QUICKDR@W FTTH ACCESS SOLUTION
QUICKDR@W The fastest, easiest solution for customer network connection Creating a network that can manage future demands and take rollout problems in its stride can be a challenge. The Prysmian QUICKDR@W by JCS Technologies has been specially designed for this, enabling low cost incremental installation of the final customer drop. QUICKDR@W is a fast and effective preconnectorised system for FTTH connections in mid- and low-density areas. QUICKDR@W is a complete system for the last mile, FTTH and campus networks encompassing the pre-connectorised fibre cable lead-in assembly, connectorised lead-in joint, and installation equipment With ruggedised cable leads, provided with connectors at each section end, the final connection to the customer is achieved by plugging directly into fibre management products within the external network and at the customer premises. The plug and play approach means that the final connection to the customer is achieved without the need for highly skilled operators or expensive equipment. FEATURES Direct fibre broadband connection Pre-connectorised bidirectional WDM link Easily installed through long ducts 2 QUICKDR@W FTTH ACCESS SOLUTION JCS TECHNOLOGIES JCSTECH.COM.AU
QUICKDR@W LEAD-IN ASSEMBLY (LIA) MK3 The QUICKDR@W Lead-in Assembly (LIA) MK3 is a pre-connectorised cable that provides the means of rapidly connecting a customer to the network. The assembly is for use with the QUICKDR@W Customer Lead in Joint (CLJ) MK3. The assembly comprises a QUICKDR@W Pulling Shroud, QUICKDR@W Lead-in Seal and QUICKDR@W cable for rapid installation of the customer connection. The QUICKDR@W Pulling Shroud is used to feed a cable through a length of duct. The shroud protects the fibre and connector during installation and provides easy assembly and quick access to the connector after the pulling operation. During this operation a swivel should be used between the LIA and the pulling rope. The QUICKDR@W Lead-in Seal is used to connect the LIA to the Connectorised Lead-in Joint (CLJ). A transport sleeve is used to protect the connector before installation into the CLJ. Suitable for single-fibre applications, the QUICKDR@W Lead-in Assembly MK3 comes with one SC/APC type connector at each end. FEATURES Ultra low friction nylon sheath design Smooth, quick duct installation, even if already occupied Long hauling lengths to 300m Termite resistant Low cost connection by one semiskilled installer ABS connector shroud prevents water and dust ingress to IP67 Shroud cord attachment pulling eye Bend limiting rubber strain relief boot protects fibre during installation Easily dismantled unit allows quick post installation access High performance SC/APC terminations QUICKDR@W FTTH ACCESS SOLUTION JCS TECHNOLOGIES JCSTECH.COM.AU 3
QUICKDR@W LIA SPECIFICATIONS Cable Material Maximium Installation Tension Maximum Cable Diameter Dynamic Bend Diameter Static Bend Diameter Fibre Number / Type Connector Type Operating Temperature Range Shroud Casing Connector Boot Lead-in Seal Transport Sleeve Sealing Optical Dry Heat 500 N 5 mm 180 mm 120 mm 1 / Singlemode SC/APC -20 to +70 C (5 to 95% RH} ABS Rubber Glass Filled Polypropylene Glass Filled Polypropylene IP67 1310, 1550 and 1625nm BS EN 60068-2-2Test Bb Testing Damp Heat IEC 60068-2-3: 1969 Change of Temperature IEC 60068-2-14: 1984 Vibration IEC 60068-2-6: 1995 Shock IEC 60068-2-27: 1987 QUICKDR@W LIA LOGISTICS Packed Dimensions (mm) 400L x 400W x 100D Length (m) Weight (kg) Length (m) Weight (kg) 25 1.40 175 5.90 35 1.70 200 6.65 Packed Weight 50 2.15 225 7.40 75 2.90 250 8.15 100 3.65 275 8.90 125 4.40 300 9.65 150 5.15 QUICKDR@W LIA ORDERING FCQ LIA-XXX-001-XXX CONNECTOR TYPE SCA SC/APC LCA LC/APC CABLE LENGTH 025 25m 035 35m 050 50m 075 75m 100 100m 125 125m 150 150m 175 175m 200 200m 225 225m 250 250m 275 275m 300 300m SHIPPING The QUICKDR@W Lead-In Assembly MK3 is supplied on a cardboard reel inside a cardboard box. 4 QUICKDR@W FTTH ACCESS SOLUTION JCS TECHNOLOGIES JCSTECH.COM.AU
QUICKDR@W CONNECTORIZED LEAD-IN JOINT (CLJ) MK3 The QUICKDR@W CLJ MK 3 is a purpose built customer access termination that allows the rapid and incremental activation of customer services utilising simple practices. The CLJ allows the plug in connection of up to 8 individual customer lead-in cables at the time of service activation. The CLJ is designed to be cascaded on a single distribution cable for optimised network design and can be used in all types of PON and PTP network configurations. The customer lead-in cables are supplied for a single fibre connection with SC/APC connector fitted at both ends of the lead-in cable assembly. FEATURES Up to 8 pre-connectorised QUICKDR@W LIAs can be installed into the lead-in seal ports Incremental customer connection enables deferred installation cost Following distribution phase CLJ installation by skilled installers, subsequent LIA connections need minimal training CLJ is supplied with SC adapters and pigtails preinstalled for single fibre applications CLJ can also be supplied with preinstalled connectorised passive splitters (1x4 or 1x8) Dedicated loose tube cable element storage area within the at the front of the closure Positive fibre management to 30mm bend radius Closure base contains one oval port, eight lead-in seal ports and two circular ports for spurs from the main cable loop Closure sealed to IP68 QUICKDR@W FTTH ACCESS SOLUTION JCS TECHNOLOGIES JCSTECH.COM.AU 5
QUICKDR@W CLJ SPECIFICATIONS Number of Cable Ports Maximum Cable Diameter (mm) 8 (Lead-in Seal), 1 (Oval), 2 (Circular) 7 (Lead-in Seal), 21 (Oval), 12 (Circular) Maximum Splice Tray Capacity 1 (16 Fibres), 1 upgrade (additional 24) General Material Maximum Capacity Maximum Loop Capacity Required Space Envelope (mm ) Operating Temperature Range Sealing Cap Base Splice Tray 8 customer connection cables 48 (4 x 12 fibre elements) L300 x W 231 x D 164 (L 410 with heat shrink) -20 to +70 C (5 to 95% RH) IP68 Glass Filled Polypropylene Glass Filled Polypropylene FR HIPS Closure Sealing IP68-AS60529-2004 IEC 60529 Ed 2.12001 Optical Dry Heat 1310, 1383, 1550 and 1625nm BS EN 60068-2-2 Test Bb Testing Damp Heat IEC 60068-2-3:1969 Change of Temperature IEC 60068-2-14: 1984 Vibration IEC 60068-2-6: 1995 Shock IEC 60068-2-27: 1987 QUICKDR@W CLJ LOGISTICS Packing dimensions Packed Weight (kg) Net Weight (kg) L 480 x W 250 x D 210 mm 2.4 1.9 KIT CONTENTS The QUICKDR@W Connectorised Lead-in Joint MK3 is supplied with a splice tray, connector patch panel, pigtails, oval port installation kit, splice protectors and a wall mounting bracket. Optional pre-installed 1x8 or 1x16 splitters are also available. QUICKDR@W CLJ ORDERING FCQ - CLJ-SCA-001-XXX CONNECTOR TYPE SCA SC/APC LCA LC/APC CONFIGURATION 008 8 Port 1x4 1x4 Splitter 1x8 1x8 Splitter 6 QUICKDR@W FTTH ACCESS SOLUTION JCS TECHNOLOGIES JCSTECH.COM.AU
QUICKDR@W ADDITIONAL ITEMS SUPPORT TOOL The Compact Joint Support Tool allows the user to support a Compact Joint or CLJ within a portable workbench. The bracket is designed to fit most commercially available workbenches. It is dimensioned to enable a splicing machine to be placed on the workbench for close access to the splicing trays. JCS PART NO. FCQ-CLJ-001-CST SECONDARY SPLICE TRAY The CLJ MK3 Secondary splice tray can be used to upgrade the splicing capacity of the CLJ MK3. The splice tray can accommodate 24 fibre splices and is used in applications where a spur cable is required to be dropped from the primary looped cable. JCS PART NO. FCQ-CLJ-001-SST CLJ CABLE ENTRY KIT The CLJ Cable Entry Kit is used to install an additional cable into one of the two circular ports. The kit comprises of a cable heat shrink, aluminium foil and a alcohol wipe. JCS PART NO. FCQ-CLJ-001-CEK QUICKDR@W FTTH ACCESS SOLUTION JCS TECHNOLOGIES JCSTECH.COM.AU 7
LOCAL MANUFACTURE, SERVICE AND SUPPORT JCS TECHNOLOGIES PTY LTD www.jcstech.com.au U1, 5-11 Mellor Street, West Ryde NSW 2114 T: +61 2 8878 6600 F: +61 2 9808 2622 E: sales@jcstech.com.au 0076-062016