MAKING MODERN LIVING POSSIBLE CO₂ A green Compressor clean thinking REFRIGERATION & AIR CONDITIONING DIVISION
CO₂ Compressor tailored for light commercial applications and heat pumps Our ultra-efficient new CO₂ reciprocating compressor was created in response to increasing customer interest in alternative refrigerants, especially for bottle coolers, vending machines and heat pumps. This was a special challenge, but one that our engineers responded to with imagination and energy. The unique thermodynamic properties of CO₂ mean that using it as a refrigerant at ambient temperatures above 30 C is tricky. The transcritical system operations required meant we had to create not only a capable compressor, but also a new system control strategy and heat exchanger concept. Product advantages Customer benefits Low noise level Environmentally friendly natural refrigerant Low energy consumption High cooling capacity High COP Low sound emission CO₂ is a natural gas and has no impact on the environment Low running cost Ensures the quality of your product Increases innovation in customer s own product High product quality Technology innovation
220-240V 50Hz 115V 60Hz 106B Barcode on white background Yellow background 0002 DANFOSS COMPRESSORS serial number 0004 Approvals DANFOSS COMPRESSORS Barcode on white background Green background 3.91"(99.3) 2.44"(62) C 40 4.19"(106.5) 2.91"(74) Approvals R744 White stripe serial number E G C G 8614 B A 0.98"(2.5) B1 Type labels & symbol drawings E ø0.75"(19) ø0.38"(9.7) 2.76"(70) 5.91"(150) 8.46"(215) 8.03"(204) 7.01"(178) 6.69"(170) 5"(127) 4"(101.6) 1.38"(35) ø0.63"(16) 5"(127) 6.50"(165) 7.32"(186) 8611-3 R744 8605-5 White stripe 106B 6.26"(159)
General Code number TN1406 R744, 220-240V 50Hz 106B0001 Approvals EN 60335-2-34 Compressors on pallet R744, 220-240V 50Hz 106B0002 EN 60335-2-34 TN1412 R744, 220-240V 50Hz 106B0012 EN 60335-2-34 R744, 220-240V 50Hz 106B0003 EN 60335-2-34 Frequency Hz Evaporating temperature C -15 to 7.2 Voltage range V 198-254 Max. discharge pressure bar 120 Max. winding temperature continuous (short) C 125 (135) -15 to 7.2 198-254 120 125 (135) -15 to 7.2 198-254 120 125 (135) -15 to 7.2 198-254 120 125 (135) Cooling requirements Frequency Hz 32 C F 2 38 C F 2 43 C F 2 LBP HBP LBP HBP LBP HBP LBP HBP LBP HBP LBP HBP LBP HBP LBP HBP F 2 F 2 F 2 S = Static cooling normally sufficient O = Oil cooling F 1 = Fan cooling 1.5 m/s (compressor compartment temperature equal to ambient temperature) F 2 F 2 F 2 F 2 F 2 F 2 F 2 = Fan cooling 3.0 m/s necessary SG = Suction gas cooling normally sufficient = not applicable in this area Motor Motor type LRA (rated after 4 sec. UL984), HST LST A 20.2 Cut in Current, HST LST A 20.2 Resistance, main start winding (25 C) Ω 3.8 13.7 20.2 20.2 3.8 13.7 20.2 20.2 3.8 13.7 20.2 20.2 3.8 13.7 Design Displacement cm 3 0.92 Oil quantity (type) cm 3 250 (polyolester) Maximum refrigerant charge Free gas volume in compressor cm 3 700 Weight without electrical equipment kg 15.5 g 1.54 250 (polyolester) 700 15.5 1.85 250 (polyolester) 700 15.5 2.46 250 (polyolester) 700 15.5 Dimensions Height mm A 190 B 185 B1 127 B2 Suction connector location/i.d. mm angle C 6.5 0 material comment Steel Al cap Process connector location/i.d. mm angle D material comment Discharge connector location/i.d. mm angle E 2.2 0 material comment Steel flexible Oil cooler connector location/i.d. mm angle F material comment Connector tolerance I.D. mm ±0.09 Remarks: - The discharge connector is a ø 3.2 mm flexible pipe. - Rated pressure burst disk G: 130 bar A 190 B 185 B1 127 B2 C 6.5 0 Steel Al cap D E 2.2 0 Steel flexible F ±0.09 A 190 B 185 B1 127 B2 C 6.5 0 Steel Al cap D E 2.2 0 Steel flexible F ±0.09 A 190 B 185 B1 127 B2 C 6.5 0 Steel Al cap D E 2.2 0 Steel flexible F ±0.09
TN1406,, R744, 220-240V 50Hz 35 C at gas cooler outlet, 220V, 50Hz, fan cooling F 2, preliminary data, LBP not approved Capacity in W 67 96 130 143 170 217 270 310 331 400 480 519 Power cons. in W 157 179 201 208 222 241 256 264 267 274 275 275 Current cons. in A 1.45 1.52 1.60 1.63 1.68 1.74 1.79 1.82 1.83 1.85 1.86 1.86 COP in W/W 0.43 0.54 0.65 0.69 0.77 0.90 1.05 1.17 1.24 1.46 1.75 1.89 20 C at gas cooler outlet, 220V, 50Hz, fan cooling F 2, preliminary data, LBP not approved Capacity in W 87 123 168 185 221 283 355 408 438 535 649 707 Power cons. in W 157 179 201 208 222 241 256 264 267 274 275 275 Current cons. in A 1.45 1.52 1.60 1.63 1.68 1.74 1.79 1.82 1.83 1.85 1.86 1.86 COP in W/W 0.55 0.69 0.84 0.89 1.00 1.17 1.39 1.55 1.64 1.95 2.36 2.57,, R744, 220-240V 50Hz 35 C at gas cooler outlet, 220V, 50Hz, fan cooling F 2, preliminary data, LBP not approved Capacity in W 164 219 282 306 355 438 531 599 637 756 892 959 Power cons. in W 241 276 312 324 346 373 395 404 408 413 410 407 Current cons. in A 1.95 2.07 2.20 2.24 2.31 2.41 2.48 2.52 2.53 2.55 2.54 2.53 COP in W/W 0.68 0.79 0.90 0.94 1.03 1.17 1.34 1.48 1.56 1.83 2.18 2.36 20 C at gas cooler outlet, 220V, 50Hz, fan cooling F 2, preliminary data, LBP not approved Capacity in W 211 282 365 396 461 571 697 791 842 1010 1207 1306 Power cons. in W 241 276 312 324 346 373 395 404 408 413 410 407 Current cons. in A 1.95 2.07 2.20 2.24 2.31 2.41 2.48 2.52 2.53 2.55 2.54 2.53 COP in W/W 0.88 1.02 1.17 1.22 1.33 1.53 1.76 1.96 2.06 2.45 2.94 3.21 TN1412,, R744, 220-240V 50Hz 35 C at gas cooler outlet, 220V, 50Hz, fan cooling F 2, preliminary data, LBP not approved Capacity in W 198 263 339 367 426 526 638 720 765 908 1072 1152 Power cons. in W 289 332 375 389 415 449 474 486 490 496 493 489 Current cons. in A 2.12 2.27 2.42 2.47 2.56 2.67 2.76 2.80 2.82 2.84 2.83 2.83 COP in W/W 0.69 0.79 0.90 0.94 1.03 1.17 1.35 1.48 1.56 1.83 2.17 2.36 20 C at gas cooler outlet, 220V, 50Hz, fan cooling F 2, preliminary data, LBP not approved Capacity in W 254 338 438 475 553 686 838 950 1012 1213 1450 1569 Power cons. in W 289 332 375 389 415 449 474 486 490 496 493 489 Current cons. in A 2.12 2.27 2.42 2.47 2.56 2.67 2.76 2.80 2.82 2.84 2.83 2.81 COP in W/W 0.88 1.02 1.17 1.22 1.33 1.53 1.77 1.95 2.07 2.45 2.94 3.21,, R744, 220-240V 50Hz 35 C at gas cooler outlet, 220V, 50Hz, fan cooling F 2, preliminary data, LBP not approved Capacity in W 281 370 473 512 592 726 877 986 1046 1238 1457 1564 Power cons. in W 399 454 508 526 558 599 629 643 647 653 646 640 Current cons. in A 2.50 2.69 2.88 2.94 3.05 3.20 3.30 3.35 3.37 3.38 3.36 3.34 COP in W/W 0.70 0.81 0.93 0.97 1.06 1.21 1.39 1.53 1.62 1.90 2.26 2.44 20 C at gas cooler outlet, 220V, 50Hz, fan cooling F 2, preliminary data, LBP not approved Capacity in W 361 477 612 663 768 947 1151 1301 1384 1653 1971 2131 Power cons. in W 399 454 508 526 558 599 629 643 647 653 646 640 Current cons. in A 2.50 2.69 2.88 2.94 3.05 3.20 3.30 3.35 3.37 3.38 3.36 3.34 COP in W/W 0.90 1.05 1.20 1.26 1.38 1.58 1.83 2.02 2.14 2.53 3.05 3.33
a3 TOP a2 e c b 8606 Start winding e Main winding 5 2 a2 Winding protector 1 1 2 2 N N L L 4 1 Bleeder resistance c a3 Thermostat M Fan Accessories for TN1406 TN1412 Figure Code number Starting device 470 mm cable length a3 117-7081 Cover b 103N2022 Starting relay a2 Components Start. capacitor 80 µf c of starting Run capacitor 10 µf e device Mounting accessories Code number Bolt joint for one compressor Ø: 16 mm 107B9150 Bolt joint in quantities Ø: 16 mm Snap-on in quantities Ø: 16 mm Test conditions TN1406 TN1412 Discharge pressure 90 bar Gas cooler outlet temperature 20 C / 35 C Suction gas temperature 20 C
General Code number 106B0004 Approvals Compressors on pallet R744, 115V 60Hz Frequency Hz Evaporating temperature F 5 to 45 Voltage range V 95-127 Max. discharge pressure bar 120 Max. winding temperature continuous (short) F 257 (275) R744, 115V 60Hz 106B0005 5 to 45 95-127 120 257 (275) Cooling requirements Frequency Hz LBP HBP LBP HBP 90 F F 2 100 F F 2 110 F F 2 S = Static cooling normally sufficient O = Oil cooling F 1 = Fan cooling 1.5 m/s (compressor compartment temperature equal to ambient temperature) LBP HBP LBP HBP F 2 F 2 F 2 F 2 = Fan cooling 3.0 m/s necessary SG = Suction gas cooling normally sufficient = not applicable in this area Motor Motor type CSIR/ LRA (rated after 4 sec. UL984), HST LST A 53.0 Cut in Current, HST LST A 53.0 Resistance, main start winding (77 F) Ω 0.9 2.9 Design Displacement cu.in 0.09 Oil quantity (type) fl.oz. 8.5 (polyolester) Maximum refrigerant charge Free gas volume in compressor fl.oz. 23.7 Weight without electrical equipment lbs. 30.9 Dimensions Height inch A 7.48 oz. B 7.28 B1 5.00 B2 Suction connector location, I.D. in. angle C 0.252-0.259 0 material comment Cu-plated steel Al cap Process connector location, I.D. in. angle D material comment Discharge connector location, I.D. in. angle E 0.09 0 material comment Steel flexible Oil cooler connector location, I.D. in. angle F material comment Remarks: - The discharge connector is a ø 0.13 inch flexible pipe. - Rated pressure burst disk G: 130 bar CSIR/ 53.0 53.0 0.9 2.9 0.15 8.5 (polyolester) 23.7 30.9 A 7.48 B 7.28 B1 5.00 B2 C 0.252-0.259 0 Cu-plated steel Al cap D E 0.09 0 Steel flexible F ø0 63"(16 8 03"(204 7 01"(178) 6 69"(170 ø0 75"(19) ø0 38"(9.7 86 4 G C 4 19"(106.5) 3 91"(99.3) 2 44"(62) C 5"(127) 4"(101.6) 1 38"(35) 5"(127 6 50"(165) 7 32"(186) 2.76"(70) 5.91"(150) 0.98"(2.5) 8 46"(215) B A B1 E 40 2.91"(74) 6.26"(159) E G
,, R744, 115V 60Hz 95 F (35 C) at gas cooler outlet, 115V, 60Hz, fan cooling F 2, preliminary data Evap. temp. in F -49-40 -31-22 -13-10 -4.0 5 14 20 23 32 41 45 50 59 68 Capacity in W 546 655 733 776 913 1068 1142 Power cons. in W 516 538 547 550 552 545 538 Current cons. in A 6.14 6.29 6.35 6.37 6.38 6.34 6.29 COP in W/W 1.06 1.22 1.34 1.41 1.65 1.96 2.12 68 F (20 C) at gas cooler outlet, 115V, 60Hz, fan cooling F 2, preliminary data Evap. temp. in F -49-40 -31-22 -13-10 -4.0 5 14 20 23 32 41 45 50 59 68 Capacity in W 712 860 967 1027 1219 1444 1556 Power cons. in W 516 538 547 550 552 545 538 Current cons. in A 6.14 6.29 6.35 6.37 6.38 6.34 6.29 COP in W/W 1.38 1.60 1.77 1.87 2.21 2.65 2.89,, R744, 115V 60Hz 95 F (35 C) at gas cooler outlet, 115V, 60Hz, fan cooling F 2, preliminary data Evap. temp. in F -49-40 -31-22 -13-10 -4.0 5 14 20 23 32 41 45 50 59 68 Capacity in W 910 1092 1222 1293 1521 1779 1904 Power cons. in W 812 851 866 872 876 863 851 Current cons. in A 8.30 8.60 8.72 8.76 8.79 8.69 8.60 COP in W/W 1.12 1.28 1.41 1.48 1.74 2.06 2.24 68 F (20 C) at gas cooler outlet, 115V, 60Hz, fan cooling F 2, preliminary data Evap. temp. in F -49-40 -31-22 -13-10 -4.0 5 14 20 23 32 41 45 50 59 68 Capacity in W 1187 1433 1612 1711 2031 2406 2594 Power cons. in W 812 851 866 872 876 863 851 Current cons. in A 8.30 8.60 8.72 8.76 8.79 8.69 8.60 COP in W/W 1.46 1.68 1.86 1.96 2.32 2.79 3.05 Test conditions Discharge pressure Gas cooler outlet temperture Suction gas temperature 90 bar 68 F / 95 F (20 C / 35 C) 68 F (20 C)
a3 a2 e c b f TOP 8610 Main winding R C S Start winding 5 2 e a2 1 Motor protector 1 1 2 2 N N L L 4 1 Bleeder resistance c a3 Thermostat M Fan Accessories for Figure Code number Starting device assembly 23.6 in. cable length 117-7082 a3 CSIR 23.6 in. cable length Cover b 103N2022 Starting relay a2 Components Start. capacitor 410 µf c of starting Run capacitor 23.5 µf e device Protector f 117U3212 Mounting accessories Code number Bolt joint for one compressor Ø: 5/8 in. 107B9150 Bolt joint in quantities Ø: 5/8 in. Snap-on in quantities Ø: 5/8 in.
Vending machines: as more and more major soft drinks manufacturers demand improved energy efficiency and environmental performance, they are increasingly looking for refrigerant alternatives to HFCs. CO₂ has proved itself a good alternative, creating an excellent, cost-effective solution to this challenge. Heat pumps: air or ground sourced heat pumps are highly responsive to energy savings. Compact, lightweight and high-performance designs can be made to deliver high thermal efficiency. By introducing CO₂ as a refrigerant, heat pumps achieve even better results, making CO₂ a good solution for this type of application. Filter drier for commercial applications CO₂ valve for light commercial applications DEHC.PB.550.A3.02/520N0640 compressors.danfoss.com Danfoss A/S G1 Advertising 08.08.UF.JN.paa