SERVICE MANUAL FRYMASTER BIPH4/MPH4 SERIES ELECTRIC FRYER This equipment chapter is to be installed in the Fryer Section of the Equipment Manual. FOR YOUR SAFETY Do Not Store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. MANUFACTURED BY P.O. BOX 000 SHREVEPORT, LOUISIANA 3-000 PHONE: -38-8- TOLL FREE: -800--833-800-4 FRYER FAX: -38-88-00 TABLE OF CONTENTS WARRANTY STATEMENT... Page i SERVICE PROCEDURES... Page -. General... Page -. Replacing a Computer...Page -.3 Replacing Component Box Components... Page -.4 Replacing a Temperature Probe or High-Limit Thermostat...Page -3. Replacing a Heating Element... Page -4. Replacing Contactor Box Components... Page -. Replacing a Frypot...Page -.8 Built-in Filtration System Service Procedures... Page -9.9 Interface Board Diagnostic Charts... Page -3.0 Wiring Diagrams... Page -4 PARTS LIST... Page - Frymaster L.L.C., 800 Line Avenue 0 P.O. Box 000, Shreveport, Louisiana 3-000 PHONE 38-8- FAX 38-9-3 PRINTED IN THE UNITED STATES SERVICE HOTLINE -800-4-FRYER MAY 00 *890*
NOTICE IF, DURING THE WARRANTY PERIOD, THE CUSTOMER USES A PART FOR THIS ENODIS EQUIPMENT OTHER THAN AN UNMODIFIED NEW OR RECYCLED PART PURCHASED DIRECTLY FROM FRYMASTER/DEAN, OR ANY OF ITS AUTHORIZED SERVICE CENTERS, AND/OR THE PART BEING USED IS MODIFIED FROM ITS ORIGINAL CONFIGURATION, THIS WARRANTY WILL BE VOID. FURTHER, FRYMASTER/DEAN AND ITS AFFILIATES WILL NOT BE LIABLE FOR ANY CLAIMS, DAMAGES OR EXPENSES INCURRED BY THE CUSTOMER WHICH ARISE DIRECTLY OR INDIRECTLY, IN WHOLE OR IN PART, DUE TO THE INSTALLATION OF ANY MODIFIED PART AND/OR PART RECEIVED FROM AN UNAUTHORIZED SERVICE CENTER. NOTICE This appliance is intended for professional use only and is to be operated by qualified personnel only. A Frymaster/Dean Factory Authorized Service Center (FASC) or other qualified professional should perform installation, maintenance, and repairs. Installation, maintenance, or repairs by unqualified personnel may void the manufacturer s warranty. See Chapter of this manual for definitions of qualified personnel. NOTICE This equipment must be installed in accordance with the appropriate national and local codes of the country and/or region in which the appliance is installed. See NATIONAL CODE REQUIREMENTS in Chapter of this manual for specifics. NOTICE TO U.S. CUSTOMERS This equipment is to be installed in compliance with the basic plumbing code of the Building Officials and Code Administrators International, Inc. (BOCA) and the Food Service Sanitation Manual of the U.S. Food and Drug Administration. NOTICE Drawings and photos used in this manual are intended to illustrate operational, cleaning and technical procedures and may not conform to onsite management operational procedures. NOTICE TO OWNERS OF UNITS EQUIPPED WITH COMPUTERS U.S. This device complies with Part of the FCC rules. Operation is subject to the following two conditions: ) This device may not cause harmful interference, and ) This device must accept any interference received, including interference that may cause undesired operation. While this device is a verified Class A device, it has been shown to meet the Class B limits. CANADA This digital apparatus does not exceed the Class A or B limits for radio noise emissions as set out by the ICES- 003 standard of the Canadian Department of Communications. Cet appareil numerique n emet pas de bruits radioelectriques depassany les limites de classe A et B prescrites dans la norme NMB-003 edictee par le Ministre des Communcations du Canada. DANGER Improper installation, adjustment, maintenance or service, and unauthorized alterations or modifications can cause property damage, injury, or death. Read the installation, operating, and service instructions thoroughly before installing or servicing this equipment. DANGER The front ledge of this appliance is not a step! Do not stand on the appliance. Serious injury can result from slips or contact with the hot cooking oil/shortening. DANGER Do not store or use gasoline or other flammable liquids or vapors in the vicinity of this or any other appliance. DANGER The crumb tray in fryers equipped with a filter system must be emptied into a fireproof container at the end of frying operations each day. Some food particles can spontaneously combust if left soaking in certain shortening material. WARNING Do not bang fry baskets or other utensils on the fryer s joiner strip. The strip is present to seal the joint between the fry vessels. Banging fry baskets on the strip to dislodge shortening will distort the strip, adversely affecting its fit. It is designed for a tight fit and should only be removed for cleaning.
WARRANTY STATEMENT Frymaster, L.L.C. makes the following limited warranties to the original purchaser only for this equipment and replacement parts: A. WARRANTY PROVISIONS - FRYERS. Frymaster L.L.C. warrants all components against defects in material and workmanship for a period of one year.. All parts, with the exception of the frypot, heating elements and fuses, are warranted for one year after installation date of fryer. 3. If any parts, except fuses, become defective during the first year after installation date, Frymaster will also pay straight-time labor costs to replace the part, plus up to 00 miles/0 km of travel (0 miles/80 km each way). B. WARRANTY PROVISIONS - FRYPOTS If a frypot develops a leak within seven years after installation, Frymaster will, at its option, either replace the entire battery or replace the frypot, allowing up to the maximum time per the Frymaster time allowance chart hours of straight-time labor plus up to 00 miles/0 km of travel (0 miles/80 km each way) to change the frypot. C. WARRANTY PROVISIONS - HEATING ELEMENTS. Frymaster L.L.C. warrants the heating elements against defective material or workmanship for a period of three years from the original installation date, parts only.. This warranty does not cover ancillary components, including the hi-limit, temperature probe, and contactors. D. WARRANTY PROVISIONS - COOKING COMPUTER. Frymaster L.L.C. warrants the M-000 Cooking Computer against defective material or workmanship for a period of one year from the original installation date, parts and labor. Replacements for defective units during the second year will fall under warranty; however, labor will not. Replacements are available during the third year at a reduced rate.. Replacement M-000 Cooking Computers will be warranted for the first and second years only. Replacements are available during the third year at a reduced rate. When a computer is replaced under warranty, the replaced computer carries the remaining original warranty only. 3. During this warranty period, Frymaster will, at its option, repair or replace defective cooking computer returned with new and functionally operative units. 4. For replacement of defective computers under warranty, call your local Frymaster Factory Authorized Service Center. All computers replaced under the Frymaster exchange program are covered by a one-year (parts only) warranty. i
E. PARTS RETURN All defective in-warranty parts must be returned to a Frymaster Authorized Factory Service Center within 0 days for credit. After 0 days, no credit will be allowed. F. WARRANTY EXCLUSIONS This warranty does not cover equipment that has been damaged due to misuse, abuse, alteration, or accident such as: improper or unauthorized repair (including any frypot which is welded in the field); failure to follow proper installation instructions and/or scheduled maintenance procedures as prescribed in your MRC cards. Proof of scheduled maintenance is required to maintain the warranty; improper maintenance; damage in shipment; abnormal use; removal, alteration, or obliteration of either the rating plate or the date code on the heating elements; operating the frypot without shortening or other liquid in the frypot; no fryer will be warranted under the seven-year program for which a proper start-up form has not been received. This warranty also does not cover: transportation or travel over 00 miles/0 km (0 miles/80 km each way), or travel over two hours; overtime or holiday charges; consequential damages (the cost of repairing or replacing other property which is damaged), loss of time, profits, use or any other incidental damages of any kind. There are no implied warranties of merchantability or fitness for any particular use or purpose. ii
BIPH4/MPH4 SERIES ELECTRIC FRYERS CHAPTER : SERVICE PROCEDURES. General Before performing any maintenance on your Frymaster fryer, disconnect the fryer from the electrical power supply. To ensure the safe and efficient operation of the fryer and hood, the electrical plug for the 0-volt line, which powers the hood, must be fully engaged and locked in its pin and sleeve socket. When electrical wires are disconnected, it is recommended that they be marked in such a way as to facilitate re-assembly.. Replacing a Computer. Before removing controllers from Euro-look models (round top-cap and drains), slide the metal bezel up to release the bottom tabs; then, remove it.. Remove the two screws from the upper corners of the control panel. The control panel is hinged at the bottom and will swing open from the top. Remove screws in upper corners of control panel and swing control panel down. 3. Unplug the wiring harness from the connector on the back of the computer and disconnect the grounding wire from terminal adjacent to the connector. Remove the control panel assembly by lifting it from the hinged slots in the control panel frame. -Pin Connector Ground Wire Terminal -
4. Remove the controller from the control panel assembly and install the replacement computer. Reinstall the control panel assembly by reversing steps and..3 Replacing Component Box Components. Remove the two screws from the upper corners of the control panel and allow the control panel to swing down (see steps and of section. on preceding page).. Unplug the wiring harness from the -pin connector on the interface board and disconnect the grounding wire from terminal adjacent to the -pin connector on the back of the controller. Remove the control panel assembly by lifting it from the hinge slots in the control panel frame. 3. Disconnect the wiring from the component to be replaced, being sure to make a note of where each wire was connected. NOTE: If replacing the interface board, connectors J and J must also be disconnected from the -pin connectors on the rear of the component box, directly behind the interface board. 4. Dismount the component to be replaced and install the new component, being sure that any required spacers, insulation, washers, etc. are in place. NOTE: If more room to work is required, the control panel frame and top cap assembly may be removed by removing the hex head screws that secure it to the fryer cabinet (see illustration below). If this option is chosen, all control panel assemblies must be removed per steps and above. The cover plate on the lower front of the component box may also be removed if desired. Removing the component box itself from the fryer is not recommended due to the difficulty involved in disconnecting and reconnecting the oil-return valve rods, which pass through openings in the component box. Remove these three screws at each end. Remove these two screws from the center supports. Removing the Control Panel Frame and Top Cap Assembly -
. Reconnect the wiring disconnected in step 3, referring to your notes and the wiring diagrams on the fryer door to ensure that the connections are properly made. Also, verify that no other wiring was disconnected accidentally during the replacement process.. Reverse steps and to complete the replacement and return the fryer to service..4 Replacing a Temperature Probe or High-Limit Thermostat. Remove the filter pan and lid from the unit. Drain the frypots into an oil disposal unit (MSDU) or other appropriate metal container. DANGER DO NOT drain more than one full frypot or two split frypots into the MSDU at one time.. Disconnect the fryer from the electrical power supply and reposition it to gain access to the rear of the fryer. 3. Remove the tilt housing and back panels from the fryer. The tilt housing must be removed first in order to remove the upper back panel. To remove the tilt housing, raise the elements and allow them to rest on the basket support racks as shown in the photo below. Next, remove the hex head screws from the rear edge of the housing. The housing can then be lifted straight up and off the fryer. Lift up on the upper back panel to disengage the tabs on its upper corners from the cutouts in the fryer frame. 4. Disconnect the wire harness at connector C and, using a pin pusher, disconnect the probe leads or high-limit leads from the connector.. If replacing a temperature probe, remove the screw securing the probe bracket to the element and slide the bracket off the element and probe. Pull the probe out of the tilt housing assembly, install the replacement probe, and reattach the element bracket. Secure the upper portion of the probe with a replacement metal wire tie. -3
Probe Leads Metal Wire Tie Probe Bracket If replacing a high-limit thermostat, unscrew the thermostat to be replaced. Apply Loctite PST or equivalent sealant to the threads of the replacement and screw it securely into the frypot.. If a temperature probe was replaced, insert the probe leads into the connector (see left illustration below). For full-vat units or the right half of a dual-vat unit, the red lead goes into position and the white into position. For the left half of a dual-vat unit, the red lead goes into position and the white into position 3. NOTE: Right and left refer to the fryer as viewed from the rear. 3 Rib marks Position 0 4 Probe Lead Positions High-Limit Lead Positions If a high-limit thermostat was replaced, insert the leads into the connector (see right illustration above). For full-vat units or the right half of a dual-vat unit, the leads go into positions 4 and of the connector. For the left half of a dual-vat unit, the leads go into positions 0 and. In either case, polarity does not matter. NOTE: Right and left refer to the fryer as viewed from the rear.. Reinstall the back panels and tilt housing to complete the installation, then reverse steps and to return the fryer to service.. Replacing a Heating Element. Perform steps -3 of section.4, Replacing a Temperature Probe.. On dual-vat fryers, and on full-vat fryers where the temperature probe is attached to the element being replaced, disconnect the wire harness containing the probe wiring (connector C). Using a pin pusher, disconnect the probe wires from the connector. -4
3. On the front of the contactor box, disconnect the -pin connector for the left element (as viewed from the front of the fryer) or the 9-pin connector for the right element and pull the harness out through the rear of the fryer. Press in on the tabs on each side of the connector while pulling outward on the free end to extend the connector and release the element leads (see photo below). Pull the leads out of the connector and out of the plastic wire loom. 4. Raise the element to the full up position and disconnect the element springs.. Remove the nuts and machine screws that secure the element to the tilt plate assembly and pull the element out of the frypot. NOTE: Full-vat elements consist of two dual-vat elements clamped together. For full-vat units, remove the element clamps before removing the nuts and machine screws that secure the element to the tilt plate assembly.. If applicable, recover the probe bracket and probe from the element being replaced and install them on the replacement element, then install the replacement element in the frypot, securing it with the nuts and screws removed in Step.. Route the element leads through the wire loom to prevent chafing and press the pins into the connector in accordance with the diagram below, then close the connector to lock the leads in place. Pip marks Position 3 3 4 4 9 8 L L 4L 3L L L R R 4R 3R R R 8. Insert the element connector into the receptacle on the front of the contactor box, ensuring that the latches lock. 9. If disconnected in step, insert the temperature probe leads into the wiring harness connector (see illustration below). For full-vat units or the right half of a dual-vat unit, the red lead goes -
into position and the white into position. For the left half of a dual-vat unit, the red lead goes into position and the white into position 3. NOTE: Right and left refer to the fryer as viewed from the rear. 3 Rib marks Position 0. If disconnected in step, reconnect connector C of the wiring harness.. Reconnect the element springs and lower the element back down onto the basket rack.. Reinstall the tilt housing and back panels, reposition the fryer under the exhaust hood, and reconnect it to the electrical power supply.. Replacing Contactor Box Components. Remove the filter pan and lid from the unit. Drain the frypots into an oil disposal unit (MSDU) or other appropriate metal container. DANGER DO NOT drain more than one full frypot or two split frypots into the MSDU at one time.. Disconnect the fryer from the electrical power supply. 3. Unplug the wiring harnesses from the contactor box to be serviced. 4. Remove the two screws that secure the box in place. NOTE: If you remove the screws from both boxes at the same time, the boxes will jam against each other and neither can be removed. Remove these screws to dismount the left contactor box. The right contactor box is secured in a similar manner. -
. Carefully lower the box to the floor and pull it out the front of the fryer. Remove the top cover to access contactors and other components.. After performing necessary service, reverse steps - to return the fryer to operation.. Replacing a Frypot. Remove the filter pan and lid from the unit. Drain the frypots into an oil disposal unit (MSDU) or other appropriate metal container. DANGER DO NOT drain more than one full frypot or two split frypots into the MSDU at one time.. Disconnect the fryer from the electrical power supply and reposition it to gain access to both the front and rear. 3. On Euro-look models, slide the metal bezel up to release the bottom tabs; then, remove it. 4. On all models, remove the two screws from the upper corners of the control panels and allow them to swing down (see illustration and photo on page -).. Unplug the wiring harnesses and ground wires from the backs of the controllers. Remove the controllers by lifting them from the hinge slots in the control panel frame.. Remove the tilt housing and back panels from the fryer. The tilt housing must be removed first in order to remove the upper back panel. To remove the tilt housing, raise the elements and allow them to rest on the basket support racks (see photo on page -3). Next, remove the hex head screws from the rear edge of the housing. The housing can then be lifted straight up and off the fryer. Lift up on the upper back panel to disengage the tabs on its upper corners from the cutouts in the fryer frame.. Dismount the top cap by removing the hex head screws at each end that secure it to the control panel frame. 8. Remove the hex head screw that secures the front of the frypot to the cabinet cross brace. 9. Remove the top-connecting strip that covers the joint with the adjacent frypot. 0. On standard models, unscrew the Teflon vent/vacuum-breaker tube fitting, open the drain tube cleanout covers, unscrew the retainer nuts from the drain valve nipples, and remove the tube assembly from the fryer. On Euro-look models, unscrew the Teflon vent/vacuum-breaker tube fitting, unscrew the nut located on the front of each section of drain tube, and remove the tube assembly from the fryer.. Remove the covers from the drain safety switch(es) and disconnect the switch wiring at the switch(es). -
. At the rear of the fryer, unplug the C connector and, using a pin pusher, disconnect the highlimit thermostat leads. 3. Disconnect the oil return flexline(s) at the frypot end(s). 4. Raise the elements to the full up position and disconnect the element springs.. Remove the machine screws and nuts that secure the tilt plate and element assembly to the frypot. Carefully lift the tilt plate and element assembly from the frypot and secure it to the cross brace on the rear of the fryer with wire ties or tape.. Carefully lift the frypot from the fryer and place it upside down on a stable work surface.. Recover the drain valve(s), oil return flexline connection fitting(s), and high-limit thermostat(s) from the frypot. Apply Loctite PST or equivalent sealant to the threads of the recovered parts and install them in the replacement frypot. 8. Carefully lower the replacement frypot into the fryer. Reinstall the hex head screw removed in step to attach the frypot to the fryer. 9. Position the tilt housing and element assembly in the frypot and reinstall the machine screws and nuts removed in step 4. 0. Reconnect the oil return flexlines to the frypot, and replace aluminum tape, if necessary, to secure heater strips to the flexlines.. Insert the high-limit thermostat leads disconnected in step (see illustration on page -4 for pin positions).. Reconnect the drain safety switch wiring to the switch(es) in accordance with the diagram below then reinstall the switch covers. TO SWITCHES ON ADJACENT FRYER C RED Left Dual-Vat Oil Return Switch C RED 0C RED C RED 0C RED C RED Right Dual-Vat or Full-Vat Oil Return Switch 3. Reinstall the drain tube assembly. 4. Reinstall the tilt housing and back panels, top cap, and top connecting strip.. Reinstall controllers in the control panel frame and reconnect the wiring harnesses and ground wires.. Reposition the fryer under the exhaust hood and reconnect it to the electrical power supply. -8
.8 Built-in Filtration System Service Procedures.8. Filtration System Problem Resolution One of the most common causes of filtration problems is placing the filter paper on the bottom of the filter pan rather than over the filter screen. CAUTION Ensure that filter screen is in place prior to filter paper placement and filter pump operation. Improper screen placement is the primary cause of filtration system malfunction. Whenever the complaint is the pump is running, but no oil is being filtered, check the installation of the filter paper, and ensure that the correct size is being used. While you are checking the filter paper, verify that the O-ring on the bottom of the filter pan is present and in good condition. A missing or worn O-ring allows the pump to take in air and decreases its efficiency. Also, oil leaks on the floor each time a vat is drained. If the pump motor overheats, the thermal overload will trip and the motor will not start until it is reset. If the pump motor does not start, press the red reset switch (button) located on the rear of the motor. If the pump starts after resetting the thermal overload switch, then something is causing the motor to overheat. A major cause of overheating is when several frypots are filtered sequentially, thus overheating the pump and motor. Allow the pump motor to cool at least 30 minutes before resuming operation. Pump overheating can be caused by: Solidified shortening in the pan or filter lines, or Attempting to filter unheated oil or shortening (cold oil and shortening are more viscous, overloading the pump motor and causing it to overheat). If the motor runs but the pump does not, there is a blockage in the pump. Incorrectly sized or installed paper/pads will allow food particles and sediment to pass through the filter pan and into the pump. When sediment enters the pump, the gears bind, causing the motor to overload, again tripping the thermal overload. Shortening that has solidified in the pump will also cause it to seize, with the same result. A pump seized by debris or hard shortening can usually be freed by manually moving the gears with a screwdriver or other instrument. Sediment Particle Sediment Particle Oil Flow Up for reverse Down for forward -9
Disconnect power to the filter system, remove the input plumbing from the pump, and use a screwdriver to manually turn the gears. Turning the pump gears in reverse will release a hard particle. Turning the pump gears forward will push softer objects and solid shortening through the pump and allow free movement of the gears. Incorrectly sized or installed paper/pads will also allow food particles and sediment to pass through and clog the suction tube on the bottom of the filter pan. Particles large enough to block the suction tube may indicate that the crumb tray is not being used. Pan blockage can also occur if shortening is left in the pan and allowed to solidify. Blockage removal can be accomplished by forcing the item out with an auger or drain snake. Compressed air or other pressurized gases should not be used to force out the blockage..8. Replacing the Filter Motor, Filter Pump, and Related Components. Remove the filter pan and lid from the unit. Drain the frypots into an oil disposal unit (MSDU) or other appropriate metal container. DANGER DO NOT drain more than one full frypot or two split frypots into the MSDU at one time.. Disconnect the fryer from the electrical power supply and reposition it to gain access to both the front and rear. 3. Remove the two lower back panels, unplug the wiring harnesses from the contactor boxes, and remove the two screws that secure one of the boxes in place (it doesn t matter which one; see illustration on page -). NOTE: If you remove the screws from both boxes at the same time, the boxes will jam against each other and neither can be removed. 4. Carefully lower the box to the floor and pull it out the front of the fryer. Remove the remaining box following the same procedure.. Disconnect the two flexlines running to the oil-return manifold at the rear of the fryer. Remove the nut and bolt that secures the bridge to the oil-return manifold. Disconnect pump solenoid flexline here. Disconnect vacuum-breaker solenoid flexline here. -0
. Disconnect the pump suction flexline at the filter pan connection end. Disconnect pump suction flexline here.. Remove the cover plate from the front of the motor and disconnect the motor wires. 8. Unplug the -pin connector from the rear of the left component box and, using a pin pusher, disconnect the solenoid valve wires (pins 4,, 0 and ). NOTE: If the vacuum-breaker solenoid valve is connected to the manifold rather than the pump, its wires (pins 4 and ) do not need to be disconnected. 9. Remove the two nuts and bolts that secure the front of the bridge to the cross brace and carefully slide the bridge rearward off the cross brace until its front end can be lowered to the floor. Be careful not to let the rear of the bridge slip off the manifold at this point. NOTE: In some early production units, the bridge will not slide far enough to the rear to clear the front brace. In such cases, the front brace must be removed. It is held in place by two hex head screws on each end and a nut and bolt inside the brace near each end. 0. Get a good grip on the bridge, carefully pull it forward off the oil-return manifold, and lower the entire assembly to the floor. Once on the floor, pull the assembly out the front of the fryer.. When required service has been completed, reverse steps - to reinstall the bridge. NOTE: The black motor wires go on the top terminal, the white on the bottom. The pump solenoid valve wires go in positions 0 and of the -pin connector; the vacuum-breaker solenoid valve wires go in positions 4 and. In both cases, polarity does not matter.. Once the bridge is back in place, reverse steps 4 and to reinstall the contactor boxes. 3. Reconnect the unit to the electrical power supply, and verify that the pump is functioning correctly (i.e., when a filter handle is placed in the ON position, the motor should start and there should be strong suction at the intake fitting and outflow at the power shower or rear flush port). -
4. When proper operation has been verified, reinstall the back panels and the filter pan and lid, and return the fryer to service..8.3 Replacing the Filter Transformer or Filter Relay Remove the left controller from the fryer to expose the interior of the left component box. The filter transformer and relay are located as shown in the illustration below. NOTE: The right component box is identical to the left except that the filter transformer and relay are not present. Filter Relay Filter Transformer Dual-vat configuration illustrated. In full-vat units, left filter handle is not present. -
.9 Interface Board Diagnostic Chart The following diagram and charts provide ten quick system checks that can be performed using only a multimeter. Diagostic LEDs Diagnostic LED Legend 3 9 4 8 0 4 3 K K K3 K4 Left Latch Relay Left Heat Relay Right Heat Relay Right Latch Relay CMP indicates power from V transformer 4 indicates power from 4V transformer HI (RH) indicates output (closed) from right latch relay HI (LH) indicates output (closed) from left latch relay HT (RH) indicates output from right heat relay HT (LH) indicates output from left heat relay AL (RH) indicates output (open) from right latch relay AL (LH) indicates output (open) from left latch relay 0 4 0 4 8 8 9 3 9 3 Test Points J Left J Right Meter Setting Test Pin Pin Results VAC Power 0 VAC Scale of J 3 of J - VAC 4 VAC Power 0 VAC Scale of J Chassis 4-30 VAC *Probe Resistance (RH) R X 000 OHMS of J of J See Chart *Probe Resistance (LH) R X 000 OHMS 3 of J of J See Chart Hi-Limit Continuity (RH) R X OHMS of J 4 of J 0 - OHMS Hi-Limit Continuity (LH) R X OHMS 4 of J of J 0 - OHMS Latch Contactor Coil (RH) R X OHMS 8 of J Chassis 3-0 OHMS Latch Contactor Coil (LH) R X OHMS of J Chassis 3-0 OHMS Heat Contactor Coil (RH) R X OHMS 9 of J Chassis 8- OHMS Heat Contactor Coil (LH) R X OHMS of J Chassis 8- OHMS * Disconnect -Pin harness from the computer/controller before testing the probe circuit. -3
.0 Wiring Diagrams COMPONENT WIRING -4
CONTACTOR BOX DELTA CONFIGURATION -
CONTACTOR BOX WYE CONFIGURATION -
BIPH4/MPH4 SERIES ELECTRIC FRYERS CHAPTER : PARTS LIST. Accessories 3 4 8 9 0 ITEM STANDARD EURO-LOOK COMPONENT 809-0 Thumbscrew, ¼ -0 X 3 / 8 -inch 80-403 Hanger, Wireform Basket * 809-09 Spacer, Basket Hanger 3 803-09 Cleanout Rod, -inch 4 803-009 Brush, Frypot 83-88 Connecting Strip, Frypot 80-308 Cover, Full-Vat Frypot * 80-30 Cover, Dual-Vat Frypot 803-0099 Basket, Full-Vat 8 803-0 Basket, Dual-Vat (Twin) 9 803-0 Sediment Tray, Left Dual-Vat * 803-03 Sediment Tray, Right Dual-Vat * 803-03 Sediment Tray, Full-Vat 0 803-03 Rack, Full-Vat Basket Support 803-00 Rack, Dual-Vat Basket Support * 803-000 Powder, Filter (80 -Cup Applications) * 803-004 Cup, Plastic Measuring * 803-00 Pack, 00-Sheet Filter Paper * Not illustrated. Use standard part. -
. Cabinetry.. Back Panels, Control Panel Frames, Doors, Sides, Tilt Housings, and Top Caps 3 8 9 4 3 0 -
ITEM STANDARD EURO-LOOK COMPONENT Back Panel, Upper (Panel for five station fryer shown) 00-99 00-30 Two Station Fryer 00-380 00-8 Three Station Fryer 00-3490 00-8 Four Station Fryer 00-30 00-8 Five Station Fryer Back Panel, Center (Panel for five station fryer shown) 00-98 Two Station Fryer 00-39 Three Station Fryer 00-3489 Four Station Fryer 00-39 Five Station Fryer 3 Back Panel, Lower (Panel for five station fryer shown) 00-4430 00-44 Two Station Fryer 00-443 00-44 Three Station Fryer 00-443 00-448 Four Station Fryer 00-4433 00-449 Five Station Fryer 4 Frame, Control Panel (Frame for five station fryer shown) 80-SP 0-438 Two Station Fryer (use 0-SP for fryers mfd. After..0) 80-3SP 0-439 Three Station Fryer (use 0-08SP for fryers mfd. After..0) 80-4SP 0-439 Four Station Fryer (use 0-09 for fryers mfd. After..0) 80-9SP 0-4393 Five Station Fryer (use 0-00 for fryers mfd. After..0) 0-443 Side, Standard Cabinet Left or Right 80-34 Magnet, Door Tilt Housing (Housing for five station fryer shown) 84-0 84-303 Two Station, S/S 84-0 84-3 Two Station, Aluminized Steel 84-0 84-33 Three Station, S/S 84-08 84-338 Three Station, Aluminized Steel 84-03 84-33 Four Station, S/S 84-09 84-339 Four Station, Aluminized Steel 84-04 84-33 Five Station, S/S 84-00 84-340 Five Station, Aluminized Steel 8 8-3 809-00 Nut Retainer, ¼-0 (Pkg. of 0 receives basket hanger thumbscrew) 9 Top Cap (Top cap for five station fryer shown) (Also requires 809-008 Nutserts) 84-089 0-443 Two Station (use 0-9 for fryers mfd. After..0) 84-080 0-4438 Three Station (use 0-9 for fryers mfd. After..0) 84-08 0-4440 Four Station (use 0-98 for fryers mfd. After..0) 84-08 0-444 Five Station (use 0-99 for fryers mfd. After..0) Cap-N-Splash * 83-304 Two Station * 83-30 Three Station * 83-30 Four Station * 83-30 Five Station 0 80-4SP 0-439 Door, Left or Right (Left shown move handle to bottom for right) 809-0 Screw, #0 X ½-inch Phillips Truss Head 80-4 0-8 Handle, Wireform Door 3 0-04 Pin Assembly, Door * 80-0 Spring, Door Pin * 84-03 Housing, MAC4 HE Tilt with cap/splash * 84-034 Housing, MAC4 HE Tilt with cap/splash * 84-03 Housing, MAC34 HE Tilt with cap/splash * 84-03 Housing, MAC44 HE Tilt with cap/splash * Not illustrated. Use standard part. -3
.. Cabinet Bases, Braces, and Associated Parts See Page - for cabinet sides. See Page -30 for rear bridge support/oil return manifold. 8 3 0 4 0 4 9 4 4 4 8 8 0 4 4 4 4 3 See Page - for filter rails and associated hardware. 30 3 9 8 33 9 8 3 The -Station cabinet illustrated is typical of all BIPH4/MPH4 cabinets. All components used in BIPH4/MPH4 cabinets are identified, but not all components are used in every configuration. -4
ITEM STANDARD EURO-LOOK COMPONENT 0-SP Upright Assembly, Left 0-SP Upright Assembly, Right 3 00- Support, Cross Cabinet 4 00-9 Divider, Cabinet 00-93 Brace, Single Station Lower 00-34 Brace, Double Station Lower Brace, Front Horizontal 00-33 Two-Station Fryer 00-9 Three-Station Fryer 00-33 Four-Station Fryer 00-390 Five-Station Fryer 8 Brace, Rear Horizontal 00-84 Two-Station Fryer 00-9 Three-Station Fryer 00- Four-Station Fryer 00-39 Five-Station Fryer 9 00-44 Support, Contactor Box Right Station 3 or Station 0 0-44 Support, Contactor Box Left Station 4 or Station 0-44 Support, Contactor Box Right Station 3 00-443 Support, Contactor Box Stations 3 and 4 3 00-444 Support, Contactor Box Front to Rear 4 0-39 Support, Contactor Box Station 0-39 Support, Contactor Box Station 00-444 Post, Door 80-34 Magnet, Door 8 00-48 Support, Oil Return Manifold 9 0-9 Hinge, Door 0 0-490 Bracket, Rear Support 900-4 Bracket, Frypot 809-03 Bolt, ¼-0 X ¾-inch Hex Head (also used w/item to mount filter rails) 3 8-3 Screw, #8 X ½-inch Drill Point Hex Head (Pkg. of ) 4 8-330 Screw, 0-3 X ⅜-inch Slotted (Pkg. of, used to attach contactor box) 809-0 Nut, 0-3 Keps Hex 809-04 Screw, #0 X ½-inch Hex Washer Head (primary cabinet screw) 809-04 Nut, ¼-0 Hex Flange 8 809-049 Bolt, ¼-0 X -inch Hex Head 9 00-4 Brace, Rear Channel Corner 30 Channel, Base Rear 00-43 Two-Station Fryer 00-38 Three-Station Fryer 00-3 Four-Station Fryer 00-3 Five-Station Fryer 3 84-3 Channel, Base Side 3 80-03 Caster with Brake 33 80-03 Caster without Brake Use standard part. -
.3 Drain System Components.3. Drain Tube Sections and Associated Parts See Page -0 for Drain Valves 3 4 0 8 3 4 9 8 9 3 4 -
ITEM STANDARD ** COMPONENT 83-084 Nipple, ¾ X -inch NPT 8-009 Grommet, -inch Drain 3 8-34 Washer, -inch Drain (Pkg. of ) 4 809-034 Nut, -inch NPT Retainer 809-0893 Nut, 8-3 High Crown Acorn 8-348 Cover, Drain Cleanout (Pkg. of ) 8-00 Gasket, Drain Cleanout 8 Drain Tube, Left End Short 83-3380 Full-Vat 83-339 Dual-Vat 9 Drain Tube, Right End Short 83-49 Full-Vat 83- Dual-Vat 0 Drain Outlet 83-39 With Vacuum Breaker Vent 83-33 Without Vacuum Breaker Vent 80-49 Fitting, Quick-Connect Straight (receives Teflon vent tube) Drain Tube, Left End Short Vented 83-3 Full-Vat 83-3 Dual-Vat 3 Drain Tube, Right End Long 83-08 Full-Vat 83-43 Dual-Vat 4 Drain Tube, Open End Short 83-08 Full-Vat 83-0 Dual-Vat Drain Tube, Open End Long 83-0 Full-Vat 83-04 Dual-Vat 80-039 Clamp, Square Drain 809-040 Screw, 0-3 X ¾-inch Hex Head 8 809-0 Nut, 0-3 Keps Hex 9 8-003 Gasket, Square Drain * 8-08 Kit, Square Drain Clamp ( each of Items -8 and of Item 9) * 8-0 Tube, Teflon Vent * Not illustrated. ** See page -9 for an Euro-Look parts list. -
.3. Euro-Look Drain Tube and Associated Parts See Page - for Drain Valves 8 3 3 4 4-8
ITEM EURO-LOOK PART# ** COMPONENT Drain Tube, Left/Right End Short 83-4 Full-Vat 83-44 Dual-Vat Drain Tube, Left/Right Open Short 83-443 Full-Vat 83-44 Dual-Vat 3 Drain Tube, Right End Long 83-439 Full-Vat 83-438 Dual-Vat 4 Drain Tube, Left/Right Open Long 83-44 Full-Vat 83-440 Dual-Vat 83-489 Drain Outlet 8-0 Sleeve 809-099 Clamp 8 80-49 Fitting, Quick-Connect Straight (receives Teflon vent tube) * KIT033 Kit, Round Drain Clamp ( or Item and of Item ) * 8-0 Tube, Teflon Vent * Not illustrated. ** See page - for a standard parts list. -9
.3.3 Drain Valves and Associated Parts (Units with Built-In Filtration) -0
ITEM STANDARD ** COMPONENT 809-039 Nut, ⅜- -Way Hex Lock 900-934 Retainer, Dual-Vat Drain Valve Nut 3 83-433 Handle, Dual-Vat Drain Valve 4 80-0 Grip, Drain Handle 809-03 Nut, 4-40 Keps Hex 90-348 Cover, Dual Vat Drain Safety Switch 80-03 Microswitch, CE Straight Lever 8 8-00 Insulation, Drain Safety Switch 9 80- Washer, Teflon Drain Valve 0 809-09 Washer, ⅜-inch Flat 0-SP Bracket Assembly, Dual-Vat Drain Safety Switch 80-338 Valve, -inch Dual-Vat Drain 3 809-040 Nut, ½-3 -Way Hex Lock 4 84-0 Handle, Full-Vat Drain Valve 8-039 Cap, Red Handle 80-83SP Bracket Assembly, Full-Vat Drain Safety Switch 80-00 Valve,.-inch Full-Vat Drain * WIR0 Wire Bundle, Drain Safety Switch * Not illustrated. ** See page -3 for an Euro-Look parts list. -
.3.4 Euro-Look Drain Valves and Associated Parts (Units with Built-In Filtration) 4 3 Compression Washers Dual-Vat Drain Valve Assembly 0-3 0 8 9 Flat Washer 8 Plastic Washer 0 3 9 4 Compression Washers Full-Vat Drain Valve Assembly 0-30 8 9 8 0 -
ITEM EURO-LOOK ** COMPONENT 809-039 Nut, ⅜- -Way Hex Lock 900-934 Retainer, Dual-Vat Drain Valve Nut 3 83-433 Handle, Dual-Vat Drain Valve 4 80-0 Grip, Drain Handle 809-03 Nut, 4-40 Keps Hex 90-348 Cover, Dual Vat Drain Safety Switch 80-03 Microswitch, CE Straight Lever 8 8-00 Insulation, Drain Safety Switch 9 80- Washer, Teflon Drain Valve 0 809-09 Washer, ⅜-inch Flat 0- Bracket Assembly, Dual-Vat Drain Safety Switch 80-4 Valve, -inch Dual-Vat Drain 3 809-040 Nut, ½-3 -Way Hex Lock 4 84-0 Handle, Full-Vat Drain Valve 8-039 Sleeve, Red Handle 80-83 Bracket Assembly, Full-Vat Drain Safety Switch 80-08 Valve,.-inch Full-Vat Drain 8 00-49 Support, 3 Drain 9 900-93 Retainer, Full-Vat Drain Valve Nut 0 8-03 Round Drain O-Ring * WIR0 Wire Bundle, Drain Safety Switch *Not illustrated. ** See page - for a standard parts list..3. Drain Valves and Associated Parts (Units without Built-In Filtration) 4 3 ITEM STANDARD EURO-LOOK COMPONENT 80-9 Valve,.-inch Non-Filter Full-Vat Drain 80-9SP Valve, -inch Non-Filter Dual-Vat Left Drain 3 80-9SP Valve, -inch Non-Filter Dual-Vat Right Drain 4 8- Drain Extension,.-inch 8- Drain Extension, -inch Use standard part. -3
.4 Electronics and Wiring Components.4. Component Boxes 08-40V CE Boxes 0V and 480V Boxes 08-40V NON-CE Boxes 4 9 8 8 9 3 8 4 9 8 0 9 3 8 4 9 3 8 9 9 8 9 3 9 9 9 9 0 9 9 9 9 8 0 8 0 8 0 4 NOTE : The transformer on the left side of the component box is present only in units with built-in filtration and then only in the left component box. NOTE : See Page - for Component Box -Pin Wiring Harnesses. 3 9-4
ITEM STANDARD EURO-LOOK COMPONENT 0-3SP Box Assembly, Component 00-3300 Bracket, Component Box Strain Relief 3 80-949SP Terminal Block and Wire Assembly 4 80-00 Relay, 8 Amp ⅓ HP 4V Coil 80-003 Terminal, ¼-inch Push-on 80-0 Bushing, Heyco Plastic AB--00 80-3 Holder, AGC Panel-Mount ¼-inch Fuse 8 80-9 Fuse, 3 Amp Slow-Blow 9 80-80 Transformer, 08-40V 0VA 0 80-8 Transformer, 00-0V/4V 0VA 80-080 Transformer, 08-40V/4V 0VA 80-9 Transformer, 08-40V/V 30VA 3 80-08 Transformer, 00-0V/V 0VA 4 80-099 Transformer, 08-40V/V 43VA 8-3 Nut, 4-40 Keps Hex (Pkg. of ) 809-00 Nut, -3 Keps Hex 809-0349 Spacer, 4mm X mm Aluminum 8 8-39 Screw, 4-40 X ¾-inch Slotted Round Head (Pkg. of ) 9 809-039 Screw, #8 X ¼-inch Hex Washer Head 0 Interface Board 80-33SP Standard (Non-Triac), Full- or Dual-Vat 80-34SP Triac, Full- or Dual-Vat 80-393 Relay, Heat/Latch VDC SPDT A 00-3844 Guard, Finger 3 80-44 Plug Button 4 00-343 Brace, Component Box * 80-30 Speaker, 4-Watt * Not illustrated. Use standard part. -
.4. Contactor Boxes 4 30 30 3 3 9 9 0 30 8 4 3 4 3 OR 30 CONVENTIONAL CONFIGURATION 4 3 WYE configurations also have Item 9, mounted with Items and 8, here. 8 4 3 OR 30 TRIAC CONFIGURATION NOTE: See Pages - and - for Contactor Box Wiring Harnesses - 3 3 OR 8 30 30 3
NOTES: Left and right contactor box assemblies are mirror images of one another. With the exception of the box itself, all components of a left-hand assembly are the same as those in the corresponding right-hand assembly and vice versa. The configurations illustrated show all possible components, but a particular configuration may not have all the components shown. ITEM STANDARD EURO-LOOK COMPONENT 0-3SP Box Assembly, Left Contactor 0-3SP Box Assembly, Right Contactor 3 00-3 Cover, Cord Cutout 4 900- Plate, Cordset Adapter 00-334 Door, Contactor Box Hinged 00-4 Door, Contactor Box 80-09 Hinge, Contactor Box Door 8 80-000 Terminal, Ground Lug 9 00-33 Bracket, Contactor Box Fuse Block 0 80-00 Fuse Block, 3-Pole 80-40 Fuse, 0 Amp 300VAC 00-33 Bracket, Mercury Contactor 3 80-0 Contactor, 4V 30 Amp Mercury 4 80-0884 Contactor, 4V 3-0 Amp Mercury 80-0 Contactor, 4V 40 Amp 3-Pole 809-0448 Clip, Tinnerman ** 80-84 Heatsink Assembly, DV Solid State Relay (See components below) 8** 80-83 Heatsink Assembly, FV Solid State Relay (See components below) 9 80-94 Filter Assembly, Triac (used in Wye-configured Triac units only) 0 8-38 Nut, -3 Keps Hex (Pkg. of ) 8-3 Screw, -3 X ⅜-inch Slot Head (Pkg. of ) 809-004 Screw, 8-3 X ½-inch Slot Head 3 8-330 Screw. 0-3 X ⅜-inch Slot Head (Pkg. of ) 4 809-03 Screw, #0 X ¾-inch Slot Head 8-3 Nut, 4-40 Keps Hex (Pkg. of ) 809-04 Nut, 8-3 Keps Hex 8-3 Nut, 0-3 Keps Hex (Pkg. of 0) 8 8-39 Screw, 4-40 X ¾-inch Slot Head (Pkg. of ) 9 809-039 Screw, #8 X ¼-inch Hex Washer Slot Head 30 809-030 Screw, #8 X ⅜-inch Hex Washer Slot Head 3 8-34 Screw, #0 X ½-inch Hex Head (Pkg. of ) * 00- Lid, Left or Right Contactor Box * Components of Items and 8 ** 80- Relay, Solid State 0 Amp 80V * 8- Heatsink, Solid State * 80-003 Terminal, ¼-inch Push-on * 809-009 Screw, -3 X ⅝-inch Slot Head * Not illustrated. Use standard part. ** Dual-vat assembly has six relays (8-); full-vat assembly has three relays. -
.4.3 Heating Element Assemblies and Associated Parts FULL-VAT ELEMENT ASSEMBLY DUAL-VAT ELEMENT ASSEMBLY 4 3 9 8 8 0 3 0 3 4 9 NOTES: The dual-vat assembly is the same as the full-vat assembly except for having two of Items, four of Item instead of two of Item, and two of Item 0 instead of one of Item 0 and one of Item. The only difference between element assemblies for different voltage and kw ratings is the element itself (Item ) Items 9 and 0 are shown as associated parts. They are not part of either element assembly. -8
ITEM STANDARD EURO-LOOK COMPONENT Element 8-00V.0 kw 8-49 08V.0 kw 8-0V.0 kw 8-30V.0 kw 8-3 30V/400V.0/8. kw (used in export 3-phase 4-wire wye units) 8-4 40V.0 kw 8-480V.0 kw 8- Probe, Temperature 3 0-0004SP Tilt Plate Assembly 4 0-0SP Bracket, Left Spring Slot 0-03SP Bracket, Right Spring Slot 90-94 Tilt Plate 80-003 Hinge 8 8-330 Screw, 0-3 X ⅜-inch Slotted Truss Head (Pkg. of ) 9 8-3 Nut, 0-3 Keps Hex (Pkg. of 0) 0 8-339 Bushing,.3-inch Split (Pkg. of 0) 8-0480 Plug,.3-inch Dome 90-0 Bracket, Temperature Probe 3 809-08 Screw, 8-3 X ⅜-inch Slotted Hex Head 4 90-04 Clamp, Element (Short) 90-3 Clamp, Element (Long) 90-38 Support, Full-Vat Element Rear 90-4 Support, Dual-Vat Element Rear 8 809-0 Tie-Wrap, Metal 9 00-00 Bracket, Lower Spring Slot 0 80-09 Spring, Element * 8-0 Tilt Switch, Mercury Non-CE (Full-Vat requires one switch and Dual-Vat requires two.) * 8-8 Tilt Switch (CE fryers) (Full-Vat requires one switch and Dual-Vat requires two.) * Not illustrated. Use standard part. -9
.4.4 Computers NOTE: See Page - for Interface Board to Computer Wiring Harness ITEM STANDARD COMPONENT Replacement Computer (without bezel), Dual- or Full-Vat 0-09B Non-CE 0-43B CE 83-98 Replacement Bezel ITEM EURO-LOOK COMPONENT Replacement Computer (without bezel) 0-9 Non-CE 0-0 CE 0-3 Replacement Frame Assembly -0
.4. Wiring.4.. Contactor Box Wiring Assemblies -Pin Dual-Vat C- 3 4 8 9 0 WHITE BLACK BLACK GREEN/YELLOW WHITE BROWN ORANGE BLACK ORANGE BLACK 3 4 8 9 0 WHITE BLACK BLACK GREEN/YELLOW WHITE BROWN ORANGE BLACK ORANGE BLACK YELLOW ITEM STANDARD EURO-LOOK 0-48SP Standard 0-343SP Triac COMPONENT Use standard part. -
.4.. Contactor Box Wiring Assemblies -Pin Full-Vat C- 3 4 8 9 0 WHITE BLACK BLACK GREEN/YELLOW WHITE BROWN ORANGE BLACK 3 4 8 9 0 WHITE BLACK BLACK GREEN/YELLOW WHITE BROWN ORANGE BLACK YELLOW ITEM STANDARD EURO-LOOK Standard 0-44SP Other than 480V 0-SP 480V 0-4SP Triac COMPONENT Use standard part..4..3 Contactor Box Wiring Assembly -Pin (Left Element) 3 4 BLUE BLUE BLUE BLACK BLACK BLACK 0-4SP.4..4 Contactor Box Wiring Assembly 9-Pin (Right Element) 3 4 8 9 BLUE BLUE BLUE BLACK BLACK BLACK 0-4SP -
.4.. Main and Multi-Fryer Wiring Harnesses -Pin Male Connector 80-00 C -Pin Male Connector 80-0804 C J J J4 J J 4-Pin Female Connector 80-33 -Pin Male Connector 80-0804 -Pin Male Connector 80-0 -Pin Male Connector 80-00 -Pin Male Connector 80-00 Male Disconnect Pin 80-049 Female Disconnect Pin 80-00 -Pin Male Connector 80-00 Female Disconnect Pin 80-00 Male Disconnect Pins 80-049 FRYER #3 FRYER #4 FRYER # Item 3: 80-3 Item 4: 80-3 Item : 80-38 -Pin Connector Wiring for 80-3 -Pin Connector Wiring for 80-3 -Pin Connector Wiring for 80-38 -3
ITEM STANDARD EURO-LOOK COMPONENT 80-39 Main 80-3 Two-Fryer Battery 3 80-3 Three-Fryer Battery 4 80-3 Four-Fryer Battery 80-38 Five-Fryer Battery NOTE: Harnesses for 3-, 4-, and -Fryer Batteries are similar to 80-3 but have extra sets of leads as appropriate for the number of fryers in the battery. The connections to Fryer # J and J4 are the same for all. Use standard part..4.. Component Box Wiring Harnesses -Pin 3 4 ITEM STANDARD EURO-LOOK COMPONENT 0-0SP 08-480V (With Filter) 0-0SP 08-480V (Without Filter) 3 0-08SP 0V (With Filter) 4 0-09SP 0V (Without Filter) Use standard part..4.. Interface Board to Controller Wiring Harness -Pin 80-0SP -4
. Filtration System Components NOTE: Some early production units were configured this way. 3 38 8 4 3 9 3 9 34 0 8 4 3 8 30 3 8 3 0 9 8 4 4 33 3 3 -
ITEM STANDARD EURO-LOOK COMPONENT * 8-99 Filter Pan Roller Kit (four each of Items and 8) * 8-980 Service Filter Pan (Item, four of Items & 8, two o-rings, two 83-08) * 8-98 8-98 Service Filter Pan Assembly (Service Filter Pan plus Items 3 and 4) * 8-39 O-Ring (Pkg. of ; used with Item ) * 83-08 Plug, ⅛-inch Socket Head Pipe (used with Item ; two required) * 8-0 Tubing, ¼-inch OD Teflon Vent (sold by the foot) * 0-8SP Heater Strip Assembly, 00-0V * 0-8SP Heater Strip Assembly, 08-0V 83-43 83-48 Lid (for units built before Feb 04, use 83-439) 80-43 Crumb Tray 3 80-83 Hold-Down Ring (two are needed for pad hold-down option) 4 00-4 SanaGrid Filter Screen 0-SP Pan, One-Piece Filter (includes Item ) 80-0 Rail Set, Filter Pan Roller (includes one left and one right) 80-98 Roller, Filter Pan and Rail 8 8-38 809-04 Nut, ¼-0 Hex Flange (Pkg. of 0) 9 83-489 Bracket, Lid Support (for units built before Feb 04, use 83-38) 0 Guide, Filter Pan Lid 00-3 Left 00-09 Right 809-004 809-003 Screw, 8-3 X ½-inch Slotted Truss Head 809-04 Nut, 8-3 Hex Keps 3 83-389 Suction Tube 4 00-4408 Rail, Left Filter 00-4409 Rail, Right Filter Motor and Gasket Kit 8-8 80-388 00V 0/0 Hz 8-80-389 V 0/0 Hz 8-80-380 08V 0/0 Hz 8-80-38 0-40V 0/0 Hz 8-80-38 0V 0/0 Hz 8-4 Pump and Gasket Kit 80- Pump, Viking 4GPM -piece 8-0093 Gasket, Pump/Motor 8 80-484 Valve, ¼-inch Solenoid 9 83-0 Elbow, ½-inch 90 Street 0 83-034 Elbow, ½-inch 4 Street 83-030 Tee, ½-inch X ¼-inch X ½-inch Reducing 83-00 Nipple, ½-inch Close 3 83-0838 Nipple, ¼-inch Close 4 83-0304 Bushing, ½-inch to ¼-inch Flush 80-8 Adapter, ⅝-inch to ½-inch NPT Male 80-9 Adapter, ⅝-inch to ½-inch NPT Female 80-80 Flexline,.-inch Oil Return 8 80-39 Flexline,.-inch Oil Return Use standard part. Continued on next page -
9 80-0 Flexline,.-inch Oil Return 30 80-388 Cable, FootPrint Pro Pump Motor 3 8-3 809-040 Screw, 0-3 X ¾-inch Hex Trim Head (Pkg. of ) 3 00-90 00-84 Bridge, Filter Motor 33 0-349 Support, Contactor Box 34 83-0003 83-0003 Tee, ½-Inch 3 83-098 83-098 Nipple, ½-inch.0-inch 3 83-03 83-03 Nipple, ¼-inch.0-inch 3 80-493 80-493 Fitting, ¼-inch X 90 Quick-Connect 38 80-0 Flexline, 3.0-inch Oil Return * 80-043 Flexline, 0.-inch Oil Return * 80-0 Flexline, 3.0-inch Oil Return * Not illustrated. Use standard part. -
. Frypot Assemblies and Associated Parts 9 8 3 0 8 4-8
ITEM STANDARD EURO-LOOK COMPONENT 80-8SP Frypot Assembly, Full-Vat Non-Filter Triac (does not include Item ) 83-4SP Frypot, Full-Vat Non-Filter w/o Insulation (for use on non-triac units) 3 83-44SP Frypot, Full-Vat Filter w/o Insulation (use 80-89SP for Triac units) 4 83-4SP Frypot, Dual-Vat Non-Filter w/o Insulation (use 80-80SP for Triac units) 83-40SP Frypot, Dual-Vat Filter w/o Insulation Thermostat Assembly, High-Limit 80-43 Non-CE Full Vat 4 F (8 C) (Color Coded Black) 80-803 Non-CE Dual Vat 43 F (4 C) (Color Coded Red) 80-83 CE Full and Dual Vat 4 F (3 C) (Color-Coded Yellow) 8-0 Insulation, Kaowool -inch X 0-inch X ½-inch (4 required per pot) 8 900-400 Retainer, Side Insulation 9 900-40 Retainer, Front Insulation 0 900-34 Retainer, Rear Insulation 8-3 Nut, 0-3 Keps Hex (Pkg. of 0) NOTES: The frypots for Triac-equipped units are insulated; those for non- Use standard part. Triac (standard) units are not. Triac frypot assemblies 80-89SP and 80-80SP consist of the Items 3 and 4 respectively, plus insulation (Items -0). When replacing insulation or adding insulation to a bare frypot, the individual pieces (sides, front, and back) are cut to fit from Item when installed. Each frypot requires four uncut pieces of insulation. -9