sales@jumo.co.uk info.us@jumo.net Page 1/10 JUMO dtrns p5 Pressure Sensor with IO-Link pplication Process automation Machines for the food and beverage industry General mechanical and apparatus engineering Brief description The pressure sensor serves to measure relative and absolute pressure and monitor it in liquids and gases. The effect of the pressure on the pressure sensor generates a signal, which is amplified, digitalized, and processed. The pressure sensor is equipped with an IO-Link interface according to specification 1.1. IO-Link supports bidirectional communication and is used to exchange process data, parameters, diagnostic information, and status messages. The two green LEDs are permanently lit as soon as voltage is supplied to the device. Once an IO-Link connection is established, the LEDs flash. The switching behavior and the switching thresholds of the switching outputs (max. pieces; p or n switching) can be individually configured - along with many other parameters. ny IO-Link master can be used for the configuration. The pressure sensor is therefore suitable for use in plant and mechanical engineering in connections to automation systems. variety of pressure connections and measuring ranges are available to the user. Type 0058 Customer benefits IO-Link Multi-vendor point-to-point connection Open standard with maximum transparency to the field level (IEC 6111-9) Inexpensive, pre-fabricated connecting cable (no wiring errors) Simple and uniform wiring and startup thanks to standardized interface Industry.0: pervasive communication from the control to the sensors Retrieval of process data and diagnostic information Dynamic parameter changes More safety during sensor replacement utomatic parameterization possible Replacement with sensors of same type, but with different properties, can be detected Optimization of the production process through communication down to the lowest field level Reduction of mounting and startup times Reduction of maintenance and service costs with simultaneous increase in plant availability Special features Small, compact, robust Stainless steel, fully welded Various process connections Hygienic connections (EHEDG) Simple startup Easy sensor replacement Proven accuracy Connection via IO-Link master LED status display lso available as a temperature sensor with IO-Link; see data sheet 90915 pprovals/approval marks (see "Technical data")
sales@jumo.co.uk info.us@jumo.net Page /10 Technical data Input Measuring range and accuracy Nominal measuring range Linearity a ccuracy at Long-term 0 C d -0to+80 C e stability b Signal processing Overload capacity c Burst pressure Bar % MSP f % MSP % MSP % MSP Bar Bar per year -00 to +00 mbar relative pressure 0. 0.7.0 0. 1 1.5-1 bar to +1 bar relative pressure 0. 0.6 1.8 0. 8-1 bar to +.5 bar relative pressure 0. 0.5 1. 16-1 bar to +5 bar relative pressure 0. 0.5 1. 0 60-1 bar to +1 bar relative pressure 0.5 0.5 1.0 100 150-1 bar to +0 bar relative pressure 0. 0.5 1.0 100 150-1 bar to +100 bar relative pressure 0. 0.5 1.0 00 00-1 bar to +50 bar relative pressure 0.5 0.7 1. 500 000-1 bar to +00 bar relative pressure 0.5 0.7 1. 800 000-1 bar to +600 bar relative pressure 0.5 0.7 1. 100 500 0 bar to +1 bar absolute pressure 0. 0.5 1. 0. 6 0 bar to.5 bar absolute pressure 0.5 0.5 1. 16 0 bar to +5 bar absolute pressure 0.5 0.5 1. 0 60 0 bar to +1 bar absolute pressure 0.5 0.5 1.0 100 150 0 bar to +0 bar absolute pressure 0. 0.5 1.0 100 150 0 bar to +100 bar absolute pressure 0. 0.5 1.0 00 00 a Linearity according to limit point setting. b Reference conditions EN 6198-1. c ll pressure sensors are vacuum proof. d Includes: linearity, hysteresis, repeatability, deviation of measuring range initial value, and measuring range end value. e Includes: linearity, hysteresis, repeatability, deviation of measuring range initial value, measuring range end value, thermal effect on measuring range start, and measuring span. f MSP = measuring span. Input filter Digital filter, nd order; filter time constant can be set Measuring circuit monitoring Process data invalid Measuring range overflow Measuring range underflow Device hardware fault IO-Link event configurable; appears in the process value as an error value
sales@jumo.co.uk info.us@jumo.net Page /10 Output Number Switching functions configurable Switching current Voltage drop at switching transistor Short-circuit proof Reverse polarity protected Current limiting Hysteresis For hysteresis function For window function Switch-on, switch-off delay Response time Switching output IO-Link 1 output in IO-Link operation (output signal according to IO-Link communication standard version 1.1; see section "Interface", page ) outputs for switch operation (SIO mode; SIO = standard IO) Hysteresis function or window function N/C or N/O contact Output p switching (PNP) or n switching (NPN) Switch-on/switch-off delay 100 m per output V Yes (clocked) Yes Yes Configurable Fixed setting (symmetrical; ±0.5 % of the measuring range) 0 to 100 s 7 ms 7 ms + IO-Link cycle time Interface Communication interface IO-Link device V 1.1, downward compatible to V 1.0 Data transfer rate (baud rate) COM (0. kbaud) Max. cable length 0 m, unshielded Min. cycle time ms IO Device Description (IODD) Depending on the ordered input range; available on the manufacturer's website www.jumo.de or at http://ioddfinder.io-link.com Electrical data Voltage supply In IO-Link operation DC 18 to V In switch operation DC 9.6 to V Nominal voltage DC V Current consumption In idle mode 10 m In IO-Link operation 1 m In switch operation 50 m (with switching outputs) Electrical safety Protection rating III according to DIN EN 6110 Intended use Pressure measurement in industrial plants The auxiliary energy of the pressure sensor must meet SELV requirements; optionally, an energy-limited current circuit according to section 9. of DIN EN 61010-1 and UL 61010-1 can be used.
sales@jumo.co.uk info.us@jumo.net Page /10 Mechanical features Materials Sensor Stainless steel (membrane: 1.5, welding ring: 1.0) High-pressure sensor Stainless steel 1.58 (for pressure ranges > 100 bar) Process connection Stainless steel 16L (1.0 or 1.571) Housing Stainless steel 0 (1.01) Installation position ny Calibration position Device upright, process connection at the bottom Weight pprox. 160 g Environmental influences dmissible temperatures Medium -0 C to +15 C mbient temperature -0 to +85 C (mbient temperature range of the head) Storage -0 to +85 C Resistance to climatic conditions During operation 100 % relative humidity without condensation on the outer skin of the device During storage 90 % relative humidity without condensation Climate class K7 according to DIN EN 6071-- dmissible mechanical load Vibration resistance 10 g, at 10 to 000 Hz according to DIN EN 60068--6 Shock resistance 0 g for 11 ms according to DIN EN 60068-- 50 g for 1 ms according to DIN EN 60068-- Process media Liquid and gaseous media Protection type ccording to DIN EN 6059 With absolute pressure version IP65/IP67 With relative pressure version IP65 Electromagnetic compatibility ccording to DIN EN 616-- Interference emission Class B - households and small businesses - Interference immunity Industrial requirement pprovals/approval marks pproval mark Test facility Certificate/certification Inspection basis Valid for number EHEDG TUM MK No. 0/006 Document no. 8 Process connection 997 JUMO PEK
sales@jumo.co.uk info.us@jumo.net Page 5/10 Dimensions Type 0058/000-XXX-58-5XX-0-6/000 Non-front-flush versions 50, 50, 511, 51 and 5; measuring range 100 bar Type 0058/000-XXX-58-5XX-0-6/000 Front-flush version 571, 57 and 575; measuring range 100 bar 10 M1 1 10 M1 1 66 66 Type 0058/000-XXX-58-997-0-6/000 JUMO PEK; measuring range 100 bar Type 0058/000-XXX-58-XXX-0-6/000 High-pressure version; measuring range > 100 bar 10 M1 1 10 M1 1 6 58
sales@jumo.co.uk info.us@jumo.net Page 6/10 Process connection 50 50 511 G 1/ DIN EN 87 G 1/ DIN EN 87 1/-18 NPT DIN EN 87 0 Nm 0 Nm 0 Nm 5.5 15.5 5.5 15 Ø 5 Ø 9.5 G 1/ 6 G 1/ Ø 6 Ø 17.5 1/-18 NPT 51 5 571 G 1/ DIN 85-11 G 1/ DIN 85-11 G / front-flush DIN 85-11 0 Nm 0 Nm 0 Nm.5 1 1 Ø 19 G 1/ 6.5 17 1 G 1/ 0 16 G / Profile seal G 1/ Profile seal G 1/ Profile seal G / 57 575 997 G 1/ front-flush with double seal G / front-flush with double seal JUMO PEK with EHEDG certification 0 Nm 0 Nm Ø 6 0 Nm.5.5 0.5 9 B.5 0.5 9 B.5 0.5 B Ø 18 G 1/ Ø.8 G / Ø Profile seal G 1/ Profile seal G / O-ring 6.5 W O-ring 15.1 1.6 W O-ring 0.5 1.78 W O-ring 1.5 Process connection for EHEDG-certified adapter system JUMO PEK (data sheet 09711)
sales@jumo.co.uk info.us@jumo.net Page 7/10 Connection diagram The connection diagram in the data sheet provides preliminary information about the connection options. For the electrical connection, only use the installation instructions or the operating manual. The knowledge and the correct technical compliance with the safety information and warnings contained in these documents are mandatory for mounting, electrical connection, and startup as well as for safety during operation. Connection Terminal assignment BN WH I/Q (OUT) 1 BK C/Q (IO-Link/OUT1) BU L Switch operation Voltage supply a DC 9.6 to V M1 x 1 round plug (-coded, non-rotating) 1 BN (brown) b BU (blue) Switching output 1 BK (black) C/Q = OUT1 Switching output WH (white) I/Q = OUT IO-Link operation Voltage supply a DC 18 to V 1 BN (brown) BU (blue) L- IO-Link BK (black) C/Q = IO-Link Switching output WH (white) I/Q = OUT Potential equalization Functional bonding conductor FB c L- a The auxiliary energy of the pressure sensor must meet SELV requirements; optionally, an energy-limited current circuit according to section 9. of DIN EN 61010-1 and UL 61010-1 can be used. b The colour coding is only valid for -coded standard cables! c The pressure sensor must be connected to the plant's potential equalization system via the process connection.
sales@jumo.co.uk info.us@jumo.net Page 8/10 Connection examples IO-Link operation with 1 switching output p switching (PNP) Switch operation with switching outputs p switching (PNP) BN BN WH I/Q (OUT) WH I/Q (OUT) 1 BK C/Q (IO-Link) 1 BK C/Q (OUT1) BU L BU L n switching (NPN) n switching (NPN) BN BN 1 WH BK I/Q (OUT) C/Q (IO-Link) 1 WH BK I/Q (OUT) C/Q (OUT1) BU L BU L
sales@jumo.co.uk info.us@jumo.net Page 9/10 Order details a b (1) Basic type 0058 JUMO dtrns p5 pressure sensor with IO-Link () Basic type extension 000 None 999 Special version () Input 7-00 to +00 mbar relative pressure 9-1 bar to +1 bar relative pressure 7-1 bar to +.5 bar relative pressure 8-1 bar to +5 bar relative pressure 56-1 bar to +1 bar relative pressure 5-1 bar to +0 bar relative pressure 515-1 bar to +100 bar relative pressure 508-1 bar to +50 bar relative pressure 509-1 bar to +00 bar relative pressure 516-1 bar to +600 bar relative pressure 88 0 bar to 1 bar absolute pressure 90 0 bar to.5 bar absolute pressure 500 0 bar to 5 bar absolute pressure 501 0 bar to 1 bar absolute pressure 50 0 bar to 0 bar absolute pressure 507 0 bar to 100 bar absolute pressure () Output 58 IO-Link measured value transmission, including digital output (5) Process connection 50 G 1/ DIN EN 87 50 G 1/ DIN EN 87 511 1/-18 NPT DIN EN 87 51 G 1/ DIN 85-11 5 G 1/ DIN 85-11 571 G / front-flush DIN EN ISO 8-1 a 57 G 1/ front-flush with double seal a 575 G / front-flush with double seal a 997 JUMO PEK with EHEDG certification a 999 Other process connections upon request (6) Process connection material 0 Stainless steel 16L (7) Electrical connection 6 Round plug M1 1 (8) Extra code 000 None 100 Customer-specific configuration (specifications in plain text) 591 Restrictor in the pressure channel b 61 Improved moisture and vibration protection The process connection can only be supplied for inputs (measuring range) up to 100 bar. Restrictor only for non-front-flush process connections. (1) () () () (5) (6) (7) (8) Order code / - - - - - / Order example 0058 / 000-56 - 58-50 - 0-6 / 000
sales@jumo.co.uk info.us@jumo.net Page 10/10 Scope of delivery Designation 1 pressure sensor in the ordered version 1 installation instructions ccessories Designation IO-Link master upon request Device data (IODD) on www.jumo.de or on http://ioddfinder.io-link.com