HOESCH FLSHINGS ND CCESSOIRES SOUTH TECHNICL INFORMTION GermanEngineered
Contents Roof and wall connections 6 General..............................................................6 Hoesch isodach mono and isorock integral D................... 11 Wall connections 13 General............................................................ 13 Hoesch Planeel siding............................................ 19 Concealed fastening............................................... 20 Top hats........................................................... 24 Hoesch isowand integral with FSI window system............... 28 Roof connections 30 General............................................................ 30 Covered attachment............................................... 35 Hoesch rched Roof.............................................. 37 Hoesch Roof System 2000........................................ 38 Flashings for floors and ceilings 39 Hoesch dditive Floor............................................ 39 Suspended ceilings for cold store panels.......................... 40 ccessories 41 Profile filler........................................................ 41 Sealing materials.................................................. 42 Sealing materials and installation aids............................ 43 Special flashings 44 General............................................................ 44 Round Gutter System 45 Z33-100_ Eaves gutter............................................ 46 Z33-101_ End item................................................ 46 Z33-102_ Gully.................................................... 46 Z33-103_ Conical gully............................................ 47 Z33-104_ S-offset (top)........................................... 47 Z33-105_ Expansion basket....................................... 47 Z33-106_ Downpipe............................................... 48 Z33-107_ Downpipe bracket...................................... 48 Z33-108_ S-offset (bottom)....................................... 48 Z33-109_ Outlet bend............................................. 49 Z33-110_ Eaves gutter bracket.................................... 49 Z33-900_ Eaves gutter bracket.................................... 49 Z33-901_ Eaves gutter bracket.................................... 50 2
ngular gutter system 51 Z33-111_ ngular gutter.......................................... 52 Z33-112_ Gutter junction......................................... 52 Z33-113_ Cage.................................................... 52 Z33-114_ Square inlet............................................. 53 Z33-115_ Downpipe square....................................... 53 Z33-902_ Offset square top elbow.............................. 53 Z33-117_ Sleeve square.......................................... 54 Z33-116_ Outlet bend square..................................... 54 Z33-118_ Stop end................................................ 54 Z33-120_ Bracket................................................. 55 Z33-905_ Prefabricated angle gutter / gable...................... 55 Z33-903_ Elbow gutter positive, negative....................... 56 Z33-904_ Transformer item from square to round................. 56 Z33-119_ Square inlet............................................. 57 Insulated Rainwater System 58 Z33-906_, Z33-907_ Insulated gutter........................................................................................................... 58 Z33-908_, Z33-909_ Insulated gutter........................................................................................................... 59 Z33-910_, Z33-911_ Insulated gutter........................................................................................................... 60 Z33-912_, Z33-913_ Insulated gutter........................................................................................................... 61 Locksmith components 62 K43-125_ and K43-126_ U profile.............................................................................................................. 62 K43-127_ Plinth profile......................................................................................................................... 62 K43-128_ and K43-129_ syetrical ngle.................................................................................................. 63 K43-130_ Syetrical ngle.................................................................................................................. 63 Z33-9141 Snow fence.......................................................................................................................... 64 Z33-9151 Snow fence type Snowking.......................................................................................... 64 Passage Piping Packing 65 Z33-121_ Dektite............................................................................................................................. 65 Z33-122_ Dektite Soaker...................................................................................................................... 65 Z33-123_ Dektite Retrofit..................................................................................................................... 66 Z33-124_ Dekstrip Flashing................................................................................................................. 66 3
Flashings and accessories From ngle bracket to Z-profile Standard flashings Flashings which are frequently used for structures are offered as standard flashings. Their geometry, material thickness and coating which are adapted to suit the Hoesch building elements are represented in this brochure. Standard flashings may be ordered simply by indicating their part number, without any need for a sketch. In a particular case items such as angles may be required. Unless otherwise stated in the specification, standard flashings have a length of 6000. * Forms for stretches can be downloaded and printed from our website www.hoesch-bau.com Customised flashings Flashings produced according to the customer s specification are customised flashings. These special flashings are ordered by supplying a sketch. This sketch should contain all data relating to dimensions, angles and the nature of the coating. Dimensions should always be internal dimensions. The maximum length that can be produced is 8000.* For ion possibilities and supply, delivery dates, coatings, colours, minimum quantities and prices, please contact us. Please note the information on page 40 (possibilities of folding) and page 41 (stock material). Base material This is steel sheet as per DIN EN 10 147. This material is available with the following processing properties: steel sheet with a Z 275 coating, zinc layer 275 g/m² on both sides steel sheet with GLFN Z 255 coating, layer thickness 255 g/m² on both sides (95 % Zn, 5 % l) steel sheet with GLVLUME Z 185 coating, layer thickness 185 g/m² on both sides (55 % l, 43.4 % Zn, 1.6 % Si) steel sheet with ZM EcoProtect 130 coating, layer thickness 130 g/m² on both sides (>98 % Zn, 1 % Mg) 0.75 unless otherwise specified for logistic, structural or constructional reasons. Using the standard material thickness, overlapping in the joint area is made easier. Standard overall length 6000 unless otherwise specified for a flashing (max. 8000 ). This also applies to cover and corner profiles which are cut to length and made ready to fit on site. Coatings When ordering, please indicate surface finish of sides and B respectively. The side is always the visible side. Higher corrosion protection categories can be achieved depending on the chosen coating. Flashings can also be supplied from coil coated material or individually printed. 4
Ordering examples: = SP RL 9001 B = (RSL) or = PVDF RL 9001 B = (RSL) or + B individually printed in a custom colour For coil coating, please see the ThyssenKrupp Steel Europe colour chart for available types and colours of coatings. For individual piece painting, RL colour shades or special colours are available; please contact us for information on colours available. The coating system chosen for the visible side of flashings must correspond to that of the elements for roof and wall, if the same colour is used. In the case of special colours, it may be necessary to use the same batch. Please take this into account when placing your order. Installation In normal industrial construction flashings can be fitted in such a way that they overlap. ny return folds and folded edges of flashings must be notched on site. Overlapping joints must be sealed during installation using amino hardening sealants with a silicone base. Dimensions and tolerances ll dimensions of our standard flashings are internal dimensions unless otherwise indicated on the drawings. The cross sectional tolerances are ± 2 (up to 2 material thickness). Load-bearing structural flashings are made from at least S280GD. The thickness tolerances correspond to those of the base material, i.e. to DIN EN 10 143. 5
Roof and wall connections General Parapet flashing 1 (part 1) 0.75 Girth Girth Weight Suitable for C D E kg/m K40-131 54 80 90 246 1.5 K40-132 81 115 125 308 1.9 K40-133 79 160 170 351 2.1 Sandwich panels, Trapezoidal profiles Bracket 1 (part 2) 1,50 Girth Development Weight Suitable for kg/m K70-081 64 104 1.2 Sandwich panels, K70-082 209 249 3.0 Trapezoidal profiles Parapet flashing 2 (part 1) 0.75 Girth Development Weight Suitable for C D E Product Element thick. kg/m K40-121 40 11 110 308 1.8 80 Sandwich K40-122 50 13 200 410 2.5 170 panels K40-123 60 15 270 492 3.0 240 Bracket 1 (part 2) 1.50 Girth Development Weight Suitable for kg/m K70-081 64 104 1.2 K70-082 209 249 3.0 Sandwich panels When ordering, please indicate the pitch angle of the roof α. Range: 3 < α < 30 Verge flashing (monopitch roof) 1.00 32 15 Dimension E Development Weight Suitable for kg/m K30-081 140 410 3.3 Sandwich elements K30-082 225 492 3.9 6
Verge flashing (monopitch roof) 2 (part 1) 1,00 Part 1 Roof pitch (α) Development Weight Suitable for Degrees kg/m K40-041 5 K40-042 10 554 4.4 Sandwich panels Part 2 Parapet 1.00 Girth Development Weight Suitable for B kg/m K40-141 100 62 412 3.3 K40-142 120 42 412 3.3 K40-143 140 72 462 3.7 K40-144 160 52 462 3.7 Hoesch Trapezoidal profiles and Sandwich panels 190 20 40 60 45 155 120 B B Bracket 2 (part 2) 1.50 Coating Development Weight Suitable for kg/m K70-041 Manufacturer's 5 roof pitch 249 3.0 K70-042 choice 10 roof pitch Verge flashing 1 1.00 Girth Development Weight Suitable for D E kg/m K30-071 163 154 461 3.7 K30-072 379 370 677 5.4 K30-073 522 513 820 6.6 K30-074 194 185 492 3.9 K30-075 317 308 615 4.9 Hoesch Trapezoidal profiles and Sandwich panels 7
Verge flashing 2 1.00 Part 2 Part 1 Girth Development Weight Suitable for E kg/m K40-031 295 554 4.4 K40-032 151 410 3.3 K40-033 233 492 3.9 K40-034 356 615 4.9 K40-035 479 738 5.9 Hoesch Trapezoidal profiles and Sandwich panels Bracket 3 (part 2) 1.50 Coating Development Weight Suitable for kg/m K70-031 Manufacturer's choice 249 3.0 Hoesch Trapezoidal profiles and Sandwich panels ngle 1.50 Girth Development Weight Suitable for C D kg/m K33-011 75 103 178 2.1 K33-012 50 106 156 1.9 K33-013 140 171 311 3.7 K33-014 65 143 208 3.3 fastening of Sandwich panels at the roof edge Internal ridge flashing (roof to wall junction) 15 α max. 6000 Girth Suitable for K33-1051 170 all Sandwich panels Internal (concave) corner flashing (eave roof to wall junction) max. 6000 15 B 15 α Girth Girth Suitable for B K33-1091 50 30 110 K33-1092 60 40 130 all Sandwich panels K33-1093 80 50 160 *Customer to specify: roof pitch α, length, quantity, colour and coating 8
External (concave) without brackets corner flashing (eave to wall junction) max. 6000 Element thickness d Girth K33-1071 75 143 K33-1072 95 163 K33-1073 115 183 K33-1074 130, 135 203 K33-1075 150, 155 223 K33-1076 200 273 Suitable for all Sandwich panels 23 25 d+40 d-5 15 α d External concave without brackets corner flashing (eave to wall junction) max. 6000 Grith Grith K33-1161 60 140 K33-1162 80 160 K33-1163 100 180 K33-1164 120 200 Suitable for all Sandwich panels Structural edge angle 1.00 Girth Development Weight Suitable for D kg/m K30-251 407 492 4.0 K30-252 530 615 4.9 Hoesch Trapezoidal profile Lean to flashing (flat roof to wall junction) 1.00 Girth Development Weight Suitable for D kg/m K30-171 152 410 3.3 K30-172 357 615 4.9 K30-173 203 461 3.7 K30-174 234 492 3.9 K30-175 296 554 4.4 K30-176 270 528 4.2 Hoesch Trapezoidal profiles and Sandwich panels * Customer to specify: roof pitch α, length, quantity, colour and coating 9
55 56 When ordering, please indicate the pitch angle of the roof. Range: 3 < α < 30 Lean to flashing (mono-pitch roof to wall junction)* 1,50 Girth Development Weight Suitable for D kg/m K30-161 152 410 3.3 K30-162 234 492 3.9 K30-163 203 461 3.7 Hoesch Trapezoidal profiles and Sandwich panels 20 Wall levelling piece α α α 25 α=135 0.75 20 45 Development Weight Suitable for kg/m K30-501 176 1.1 Hoesch Trapezoidal profiles and Sandwich panels *Customer to specify: roof pitch α, length, quantity, colour and coating 10
Roof and wall connections Hoesch isodach mono, Hoesch isorock integral D Verge flashing 3 (part 1) 1.00 Dimension Development Weight Suitable for B C D E kg/m K33-041 280 33 100 50 120 K33-042 190 20 200 28 130 615 4.9 Hoesch isodach mono, Hoesch isorock integral D Bracket 3 (part 2) Coating 1.50 Manufacturer s choice Development Weight Suitable for kg/m K70-031 249 3.0 K33-042, Hoesch isorock integral D K73-021 356 4.2 K33-041, Hoesch isodach mono Mono ridge flashing* max. 6000 Dimension Girth K43-1031 270 600 K43-1032 300 630 K43-1033 330 660 Suitable for all sandwich elements 175 K43-1034 312 677 all sandwich elements > 175 90 (105) 85 (105) 160 100 - α 100 50 75 15 15 α Verge flashing** max. 6000 Dimension Girth K33-1131 270 600 K33-1132 300 630 K33-1133 330 660 Suitable for all sandwich elements 175 K33-1134 312 677 all sandwich elements > 175 90 (105) 85 (105) 160 100 100 50 75 15 15 Zed verge flashing** max. 6000 25 25 Dimension Girth Suitable for K33-1411 35 85 all sandwich elements * Customer to specify: roof pitch α, length, quantity, colour and coating **Customer to specify: length, quantity, colour and coating 11
Verge flashing 4 1.00 Dimension Development Weight Suitable for B C D E kg/m K33-051 180 33 100 50 120 554 4.4 Hoesch isodach mono, Hoesch isorock integral D K33-052 140 20 200 28 140 615 4.9 175 K33-056 230 20 200 28 112 677 5.4 Hoesch isorock integral D > 175 When ordering, please indicate the pitch angle of the roof. Range: 3 < α < 30 Verge flashing (monopitch roof) 3 1,00 Dimension ngle Development Weight B C D E β Grad kg/m K33-054 140 20 200 28 140 150 + α 615 4.9 Suitable for Hoesch isorock integral D 175 K33-058 230 20 200 28 112 150 + α 677 5.4 Hoesch isorock integral D > 175 Verge flashing (flat roof to wall junction) (version 2) 1.00 Dimension Development Weight Suitable for B C D kg/m K33-071 33 120 50 99 K33-072 20 140 28 95 461 3.7 Hoesch isodach mono Hoesch isorock integral D When ordering, please indicate the pitch angle of the roof. Range: 3 < α < 30 Verge flashing monopitch roof to a wall junction (version 2) 1.00 Dimension ngle Development Weight Suitable for B C D β Grad kg/m K33-074 20 140 28 95 90 + α 461 3.7 Hoesch isorock integral D 12
Wall connections General External corner flashing, syetrical 0.75 Building construction (HB) 0.60 Cold store construction (KHB) Building construction 5000 (max. 6000 ) Cold store construction Dimension Development Weight E HB Weight KHB kg/m kg/m K40-101 110 246 1.5 1.2 K40-102 50 137 0.8 0.7 K40-103 190 410 2.4 2.0 K40-104 260 554 3.3 2.7 K40-105 80 205 1.2 1.0 K40-106 160 351 2.1 1.7 K40-107 100 246 1.5 1.2 K40-108 140 308 1.8 1.5 Suitable for sandwich elements, Hoesch Trapezoidal profiles External corner flashing, asyetrical 0.75 Building construction (HB) 0.60 Cold store construction (KHB) Building construction 5000 (max. 6000 ) Cold store construction Dimension Development Weight C HB Weight KHB kg/m kg/m K40-111 190 308 1.9 1.5 K40-112 230 351 2.1 1.7 K40-113 140 258 1.5 1.2 K40-114 80 205 1.2 1.0 K40-115 120 238 1.4 1.1 K40-116 160 284 1.7 1.4 K40-117 210 330 2.0 1.6 Suitable for sandwich elements, Hoesch Trapezoidal profiles Connection profile 0.75 Dimension Radius ngle Development Weight Suitable for B C D E R β Grad kg/m K01-012 41 35 33 232 ca. 2 126 308 1.8 K01-013 42 35 40 231 ca. 2 107 308 1.8 K01-014 59 40 50 313 12 121 410 2.5 Hoesch Trapezoidal profile T35.1 Hoesch Trapezoidal profile T40.1 Hoesch Trapezoidal profile T50.1 β 13
External corner flashing 0.75 Girth ngle Development Weight Suitable for B C α Grad kg/m K41-021 119 41 30 127 381 2.3 Hoesch Trapezoidal profile T35.1 K41-022 119 42 31 107 383 2.3 Hoesch Trapezoidal profile T40.1 K41-023 135 58 37 122 461 2.8 Hoesch Trapezoidal profile T50.1 External concave corner flashing* 20 28 30 28 20 30 45 max. 6000 Girth Girth K43-1001 70 296 K43-1002 100 356 K43-1003 150 456 Suitable for all Sandwich panels External corner flashing, polygonal 0.75 6000 Development Weight Execution Suitable for kg/m K43-152 410 2.5 polygonally folded radius Hoesch isowelle Fasten using Z43-101 spacers. Spacer 1.50 Colour RL 9002 Development Weight Suitable for kg/m Z43-101 230 0.135 fastening flashings to Hoesch isowelle Inner corner flashing, round 0.60 Cold store construction max. 4000 Development Weight Suitable for kg/m K40-171 88 0.4 Sandwich panels * Customer to specify: length, quantity, colour and coating 14
Inner corner flashing, syetrical 0.75 Building construction (HB) 0.60 Cold store construction (KHB) Building construction 5000 (max. 6000 ) Cold store construction Girth Development Weight E HB Weight KHB kg/m kg/m K40-091 90 205 1.2 1.0 K40-092 50 123 0.7 0.6 K40-093 140 308 1.8 1.5 K40-094 40 112 0.7 0.5 K40-095 60 154 0.9 0.7 K40-096 80 205 1.2 1.0 K40-097 100 246 1.5 1.2 Suitable for Sandwich panels Flat metal sheet 0.75 Building construction (HB) 0.60 Cold store construction (KHB) Building construction 5000 (max. 6000 ) Cold store construction Girth Development Weight Suitable for B HB KHB kg/m kg/m K00-041 50 19 88 0.5 0.4 K00-042 60 14 88 0.5 0.4 K00-043 80 12 103 0.6 0.5 K00-044 100 12 123 0.7 0.6 K00-045 120 17 154 0.9 0.7 Sandwich panels K00-046 140 18 176 1.1 0.8 K00-047 70 16 103 0.6 0.5 K00-048 90 11 112 0.7 0.5 Edge flashing 0.75 Building construction (HB) 0.60 Cold store construction (KHB) Building construction 5000 (max. 6000 ) Cold store construction Girth Development Weight Suitable for B HB KHB Product Element thickness kg/m kg/m K40-181 42 11 123 0.7 0.6 40 K40-182 62 16 154 0.9 0.7 60 K40-183 82 17 176 1.1 0.8 80 K40-184 102 21 205 1.2 1.0 100 K40-185 122 11 205 1.2 1.0 120 K40-186 142 22 246 1.5 1.2 140 K40-187 152 17 246 1.5 1.2 150 Sandwich K40-188 162 12 246 1.5 1.2 160 panels K40-189 172 20 273 1.6 1.3 170 K40-196 177 18 273 1.6 1.3 175 K40-191 182 16 273 1.6 1.3 180 K40-192 202 11 284 1.7 1.4 200 K40-193 222 13 308 1.8 1.5 220 K40-194 52 12 137 0.8 0.7 50 K40-195 72 11 154 0.9 0.7 70 15
Cover and edge flashing 0.75 Girth Development Weight Suitable for C D Product Element thickness kg/m K40-071 40 41 137 0.8 40 K40-072 40 61 154 0.9 60 K40-073 40 67 176 1.1 66 K40-074 40 81 176 1.1 80 K40-075 40 97 205 1.2 96 K40-076 40 101 205 1.2 100 K40-077 35 121 205 1.2 120 K40-078 40 141 246 1.5 140 Sandwich K40-079 40 151 246 1.5 150 panels K40-201 40 161 273 1.6 160 K40-202 40 171 273 1.6 170 K40-208 40 176 273 1.6 175 K40-203 40 181 284 1.7 180 K40-204 40 201 308 1.8 200 K40-205 40 221 320 1.9 220 K40-206 40 51 154 0.9 50 K40-207 40 71 176 1.1 70 U profile 1.50 Building construction 5000 (max. 6000 ) Cold store construction Girth Development Weight Suitable for Product Element thickness kg/m K43-091 41 101 1.2 40 K43-092 61 121 1.5 60 K43-093 81 141 1.7 80 K43-094 101 161 1.9 100 K43-095 121 181 2.2 Sandwich 120 K43-096 141 201 2.4 panels 140 K43-097 151 211 2.5 150 K43-098 171 231 2.8 170 K43-100 176 236 2.8 175 K43-099 201 261 3.1 200 U profile 1.50 Girth Development Weight Suitable for C D E Product Insulation thickness kg/m K00-011 128 40 40 208 2.5 40 K00-012 149 50 50 249 3.0 50 K00-013 129 60 60 249 3.0 Hoesch 60 K00-014 119 70 60 249 3.0 Trapezoidal 70 K00-015 109 80 60 249 3.0 profile 80 K00-016 161 90 60 311 3.7 90 K00-017 151 100 60 311 3.7 100 16
Z profile 1.50 Girth Development Weight Suitable for C D Product Insulation thickness kg/m K00-021 56 40 156 1.8 40 K00-022 46 50 156 1.8 50 K00-023 58 60 178 2.1 60 Hoesch K00-024 48 70 178 2.1 70 Trapezprofil K00-025 68 80 208 2.5 80 K00-026 58 90 208 2.5 90 K00-027 48 100 208 2.5 100 Drip flashing 1 0.75 Girth Development Weight Suitable for Element C D E Product thickness kg/m K40-081 45 52 62 154 0.9 Sandwich 40 K40-082 47 72 82 176 1.1 panels 60/66 K40-083 118 31 40 205 1.2 K40-084 144 46 55 246 1.5 K40-085 134 56 65 246 1.5 K40-086 56 92 102 205 1.2 Hoesch Trapezoial profiles K40-087 77 112 122 246 1.5 96/100 Sandwich K40-088 57 132 142 246 1.5 120 panels K40-089 64 152 162 273 1.6 140 K40-080 55 172 182 284 1.7 160 K40-151 116 100 110 273 1.6 K40-152 48 100 110 205 1.2 K40-153 107 120 130 284 1.7 K40-154 69 120 130 246 1.5 K40-155 109 81 90 246 1.5 K40-156 68 81 90 205 1.2 K40-157 89 162 172 308 1.8 Hoesch isowelle 150 K40-158 112 182 192 351 2.1 170 K40-159 102 192 202 351 2.1 180 K40-150 100 212 222 369 2.2 200 K40-1001 62 72 50 K40-1002 82 92 70 alle 80 84 104 Expension joint flashing* max. 6000 Girth Girth K43-1011 75 230 K43-1012 85 250 K43-1013 100 280 K43-1014 110 300 Suitable for all Sandwich panels 15 25 25 15 60 * Customer to specify: length, quantity, colour and coating 17
Convex flashing (vertical junction)* max. 6000 28 30 15 15 135 28 30 Grith Grith K43-1081 30 176 K43-1082 40 186 K43-1083 50 196 Suitable for all Sandwich panels Top hat flashing (with even snap on corner cap)** max. 6000 26 1 15 26 25 15 24 Grith Grith K43-1131 35 178 K43-1132 40 188 K43-1133 80 268 Suitable for all Sandwich panels Top hat flashing (with recessed snap on cover cap)** max. 6000 26 1 26 15 15 15 24 Grith Grith K43-1141 35 178 K43-1142 40 188 K43-1143 80 268 Suitable for all Sandwich panels 18 * Customer to specify: length, quantity, colour and coating ** Customer to specify: lenght, quantity, colour and coating (PES0,6)
Wall connections Hoesch Planeel Siding Carrier rail & butt strap 1,50 28,5 52 Coating GLVLUME Product Hoesch Planeel Siding 110 () Suitable for carrier rail Z40-013 3994 Hoesch Planeel Siding butt strap Z40-021 500 Hoesch Planeel Siding 75 100 butt strap Z40-021 3994 Starter bar starter bar K44-011 max. 4000 Development Weight Suitable for kg/m K44-011 95 0.64 Hoesch Planeel Siding Material length and coating to match the Hoesch Planeel Siding order. Joint cover - Blanking profile Carrier rail max. 4000 Development Weight Suitable for kg/m K44-021 56 0.45 Hoesch Planeel Siding Type, material lenght and coating are completetd according to the order Hoesch Planeel Siding. Joint cover - Top hat max. 4000 20 Development Weight Suitable for kg/m K44-031 98 0.78 Hoesch Planeel Siding Type, material lenght and coating are completetd according to the order Hoesch Planeel Siding. Joint cover - T profile max. 4000 Development Weight Suitable for kg/m K44-041 150 1.20 Hoesch Planeel Siding 50 Type, material lenght and coating are completetd according to the order Hoesch Planeel Siding. 19
Wall connections Concealed fastening Horizontal drip flashing 2 0.75 Girth Development Weight Suitable for B Product Element thickness kg/m K43-011 30 51 176 1.1 K43-012 50 60 205 1.2 80 K43-013 70 81 246 1.5 100 K43-014 90 61 246 1.5 120 K43-015 110 68 273 1.6 140 K43-016 130 59 284 1.7 160 Sandwich K43-017 150 63 308 1.8 180 panels K43-018 170 86 351 2.1 200 K43-019 190 66 351 2.1 220 K43-201 120 69 284 1.7 150 K43-202 140 73 308 1.8 170 K43-203 40 70 205 1.2 70 K43-204 145 68 308 1.8 175 60 B Horizontal drip flashing isowand integral FSI B 0.75 32 22 115 45 11 155 90 Girth Development Weight Suitable for B Product Element thickness kg/m K43-041 45 66 176 1.0 K43-042 65 75 205 1.2 isowand integral 80 K43-043 85 55 205 1.2 with 100 K43-044 105 76 246 1.5 FSI windows 120 K43-045 115 66 246 1.5 140 60 Horizontal drip flashing isowand integral B B 0.75 32 115 45 11 37 155 90 Girth Development Weight Suitable for B Product Element thickness kg/m K43-181 45 51 176 1.1 K43-182 65 60 205 1.2 isowand integral 80 K43-183 85 81 246 1.5 100 K43-184 105 61 246 1.5 120 K43-185 115 51 246 1.5 140 60 20
Base profile 1.50 Building construction max. 4000 Cold store construction Girth Development Weight Suitable for C kg/m K43-021 49 77 0.9 K43-022 97 125 1.5 K43-023 150 178 2.1 K43-024 221 249 3.0 Hoesch isowand integral, Hoesch isorock vario vertically laid and Hoesch isorock Base profile for horizontally laid panels 1.50 Coating side: 25 µm (standard PLDUR SP RL 9002) B side: RSL, colour Manufacturer's choice Girth ngle Weight Suitable for Development C D E Product Element thickness Degrees kg/m K43-061 42 63 20 90 125 1.5 Hoesch isowand integral 60 K43-062 29 55 20 90 104 1.2 Slit panel all K43-063 62 74 20 90 156 1.8 Hoesch isowand integral 80 K43-064 82 76 20 90 178 2.1 Hoesch isowand integral 100 K43-065 53 110 15 92 178 2.1 Hoesch isowelle 84 Hoesch isowand vario 80 K43-066 33 108 15 94 156 1.8 Hoesch isowand vario 60 K43-067 73 90 15 92 178 2.1 Hoesch isowelle 104 Hoesch isowand vario 100 K43-068 102 56 20 90 178 2.1 Hoesch isowand integral 120 K43-071 93 100 15 91 208 2.5 Hoesch isowand vario 120 K43-072 113 121 15 91 249 3.0 Hoesch isowand vario 140 K43-073 122 107 20 90 249 3.0 Hoesch isowand integral 140 21
Base profile for horizontally laid panels Coating 1.50 side: 25 µm (standard: PLDUR SP RL 9002) B side: RSL Girth Development Weight Suitable for Element C D E Product thickness kg/m K43-141 55 110 178 2.1 80 K43-142 75 120 208 2.5 100 K43-143 95 100 208 2.5 120 K43-144 115 121 249 3.0 140 K43-145 135 101 13 249 3.0 Hoesch isorock vario 160 K43-149 150 114 277 3.3 175 K43-146 155 109 277 3.3 180 K43-147 125 111 249 3.0 150 K43-148 175 99 287 3.4 200 Fastening angle Coating 0.75 max. 3000 Manufacturer s choice Girth Development Weight kg/m K73-011 31 62 0.4 K73-012 57 88 0.5 Suitable for lateral edging for windows and doors Cover flashing 0.75 max. 6000 Girth Development Weight Suitable for C Product Element thickness kg/m K43-111 138 205 1.2 100 K43-112 179 246 1.5 120-140 lateral edging K43-113 206 273 1.6 160 of apertures K43-114 217 284 1.7 175 K43-115 241 308 1.9 200 Cover flashing B 0.75 max. 6000 Development Weight Suitable for Product Element thickness kg/m K43-121 176 1.1 lateral edging of apertures 60 22
Integral brackets, long Material Coating Suitable for Steel manufacturer s choice End and intermediate supports Suitable for Product Element thickness Z43-011 60 Z43-017 80 Hoesch isowand integral Z43-018 100 Z43-098 120 Integral brackets, long Material Coating Suitable for Steel work s choice End and intermediate supports Suitable for Product Element thickness Z43-091 Hoesch isowand integral 140 Integral brackets, short Material Coating Suitable for Steel work s choice End and intermediate supports Girth Suitable for H Product Element thickness Z43-012 ca. 26 Z43-016 ca. 46 80 Hoesch isowand integral Z43-019 ca. 66 100 Z43-099 ca. 86 120 60 Load distribution plate 1 Material 2.00 Stainless steel Z43-141 Suitable for use Concealed fastening of Hoesch isowelle, Hoesch isowand vario and Hoesch isorock vario, Hoesch isowand design Load distribution plate 2 Material 3.00 Stainless steel Z43-142 Suitable for use Concealed fastening of Hoesch isowelle, Hoesch isowand vario und Hoesch isorock vario 23
Wall connections Top hats luminium top hat 25, straight (part 1) Material luminium Coating luminium, natural / powder-coated / spray-painted 6000 Suitable for Z43-021 Hoesch isowand integral, Hoesch isowand vario luminium insert (part 2) Material Coating luminium luminium, natural / powder-coated / spray-painted 6000 Z73-011 Suitable for Hoesch isowand integral, Hoesch isowand vario, straight aluminium top hat 25 / 10 luminium top hat 25, curved (part 1a) Material Coating luminium luminium, natural / powder-coated / spray-painted Suitable for Z43-022 Hoesch isowand integral, Hoesch isowand vario, curved outer corner, curved parapet luminium insert (part 2a) Surface luminium, natural / powder-coated / spray-painted Z73-012 Suitable for Hoesch isowand integral, Hoesch isowand vario, bent aluminium joint cover strip 25 / 10 The insert engages at a distance of 100 along the joint cover strip in order to ensure the alignment of the profiles. The radius relates to the outer edge of Hoesch isowand. Gasket (part 3) Colour Delivery form Suitable for m/rolle Z73-021 black 50 Hoesch isowand integral, Hoesch isowand vario aluminium joint cover strip 25 PE foam strip (closed-cell) (part 4) 2000 Material Polyethylene Colour Suitable for use Z43-071 white Hoesch isowand integral, Hoesch isowand vario joint filler when using aluminium joint cover strips 24
200 100 luminium top hat, straight design (part 1) Material luminium Coating luminium, natural / powder-coated / spray-painted 6000 Suitable for Z43-051 Hoesch isowand integral, Hoesch isowand vario e.g. compensation joint luminium insert (part 2) Material Coating Z73-011 luminium luminium, natural / powder-coated / spray-painted 6000 Suitable for Hoesch isowand integral, Hoesch isowand vario, straight aluminium top hat 25 / 10 luminium top hat 10, bent design (part 1a) Material luminium Coating luminium, natural / powder-coated / spray-painted 100 200 Z43-052 luminium insert (part 2a) Material Coating Suitable for Hoesch isowand integral, Hoesch isowand vario, curved outer corner, curved parapet luminium luminium, natural / powder-coated / spray-painted Part 1a Part 2a Part 3 R 380 R 380 Z73-012 Suitable for Hoesch isowand integral, Hoesch isowand vario, gebogene l-fugenleiste 25 / 10 The insert engages at a distance of 100 along the joint cover strip in order to ensure the alignment of the profiles. The radius relates to the outer edge of Hoesch isowand. Sealing tape (part 3) Colour Girth Delivery (w x h) form m/rolle Suitable for Z70-B01 black 20 x 3 30 see page 42 PE foam strip (closed-cell) (part 4) Material 2000 Polyethylene Colour Suitable for Product Z43-071 white Hoesch isowand integral, Hoesch isowand vario joint filler when using aluminium joint cover strips 25
200 100 luminium top hat Hoesch isowelle, straight (part 1) Surface luminium, natural / powder-coated / spray-painted 6000 Suitable for Z43-061 Hoesch isowelle e.g. compensation joint luminium insert Hoesch isowelle (part 2) Surface luminium, natural / powder-coated / spray-painted 6000 Z73-071 Suitable for Hoesch isowelle straight aluminium top hat 100 200 luminium top hat Hoesch isowelle, curved (part 1a) Surface luminium, natural / powder-coated / spray-painted Part 1a R 380 Suitable for Part 2a Z43-062 Hoesch isowelle curved outer corner, curved parapet Part 3 luminium insert Hoesch isowelle (part 2a) R 380 Surface luminium, natural / powder-coated / spray-painted Suitable for Hoesch isowelle Z73-072 bent aluminium joint cover strip The insert engages at a distance of 100 along the joint cover strip in order to ensure the alignment of the profiles. The radius relates to the outer edge of Hoesch isowand. PE foam strip (closed-cell) (part 3) Overall length 2000 Colour Girth Suitable for Product Thickness (d) H/ Z43-131 50 84 white Hoesch isowelle Z43-132 70 104 Installation strip Material EPDM Hoesch isowand vario Hoesch isowelle installation strip Dimension Delivery form m/rolle Z70-F01 4 x 15 10 Suitable for Combination Hoesch isowelle with Hoesch isowand vario using jluminium top hat Z43-061 26
luminium top hat Hoesch isorock, straight design (part 1) Material Coating luminium luminium, natural / powder-coated / spray-painted 6000 Suitable for Z43-121 Hoesch isorock, Hoesch isorock vario luminium insert Hoesch isorock (part 2) Material Coating luminium luminium, natural / powder-coated / spray-painted 6000 Z73-011 Suitable for Hoesch isorock, Hoesch isorock vario straight aluminium joint cover strip Gasket (part 3) Material Coating luminium, natural / powder-coated / spray-painted Delivery form Suitable for m/roll Z73-021 50 Hoesch isorock, Hoesch isorock vario top hat Z43-121 Support profile Coating 2.00 max. 8000 side: DU 9002 B side: RSL, Manufacturer's choice Development Weight Suitable for use kg/m Z43-181 249 4.0 For connecting top hats to steel supports Water drainage sheet Coating 0.75 max. 6000 Manufacturer's choice Development Weight Suitable for use kg/m Z43-131 88 0.5 Horizontal joint with top hat Z43-021 27
Wall connections Hoesch isowand integral with FSI window system dapter profile top (part 1) Material luminium extrusion, mill finish Isolator Polyamid, black 6000 Suitable for Element thickness Z43-F21 Z43-F23 80 Z43-F25 integral window system 100 Z43-F27 120 Z43-F29 140 60 dapter profile bottom (part 2) Material Isolator luminium extrusion, mill finish Polyamid, black 6000 Suitable for Element thickness Z43-F22 Z43-F24 80 Z43-F26 integral window system 100 Z43-F28 120 Z43-F30 140 60 28
Gasket (parts 3 + 4) Material EPDM Delivery form Suitable for m/roll Z73-022 200 1) lower gasket integral window system Z73-023 100 1) upper gasket integral window system 1) smaller quantities on request Round cord (part 5) Material EPDM Diameter Delivery form Suitable for m/roll Z73-081 2.5 200 1) integral window system 1) smaller quantities on request Sealing tape (part 6) On PUR basis, open cell with synthetic resin impregnation, pre-compressed, one side self-adhesive Girth Delivery Recoended Suitable for (w/h) form m/roll joint width Product Element thickness () Z70-08 40/11-25 2.6 11-25 integral window system 80-140 Z70-11 20/9-20 3.3 9-20 lower sealing integral window system 60 Z70-12 20/5-12 5.6 5-12 upper sealing integral window system 60 Exclusively for Hoesch isowand integral with FSI window system T profile Material luminium 1.00 Ordering length Modular height + 100 Coating mill finish Suitable for Z43-501 integral window system 30 40 Ordering length = Bestelllänge Modular = height Modulhöhe + 100 + 100 29
Roof connections General Edge flashing Profile (always consists of two different profiles - 2 x E and 2 x F) Ordering length (L E / L F ) 0.75 according to specification (max. 4000 ) E, cross section with end laps F, longitudinal profile without end laps E, L E = Girth E + 224 F, L F = Girth F (without addition) Dimension E and dimension F = clear width of the roof aperture at the bottom flange -40 aperture (see sketch page 31); min. 200 Girth Development Weight Suitable for use Form E Form F H K K30-310 K30-410 160 128 K30-311 K30-411 170 118 K30-312 K30-412 180 108 K30-313 K30-413 190 98 K30-314 K30-414 200 88 K30-315 K30-415 210 78 K30-316 K30-416 220 68 K30-317 K30-417 230 58 K30-318 K30-418 240 130 K30-319 K30-419 250 120 K30-320 K30-420 260 110 K30-321 K30-421 270 100 K30-322 K30-422 280 90 K30-323 K30-423 290 80 K30-324 K30-424 300 70 K30-325 K30-425 310 60 K30-326 K30-426 320 173 K30-327 K30-427 330 163 K30-328 K30-428 340 153 K30-329 K30-429 350 143 K30-330 K30-430 360 133 K30-331 K30-431 370 123 kg/m 410 2.5 492 3.0 615 3.7 Roof apertures in Hoesch trapezoidal profiles and Hoesch Roof System 2000 For the last digits of part numbers K30-3.. and K30-4.., please refer to the table on the right and see example for ordering. Example for ordering Data Dimension Dimension Dimension Product E F a Hoesch Trapezoidal profile T-135.1 1000 1000 1200 100 Order 2 nos. K30-320, L E = 1.224 2 nos. K30-420, L F = 1.200 30
The last digits of part numbers K 30-3.. and K30-4.. Hoesch Trapezoidal profile Girth a = height of the roof superstructure above the profile 0 10 20 30 30 50 60 70 80 90 100 110 120 130 140 150 160 170 180 190 200 T35.1 (, D) T40.1 (, D, S) 10 10 12 13 14 15 16 17 18 19 20 T50.1 10 11 11 13 14 15 16 17 18 19 20 21 T85.1 10 11 12 13 14 15 15 17 18 19 20 21 22 23 24 25 T100.1 () 11 12 13 14 15 16 16 18 19 20 21 22 23 24 25 26 T106.1 10 10 12 13 14 15 16 17 17 19 20 21 22 23 24 25 26 27 T135.1 () 10 11 12 13 13 15 16 17 18 19 20 20 22 23 24 25 26 27 28 29 30 T150.1 T160.1 () 12 13 14 15 15 17 18 18 20 21 22 22 24 25 26 27 28 29 30 31 T205.1 10 11 12 13 14 15 16 17 18 Hoesch Dachsystem 2000 1 10 11 12 13 14 15 16 17 18 The part numbers K30-3.. and K390.. are supplemented by the applicable last digits as per this table, see example for ordering. 1 In the case of Hoesch Roof System 2000, the top flange is edged by its cross beads, see sketch on page 34. Form E Cross profile K30..3 with notch on both ends Form F Longitudinal profile K30..4 with drill holes Ø 5 on both ends perture Dimension: Frame: E x F perture in the edge flashing on top of the Hoesch trapezoidal profile to extend 40 beyond the top flange of the edge flashing. 31
Structural longitudinal trier / C profile ll dimensions denoted with a capital letter are external face dimensions H = External face dimension h = Internal face dimension Surface 3.00 coil-coated / piece-coated (on request) Girth Development Weight Suitable for B C H K31-061 kg/m 206 86 Hoesch Trapezoidal profile T-85.1 K31-063 186 106 Hoesch Trapezoidal profile T-100.1 K31-064 181 111 Hoesch Trapezoidal profile T-106.1 333 8.0 K31-065 35 152 24 140 Hoesch Trapezoidal profile T-135.1 K31-067 136 156 Hoesch Trapezoidal profile T-150.1 K31-068 131 161 Hoesch Trapezoidal profile T-160.1 K31-069 251 208 500 12.0 Hoesch Trapezoidal profile T-205.1 2.00 Surface GLVLUME Girth Development Weight Suitable for B C H K31-071 kg/m 183 85 311 5.0 Hoesch Trapezoidal profile T-85.1 K31-072 163 105 311 5.0 Hoesch Trapezoidal profile T-100.1 K31-073 158 110 311 5.0 Hoesch Trapezoidal profile T-106.1 K31-074 35 129 20 139 311 5.0 Hoesch Trapezoidal profile T-135.1 K31-075 158 155 356 5.7 Hoesch Trapezoidal profile T-150.1 K31-076 108 160 311 5.0 Hoesch Trapezoidal profile T-160.1 K31-077 183 207 415 6.6 Hoesch Trapezoidal profile T-205.1 Gully reinforcement 1.50 Surface coil-coated / piece-coated Unit Weight Suitable for kg K30-261 5.9 Hoesch trapezoidal profiles 32
External ridge and valley flashing 0.75 When ordering, please indicate the pitch angle of the roof α. Range: 3 < α < 30 Girth Development Weight Suitable for C kg/m K30-091 307 615 3.7 K30-092 77 155 0.9 K30-094 205 410 2.4 Hoesch Trapezoidal profile, Sandwich elements K30-103 250 530 3.2 External ridge flashing 0.75 When ordering, please indicate the pitch angle of the roof α. Range: 3 < α < 30 Grith Development Weight Suitable for C kg/m K30-101 192 410 2.5 Hoesch Trapezoidal profile, K30-102 295 615 3.7 Sandwich elements External ridge a flashing - gable roof 1.00 ngle Development Weight Suitable for β kg/m K33-080 180-2xα 554 4.4 Hoesch isorock integral D When ordering, please indicate the pitch angle of the roof α. Range: 3 < α < 30 Notched edge profile sheet, one-sided pplication 0.75 On the ridge of gable roofs together with ridge profile K30-10 Girth ngle Development Weight Suitable for C D β Grad kg/m K30-111 208 1031 120 1.5 Hoesch Trapezoidal profile T-35.1, B side K30-112 202 911 120 1.5 Hoesch Trapezoidal profile T-40.1, B side K30-113 191 996 120 246 1.5 Hoesch Trapezoidal profile T-50.1, B side K30-116 210 996 132 1.5 Hoesch Thermo roof, Hoesch isodach integral 33
When ordering, please indicate the pitch angle of the roof α. Range: 3 < α < 30 Eave closure flashing 1.00 Girth Development Weight Suitable for B Product Thickness of roof element kg/m K30-120 210 74 351 1.8 K30-121 50 59 176 1.4 75 K30-122 70 68 205 1.6 95 K30-123 90 89 246 2.0 Hoesch 115 Trapezoidal K30-124 110 69 246 2.0 130/135 profile, K30-125 130 76 273 2.2 155 Sandwich K30-126 150 67 284 2.3 elements 175 K30-127 60 78 205 1.6 85 K30-128 80 58 205 1.6 105 K30-129 160 81 308 2.5 185 235 Eave drip flashing When ordering, please indicate the pitch angle of the roof α. Range: 3 < α < 30 0.75 Development Weight Suitable for kg/m K30-131 246 1.5 Hoesch Trapezoidal profile, Sandwich elements Edge flashing 1.00 Girth Development Weight Suitable for B Product Element thickness* kg/m K33-021 40 37 137 1.1 K33-022 60 34 154 1.2 60 K33-023 80 36 176 1.4 80 K33-024 95 50 205 1.7 PUR and MW 95 K33-025 115 71 246 1.9 sandwich 115 K33-026 135 51 246 1.9 elements 135 K33-027 155 58 273 2.1 155 K33-028 175 73 308 2.4 175 K33-029 200 48 308 2.4 200 * core thickness 40 34
Roof connections Covered attachment Cover cap Ridge Material (L) (L B ) Steel 0.63 6000 (mind. 1400, max. 6500 ) L + 100 Weight Suitable for kg/m Cover strip of ordering Eaves L = Overall length Hoesch isodach integral Hoesch isodach mono S33-051 0.7 Hoesch isodach integral, Hoesch isodach mono S33-052 0.7 Hoesch isorock integral D (including 2 sealing tapes) Cover strip of ordering Ridge L = Overall length Eaves Sealing tape, factory-applied Hoesch isorock integral D Load distribution channel Material luminium 100 Suitable for Z33-051 100 Hoesch isodach integral, Hoesch isodach mono Z33-052 200 and Hoesch isorock integral D Hoesch isodach integral Hoesch isodach mono Hoesch isorock integral D Z profile Material Steel Thickness 1.00 Coating GLVLUME Z profile Development Weight Suitable for kg/m K33-031 6000 (max. 8000) Hoesch isodach mono Ortgang 95 0.8 K33-032 900 Hoesch isodach mono First 35
Top hat Top hat to support the eave closure flashing View 1.00 50 Coating GLVLUME View Hat profile Height Development Weight Suitable for kg/m K73-041 34 176 1.4 Hoesch isodach mono K73-042 18 137 1.1 Hoesch isorock integral D Cover flashing d 0.75 1020 Coating GLVLUME Overall width 1000 Development Weight Suitable for Product Element thickness kg/m K33-064 250 1.48 150 Hoesch isorock integral D K33-065 300 1.77 200 36
Roof connections Hoesch rched Roof Verge flashing, curved 0.75 6000 Girth max. Radius cut (R) kg/m Suitable for S35-021 100 340 2500 Hoesch rched Roof with S35-022 200 440 3000 R 4000 or other S35-023 300 540 3000 polygonal elements When ordering, please indicate the dimensions B, L and R. The curved shape is achieved by bending the vertical leg. Please note: Minimum radius of Hoesch rched Roof 4000 Top hat 6000 Suitable for S35-011 1.00 S35-012 1.50 Hoesch rched Roof, double sheet design S35-013 2.00 Clamping plate pplication For fastening the arc lower sheet to the substructure Hoesch rched Roof Profile Hole diameter Design Suitable for D kg/m S35-033 galvanized HP 41B / 160 14 S35-034 galvanized and painted S35-035 galvanized HP 107B / 250 17 S35-036 galvanized and painted Hoesch rched Roof 37
Roof connections Hoesch Roof System 2000 Supporting element Surface pplication both sides DU light (other colours on request, subject to quantities ordered) Load transfer into the substructure Material thickness Width vailability Weight Suitable for b kg/stück K32-011 1.0 150 Standard 1.3 K32-013 1.0 250 only on request 2.1 K32-014 1.5 150 Standard 1.9 K32-016 1.5 250 only on request 3.2 Installation only in combination with installation tape K32-02 Hoesch Roof System 2000 Installation tape Surface 1.00 ca. 3750 both sides coil-coated (light colour) Width Unit Suitable for use b Weight kg K32-021 150 4.5 Hoesch Roof System 2000, K32-023 250 7.5 for fastening 5 support cleats and for load End cap Surface 0.75 coil-coated or side DU light Unit Weight Suitable for use kg K32-031 0,2 Hoesch Roof System 2000, for sealing ribs in the event of roof apertures Example of application End cap and edging profiles For edging profiles K30-3 and K30-4, please see page 26. K30-3.. 1000 K32-031 K30-4.. 38
Flashings for floors and ceilings Hoesch dditive Floor Cover flashing 1.00 580 Coating side: 25 µm (standard: PLDUR SP RL 9002) B side: Manufacturer s choice Unit Weight Suitable for kg Z52-021 580 / 520 0,3 Hoesch dditive Floor for a cleat height of 35 Z52-021 Delivery only in combination with Hoesch dditive Floor. End cap Material pplication Plastic for sealing the ribs of the floor profiles of Hoesch dditive Floor Suitable for Z52-011 Hoesch dditive Floor Delivery only in combination with Hoesch dditive Floor. End cap for diagonal cuts Delivery length ca. 1000 Material pplication PUR foam for sealing the ribs of the floor profiles of Hoesch dditive Floor Suitable for use Z52-032 Z52-031 Z52-031 Hoesch dditive Floor girder connection Z52-032 Hoesch dditive Floor wall connection Delivery only in combination with Hoesch dditive Floor. 39
Flashings for floors and ceilings Suspended ceilings for cold store panels luminium hanger bar T profile consisting of Suitable for part Designation Z53-011 1 luminium T-profile, anodized, perforated (6000 ) Z53-021 2a Threaded rod M10 - right-hand thread Z53-022 2b Threaded rod M10 - left-hand thread Z53-031 3a Threaded socket M10 - right-hand thread Z53-032 3b Threaded socket M10 - left-hand thread Z53-041 4a Clevis - right-hand thread Z53-042 4b Clevis - left-hand thread Z53-051 5 Spring cup pin cold store panels Complete right-hand thread consisting of Quantity Suitable for part Designation 1 luminium T profile, anodized, perforated (6000 ) 1 2a Threaded rod M10 - left-hand thread 5 cold store Z53-071 4a Clevis - left-hand thread 5 panels 5 Spring cup pin 5 Complete left-hand thread consisting of Quantity Suitable for part Designation 1 luminium T profile, anodized, perforated (6000 ) 1 2b Threaded rod M10 - left-hand thread 5 cold store Z53-072 4b Clevis - left-hand thread 5 panels 5 Spring cup pin 5 Clevis with right-hand thread and clevis pin retention clip consisting of Quantity Suitable for part Designation 4a Clevis - right-hand thread 1 Z53-081 cold store panels 5 Spring cup pin 1 Clevis with left-hand thread and clevis pin retention clip consisting of Quantity Suitable for part Designation 4b Clevis - right-hand thread 1 Z53-082 cold store panels 5 Spring cup pin 1 luminium angle Material 4.0 6000 luminium, anodized Suitable for Z53-061 cold store panels 40
ccessories Profile filler Profile filler Material Colour Delivery form Ordering Cellular polyethylene (exception Z73-05 polyethylene foam) Rear: white Front: black Profile strip, running metre (exception: Z73-04: in individual pieces) Only running metres (exception: Z73-04: in individual pieces) Hoesch Trapezoidal profile / Hoesch Roof System 2000 / Hoesch rched Roof Profile filler for side for side Thickness Suitable for Z71-03 Hoesch Trapezoidal profile T-35.1 Z71-B03 B Hoesch Trapezoidal profile T-35.1 D Z71-04 Hoesch Trapezoidal profile T-40.1 Z71-B04 B Hoesch Trapezoidal profile T-40.1 D Z71-05 Z71-B05 B Hoesch Trapezoidal profile T-50.1 Z71-06 Z71-B06 B Hoesch Trapezoidal profile T-85.1 Z71-08 Hoesch Trapezoidal profile T-100.1 Z71-B08 B 25-30 Z71-09 Hoesch Trapezoidal profile T-106.1 Z71-B09 B Z71-10 Z71-B10 B Hoesch Trapezoidal profile T-135.1 Z71-12 Z71-B12 B Hoesch Trapezoidal profile T-150.1 Z71-13 Z71-B13 B Hoesch Trapezoidal profile T-160.1 Z71-14 Z71-B14 B Hoesch Trapezoidal profile T-205.1 Z72-01 Z72-B01 B ca. 55 Hoesch Roof System 2000 S35-044 ca. 30 Hoesch rched Roof HP41 S35-045 ca. 50 / B S35-046 ca. 30 S35-047 ca. 50 Hoesch rched Roof HP107 Profile filler for side B Profile filler for side B Profile filler for side Hoesch Trapezoidal profile Hoesch rched Roof Sandwich elements Roof Thickness Suitable for Z73-01 25-30 Hoesch Thermodach, Hoesch isodach integral Z73-04 1 30 Hoesch isodach mono 1 Delivery form: individual pieces; 1 piece/m required Profile filler for Hoesch Thermodach Hoesch Thermodach Profile filler for Hoesch isodach mono Hoesch isowelle Profile filler for Hoesch isowelle Height Thickness Suitable for use Z73-02 6 Connecting piece is in contact with Hoesch isowelle 27 Z73-03 16 Connecting piece is connected through spacer Z43-1011 (page 12) Hoesch isowelle Hoesch isorock integral D Material Polyethylene foam Thickness Suitable for Z73-05 27 Hoesch isorock integral D Profile filler for Hoesch isorock integral D 41
ccessories Sealing materials Sealing tapes PUR based, open cells, saturated with synthetic resin, pre-compressed, one side self-adhesive Girth Delivery Recoended Suitable for (B/D) Form m/rolle joint width Z70-02 20 / 1-4 13 1-4 Sealing during Z70-03 30 / 1-4 13 1-4 installation Z70-05 30 / 4-9 8 4-9 PUR based, open cells, saturated with synthetic resin, pre-compressed, one side self-adhesive Girth Delivery Recoended Suitable for (B/D) Form joint width Product Element thickness m/roll () Z70-08 40 / 11-25 2,6 11-25 Window system integral 80-120 Z70-11 20 / 9-20 3,3 9-20 Window system integral, bottom 60 Z70-12 20 / 5-12 5,6 5-12 Window system integral, top 60 Exclusively to be used for Hoesch isowand integral with FSI window system. PVC based, closed-cell, one side self-adhesive Girth (D x B) Delivery Form m/roll Z70-B01 3 x 20 30 Z70-B02 5 x 20 20 Z70-B03 10 x 20 10 Z70-B04 10 x 50 10 Suitable for Sealing of longitudinal and lateral joints of components Polyvinyl chloride, closed-cell, one side self-adhesive Girth Delivery Suitable for (D x B) Form m/roll Z70-C01 4 x 50 15 Hoesch Thermodach, Hoesch isodach cross joints Polyurethane flexible foam, one side self-adhesive Girth Delivery Suitable for (D x B) Form m/roll Z70-D01 14 x 3-9 14 Hoesch Thermodach, Hoesch isodach cross joints Plastic sealant, profile-shaped, based on butyl rubber, highly adhesive, self-sealing Girth Delivery Form Suitable for m/roll Z70-E01 6 78 Hoesch Thermodach, Hoesch isodach cross joints Butyl tape, permanently adhesive, self-sealing, permanently elastic Girth (D x B) Delivery Form Suitable for m/roll Z70-E02 4 x 20 10 Hoesch isodach mono Hollow chamber gaskets, EPDM terpolymer rubber, one side self-adhesive Girth (D x B) Delivery Form Suitable for m/roll Z70-F01 4 x 15 10 cross joint between horizontally laid Hoesch isowelle und Hoesch isowand vario, S. 22 Z73-F02 10 x 12 75 Hohlprofil Hoesch isowelle Roof 42
ccessories Sealing materials and installation aids Sealant Hollow profile, EPDM, one-sided self-adhesive Cartridge content Description Suitable for cm 3 Z70-051 Z70-052 310 elastic, transparent, aminohardening sealant silicone based, plastic, grey, butyl based ußen- und outside and inside use, e.g. joints of flashings, connections inside use, e.g. for sealing longitudinal joints of Hoesch liner trays Clamping device Description Please note Installation device with a reversible ratchet Please indicate element thickness when ordering! Hoesch isowand integral Product Suitable for Element thickness Z43-111 Installation of 60-120 Z43-091 Hoesch isowand integral 140 Hoesch isowelle and Hoesch isowand vario Suitable for Product Element thickness Z43-113 Installation of Hoesch isowelle and Hoesch isowand vario 60-104 Z43-116 Installation of Hoesch isowand vario 120-140 Hoesch isorock, Hoesch isorock vario and Hoesch Matrix Suitable for Product Element thickness Z43-114 Installation of Hoesch isorock, 60-120 Z43-115 Hoesch isorock vario and Hoesch Matrix 120-200 Hoesch isorock integral D Hoesch isotrim Product Suitable for Element thickness Z33-112 Installation of Hoesch isorock integral D 95-155 Scope of delivery Suitable for Z00-011 Cutting device including Makita JR 3030 type saw neat and straight cutting of sandwich elements (max.d=150) Spindle clamp 1) Description Suitable for Product Clamping dimension Z43-0211 40-140 2) Z43-0212 with slip 100-240 Sandwich elements Z43-0213 resistant coating 200-300 2) Z43-171 60-180 3) 1) can also be hired 2) on request 3) discontinued model 43
Special flashings General Special flashings Material Surface coating Development Dimensions as standard flashings 0.75 / 1.00 / 1.50 / 2.00 / 3.00 600 (Standard, max. 8000 ) can be selected for side and side B, as in the case of standard flashings freely determinable (to avoid scrap, the development should be a clean fraction of the width of the stock material) Example: development 410 = 1,230 / 3 from stock material 0.75 x 1,230, see page 41 The dimensions indicated on the sketch should always be inside dimensions! s must be indicated in millimetres, angles in degrees and rounded off to whole numbers. Folds Limit values Back folding 12, Precondition: material thickness 1,00 Enclosed angle 45 U shape B Z shape D 12, wenn t = 0.75-1.50 D 20, wenn t = 2.00-3.00 E 65, wenn D 120, sonst kann E größer sein First and last fold < 3, then 12 = 3, then 22 44
Round Gutter System 45
Flashing components for round gutter system Z33-100_ Eaves gutter O ion length up to 4,000 O 075 O Diameter D O and number of pieces O Color and coating type D D [] Girth [] Z33-1001 120 596 Z33-1002 160 599 Z33-1003 200 602 Z33-1004 240 605 Z33-101_, Z33-125_ End item O Diameter D O 0.75 O ssembly right, left O Number of pieces O Color and coating type D D [] Position Z33-1011 120 right Z33-1012 160 right Z33-1013 200 right Z33-1014 240 right Z33-1251 120 left Z33-1252 160 left Z33-1253 200 left Z33-1254 240 left Z33-102_ Gully O Diameter d O 0.75 O and number of pieces O Color and coating type d [] Z33-1021 80 Z33-1022 100 Z33-1023 120 Z33-1024 150 L [] L d 46
Flashing components for round gutter system Z33-103_ Conical gully O Diameter d, D O 0.75 O Number of pieces O Color and coating type d [] D [] D Z33-1031 80 Z33-1032 100 Z33-1033 120 Z33-1034 150 d Z33-104_ S-offset (top) O Diameter d O 0.75 O Dimension C O Number of pieces O Color and coating type d [] C [] C 30 150 Z33-1041 80 Z33-1042 100 Z33-1043 120 Z33-1044 150 150 d Z33-105_ Expansion basket O Diameter d, D O 0.75 O Number of pieces O Color and coating type d [] D Z33-1051 80 Z33-1052 100 Z33-1053 120 Z33-1054 150 D [] d 47
Flashing components for round gutter system Z33-106_ Downpipe O ion length up to4 000 O Materialdicke 0,75 O Diameter d O L O Number of pieces O Color and coating type d [] Z33-1061 80 Z33-1062 100 Z33-1063 120 Z33-1064 150 L [] L d Z33-107_ Downpipe bracket O Diameter d O Number of pieces O Color and coating type d [] Z33-1071 80 Z33-1072 100 Z33-1073 120 Z33-1074 150 Z33-108_ S-offset (bottom) O Diameter d O 0.75 O Dimension C, ngle β O Number of pieces O Color and coating type d [] C [] β [ ] 150 C Z33-1081 80 Z33-1082 100 Z33-1083 120 Z33-1084 150 β d 150 48
Flashing components for round gutter system Z33-109 Outlet bend O Diameter d O 0.75 O Number of pieces O Color and coating type d [] B [] 250 d 135 Z33-110 Eaves gutter bracket O Diameter D O Number of pieces O Color and coating type 2 Loch 7 D 220 D [] Z33-1101 80 Z33-1102 100 Z33-1103 120 Z33-1104 150 Flat sheet 5x30 Z33-900 Eaves gutter bracket O Diameter D O Dimension B O Slope α O Number of pieces O Color and coating type D [] B [] α [ ] D 2 Loch 7 α Z33-9001 80 Z33-9002 100 Z33-9003 120 Z33-90044 150 B Z33-1091 80 Z33-1092 100 Z33-1093 120 Z33-1094 150 B Flat sheet 5x30 49
Flashing components for round gutter system Z33-901 Eaves gutter bracket O Diameter D O Hook offset O Hook height B O Number of pieces O Color and coating type D [] [] B [] 4 7 hole B Flat sheet 5x30 Z33-9011 80 Z33-9012 100 Z33-9013 120 Z33-9014 150 D Flat sheet 5x30 50
ngular Gutter System Foam-free zone Profile filler 51
Flashing components for angular gutter system Z33-111_ ngular gutter O Production length up to 6,000 O 0.75 O Panel type O Roof slopeα O and number of pieces O Color and coating type 90 (89) 85 (84) 35 15 160 100 + α 100 175 (173) 18 90 + α 35 α X α [ ] X [] Girth [] X [] Girth [] Z33-1111 2 140 590 140 590 Z33-1112 4 146 596 146 596 Z33-1113 6 152 602 152 602 Z33-1114 9 161 611 161 611 Z33-1115 12 171 621 171 621 Z33-1116 15 180 630 180 630 Z33-1117 18 189 639 189 639 Z33-1118 21 198 648 198 648 Z33-112_ Gutter junction O The standard item doesn t include any holes for the rivet O 0.75 O Dimension X O Number of pieces O Color and coating type 89 84 160 100 X α [ ] X [] Girth [] X [] Girth [] Z33-1121 2 140 590 140 590 Z33-1122 4 146 596 146 596 Z33-1123 6 152 602 152 602 Z33-1124 9 161 611 161 611 Z33-1125 12 171 621 171 621 Z33-1126 15 180 630 180 630 Z33-1127 18 189 639 189 639 Z33-1128 21 198 648 198 648 173 Z33-113_ Cage O Diameter d O Number of pieces O Color and coating type d [] Z33-1131 100 Z33-1132 120 Z33-1133 150 d 52
250 250 Flashing components for angular gutter system Z33-114_ Square inlet O Diameter d O 0.75 O L O Number of pieces O Color and coating type d [] d Z33-1141 100 Z33-1142 120 Z33-1143 150 L [] d Z33-115_ Downpipe square O 0.75 O Dimension L O Dimension B O Number of pieces O Color and coating type B B [] Z33-1151 100 100 Z33-1152 120 120 Z33-1153 150 150 L [] (standard) L L B Z33-902_ Offset square top elbow O The standard length of the elbow is 250 250 (in this case the C dimension is variable from 180 to 310 ) O 0.75 O Dimension B, C O ngle β O Number of pieces O Color and coating type C 250 B B [] β [ ] (standard) C [] β 250 Z33-9021 100 100 45 Z33-9022 120 120 45 Z33-9023 150 150 45 B 53
Flashing components for angular gutter system Z33-117_ Sleeve square O Dimension, B, C O Number of pieces O Color and coating systems B B [] [] (standard) C [] (standard) B Z33-1171 100 100 30 50 Z33-1172 120 120 40 50 Z33-1173 150 150 40 50 B C Z33-116_ Outlet bend square O 0.75 O Dimension B O Number of pieces O Color and coating systems B+2 B B [] Z33-1161 100 100 Z33-1162 120 120 Z33-1163 150 150 135 250 250 Z33-118_ Stop end O 0.75 O ssembly right, left O Roof slope α O Color and coating type Position Roof pitch α [ ] Z33-1181 right Z33-1182 left 54
Flashing components for angular gutter system Z33-120_ Bracket O Production length 600 O Panel type O Number of pieces O Color and coating type Panel type [] B [] α [ ] Girth [] Z33-1201 40 35 57 132 β B 15 15 B β Z33-905_ Prefabricated angle gutter / gable O 0.75 O ssembly right, left O Roof slope O Number of pieces O Color and coating type 90 Roof pitch Position Roof pitch [ ] Z33-9051 right Z33-9052 left Z33-905_ Z33-111_ 500 500 55
Flashing components for angular gutter system Z33-903_ Elbow gutter positive, negative O 0.75 O Roof slope α O Number of pieces O Color and coating type Positive elbow gutter Roof slope α [ ] 90 Z33-9031 300 300 Negative elbow gutter Z33-9032 90 300 300 Z33-904_ Transformer item from square to round O The minimum L dimension is 200. O 0.75 O Dimension B, L O Diameter d O Number of pieces O Color and coating type B B [] square d [] round L [] minimum d Z33-9041 B+2 L d 56
Flashing components for angular gutter system Z33-119_ Square inlet O 0.75 O Dimension B, L O Number of pieces O Color and coating type B B [] L [] B-2 Z33-1191 100 100 Z33-1192 120 120 Z33-1193 150 150 L B-2 57
Insulated Rainwater System Z33-906_, Z33-907_ Insulated gutter O ion length up to 6,000 including end overlap O maximum limit of bottom girth is 1.250 O F = D 1.3 + 80 O insulation depth D O Roof slope α O total length of gutter, indicating the overlap size O for stop end specify RIGHT or LEFT option O Number of pieces O Color and coating type D [] Z33-9061 40 Z33-9062 50 Z33-9063 60 Z33-9064 80 Z33-9065 100 Z33-9066 120 Z33-9071 80 Z33-9072 100 Z33-9073 120 Roof slope α [ ] Total length [] stop end option PUR/PIR = 530 F a E = 200 b = 125 D B = 164 C = 300 Mineral wool = 530 F a E = 200 b = 125 D B = 164 C = 300 58
Insulated Rainwater System Z33-908_, Z33-909_ Insulated gutter O ion length up to 6,000 including end overlap O maximum limit of bottom girth is 1.250 O F = D 1.3 + 80 O insulation depth D O Roof slope α O total length of gutter, indicating the overlap size O for stop end specify RIGHT or LEFT option O Number of pieces O Color D [] Z33-9081 40 Z33-9082 50 Z33-9083 60 Z33-9084 80 Z33-9085 100 Z33-9086 120 Z33-9091 80 Z33-9092 100 Z33-9093 120 Roof slope α [ ] Total length [] stop end option PUR/PIR 25 D = 415 F a B = 164 b = 125 E = 200 C = 300 Mineral wool D = 415 F a B = 164 25 b = 125 E =200 C = 300 59
Insulated Rainwater System Z33-910_, Z33-911_ Insulated gutter O ion length up to 6,000 including end overlap O maximum limit of bottom girth is 1.250 O F = D 1.3 + 80 O insulation depth D O Roof slope α O total length of gutter, indicating the overlap size O for stop end specify RIGHT or LEFT option O Number of pieces O Color and coating type D [] Z33-9101 40 Z33-9102 50 Z33-9103 60 Z33-9104 80 Z33-9105 100 Z33-9106 120 Z33-9111 80 Z33-9112 100 Z33-9113 120 Roof slope α [ ] Total length [] stop end option PUR/PIR = 415 F a b = 125 E = 200 D B = 164 C = 300 Mineral wool = 415 F a D B = 164 b = 125 E =200 C = 300 60
B B Insulated Rainwater System Z33-912_, Z33-913_ Insulated gutter O ion length up to 6,000 including end overlap O maximum limit of bottom girth is 1.250 O F = D 1.3 + 80 O insulation depth D O Roof slope α O total length of gutter, indicating the overlap size O for stop end specify RIGHT or LEFT option O Number of pieces O Color and coating type D [] Z33-9121 40 Z33-9122 50 Z33-9123 60 Z33-9124 80 Z33-9125 100 Z33-9126 120 Z33-9131 80 Z33-9132 100 Z33-9133 120 Roof slope α [ ] Total length [] stop end option PUR/PIR G = 70 D F a 90 90 +a b = 125 E = 200 C = 300 Mineral wool G = 70 D F a 90 90 +a b = 125 E =200 C = 300 61
Locksmith components K43-125_ and K-43-126_ U profile Wall panel thickness D and number of pieces d [] D [] Sheet thickness [] L [] D ~10 D-18 25 K43-1250 40 K43-1251 50 K43-1252 60 K43-1253 70 K43-1254 80 K43-1255 100 K43-1256 120 K43-1257 150 K43-1258 170 K43-1259 200 K43-1260 40 K43-1261 50 K43-1262 60 K43-1263 70 K43-1264 80 K43-1265 100 K43-1266 120 K43-1267 150 K43-1268 170 K43-1269 200 1,5 1,0 K43-127_ Base profile galvanized sheet To be specified 3.0 Element thickness D L Number of pieces d [] D [] Sheet thickness [] L [] Dicke 3,0 70 D D K43-1270 40 K43-1271 50 K43-1272 60 K43-1273 70 K43-1274 80 K43-1275 100 K43-1276 120 K43-1277 150 K43-1278 170 K43-1279 200 3 62
Locksmith components K43-128_ and K43-129_ Syetrical angle To be specified Element thickness D and number of pieces d [] D [] Sheet thickness [] L [] D 70 K43-1281 40 K43-1282 50 K43-1283 60 K43-1284 70 K43-1285 80 K43-1286 100 K43-1287 120 K43-1288 150 K43-1289 170 K43-1289 200 K43-1290 40 K43-1291 50 K43-1292 60 K43-1293 70 K43-1294 80 K43-1295 100 K43-1296 120 K43-1297 150 K43-1298 170 K43-1299 200 1,5 1 K43-130_ syetrical angle To be specified and number of pieces Sheet thickness [] K43-1301 1.5 für L 3 000 K43-1302 1.0 für 3 000 > L 6 000 L [] 50 50 63
Locksmith components Z33-9141 Snow fence Snow fence should be installed according to manufacturers instructions. Exact location and quantity of snow fences must be specified by designer according to the technical documents. Number of pieces Z33-9141 panel type - 333 (250) Z33-9151 Snow fence type Snowking for RW panel Snow fence should be installed according to manufacturers instructions. Exact location and quantity of snow fences must be specified by designer according to the technical documents. RL Farbtöne Number of pieces designed for panel type Z33-9151 RW - (1 996) (42) (3) (50) 6 7 (100) (125) (208) (74) (21) (333,3) (164) (42) (3) 64
Passage Piping Packing Z33-121_ Dektite excellent sealing of round pipe penetrations on steel roof and wall panels rubber elastic collar compensates thermal and dynamic movements of pipes Number of pieces Pipe diameter [] Base dimension [] Roof slope [ ] EJOPLST [ml] EJOT Colordril [pcs] Z33-1211 0 35 99 99 0 60 8 Z33-1212 5 55 137 137 8 Z33-1213 50 70 178 178 12 80 Z33-1214 5 120 218 218 16 Z33-1215 110 170 284 284 0 35 20 Z33-1216 160 220 365 365 28 Z33-1217 160 300 453 453 310 32 Z33-1218 290 440 581 581 310 40 Z33-122_ Dektite Soaker biggr base allows proper location of sealing on the wall or roof easy and fast installation easier water flow around pipe penetration Number of pieces Pipe diameter [] Base dimension [] Roof slope [ ] EJOPLST [ml] EJOT Colordril [pcs] Z33-1221 75 155 410 360 80 30 Z33-1222 114 254 485 560 80 36 0 60 Z33-1223 254 406 708 635 310 52 Z33-1224 380 610 1 415 905 310 96 65
Passage Piping Packing Z33-123_ Dektite Retrofit for use in difficult roof conditions installation on existing pipes without uninstalling the tube Number of pieces Pipe diameter [] Base dimension [] Z33-1231 20 70 160 Roof slope [ ] EJOPLST [ml] EJOT Colordril [pcs] Z33-1232 50 185 273 80 19 0 40 Z33-1233 85 255 369 25 Z33-1234 235 425 780 680 310 57 12 Z33-124_ Dekstrip Flashing sealing of circular and rectangular sections material of sealing allows 20% elongation at edges the sealing is possible to be painted with acrylic paint application up to 40 of weather sheet section height Number of pieces Dimension [m] Silicone W 15 [ml] EJOT Colordril [pcs] Z33-1241 3.1 m 245 2 310 134 Z33-1242 10.0 m 245 5 310 410 66