TILTING DITCHING BUCKET POWERTILT TILTING COUPLER Single large bore double acting ram Cover plate for ram protection Replaceable bushes on main pivot Greaseable pivot pin Up to 180 degrees of tilt Use with any attachment, even narrowest trenching bucket Built in quick hitch No external rams Built in hydraulic overload protection MODEL MAXIMUM APPROXIMATE TOTAL TILT REQUIRED CIRCUIT MACHINE POWERTILT OIL FLOW PRESSURE WEIGHT KG WEIGHT KG - L/MIN RANGE MACHINE PART NO. WIDTH B CAPACITY 4.5 1,800 40 180 2-4 WEIGHT (MM) 6N 3,800 75 180 3-6 2 to 4 Ton 166T/48 50 " 0.10 6W 4,775 85 180 3-6 5 to 9 Ton 003T/60 60 " 0.16 7 6,800 145 180 6-12 220-240 Bar 9 to 12 Ton 150T/60 60 " 0.23 (Applies to 8 9,100 195 180 12-20 all models) 13 to 15 Ton 184T/72 72 " 0.42 9 13,000 260 134 24-28 16 to 19 Ton 297T/72 72 " 0.49 10 20,000 385 134 24-32 20 to 27 Ton 286T/84 84 " 0.62 11 27,000 545 134 32-44 1 x double acting low flow circuit 12 34,000 680 134 36-52 Quick Hitches Powertilt Tiltrotator Abiljo, England Hydraulic quick hitch circuit Hydraulic tilt circuit 1 x double acting low flow circuit (all models) + hitch circuit for hydraulic coupler models Tilting Ditching Bucket Tiltrotator Helac Corporation / Exac-One Ltd (USA / England) page 6 page 7
TILTROTATOR TILTROTATOR Continuous Rotation 80 degrees of tilt Choice of top mountings Choice of hydraulic quick hitches to underside Additional hydraulic circuits for grab operation etc. Continuous Rotation 80 degrees of tilt Choice of top mountings Choice of hydraulic quick hitches to underside Additional hydraulic circuits for grab operation etc. MODEL EC 02 EC 05 A MODEL EC 10 EC 15 EC 20 EC 30 WIDTH A (MM) 180 260 WIDTH A (MM) 320 320 360 500 WIDTH B (MM) 155 215 WIDTH C (MM) 160 160 E WIDTH B (MM) 245 285 300 390 WIDTH C (MM) 290 307 310 390 TOTAL LENGTH D (MM) 435 485 B C D TOTAL LENGTH D (MM) 485 698 800 970 BUILD HEIGHT E (MM) 435 315 BUILD HEIGHT E (MM) 420 440 450 740 WEIGHT From 65 From 125 WEIGHT From 250 From 340 From 440 From 850 TILT 2x40 2x40 TILT 2x40 2x40 2x40 2x40 OIL FLOW REQUIRED (L/MIN) 15-35 15-40 OIL FLOW REQUIRED (L/MIN) 20-40 40-60 40-60 40-80 WORK PRESSURE (L/MIN) 18-21 18-21 WORK PRESSURE (L/MIN) 18-21 18-21 18-21 18-21 MACHINE WEIGHT (TONNES) 1.5-3 3-6 MACHINE WEIGHT (TONNES) 6-12 12-16 16-22 22-32 ROTATION Infinite Infinite ROTATION Infinite Infinite Infinite Infinite OPTIONAL GRAB TYPE *DEPENDING ON MODEL - 05 or 10 OPTIONAL GRAB TYPE *DEPENDING ON MODEL 10 05 or 10 20 20 EC02/05 Grabs TYPE MAXIMUM WIDTH LENGTH WEIGHT MAX. GRAB WIDTH A B C (MM) HYDRAULIC (MM) (MM) PRESSURE A B EC10/30 Grabs TYPE MAXIMUM WIDTH LENGTH WEIGHT MAX. GRAB WIDTH A B C (MM) HYDRAULIC (MM) (MM) PRESSURE 5 370 200 585 50 210 10 610 270 780 70 210 C 10 610 270 780 70 210 20 790 350 910 85 210 Hoses (without q/r couplings) 1 x single acting circuit (all models) Hoses (without q/r couplings) 1 x single acting circuit (all models) Standard installation kit c/w stere-strip controls Integrated grab Replacement multi button joysticks Integrated proportional control Tilting ditching bucket Powertilt Engcon (Sweden) Standard installation kit c/w stere-strip controls Integrated grab Replacement multi button joysticks Integrated proportional control Tilting ditching bucket Powertilt Engcon (Sweden) page 8 page 9
V BUCKETS RIDDLE BUCKETS Manufactured from high grade steel Are custom made to individual requirements Made to order based on dimensions A-B-C Abiljo (England) Description Riddle Buckets are available for 1 to 40 ton excavators for the sorting of materials on site. The information given below indicates examples of the standard sizes that are normally used, although buckets to any size and specification can be manufactured. All riddle buckets are fitted with Kingmett teeth as standard. Riddle buckets are manufactured using two different methods depending on the size of the carrier machines: Smaller buckets are manufactured with a thicker than standard back plate, that then have the holes profiled into it, whilst for larger machines, individually profiled riddles are spaced to the required gap and are then welded into place with two supporting cross bars added to give additional strength. A B MODEL MACHINE WIDTH FLOOR TYPE FLOOR / RIDDLE STANDARD WEIGHT (INCHES) THICKNESS GAP (TONNES) (MM) (INCHES) C ED0/24R(S) 1-2 24 Profiled 8 2 ED1/30R(S) 2-3 30 Profiled 8 2 ED2/30R(S) 3-4 30 Profiled 8 2.5 ED3/36R(S) 4-5 36 Ribbed 10 2.5 ED4/36R(S) 5-6 and Backhoes 36 Ribbed 10 2-3 ED5/42R(S) 6-9 42 Ribbed 12 2-3 ED6/42R(S) 9-11 42 Ribbed 12 2-3 16/R48S 12-15 48 Ribbed 15 3-4 35R54S 16-19 54 Ribbed 15 3-4 225R60S 20-25 60 Ribbed 15 3-4 210R66S 26-31 66 Ribbed 20 3-4 Abiljo (England) page 12 page 13
POWERGRIP BUCKET CRUSHA BUCKET Range of excavator mounted 4 in 1 type buckets to suit excavators from 5 tonnes to 20 tonnes. Powergrip incorporates Helac Corporation s proven helical rotary actuator which ensures constant gripping and holding force and maximum safety. 120 degrees of jaw movement and excellent holding torque gives superb versatility on a range of digging and handling jobs. No external cylinders or moving parts ensures maximum durability and minimum maintenance. MODEL WIDTH (MM) TYPE MACHINE POWERGRIP HEAPED WEIGHT WEIGHT CAPACITY (M3) (TONNES) PG06-24-5T 600 Trenching 5 240 0.17 PG06-24-7T 600 Trenching 7 318 0.28 PG06-30-7T 750 Trenching 7 386 0.37 PG07-24-10T 600 Trenching 10 410 0.29 PG07-30-10T 750 Trenching 10 445 0.39 PG07-36-10T 900 Trenching 10 530 0.48 PG07-24-14T 600 Trenching 14 605 0.35 PG07-30-14T 750 Trenching 14 665 0.47 PG07-36-14T 900 Trenching 14 760 0.59 PG07-48-14T 1200 Trenching 14 925 0.85 PG08-30-21T 750 Trenching 21 1020 0.58 PG08-36-21T 900 Trenching 21 1090 0.73 PG08-42-21T 1050 Trenching 21 1195 0.87 PG08-48-21T 1200 Trenching 21 1375 1 PG07-60-21T 1200 Ditching 21 920 0.90 PG07-48-21T-DM 1500 Ditching 21 1060 1.2 1 x double acting circuit Integral check valve Integral cross line pressure relief valve Cat type teeth Mounting bracket Ditching bucket includes two bolt on cutting edges A range of low impact jaw type crusher buckets to suit excavators from 2.5 tonnes - 10 tonnes. These buckets will process stone, brick, concrete (with or without re-inforcing), etc to re-usable materials. The size of the output material can be regulated over a nominal range of 50mm - 100mm using the supplied adjustment plates. Advanced hydraulics provide a fully automatic reciprocating action to the jaw, operating off the excavator's standard single acting breaker circuit. MODEL CB25 CB40 CB80 EXCAVATOR WEIGHT (TONNES) 2.5-4 4-6 6-10 DIM A (MM) 560 600 750 DIM B (MM) 850 1050 1210 DIM C (MM) 1050 1100 1300 DIM D (MM) 520 520 640 DIM E (MM) 310 350 450 NOMINAL PRODUCT SIZE F (MM) <50/<75/<100 <50/<75/<100 <50/<75/<100 WEIGHT 350 480 890 OPERATING PRESSURE (BAR) 200-210 200-210 200-210 REQUIRED FLOW (L/MIN) 40-50 50-70 50-80 JAW CYCLES PER MINUTE 12-16 11-16 9-14 CRUSHING RATE (TONNES/HOUR UP TO 5 UP TO 7 UP TO 10 subject to material type - guide only) 1 x single acting circuit Mounting bracket Hoses (no q/r couplings) Anross, England page 14 page 15
MIXER BUCKET EXCAVATOR THUMBS Range of concrete/ mortar mixing buckets to suit excavators from 4 tonnes to 12 tonnes. Includes hydraulically operated chute for accurate placing of mixed material and comes complete with electronic changeover valve. Operates off excavators standard double acting breaker circuit. Range of thumbs to suit excavators from 1 tonne to 40 tonnes. This low cost alternative to a grapple can be fitted the the excavator in around four hours. Fitting involves welding the pivot to the inside of the dipper arm. MODEL MIX 150 MIX 200 MIX 250 MIX 350 MACHINE WEIGHT (TONNES) 4-5 5-7 7-9 9-12 WIDTH (MM) 1260 1260 1480 1580 CAPACITY (M3) 0.15 0.20 0.25 0.35 WEIGHT 260 275 380 425 OIL FLOW REQUIRED (L/MIN) 25-40 25-40 40-90 50-90 OIL PRESSURE REQUIRED (BAR) 140 140 160 160 MAXIMUM OIL PRESSURE (BAR) 160 160 240 240 DIM A (MM) 1260 1260 1480 1580 DIM B (MM) 760 810 784 865 DIM C (MM) 580 665 696 760 MODEL MACHINE WIDTH (MM) HEIGHT (MM) WEIGHT (TONNES) TH10 1-4 255 600 TH40 4-9 410 950 TH90 9-15 510 1200 TH160 16-27 640 1500 TH280 28-37 900 1800 TH380 38-48 1200 2100 1 x double acting circuit Mounting Bracket Hoses (excl q/r couplings) Nil Mounting kit Manufactured By Cangini, Italy Abiljo, England page 16 page 17
MINI - HAMMER SOLID LEG GRAPPLE Silenced Non accumulator type Interchangeable mounting brackets 3/2 tine standard configuration Excavators bucket ram operates moving jaw No additional equipment required on excavator Suitable for general waste handling to rock handling MODEL MACHINE WIDTH OF WIDTH OF MAXIMUM WEIGHT MOVING STATIC OPENING C (TONNES) JAW A JAW B (APPROX MM) (MM) (MM) SLG10 1 230 420 600 A MODEL EXCAVATOR WEIGHT REQUIRED WORKING IMPACT IMPACT LENGTH CLASS OIL FLOW PRESSURE RATE ENERGY (MM) RATE (L/MIN) (BAR) (BPM) (JOULE) SLG20 2 to 4 320 590 950 SLG40 4 to 6 500 850 1550 C B MH 10S 0.7-2.5 102 15-25 80-110 800-1,400 208 1155 MH 20S 1.2-3.0 126 20-40 90-120 700-1,200 280 1262 MH 30S 2.5-4.5 152 25-50 90-120 600-1,100 320 1342 MH 40S 4.0-7.0 295 30-60 110-140 600-1,100 690 1600 MH 43S 6.0-9.0 375 40-80 130-150 400-800 900 1825 MH 45S 7.0-14 580 60-100 130-160 400-800 1,300 2101 SLG60 6 to 9 500 850 1750 SLG90 9 to 11 600 950 1850 SLG130 12 to 15 750 1100 2300 SLG160 16 to 19 750 1100 2300 SLG200 20 to 27 750 1200 2700 SLG280 28 to 37 760 1300 2900 Hoses (no q/r fittings) Mounting bracket (to suit direct mount or quick hitch) 2 standard chisels Tool kit 2 year warranty Wedge Chisel (standard) Moil point Asphalt cutter Post driving kit Quick hitch mount Direct mount Brace arm and brace arm mounting pad Mini-Grapple Orange Peel grab Jisung (South Korea) Abiljo (England) page 18 page 19
MINI - GRAPPLE (SORTING GRAB) POM ORANGE PEEL GRAB Grab arms manufactured from Hardox Grab hoses protected inside grab body Light weight Integral fixed head rotator Bolt on cutting edges POM Grab for stone and rocks MODEL TEETH MAX WEIGHT MAX A B C D E ø FxG LOAD BAR MODEL EXCAVATOR WEIGHT MAX. CAP A B C TEETH CLOSING MAX. WEIGHT BAR LT (OPTIONAL) FORCE LOAD UP TO N (TONNES) POM-3/380 3 2500 450 250 1340 1680 1180 1370 2000 32x80 POM-4/550-P 4 5000 850 300 1300 2050 950 1160 2150 50x100 POM-5/1000P 5 8000 1350 350 1400 2250 1640 1940 2453 70x150 MG3 2.5 115 220 50 920 350 775 3 750 500 MG4 3.5 265 220 100 1230 450 975 3 900 900 MG5 5 285 220 100 1230 450 1015 3 900 900 I FxG MG8 8 385 220 180 1510 550 1075 3 1200 1500 D C Mounting bracket (2 pin or dedicated coupler type) A B E Bolt on teeth Bolt on sideplates (to create clamshell bucket) to operate from one double acting circuit) Available with or without rotator 1 x double acting circuit if used with diverter control kit 2 x double acting circuit if used without diverter control kit Powertilt Tiltrotator Quick hitches Single pin mounting link Quick hitch mounting plate to operate from one double acting circuit) page 20 page 21
PFO ORANGE PEEL GRAB PFO/P ORANGE PEEL GRAB PFO Compact grab for general purpose use including scrap metal and urban waste PFO/P Heavy duty compact grab MODEL TEETH CAP. WEIGHT MAX A B C D E ø FxG MAX LT BAR LOAD PFO-4/100 4 100 105 250 750 1070 580 750 1200 25x30 1500 PFO-5/100 5 100 140 250 750 1070 580 750 1200 25x30 1500 PFO-4/120 4 120 220 250 850 1170 690 850 1350 30x60 1500 PFO-4/160 4 160 240 250 920 1400 760 990 1570 30x60 2000 MODEL TEETH CAP. WEIGHT MAX A B C D E ø FxG MAX LT BAR LOAD PFO-5/400-P 5 400 800 300 1250 1800 870 1050 1830 50x100 5000 PFO-6/400-P 6 400 920 300 1250 1800 900 1150 1900 50x100 5000 PFO-5/600-P 5 600 950 300 1380 1920 960 1200 2080 50x100 5000 PFO-6/600-P 6 600 1050 300 1380 1920 960 1200 2080 50x100 5000 PFO-5/220 5 200 280 250 970 1400 780 990 1580 30x60 2500 PFO-5/250 5 250 330 250 1000 1430 750 920 1620 32x80 2500 PFO-6/270 6 270 400 250 1020 1500 750 920 1620 32x80 3000 PFO-4/300 4 300 360 250 1110 1600 850 1010 1750 32x80 3000 PFO-5/300 5 300 424 250 1160 1600 850 1010 1750 32x80 3000 PFO-6/320 6 320 470 250 1160 1720 950 1010 1750 32x80 3000 PFO-5/400 5 400 540 250 1250 1860 870 1050 1830 35x80 3000 PFO-6/400 6 400 590 250 1250 1860 870 1050 1830 35x80 3000 Single pin mounting link Quick hitch mounting plate to operate from one double acting circuit) Single pin mounting link Quick hitch mounting plate to operate from one double acting circuit) page 22 page 23
PFV/P ORANGE PEEL GRAB LOG GRAB PFV/P Extra heavy duty grab with vertical cylinders Compact general purpose timber / log grab with special anti-yield jaws MODEL TEETH CAP. WEIGHT MAX A B C D E ø FxG MAX LT BAR LOAD PFV-5/500-P 5 500 1100 350 1210 1840 1500 1690 2000 50x100 5000 PFV-6/500-P 6 500 1250 350 1250 1840 1500 1690 2000 50x100 5000 PFV-5/650-P 5 650 1200 350 1300 1960 1610 1830 2130 50x120 5000 PFV-6/650-P 6 650 1350 350 1360 1960 1610 1830 2130 50x120 6000 MODEL CAP./M2 WEIGHT A B C D E F G MAX LOAD PTO-200/S 0.2 114 75 520 650 1395 350 435 730 1500 PTO-300/S 0.3 165 85 550 780 1520 425 510 850 2000 PTO-400/S 0.4 274 110 720 870 1880 520 710 985 2500 PTO-550/S 0.55 420 115 780 1050 2150 600 840 1120 4500 PFV-5/800-P 5 800 1350 350 1400 2250 1640 1940 2430 50x150 7000 PFV-6/800-P 6 800 1550 350 1480 2250 1640 1940 2430 50x150 7000 PFV-6/1000-P 6 1000 2000 350 1510 2420 1680 2120 2580 70x150 7000 C F B A D G E Single pin mounting link Quick hitch mounting plate to operate from one double acting circuit) Short arm version (can be used in conjunction with fixed head rotator for pole / column erecting) Single pin mounting link Quick hitch mounting plate to operate from one double acting circuit) Tiltrotator page 24 page 25
KERB - GRIP VEGETATION GRAB Constructed from Weldox 700 Check valve on ram Fixed jaw has nylon blade to separate kerbs in the pack Grab for handling bulky vegetation MODEL RECOMMENDED CARRIER KERB TYPES RATED CAPACITY KERB-GRIP LIGHT Excavators under 2 tonnes 10x5 s, radius, taper, 80kg half batter, natural stone KERB-GRIP-STANDARD Excavators over 2 tonnes 10x5 s, radius, taper, 80kg and truck cranes half batter, natural stone MODEL TEETH WEIGHT MAX A B C D E MAX BAR LOAD FLO 10 10 145 250 1250 1020 680 580 650 600 FLO 12 12 165 250 1250 1020 680 580 800 700 FLO 14 14 185 250 1250 1020 680 580 950 800 KERB-GRIP SUPER Excavators over 3 tonnes 10x5 s, large granite, beany, 400kg and truck cranes conservation, trieffe, bus stop Direct mount Single pin mounting link Quick hitch mounting plate to operate from one double acting circuit) Single pin mounting link Quick hitch mounting plate to operate from one double acting circuit) page 26 page 27
BMV-P CLAMSHELL BUCKET BM0-P CLAMSHELL BUCKET BMV-P Heavy duty clamshell with two vertical cylinders suitable for digging and loading BMO-P Heavy duty clamshell with two horizontal cylinders MODEL CAP/LT WEIGHT MAX. MAX A B C D E MAX LOAD BAR LOAD BMV-2 / 1000-P 1050 1500 5,000 300 2400 1950 2000 1400 1000 5000 BMV-2 / 1300-P 1350 1700 5,000 300 2400 1950 2000 1400 1300 5000 BMV-2 / 1500-P 1600 1900 5,000 300 2400 1950 2000 1400 1500 5000 MODEL CAP/LT WEIGHT MAX A B C D E MAX BAR LOAD BMO-500/P2 500 550 250 1650 1160 950 750 1030 2500 BMO-700/P2 700 710 300 2160 1450 1250 1030 800 2500 BMO-1000/P2 1000 850 300 2160 1450 1250 1030 1050 3000 BMO-1200/P2 1200 1050 300 2160 1450 1250 1030 1200 3500 BMO-1500/P2 1500 1150 300 2160 1450 1250 1030 1500 3500 BMO-2000/P2 2000 1450 300 2160 1450 1250 1030 2000 5000 Direct mount Single pin mounting link Quick hitch mounting plate to operate from one double acting circuit) Direct mount Single pin mounting link Quick hitch mounting plate to operate from one double acting circuit) page 28 page 29
BL CLAMSHELL BUCKET BMV-2 CLAMSHELL BUCKET BL Range Light / medium duty Clamshell for material handling BMV-2 Clamshell with vertical cylinders suitable for digging MODEL CAP/LT WEIGHT A B C D E MAX LOAD BL - 250 250 220 1420 1060 750 675 700 600 BL - 350 350 250 1420 1060 750 675 850 700 BL - 450 450 270 1420 1060 750 675 1000 800 MODEL CAP/LT WEIGHT A B C D E MAX LOAD BMV-2/200-S 175 240 1340 1230 1170 940 270 1500 BMV-2/250 250 260 1340 1230 1170 940 520 1500 BMV-2/350 350 280 1340 1230 1170 940 670 1500 BMV-2/500 500 300 1340 1230 1170 940 800 1500 Direct mount Single pin mounting link Quick hitch mounting plate to operate from one double acting circuit) Direct mount Single pin mounting link Quick hitch mounting plate to operate from one double acting circuit) page 30 page 31
ENGCON COMPACTOR RF COMPACTOR Compact dimensions Interchangeable mounting plates Sideplates for levelling material and protection of vibrator unit Compact dimensions Interchangeable mounting plates MODEL COMPACTION WEIGHT LENGTH WIDTH HEIGHT COMPACTION HYDRAULIC FREQUENCY FORCE EXCL. A (MM) B (MM) C (MM) AREA (M2) FLOW (L/MIN) (HZ) MOUNTING PP350 3500 390 890 620 450 0.42 68 2100 PP600 6000 620 1050 720 520 0.58 115 2100 PP950 9500 900 1270 900 600 0.9 150 2100 MODEL EXCAVATOR WIDTH WEIGHT COMPACTION OIL FLOW CLASS (MM) FORCE REQUIRED (UP TO) (L/MIN) MAV 01 8 Ton 400 180 3500 25-70 MAV 03 17 Ton 600 380 7500 40-120 MAV 13 35 Ton 740 510 7500 40-120 MAV 14 40 Ton 850 650 14000 90-130 MAV 17 45 Ton 850 750 14000 90-130 MODEL EXCAVATOR WIDTH WEIGHT COMPACTION OIL FLOW CLASS (MM) FORCE REQUIRED (UP TO) (L/MIN) C MAV 0240 8 Ton 400 180 3500 25-75 B A MAV 0245/50 17 Ton 600 220 3500 25-75 MAV 0650 17 Ton 600 380 7500 40-120 MAV 0960 23 Ton 740 510 7500 40-120 MAV 1070 27 Ton 740 650 7500 40-120 1 x single acting circuit minimum 1 x single acting circuit minimum Hoses Flow control valve Engcon (Sweden) Hoses Flow control valve Hydraulic underhitch for removal of compactor baseplate and attachment of riddle buckets, tamper units etc. (baseplate and attachment are additional weight and price) RF Systems (Sweden) page 32 page 33
TARMAC/CONCRETE PLANER ROTARY DRUM CUTTER Swinging mounting plate ensures constant cutting depth Ideal for planing on horizontal, vertical and inclined surfaces Excellent guarding prevents material fly off Low vibration and low noise option for cutting rock, concrete, asphalt and timber Quicksnap pick retainer for quick pick changes (on some models only) MODEL PLB 200 PLB 300 PLB 450 PLB 600 STANDARD DRUMS CUT WIDTH MM 200 300 450 600 CUT DEPTH MM 0-70 0-100 0-150 0-150 TEETH (DRUM FOR CONCRETE) NR 30 (40) 36 (42) 48 (66) 60 (78) AVERAGE PLANING SPEED (1) * 30-250 40-250 80-400 80-400 (STANDARD DRUM 50% DEPTH) MIN. DISTANCE FROM PAVEMENT (MM) 40 (20*) 50 (25*) 60 (30*) 65 (30*) ROTATION ANGLE OF 120 135 130 120 THE SWINGING SUPPORT OPERATING WEIGHT 185 330 650 950 REQUIRED OIL FLOW RATE (L/MIN) 30-50 45-75 75-140 100-200 REQUIRED OIL PRESSURE (2) BAR 250-180 250-180 250-180 300-180 MODEL DRUM CUTTING OIL FLOW MAX TORQUE MAX CUTTING WEIGHT RECOMMENDED DIAMETER WIDTH (L/MIN) OUTPUT AT FORCE AT APPROX. CARRIER WEIGHT (MM) (MM) 350 BAR 350 BAR (T) (N/M) (N) SERIES ER100 307 542 50 3.115 20.3 220 3-5 SERIES ER250 400 620 90 5.2 26 450 5-15 SERIES ER 600 575 780 150 10.4 36.1 900 10-20 SERIES ER 650 575 800 200 12.5 43.5 1 15-25 SERIES ER 1200 650 850 300 23.4 72 1.55 20-40 SERIES ER 1500 S 670 1 320 23.4 69.851 1.75 25-45 SERIES ER 2000 680 1.2 350 33.5 98.529 2.2 30-50 SERIES ER 3000 805 1.33 500 46.7 116.025 3.3 45-70 SERIES ER 5000 910 1.6 700 83.5 183.516 5.5 70-110 EXCAVATOR WEIGHT (APPROX.) (3) TON 1.5-3.5 3-6 6-12 12-18 (1) Planing speed is affected by the hardness of the material to be planed, by planing depth and by the available hydraulic pressure (2) The pressure must be in inverse relation to the available flow rate and vice versa (3) The user is responsible for checking that the prime mover meets the equipments specification and weight requirements (*) On request 1 x single acting circuit (+1 x dedicated case drain line 450 & 600 models only) Mounting plate Concrete Drum Special Drums on Request Simex (Italy) 1 x single acting circuit & I x dedicated case drain line Mounting plate, hoses Vertical cutting head series ER250 ER1500 Stump grinding drum Picks choice for materials from asphalt to hard rock Erkat (Germany) page 34 page 35
MINI - MOWER FORESTRY MOWERS Weldox 700 construction for maximum durability Direct drive motor for maximum power Fits all mini and midi excavators Weldox 700 construction for maximum durability Volvo piston motors Rail approved Hydraulic front cover Mini-Forest MODEL EXCAVATOR ROTOR MOTOR CUT MATERIAL WEIGHT PRESSURE FLOW WEIGHT WIDTH DIA. (CM) (BAR) (L/MIN) RANGE (T) (CM) MODEL TO FIT CUT WIDTH MAX. MATERIAL WEIGHT REQUIRED OIL REQUIRED OIL EXCAVATOR (CM) DIAMETER PRESSURE FLOW RATE FROM (CM) (BAR) (L/MIN) TE 60 DL 1.0 tonnes 60 1 90 180 20 TFL 90 5-8 drum rotor with heavy 34cc 90 15 450 180-220 60-80 hammers piston motor TFL 100 7-10 drum rotor with heavy 40cc 100 25 690 180-220 80-100 102/80 hammers piston motor TE 80 DP 2.5 tonnes 80 5 195 180 30-55 TE 100 DP 3.5 tonnes 100 5 235 180 30-55 TE 120 DP 4.5 tonnes 120 5 265 180 30-55 TE 100 CL 5.5 tonnes 100 10 360 200-220 60-70 TE 120 CL 5.5 tonnes 120 10 415 200-220 60-70 Midi-Forest MODEL EXCAVATOR ROTOR MOTOR CUT MATERIAL WEIGHT PRESSURE FLOW WEIGHT WIDTH DIA. (CM) (BAR) (L/MIN) RANGE (T) (CM) TFM 100 10-14 drum rotor 60cc 105 30 800 230-250 100-110 with heavy 102/80 piston motor hammers 1 x single acting circuit Mounting plate Hoses Flow control valve Type E rotor (CL models only) for heavy duty applications Mechanical floating system TFM 130 10-14 drum rotor 60cc 130 30 910 230-250 100-110 with heavy 102/80 piston motor hammers TFM 160 10-14 drum rotor 60cc 160 30 1020 230-250 100-110 with heavy 102/80 piston motor hammers TFM-UX 100 10-14 fixed tool rotors 60cc 105 35 960 230-250 100-110 with reversible teeth piston motor TFM-UX 130 10-14 fixed tool rotors 60cc 130 35 1090 230-250 100-110 with reversible teeth piston motor Osma (Italy) page 36 page 37
FORESTRY MOWERS OSMA MOWERS Weldox 700 construction for maximum durability Rail approved Maxi-Forest MODEL EXCAVATOR ROTOR MOTOR CUT MATERIAL WEIGHT PRESSURE FLOW WEIGHT WIDTH DIA. (CM) (BAR) (L/MIN) RANGE (T) TFS100 15-25 drum rotor 60cc 105 35 980 230-250 120-130 350mm diameter, piston motor with heavy hammers MODEL EXCAVATOR CUT WIDTH MATERIAL WEIGHT PRESSURE FLOW WEIGHT (CM) DIAMETER (BAR) (L/MIN) RANGE (T) (CM) TE120/CP 9-14 125 10+ 475 200-220 60-75 TE160/CP 9-14 160 10+ 595 200-220 90-100 TFS130 15-25 drum rotor 60cc 130 35 1120 230-250 120-130 350mm diameter, piston motor with heavy hammers TFS160 15-25 drum rotor 60cc 160 35 1250 230-250 120-130 350mm diameter, piston motor with heavy hammers TFS-UX 100 15-25 fixed tool rotors 60cc 105 40-45 1280 230-250 150-160 with reversible teeth piston motor TFS-UX 130 15-25 fixed tool rotors 60cc 130 40-45 1380 230-250 150-160 with reversible teeth piston motor TFS-UX 160 15-25 fixed tool rotors 60cc 160 40-45 1490 230-250 150-160 with reversible teeth piston motor MODEL EXCAVATOR CUT WIDTH MATERIAL WEIGHT PRESSURE FLOW WEIGHT (CM) DIAMETER (BAR) (L/MIN) RANGE (T) (CM) LD1000 For "Spider" type 105 5+ 375 220 70-80 excavators HD1000 For "Spider" type 105 30 520 220 100-110 excavators HD1200 For "Spider" type 125 30 610 220 100-110 excavators 1 x single acting circuit minimum 1 x single acting circuit minimum Mounting plate Hoses Digital revolution counter kit Osma (Italy) Mounting plate Hoses Piston motor Rotor type E (TE120CP only) for heavy duty applications Mechanical floating link (TE/CP models only) Open rotor (HD models only) Digital revolution counter kit Osma (Italy) page 38 page 39
STUMP PLANER TREE SHEAR 3 blade design for optimum cutting performance Designed for use with Mini-Auger and Auger Torque auger drive units (contact Exac-One for info on suitable drive units) Models SP200 200mm diameter 500mm long SP250 250mm diameter 500mm long SP350 350mm diameter 500mm long SP500 500mm diameter 500mm long Manufactured from 26mm high tensile steel Single 32mm blade eliminates complicated adjustments and maintenance Unique serrated jaw holds tree during cutting cycle 110 degree hydraulic rotation Cut or trim standing trees up to 350mm diameter Cut fallen trees into firewood Can be used as grab for re-handling cut timber MODEL TIMBERLINE 350 TIMBERLINE 250 HYDRAULIC DRIVEN HYDRAULIC DRIVEN BLADE TYPE SINGLE BLADE SINGLE BLADE (30 MM MINIMUM THICKNESS) (25 MM MINIMUM THICKNESS) MAXIMUM ROTATION 110 DEGREES 110 DEGREES MAXIMUM MATERIAL THICKNESS AT 190 BAR 350 MM 250 MM MAXIMUM OIL PRESSURE 205 BAR 205 BAR EQUIPPED WITH A SERRATED TOOTH HOLDING DEVICE YES YES ABILITY TO SHARPEN BLADE WITHOUT REMOVING YES YES CYCLE TIME AT 90 LPM 4.5 SECONDS 4.5 SECONDS WEIGHT 567 KG 255 KG CYLINDER TYPE WELDED WELDED CYLINDER BORE 130 MM 85 MM CYLINDER ROD 75 MM 50 MM CYLINDER PORTS 15 MM 15 MM VALVE PORTS 15 MM 15 MM PIN TYPE 36 MM CHROMED 36 MM CHROMED CLEVIS TYPE EXTRA HEAVY DUTY EXTRA HEAVY DUTY LENGTH DIM A (MM) 1400 1350 WIDTH DIM B (MM) 1250 1000 HEIGHT DIM C (MM) 680 550 1 x single acting circuit Mini-Auger Auger Torque Auger Torque (England) 2 pin mounting bracket (to suit direct mount or quick hitch) Mini-Mower Osma Range Forestry Range Sidney Manufacturing Inc (USA) page 40 page 41
STEEL SHEAR CONCRETE PULVERISOR Hardox construction for maximum durability Compact dimensions Hardox construction for maximum durability Compact dimensions MODEL SCR 250 EXCAVATOR WEIGHT (TONNES) 2.5-6.0 WEIGHT IN WORKING CONDITIONS 250 A (MM) 236 B (MM) 230 L1 (MM) 820 L2 (MM) 1050 CYLINDER FORCE (TONNES) 26 X @ 21O (BAR) 62 Y @ 21O (BAR) 30 Z @ 21O (BAR) 20 WORKING PRESSURE (BAR) 210 ROTATION HYDRAULIC 360 Hydraulic rotation Mounting plate Hoses to operate from one double acting circuit) Concrete pulverisor Socomec (Italy) MODEL PDO 200 PDO 300 PDO 650 WEIGHT IN WORKING CONDITIONS 200 300 650 A (MM) 300 360 500 B (MM) 300 355 410 C (MM) 80 80 160 D (MM) 1130 1240 1515 E (MM) 25 30 35 CYLINDER FORCE (TONNES) 20 30 50 CRUSHING FORCE (TONNES) 15 22 35 CUTTER FORCE (TONNES) 40 70 100 MAX. PRESSURE (BAR) 200 250 280 WORKING PRESSURE (BAR) 180 230 250 OIL FLOW (L/MIN) 30 50 60 ROTATION HYDRAULIC 360 ROTATION PRESSURE (BAR) 200 250 140 ROTATION OIL FLOW (L/MIN) 30 50 15 EXCAVATOR WEIGHT (TONNES) 1.7-3 3-6 6-13 Hydraulic rotation Mounting plate Hoses to operate from one double acting circuit) Steel shear Socomec (Italy) page 42 page 43
ROTARY SCREENING BUCKET MINI - AUGER Hardox screens for maximum durability Rotary screening action Shallow pitch auger flights ensure maximum soil removal Shock Lock system increase life of Tungsten Teeth Augers manufactured using heavy wall tubing for maximum durability MODEL SBV 300 SBV 400 SBV 800 SBV 1350 SBV 1650 SBV 1950 EXCAVATOR WEIGHT (TONNES) 3-5 5-8 8-12 13-17 16-22 22-32 WEIGHT IN WORKING 280 410 820 1350 1650 1950 CONDITION A (MM) 445 515 690 770 810 810 B (MM) 720 945 940 1300 1450 1650 C (MM) 990 1175 1340 1680 1760 1800 D (MM) 680 790 900 1170 1340 1560 L (MM) 700 800 900 1200 1400 1600 SAE CAP (CUBIC METRE) 0.2 0.3 0.4 0.7 0.85 1 WORKING PRESSURE (BAR) 100-120 100-120 100-120 100-120 100-120 100-120 OIL FLOW (L/MIN) 30-50 30-50 50-70 80-100 80-100 80-100 MODEL 1200 X 2500 3500 Max 5500 Max 7000 OUTPUT SHAFT SIZE (MM) 50 65 65 57 57 OUTPUT SHAFT SHAPE (MM) Round Round Round Square Square EXCAVATOR WEIGHT (TONNES) 0.75-1.2 2-3.5 2.5-4.5 4.5-7 5-8 AUGER RANGE S2 S4 S4 S5 S5 DRILLING DIAMETER (MM) 100-300 100-500 100-600 100-750 100-900 MAX. TORQUE (NM) 1189 2452 3643 5667 7170 MAX. PRESSURE (BAR) 185 205 240 240 240 REQUIRED OIL FLOW (L/MIN) 15-32 37-65 40-95 50-114 60-135 HYDRAULIC HOSES 1/2" BSP 1/2" BSP 1/2" BSP 1/2"BSP 1/2" BSP WEIGHT 35 54 66 83 97 RPM 18-24 18-24 18-24 18-24 18-24 18-24 HYDRAULIC CONNECTORS 1/2" 1/2" 3/4" 3/4" 3/4" 3/4" Mounting plate Hoses Material grading options through interchangeable screens Socomec (Italy) P.T.O. for more information page 44 page 45
CHAIN TRENCHER DIGA - BARA Spring loaded trench cleaner Chain options for different trench widths and ground conditions Models T600 (600mm dig depth) T900 (900mm dig depth) Mechanical tip no hydraulics Attaches to excavator in seconds using single pin Skip lock release lever operated by excavator bucket Virtually maintenance free Standard models to suit excavators up to 2 tonnes Easily transportable on trailer or pick up Models 1150 (1150mm wide) 1300 (1300mm wide) 1400 (1400mm wide) Specification Width (see models) (a) Overall length 2170mm (c) Height 1020mm (b) Skip Length 1000mm (d) Skip depth 400mm Max gross weight 600kg Lifting Eye (e) D B E Nil Single pin mounting kit Larger models custom built to order only C A 1 x single acting circuit minimum Requires 40l/m at 150 Bar J C Engineering (England) 2 pin mounting bracket (to suit direct mount or quick hitch) 150/100mm General Purpose Earth / Tungsten chain (Cuts 150mm trench as supplied when spacers are removed cuts 100mm trench) 150/100mm earth chain 150/100mm tungsten chain 200mm earth chain 200mm Tungsten chain Auger Torque Ltd (England) page 50 page 51
KERB - KARRY RAIL ATTACHMENTS Attaches to excavator in seconds using single pin Virtually maintenance free. Standard models to suit excavators up to 10 tonnes Easily transportable MODEL A B C D E F G MAX. GROSS PACKS OF (MM) (MM) (MM) (MM) (MM) (MM) (MM) WEIGHT STD. KERBS CARRIED KERB-KARRY 20 1650 925 1350 300 660 900 380 2000 1 KERB-KARRY 40 1700 925 2390 300 660 550-1150 380 3500 2 We offer an extensive range of attachments for rail applications Please contact us for further information Models PFS-80/C Hydraulic Tamper unit PFS-55/TL Railway Sleeper grab (medium duty) PFS-55/TP Railway Sleeper grab (heavy duty) PFS-70/R Railway Track grab (medium duty) PFS-140/R Railway Track grab (heavy duty) Clamshell Buckets for Wet Bedding Single pin, two pin or dedicated coupler mounting options PFS-70/R PFS-55/TL PFS-80/C Nil Single pin mounting kit Kerb-Grip Kerb-Krawler System BMV-2/250 page 52 page 53
HEAVY DUTY RAKES RIPPER Range of heavy duty rakes to suit excavators from 1 tonne to 28 tonnes. Manufactured to customers own specification from Hardox 400. Range of rippers to suit excavators from 1 tonne to 80 tonnes. Manufactured from Hardox 400 to suit either quick hitch or direct mount applications. MACHINE WEIGHT (TONNES) All rakes are made to customers requirements. 1-2 2-4 4-8 9-14 15-19 20-28 LEG MATERIAL 25mm HARDOX 25mm HARDOX 30mm HARDOX 30mm HARDOX 40mm HARDOX 40mm HARDOX Price will depend on Dim D and the number of legs required. MODEL MACHINE DIM A (MM) SHANK TOOTH WEIGHT (TONNES) MATERIAL SYSTEM R10 1-2 300 25mm Hardox 400 Cat 428 R30 3-4 500 30mm Hardox 400 Cat 428 R40 4-7 600 40mm Hardox 400 Cat 205 (J250) R70 7-9 600 40mm Hardox 400 Cat 205 (J250) R90 9-10 750 50mm Hardox 400 Cat 215 (J300) R130 13-15 750 50mm Hardox 400 Cat 225 (J350) R160 16-19 750 60mm Hardox 400 Cat 225 (J350) R200 20-27 900 60mm Hardox 400 Cat 235 (J460) R280 28-37 900 80mm Hardox 400 Cat 245 (J550) R380 38-48 900 100mm Hardox 400 Cat 245 (J550) Nil A Nil Manufactured By Abiljo, England Abiljo, England page 54 page 55
PALLET FORKS Range of mounted pallet forks to suit excavators from 2 tonnes to 12 tonnes and with capacities from 500kgs to 1500kgs. The fork carriage design allows for quick sideways adjustment of individual forks or for their complete removal. MODEL DIM A DIM B DIM C DIM D DIM E WEIGHT CAPACITY (MM) (MM) (MM) (MM) (MM) FK5 800 850 80 405 900 110 500 FK6 800 1100 80 405 920 130 600 FK10 1000 1200 80 405 970 140 1000 FK15 1100 1350 100 405 1050 197 1500 FK15R (reinforced) 1100 1350 100 405 1050 227 1500 B D E C A Mounting plate Nil Nil Nil Cangini page 56 page 57