Direct Operated ype Solenoid Operated roportional hrottle Valve EM-G EM-G3 EM-G3-X EMS-2 EMS-2 EM-G4 b X EMS-3 Features hese proportional throttle directional control valves perform spool position feedback control by directly driving the spool with the proportional solenoid and detecting the displacement with the differential transformer. Combining the valve with a pressure compensation valve and the dedicated driver achieves highly accurate proportional flow rate control. Highly accurate proportional flow rate control with meter-in control at port or meter-out control at port can be realized by stacking the EMS valves in combination with the dedicated reduction type pressure compensation valve (MGS) under the solenoid valve. Nomenclature Gasket mount type EM - G - F - - 1 2 3 4 5 6 EM - G - F - - 1 2 3 4 5 7 1 Model No. (pplicable fluids: petroleum-based hydraulic oil) EM: Solenoid operated proportional throttle valve EM: ack pressure type solenoid operated proportional throttle valve 2 Connections G: Gasket mount type 3 Nominal diameter 2: ¼ <pplicable only to the model designation EM> 3: ⅜ 4: ½ <pplicable only to the model designation EM> Note: * 1 Specifications with SO.a apply only to nominal diameter 2 (¼). * 2 DIN connector mounting at the left side applies only to nominal diameter 3 ( 3 / 8). * 3 he option code II applies only to EM-G3. 4 Spool type F: Spring offset type ll ports blocked when neutral 5 Design No. (he design No. is subject to change) 6 Option code I No designation: With SO.b (flow ) G: With SO.a (flow ) * 1 : DIN connector mounting position, left side * 2 7 Option code II * 3 No designation: Without ports and X X: With ports and X J ROORION VVES SERVO VVES Stacking type EMS - - - 1 2 3 4 5 6 1 Model No. EMS: Stacking type solenoid operated proportional throttle valve 2 Nominal diameter 2: ¼ 3: ⅜ 3 Control port : ort * 4 : ort Note: * 4 pplicable only to nominal diameter 2 (¼) J-21 4 Design No. (he design No. is subject to change) : Nominal diameter 3 (⅜) 3: Nominal diameter 2 (¼) 5 DIN connector mounting position * 4 No designation: ottom : Right : op C: eft 6 Differential transformer connector mounting position * 4 No designation: ottom Q: Right R: op S: eft
Specifications Model code Nominal diameter Maximum operating pressure Ma {kgf/cm 2 } pplicable driver model code Rated flow port permissible rate * 5 back pressure /min Ma {kgf/cm 2 } Hysteresis, resolution, repeatability Coil resistance ( C) Ω Current at start of flow (Nominal) m Current at rated flow (Nominal) m EM -G2-F- ¼ 2.5 { } EM -G3-F- ⅜ 26 3 7 5 EM-G3-F- ⅜ 21 {2} No greater than 21 {2} 1% of rated input EM-G4-F- ½ 13 voltage 13 5 154 EMS-2-3 ¼ 2.5 { } 26 3 7 EMS-3 - ⅜ 16 {16} 5 Note: * 5 he rated flow rate indicates the values when the valve is used in combination with a pressure compensation valve (differential pressure:.6 Ma {6 kgf/cm 2 }) Valve model code Model code pplicable driver ower supply voltage EM-G, EM-G3, EMS- KF-5- C,, 2 V EM-G4 KFH-5- (Common for 5 and 6 Hz) Sub-plate model code he sub-plate is not provided with the valve. Order it separately as required by specifying the model code given in the table below. Model code Nominal diameter Connection port diameter Mass kg JS-1M2 Rc¼.64 ¼ JS-2M3 Rc⅜ 2.3 ccessories Model No. Hexagon socket head cap bolt Number ightening torque N m {kgf cm} EM-G2 M5 45 4 5 to 8 { 5 to 8} EM()-G3 M6 35 4 to 13 { to 13} EM-G4 M6 5 2 to 13 { to 13} M 55 4 59 to 62 {59 to 6} JS-3M Rc⅜ 2.5 ⅜ JS-3M4 Rc½ 2.2 Refer to age S-8 for the dimensions of the sub-plate. Handling Directly connect the tank and drain piping to the tank without merging it with other tank piping. Do not touch the zero adjusting screw of the differential transformer since it is factory adjusted. Use this valve in combination with a pressure compensation valve. Order a pressure compensation valve separately by referring to the table below as necessary. Model No. EM-G EM-G3 EM-G4 ypass type pressure compensation valve MUV126S MU126N-358 MUV166S MU166N-347 MU12 N-561 Reduction type pressure compensation valve MDM126N MDM166N EMS-2 MGS-2-- (Stacking type) EMS-2 MGS-2-- (Stacking type) EMS-3 MGS-3-- (Stacking type) J-22
erformance curves (viscosity: 32 mm 2 /s {cst}) Input voltage - Flow rate characteristics EM-G2 EM()-G3 EM-G4 3 6 14 5 1 Flow rate (/min) 15 Flow rate (/min) 4 3 Flow rate (/min) 8 6 4 5 1 2 3 4 5 EMS-2() 3 1 2 3 4 5 EMS-3 6 1 2 3 4 5 Flow rate (/min) 15 5 1 2 3 4 5 Frequency response characteristics EM -(G)2 Flow rate (/min) 5 4 3 1 2 3 4 5 EM -(G)3 J ROORION VVES SERVO VVES Flow rate fluctuation: 12 ± 1. /min Flow rate fluctuation: ± 2.5 /min 3 45 3 45 Gain (d) 6 9 12 Gain hase 9 135 18 hase (deg) Gain (d) 6 9 Gain hase 9 135 hase (deg).1.5 1 5 5 Frequency (Hz) EM-G4 Flow rate fluctuation: 65 ± 5 /min 12 18.1.5 1 5 5 Frequency (Hz) 4 Gain (d) 2 Gain 2 4 6 hase 8 12.1 1 5 34 5 Frequency (Hz) 3 6 9 1 15 18 hase (deg) J-23
External dimension diagram EM-G2 Hirschmann: GDM11 Connector for differential transformer SNS-165CF (from Sanwa Denki Kogyo) 93 81.5 4-φ9.5 4-φ5.3 ir bleeding screw Socket for hex key: 2.5 37.5 7 49 15 63 4-φ7 4-φ12 4.5 3.2 21.5 12.7 2.75 5.1 15.5.9 31 31.75 8.5 16.5 9.5 ISO 441-3-2--5 63 Option code I: G 4-φ5.3 EM-G3 Connector for differential transformer SNS-165CF (from Sanwa Denki Kogyo) Hirschmann: GDM11 4-φ14.5 4-φ6.6 ir bleeding screw Socket for hex key: 2.5 36 (64.5) 7 15 92 5-φ11 5-φ16 277 16.5 9.5 7 Option code I: 6.4 21.4 32.5 46 12 7 16.7 27 37.3 5.8 54 92 3.2 19 4-φ6.6 ISO 441-5-4--5 J-24
External dimension diagram EM-G3 8 96.5 Hirschmann: GDM11 4-φ14.5 4-φ6.6 Connector for differential transformer SNS-165CF (from Sanwa Denki Kogyo) ir bleeding screw Socket for hex key: 2.5 122 26.5 4 79 5-φ11 88 5-φ15.57 268 16.5 9.5 7 EM-G4 4-φ17.5 4-φ11 2-φ11 2-φ6.6 16.7 27 37.3 5.8 54 61.9 88 3.2 17 Hirschmann: GDM11 6.3 11.1 12 21.4 32.5 46 7 Option code II: X ISO 441-5-5--5 ir bleeding screw Socket for hex key: 2.5 X 11.1 65.5 7.9 34.5 Connector for differential transformer SNS-165CF (from Sanwa Denki Kogyo) 118.5 J 33 ROORION VVES SERVO VVES 36.5 74 2-φ12 4-φ26 129.5 328.5 189.5 9.5 93 129.5 1.6 14 14.3 1.6 4-φ11 34.9 55.6 57.2 69.9 71.5 11 93 18.3 34.1 5 65.9 76.6 88.1 J-
External dimension diagram EMS-2() 63 4.5 11 3.2 21.5 12.7 1.5 11 15.5.9 31 31.75 21.5 R ir bleeding screw Socket for hex key: 2.5 With EMS-2 243 9.5 16.5 63.75 5.1 8.5 With EMS-2 8.5 S C Q 29.3 6 111.3 4-φ5.4 4-φ7 4-φ12 Guide to the DIN connector and differential transformer option codes Connector for Hirschmann: GDM11 differential transformer SNS-165CF (from Sanwa Denki Kogyo).75 5.1 1.5 12.7 21.5 3.2 4.5 11 63 With EMS-2 9.5 8.5 15.5.9 31 31.75 With EMS-2 ISO 441-3-2--5 EMS-3 3 2 64 54 5.8 37.3 27 16.7 3.2 6.3 21.4 32.5 12 46 7 ISO 441-5-4--5 Hirschmann: GDM11 Connector for differential transformer SNS-165CF (from Sanwa Denki Kogyo) 95.5 84 ir bleeding screw Socket for hex key: 2.5 9.5 27.5 55 4-φ6.5 4-φ11 5-φ16 2 282 16.5 9.5 31 7 J-26
Sectional structural diagram EM-G2 12 11 7 6 4 3 1 13 2 5 14 8 9 art No. Name Quantity art specifications 13 O-ring 4 JIS 241 1 9 14 O-ring 2 S568-121 (NR, Hs9) EM-G3 J 7 6 4 3 1 13 2 5 14 8 9 11 12 art No. Name Quantity art specifications 13 O-ring 5 JIS 241 1 12 14 O-ring 2 S568-121 (NR, Hs9) ROORION VVES SERVO VVES EM-G3 9 11 6 15 5 4 14 3 1 12 2 13 7 8 art No. Name Quantity EM-G3-F- art specifications EM-G3-F--X 12 O-ring 5 S568-14 (NR, Hs9) S568-14 (NR, Hs9) 13 O-ring 1 2 JIS 241 1 9 JIS 241 1 9 14 O-ring 1 S568-8 (NR, Hs9) 15 O-ring 2 S568-121 (NR, Hs9) S568-121 (NR, Hs9) J-27
Sectional structural diagram EM-G4 7 8 11 13 12 16 5 6 4 3 14 1 2 15 17 9 art No. Name Quantity art specifications 14 O-ring 4 JIS 241 1 22 15 O-ring 2 JIS 241 1 9 16 O-ring 1 S568-21 (NR, Hs9) 17 O-ring 1 JIS 241 1 44 EMS-2() 8 7 14 11 4 3 12 2 13 1 5 6 9 art specifications art No. Name Quantity EMS-2-3 EMS-2-3 12 O-ring 4 JIS 241 1 9 JIS 241 1 9 13 O-ring 1 JIS 241 1 7 14 O-ring 2 S568-121 (NR, Hs9) S568-121 (NR, Hs9) EMS-3 9 11 6 5 4 3 2 12 1 13 7 8 art No. Name Quantity art specifications 12 O-ring 5 S568-14 (NR, Hs9) 13 O-ring 2 S568-121 (NR, Hs9) J-28