAKE MODEL I NOTE WARNING: All vehicle doors must be closed and locked prior to remote start sequence. YEAR INSTALL TYPE DATA IMMOBILIZER BYPASS X LOCK /STANDALE MOD. DOOR LOCK DOOR UNLOCK ARM OEM ALARM DISARM OEM ALARM TRUNK/HATCH RELEASE DOOR STATUS OUTPUT TRUNK STATUS OUTPUT BRAKE PEDAL STATUS OUTPUT TACHOMETER OUTPUT SECURE TAKEOVER GLOW PLUGS STATUS RAP SHUTDOWN CTRL RAM 500 / 500 / 500 STD key (Tip-Start) AT -7 500 / 500 / 500 STD key (Tip-Start) AT 8 500 / 500 / 500 Diesel STD key (Tip-Start) AT 4-7 500 / 500 / 500 Diesel STD key (Tip-Start) AT 8
BOX CTENTS - OF PAGE OF 7 DOC.: #5644 084 BOX CTENTS MODULE 6 PIN WHITE CNECTOR 4 PIN BLACK CNECTOR WHITE 4 5 6 PROGRAMMING BUTT LED 7 PIN WHITE CNECTOR 0 PIN BLACK CNECTOR WHITE WHITE 4 5 6 7 A B C F 0 9 8 7 6 5 4 BLACK PIN WHITE CNECTOR DATA CABLE BLUE D E 4 BLACK DATA PORT (WEBLINK, RF, TELEMATIC) PIN BLUE CNECTOR DATA CABLE WEBLINK CABLE (required accessory sold separately) WEBLINK CABLE MODULE DATA PORT COMPUTER USB PORT 4 PIN BLACK CABLE
TYPE - WIRE CHART - OF PAGE 4 OF 7 MAKE MODEL YEAR WIRE DESCRIPTI CNECTOR NAME CNECTOR COLOR CNECTOR TYPE RAM POSITI WIRE COLOR POLARITY MODULE LOCATI COMPENT LOCATOR 500 / 500 Diesel STD key AT 500 / 500 Diesel / 500 / 500 Diesel / STD key AT -7-7 V D664A Black 06 pin 06 Red (+) Ignition connector F Ground D664A Black 06 pin 0 Black (-) Ignition connector F Key position D664A Black 06 pin 04 Purple/Brown (MUX) Ignition connector F Imo Lin D664A Black 06 pin 05 White/Green (DATA) Ignition connector F CanH D7405A Black 6 pin 06 Gray/White (DATA) OBDII connector ~ CanL D7405A Black 6 pin 4 Yellow (DATA) OBDII connector ~ Parking Light D4A Black 0 pin 0 White/Brown (MUX) Parking light switch A V D664A Black 06 pin 06 Red (+) Ignition connector F Ground D664A Black 06 pin 0 Black (-) Ignition connector F Key position D664A Black 06 pin 04 Purple/Brown (MUX) Ignition connector F Imo Lin D664A Black 06 pin 05 White/Green (DATA) Ignition connector F CanH D7405A Black 6 pin 06 Gray/White (DATA) OBDII connector ~ CanL D7405A Black 6 pin 4 Yellow (DATA) OBDII connector ~ Parking Light D4A Black 0 pin 0 White/Brown (MUX) Parking light switch A
TYPE - WIRING DIAGRAM - OF PAGE 5 OF 7 M M M M4 M6 M5 DATA GROUND (-) - 0 KEY POSITI (MUX) - 04 IMO LIN - 05 6 5 4 PTS SWITCH M 0 GRAY/YELLOW (NC) 0 GRAY/RED (NC) 0 GREEN/YELLOW (NC) 04 GREEN/RED (NC) 05 BLUE/YELLOW (NC) 06 BLUE/RED (NC) 7.5A V (+) - 06 CANL - 4 4 5 6 7 8 OBDII CNECTOR M 0 PINK - KEY POSITI (MUX) INPUT 0 PINK/BLACK (NC) 0 ORANGE - KEY POSITI (MUX) OUTPUT 04 ORANGE/WHITE (NC) 05 ORANGE/BLACK - IMO LIN 06 BROWN/YELLOW - CANL 07 BROWN/RED - CANH CANH - 06 9 BLACK 0 4 5 6 PARKING LIGHT SWITCH M 0 YELLOW - PARKING LIGHT (MUX) OUTPUT 0 YELLOW/RED (NC) 0 YELLOW/BLACK (NC) PARKING LIGHT (MUX) - 0 4 5 M4 0 WHITE (NC) 0 WHITE/RED - LIN CUT VEHICLE SIDE 0 WHITE/BLACK - LIN CUT CNECTOR SIDE 6 7 8 9 0 M5 0 BLUE/WHITE (NC) 0 WHITE (NC) 0 BLACK - GROUND 04 RED - V (+) WITHOUT A COMPATIBLE ESSORY OR M5 DATA CABLE COMPATIBLE ESSORY WITH A COMPATIBLE ESSORY. IMPORTANT: SEE THE COMPATIBLE ESSORIES PAGE FOR DETAILS. M6 0 GREEN/BLACK- HOOD STATUS (-) INPUT 0 BLUE/BLACK (NC) 0 RED/WHITE (NC) 04 BROWN (NC) 05 PURPLE/YELLOW (NC) 06 PURPLE/BLACK (NC) 07 WHITE (NC) 08 BLACK/WHITE (NC) 09 GREEN (NC) 0 PURPLE/WHITE (NC) HOOD SWITCH INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLE IS NOT EQUIPPED WITH E.
TYPE - WIRE CHART - OF PAGE 6 OF 7 MAKE MODEL YEAR WIRE DESCRIPTI CNECTOR NAME CNECTOR COLOR CNECTOR TYPE RAM POSITI WIRE COLOR POLARITY MODULE LOCATI COMPENT LOCATOR 500 / 500 / 500 STD key AT 500 Diesel / 500 Diesel / 500 Diesel STD key AT 8 8 V D664A Black 06 pin 06 Red (+) Ignition connector ~ Ground D664A Black 06 pin 0 Black (-) Ignition connector ~ Key position D664A Black 06 pin 04 Purple/Brown (MUX) Ignition connector ~ Imo Lin D664A Black 06 pin 05 White/Green (DATA) Ignition connector ~ CanH ~ Gray 0 pin 0 Orange (DATA) Trailer module, right of steering column ~ CanL ~ Gray 0 pin 0 Yellow (DATA) Trailer module, right of steering column ~ Parking Light D4A Black 0 pin 0 White/Brown (MUX) Parking light switch ~ V D664A Black 06 pin 06 Red (+) Ignition connector ~ Ground D664A Black 06 pin 0 Black (-) Ignition connector ~ Key position D664A Black 06 pin 04 Purple/Brown (MUX) Ignition connector ~ Imo Lin D664A Black 06 pin 05 White/Green (DATA) Ignition connector ~ CanH ~ Gray 0 pin 0 Orange (DATA) Trailer module, right of steering column ~ CanL ~ Gray 0 pin 0 Yellow (DATA) Trailer module, right of steering column ~ Parking Light D4A Black 0 pin 0 White/Brown (MUX) Parking light switch ~
TYPE - WIRING DIAGRAM - OF PAGE 7 OF 7 M M M M4 M6 M5 DATA GROUND (-) - 0 KEY POSITI (MUX) - 04 IMO LIN - 05 6 5 4 PTS SWITCH M M 0 GRAY/YELLOW (NC) 0 GRAY/RED (NC) 0 GREEN/YELLOW (NC) 04 GREEN/RED (NC) 05 BLUE/YELLOW (NC) 06 BLUE/RED (NC) 0 PINK - KEY POSITI (MUX) INPUT 0 PINK/BLACK (NC) 0 ORANGE - KEY POSITI (MUX) OUTPUT 04 ORANGE/WHITE (NC) 05 ORANGE/BLACK - IMO LIN 06 BROWN/YELLOW - CANL 07 BROWN/RED - CANH 7.5A V (+) - 06 CANL - 0 CANH - 0 GRAY 6 BLACK 7 8 4 9 5 0 TRAILER PACK CNECTOR PARKING LIGHT SWITCH M M4 0 YELLOW - PARKING LIGHT (MUX) OUTPUT 0 YELLOW/RED (NC) 0 YELLOW/BLACK (NC) 0 WHITE (NC) 0 WHITE/RED - LIN CUT VEHICLE SIDE 0 WHITE/BLACK - LIN CUT CNECTOR SIDE PARKING LIGHT (MUX) - 0 4 5 6 7 8 9 0 M5 0 BLUE/WHITE (NC) 0 WHITE (NC) 0 BLACK - GROUND 04 RED - V (+) WITHOUT A COMPATIBLE ESSORY OR M5 DATA CABLE COMPATIBLE ESSORY WITH A COMPATIBLE ESSORY. IMPORTANT: SEE THE COMPATIBLE ESSORIES PAGE FOR DETAILS. M6 0 GREEN/BLACK- HOOD STATUS (-) INPUT 0 BLUE/BLACK (NC) 0 RED/WHITE (NC) 04 BROWN (NC) 05 PURPLE/YELLOW (NC) 06 PURPLE/BLACK (NC) 07 WHITE (NC) 08 BLACK/WHITE (NC) 09 GREEN (NC) 0 PURPLE/WHITE (NC) HOOD SWITCH INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLE IS NOT EQUIPPED WITH E.
MODULE PROGRAMMING PROCEDURE - OF PAGE 8 OF 7 0 Close driver door. Re-open driver door to wake up data bus. 07 Remove key. Connect module to computer and proceed with extended programming. 0 Press Unlock on OEM remote. If the vehicle is not equipped with an OEM remote, press the module programming button. 08 Insert key into ignition. 4 WARNING: Do not press module programming button. Connect power first. Connect module to vehicle. 0 Wait, LED will flash GREEN once [x]. If LED does not flash GREEN, press Unlock on OEM remote again. 09 Turn key to position. 5 Turn key to position. 04 Turn key to position. 0 Wait, LED will flash GREEN. 6 Wait, LED will turn solid GREEN for seconds. 05 Wait, LED will turn solid RED. Turn key to position. 7 Turn key to position. 06 Turn key to position. WARNING: Disconnect power last. Disconnect module from vehicle. 8 Turn key to position.
MODULE PROGRAMMING PROCEDURE - OF PAGE 9 OF 7 9 Turn key to position. 0 Module Programming Procedure completed.
VALET MODE PROGRAMMING PROCEDURE - OF PAGE 0 OF 7 NOTE: In Valet Mode, the Remote starter is not functional. Keyless entry, Lock and Unlock will remain functional. See RF kit user manual for alternate valet mode programming. To exit valet mode: repeat steps to 5. 0 Time restriction. Complete next step within 7 seconds. 0 Cycle ignition five times [5x /] rapidly. ENGINE STOP 0 Wait, LED will turn solid RED for seconds. 04 Set ignition to position. ENGINE STOP 05 Valet Mode Programming Procedure completed.
PAGE OF 7 MODULE NAVIGATI PROCEDURE - OF It is mandatory to exit the Module Navigation at the end of this procedure. Failure to exit the Module Navigation will drain vehicle battery. To exit the Module Navigation at any time: Follow STEP. 04 Module must be programmed to the vehicle. 05 Use the Module Navigation Chart on the next page. 06 Set ignition to position. 07 TO ESS THE MENUS: Press and hold programming button until LED turns solid GREEN. 08 IN THE MENUS: Press the programming button as many times as the menu number indicates. LED will flash GREEN an equal amount of times continuously. 09 0 DOC.: #5644 084 TO ESS THE OPTIS: Press and hold programming button until LED turns solid RED. 0 IN THE OPTIS: Press the programming button as many times as the option number indicates. LED will flash RED an equal amount of times continuously. TO ESS THE SETTINGS: Press and hold programming button until LED turns solid GREEN. Configure every other setting and proceed to step. [Z] LED will flash GREEN as many times as the current (or default) setting number, continuously. MANDATORY: EXIT MODULE NAVIGATI. Press and hold programming button for 7 seconds. LED will flash RED rapidly. Release programming button. LED will turn. [Z] IN THE SETTINGS: Press the programming button as many times as necessary to access your setting. LED will flash GREEN an equal amount of times continuously. 4 Module navigation completed. To return to the MENUS: exit the Module Navigation and redo the Module Navigation Procedure. Failure to exit the Module Navigation will drain vehicle battery. [Y] To save and return to the OPTIS: Press and hold programming button until LED turns solid RED. [Y] LED will flash RED as many times as the current option number continuously. ENGINE STOP 0 0 [X]
MODULE NAVIGATI CHART - OF PAGE OF 7 MODULE NAVIGATI CHART: NOTES [X] MENUS [Y] OPTIS [Z] SETTINGS I II Default settings are listed in bold. Make sure the option is covered on the vehicle before attempting to change the setting. *Vehicle will shutdown when a door is opened. 0 DISARM/UNLOCK BEFORE 0 0 0 RELOCK AFTER 0 0 0 RELOCK AFTER SHUTDOWN 0 0 04 FORCE UNLOCK ALL FIRST PRESS 0 0 05 TAKEOVER 0 ENABLE 0 DISABLE* 0 45 SEC 06 SECURE TAKEOVER DELAY 0 90 SEC 0 0 MIN 04 04 MIN 07 N/A 0 N/A 0 CFIGURATI 0 0 MIN 0 05 MIN 0 0 MIN 08 MODULE RUN TIME 04 5 MIN 05 5 MIN 06 0 MIN 07 5 MIN 08 5 MIN 0 0 SEC 0 05 SEC 0 08 SEC 09 WAIT TO DELAY 04 0 SEC 05 5 SEC 06 0 SEC 07 5 SEC 08 0 SEC 0- N/A 0 N/A 0-07 Technical Support only 0 N/A 0 N/A
REMOTE ER ERROR CODES - OF PAGE OF 7 REMOTE ER ERROR CODES: NOTES [X] NUMBER OF PARKING LIGHT FLASHES DIAGNOSTIC I II WARNING: The following applies only when the parking lights are connected and supported by the system. After a remote starter failure, the parking lights will flash [X] number times to indicate an error code. See table. 0 Foot brake is. 04 Hood is open. 05 Engine tach signal is lost. 06 System is in Valet Mode. 07 Vehicle is moving (VSS). 08 Glow plug timeout error.
MODULE DIAGNOSTICS - OF PAGE 4 OF 7 TEST MODULE LED STATUS DIAGNOSTIC I II III DURING PROGRAMMING DURING REMOTE WITH IGNITI Flashing RED Solid RED Flashing GREEN Solid GREEN then Flashing RED Solid RED Flashing GREEN Solid GREEN then Flashing RED Solid RED Flashing GREEN Solid GREEN then Missing/wrong information from firmware or vehicle. Module waiting for more vehicle information. Additional steps required to complete module programming. Module correctly programmed. No activity or module already programmed. Module incorrectly programmed. Module incorrectly programmed. Module correctly programmed and operational. Reset in progress. Invalid ground when running status from remote starter. Module incorrectly programmed or connected. Module not programmed. Waiting for more vehicle information. False ground when running status from remote starter. Reset in progress. Module at rest and ready for a remote start sequence.
MODULE RESET PROCEDURE - OF PAGE 5 OF 7 0 Disconnect all connectors from module except the BLACK 4-PIN connector. 07 Reconnect all connectors. 0 Disconnect the BLACK 4-PIN connector. 08 Repeat programming procedure. 0 PRESS AND HOLD programming button while connecting the BLACK 4-PIN connector. Failure to follow procedure may result with a DTC or a CHECK ENGINE error message. 04 Wait, LED will flash RED. RELEASE programming button. 05 LED will turn RED for seconds. 06 Module RESET completed.
TAKEOVER PROCEDURE - OF PAGE 6 OF 7 All vehicle doors must be closed and locked prior to remote start sequence. 06 Press and release BRAKE pedal. 0 Time restriction. Complete steps to 6 within 45 seconds. 07 Take over procedure completed. 0 Press unlock on OEM or aftermarket remote. Failure to follow procedure will result in vehicle engine shutdown. 0 Open driver door and enter vehicle. 04 Close driver door. 05 Turn key to position.
INSTALLATI CHECKLIST - OF PAGE 7 OF 7 CHECKLIST WARNING: Vehicle engine will start many times. Test in a well ventilated area. Close all vehicle doors, hood and trunk. Press LOCK button three times [x] rapidly on the OEM keyfob to remote start vehicle. Question : Does the vehicle remote start? YES: Go to next step. NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call technical support, if the problem persists. 4 Press LOCK button three times [x] rapidly on the OEM keyfob to shut down vehicle. Question : Does the vehicle shut down? YES: Go to next step. NO: Repeat step. If the problem persists, press on the brake pedal once [x] to shut down the vehicle and call technical support. 5 RAP Shutdown test Question : Did the radio, interior controls, and headlights turn off within 60 seconds after remote start shutdown? YES: Go to next step. NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support, if the problem persists. 6 Open hood. 7 If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step. 8 Press LOCK button three times [x] rapidly on the OEM keyfob to remote start vehicle. Question 4: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 9 Close hood. 0 Enter vehicle and close the doors. Press LOCK button three times [x] rapidly on the OEM keyfob to remote start vehicle. Wait for the vehicle to start. Press brake pedal. Question 5: Does the vehicle shut down? YES: Go to next step. NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if applicable, and call technical support. 4 Exit vehicle. 5 Installation checklist completed.