Counting every Drop SPARE PARTS & TOOLS For maximum operational reliability SAVE TIME AND MONEY WITH FAURE HERMAN SPARE PARTS AND TOOLS Faure Herman equipment is engineered for high reliability and performance. To assure the best performance of your meter regular maintenance and recalibration is recommended. Faure Herman offers you a wide range of calibrated cartridge, bearing kit, tools and other spare parts in order to keep your business running. Consider ordering your spare parts today will help reduce your downtime, maintenance time and cost. Contact your local Faure Herman representative to optimize your inventory maintenance schedule. CALIBRATED CARTRIDGE FOR TZN AND TLM Faure Herman TZN and TLM meters utilize a removable calibrated cartridge inserted into the body. The Faure Herman cartridge principle offers: Easy replacement of internals less than 5 min Limited downtime / interruption of service Time and money savings Interchangeable spare cartridges, calibrated with same conditions, for easy maintenance Ability to send only the cartridge for repair/calibration at Faure Herman laboratory Ability to rebuild/refurbish meters with just a few parts A spare cartridge assures you are never more than a few minutes away from having your meter operational again. 1
HELICAL TURBINE METER TZN : calibrated cartridge ordering information 1 2 3 4 5 6 7 8 9 10 11 SEM_TZN STD - J1 - T - H - 1 - B - D - D - 03-1 - / CUS- CUS STD- Standard A- Acids 4 : Fluid type B- Industrial Alcohol C- Demineralized Water D- Sea Water E- Water G- LPG H- Hydrocarbons L- Beverages S- Solvents 1 : Type 2 : Model / Size A1-16-012 / 1/2" E3-40-15 / 1"1/2 K2-200-1000 / 8" A2-16-025 / 1/2" E4-40-20 / 1"1/2 K3-200-1200 / 8" B1-20-05 / 3/4" E5-40-40 / 1"1/2 L1-250-1200 / 10" B2-20-1 / 3/4" F1-50-30 / 2" L2-250-2000 / 10" C1-25-2 / 1" F2-50-50 / 2" M1-300-2400 / 12" C2-25-3 / 1" F3-50-70 / 2" M2-300-3000 / 12" C3-25-5 / 1" G1-80-70 / 3" N1-350-3500 / 14" C4-25-10 / 1" G2-80-110 / 3" P1-400-4000 / 16" D1-32-8 / 1"1/4 G3-80-150 / 3" P2-400-4500 / 16" D2-32-12 / 1"1/4 H1-100-200 / 4" Q1-450-4800 / 18" D3-32-15 / 1"1/4 H2-100-300 / 4" Q2-450-5500 / 18" D4-32-20 / 1"1/4 J1-150-400 / 6" R1-500-6000 / 20" E1-40-8 / 1"1/2 J2-150-600 / 6" E2-40-12 / 1"1/2 K1-200-800 / 8" 3 : Rotor / Internal Material A- Aluminium / SS T- Titanium / SS V- Titanium / Titanium 5 : Nb of product(s) 1-1 product 2-2 products 3-3 products 4-4 products 6 : Nb of points x Run(s) A- 6x1 B- 6x3 C- 6x5 D- 10x1 E- 10x3 F- 10x5 G- 8x5 H- 6x2 7 & 8 : Viscosity in cst (min/max) A- 0.6 J- 5 < V < 10 B- 1 K- 10 < V < 30 C- 1.6 L- 30 < V < 50 D- 5 M- 50 < V < 100 E- < 0.6 N- 100 < V < 200 F- 0.6 < V < 1 P- 200 < V < 350 G- 1 < V < 1.6 Q- 350 < V H- 1.6 < V < 5 9 : Linearity / Repeatability 01- ± 0.15 % / without 12- ± 0.30 % / 0.04 % 02- ± 0.15 % / 0.02 % 13- ± 0.50 % / without 03- ± 0.15 % / 0.04 % 14- ± 0.50 % / 0.02 % 04- ± 0.20 % / without 15- ± 0.50 % / 0.04 % 05- ± 0.20 % / 0.02 % 16- ± 1.00 % / without 06- ± 0.20 % / 0.04 % 17- ± 1.00 % / 0.02 % 07- ± 0.25 % / without 18- ± 1.00 % / 0.04 % 08- ± 0.25 % / 0.02 % 19- ± 0.1 % / without 09- ± 0.25 % / 0.04 % 20- ± 0.1 % / 0.02 % 10- ± 0.30 % / without 21- ± 0.1 % / 0.04 % 11- ± 0.30 % / 0.02 % xx- Other 10 : Calibration method 1- Single K factor 2- Multiple K factors 3- Viscosity Indexing 4- Master Meter 11 : Turndown ratio Defined by Faure Herman based on application 2
HELICAL TURBINE METER TLM : calibrated cartridge ordering information 1 2 3 4 5 6 7 8 9 SEM_TLM A5 - A - H - 2 - B - A - D - 06 - / 1 : Model / Size A1-3-30 / 3" A2-3-50 / 3" A3-3-70 / 3" A4-3-110 / 3" A5-3-150 / 3" B3-4-70 / 4" B4-4-110 / 4" B5-4-150 / 4" B6-4-200 / 4" B7-4-300 / 4" 2 : Rotor / Internal Material A- Aluminium B- Titanium 3 : Fluid type A- Acids B- Industrial Alcohol C- Demineralized Water D- Sea Water E- Water G- LPG H- Hydrocarbons L- Beverages S- Solvents 4 : Nb of product(s) 1-1 product 2-2 products 3-3 products 5 : Nb of points x Run(s) A- 6x1 B- 6x3 6 & 7 : Viscosity in cst (min/max) A- 0.6 F- 0.6 < V < 1 B- 1 G- 1 < V < 1.6 C- 1.6 H- 1.6 < V < 5 D- 5 J- 5 < V < 15 E- < 0.6 X-Other 8 : Linearity / Repeatability 01- ± 0.15 % / without 06- ± 0.25 % / 0.04 % 02- ± 0.15 % / 0.04 % 07- ± 0.30 % / without 03- ± 0.20 % / without 08- ± 0.30 % / 0.04 % 04- ± 0.20 % / 0.04 % xx- Other 05- ± 0.25 % / without 9 : Turndown ratio Defined by Faure Herman based on application 3
MECHANICAL PARTS FOR TURBINE METERS : BEARING KIT Bearing kit for TZN 2" Bearing kit for TZN 3" Bearing kit for TZN CUS Bearing kit for TZN BNAE Bearing kit for TCX Turbine Bearing ref Bearing ref Model Type (Carbide) (Graphite) TZN STD TZN STD 16-xxx (1/2") L00019 L00020 TZN STD 20-xxx (3/4") L00021 L00022 TZN STD 25-xxx (1") L00023 L00024 ZN STD 32-xxx (1" 1/4) L00025 L00026 TZN STD 40-xxx (1" 1/2) L00025 L00026 TZN STD 50-xxx (2") L00003 L00027 TZN STD 80-xxx (3") L00028 L00029 TZN STD 100-xxx (4") L00013 L00005 TZN STD 150-xxx (6") L00014 L00006 TZN STD 200-xxx (8") L00009 L00031 TZN STD 250-xxx (10") L00010 L00032 TZN STD 300-xxx (12") L00015 L00007 TZN STD 350-xxx (14") L00016 L00008 TZN STD 400-xxx (16") L00034 - TZN STD 450-xxx (18") L00018 - TZN CUS TZN CUS 80-xxx (3") 412027 TZN CUS 100-xxx (4") 411893 TZN CUS 150-xxx (6") 411894 TZN CUS 200-xxx (8") 411895 TZN CUS 250-xxx (10") 411896 TZN CUS 300-xxx (12") 411897 TZN CUS 350-xxx (14") 411989 TZN CUS 400-xxx (16") 411990 TZN CUS 450-xxx (18") 411898 TZN BNAE TZN BNAE 16 (1/2") L00019 L00020 TZN BNAE 20 (3/4") L00021 L00022 TZN BNAE 25 (1") L00023 L00024 TZN BNAE 32 (1" 1/4) L00025 L00026 TZN BNAE 50 (2") L00003 L00027 TLM TLM 3-30 / TLM 3-50 (3") L00003 L00027 TLM 3-70 / TLM 3-110 / TLM 3-150 (3") L00028 L00029 TLM 4-70 / TLM 4-110 / TLM 4-150 (4") L00028 L00029 TLM 4-200 / TLM 4-300 (4") L00013 L00005 TCX Gen2 TCX 25-xxx (1") L00056 L00060 TCX 32-xxx (1" 1/4) L00057 L00061 TCX 40-xxx (1" 1/2) L00058 L00062 TCX 50-xxx (2") L00059 L00063 TCX 80-xxx (3") L00036 L00037 TCX 100-xxx (4") L00038 L00039 TCX 150-xxx (6") L00040 L00041 TCX 200-xxx (8") L00042 L00043 TCX 250-xxx (10") L00044 L00045 TCX 300-xxx (12") L00046 L00047 4
ELECTRICAL SPARE PARTS FOR TURBINE METERS Pick-up coils 10-15-10 kit 500431 10-15-10/1 kit 510085 10-15-20 kit 510093 10-15-20/1 kit 510094 200161 (cable 5m) 400229 10-00-55 kit 500004 PC45-25 500886 Pick-up coil 10-15- 10 kit Pick-up coil 200161 Pick-up coil PC45-25 Preamplifiers FH710 Standard 2 wires 500090 FH710 Standard 2 wires sensitive 500094 FH710 Namur 500092 FH710 Namur sensitive 500093 FH710 Open collector 500091 Preamplifier FH710 Enclosure parts* UL/cUL Enclosure kit with FH710 standard 2 wires SS316 413893 UL/cUL Enclosure kit with FH710 Namur sensitive SS316 413974 UL/cUL Enclosure kit with FH710 open collector SS316 413964 ATEX/IECEx Enclosure kit for FH boss SS316 413992 ATEX/IECEx Enclosure kit for 1"NPT FH boss SS316 413993 1"NPT FH boss adapter SS316 407887 1"NPT Thermal extension SS316 411428 *Consult the factory for enclosure compatibility and certification for your material. UL/cUL enclosure kit certified : Class 1 div 1 Group C&D ATEX/IECEx enclosure kit certified : II2G Ex d IIC T6 Gb UL/cUL Enclosure kit ATEX/IECEx Enclosure kit for FH boss 1"NPT FH boss adapter 1 NPT Thermal extension Retaining ring kit L00035 Small TZN boss block 413762 Enclosure cover gasket 200382 Enclosure gasket 400669 5
SPARE PARTS FOR ULTRASONIC METER FH8300/FH8400 transducer 302032 ( 12") or 302033 (>12") FH8500 transducer 1 Mhz (>12") 301718 FH8500 transducer 2,25 Mhz ( 12") 300714 FH8300 Electronic set 510031 FH8400 Electronic set 500905 FH8500 Electronic set 500789 Infrared Remote control F10101 SPECIFIC TOOLS To assemble the parts, some needed specific tools are defined and can be provided. Wrench for enclosure 870054 Tool for coil extraction 870055 Tool for coil assembly 870046 Tool for coil threaded adapter 870045 Tool for PC45-25 coil assembly 413979 FH8500 transducer extractor 302287 6
Tool for threaded cartridge assembly Small size TZN STD and TZN BNAE Tool for TLM cartridge assembly Tool for TZN CUS bearing replacement TZN BNAE 16 (1/2") 870047 TZN BNAE 20 (3/4") 870048 TZN BNAE 25 (1") 870049 TZN BNAE 32 (1" 1/4) 870050 TZN BNAE 50 (2") 870050 TZN BNAE 16 (1/2") 870051 TLM 3-30 / TLM 3-50 (3") 900126 TLM 3-70 / TLM 3-110 / TLM 3-150 (3") TLM 4-70 / TLM 4-110 / TLM 4-150 (4") 900125 900215 TZN CUS 80 (3") 870056 TZN CUS 100 (4") 870057 TZN CUS 150 (6") 870058 TZN CUS 200 (8") 870059 TZN CUS 250 (10") 870060 TZN CUS 300 (12") 870061 TZN CUS 350 (14") 870062 TZN CUS 400 (16") 870063 TZN CUS 450 (18") 870064 TZN CUS 500 (20") 870065 Tool for shaft assembly TZN STD 80 (3") 705982 TZN STD 100 (4") 705982 TZN STD 150 (6") 705983 TZN STD 200 (8") 705984 TZN STD 250 (10") 705985 TZN STD 300 (12") 705986 TZN STD 350 (14") 705987 TZN STD 400 (16") 705988 TZN STD 450 (18") 705989 Tool for TCX threaded crosspiece TCX 80 (3") 870015 TCX 100 (4") 870016 TCX 150 (6") 870017 TCX 200 (8") 870018 TCX 250 (10") 870019 TCX 300 (12") 870020 Other spares are available. Please consult Faure Herman for more information. 7
ONLINE SHOP FOR SPARE PARTS & TOOLS Faure Herman offers you a reliable spare parts & tools service. It s available online at any time - the spare parts you need is just a click way. Log on www.faureherman.com website. CONTACT FAURE HERMAN FOR ALL YOUR METERING NEEDS FAURE HERMAN FAURE HERMAN METER USA FAURE HERMAN DUBAÏ Route de Bonnétable BP 20154 72406 La-Ferté-Bernard Cedex FRANCE 4702 North Sam Houston Parkway West Suite 100 Houston, TX 77086 (U.S.A) Office #738, Building #6EB Dubai Airport Freezone (DAFZA) Dubaï (U.A.E) Tel : +33 (0)2 43 60 28 60 Tel : +1 713 623 0808 Tel : +971 4260 0381 Fax : +33 (0)2 43 60 28 70 Fax : +1 713 623 2332 Fax : +971 4260 0319 E-mail : fhprojects@idexcorp.com E-mail : FHH-Sales@idexcorp.com E-mail : fhsalesme@idexcorp.com www.faureherman.com This document is not contractual, Faure Herman maintains the right to modify certain characteristics without notice. Ref Spare parts & tools 01/2016 ENERGY & FUELS 8