Jeep Wrangler Adjustable Rear Vision System for Factory Display Radios, 2007 Current (Kit # 9002-8847) Items Included in the Kit Camera Chassis Harness Power Harness 22--pin white connector w/ video RCA (for factory display radio) Program Module Zip lock bag with 15 Wire Ties & 3 Push Nuts Camera Extension Bracket These Instructions Required Tools & Supplies T15 & T20 Torx Bits 7mm & 10mm Sockets Phillips Screwdriver 3/8 Wrench or Socket Drive Plastic Trim Removal Tool Soldering Iron, Solder, & Heat Shrink Tubing (RECOMMENDED) or T-taps as an alternate splicing method Electrical Tape Please read so you do not VOID the warranty: If the camera harness is run through the center on the camera bracket, it will cut the camera harness. This will void the warranty on the camera. NOTE: We strive to provide accurate and up-to-date installation instructions.
Install Camera Step 1: Loosen lug nuts to remove spare tire. Adjustment Bracket for Camera Clearance using Phillips Screwdriver and 3/8 Wrench or Socket Drive Step 2: Slide Camera on studs placing harness end inside of tire carrier. Do not run harness through the camera bracket opening. Step 3: Adjust Camera head to fit your specific wheel. Bracket is shipped in factory wheel configuration. Note: Short Bracket has been designed for Factory offset wheels. Use the Long Bracket for wheels with larger offsets. Step 4: Remove spare tire and slide (3) supplied Push Nuts on the studs. Step 5: Reinstall spare tire.
Install Chassis Harness Step 6: Insert connector from Camera connector through the rear gate vent behind tire carrier. Step 9: Use supplied Wire Ties to secure Chassis Harness to existing harness. Step 10: Use supplied Wire Ties to secure Chassis Harness to existing harness. Step 7: Using a plastic trim removal tool, remove interior panels on inside of rear gate. Step 11: Use supplied Wire Ties to secure Chassis Harness to fabric factory wire cover. CAUTION: Leave enough slack to allow gate to open fully. Step 8: Pull harness through the rear gate openings.
Step 12: Use a T20 Torx bit to remove subwoofer box. Step 16: Pull back carpet and continue running Chassis Harness forward. Step 13: Using a plastic trim removal tool, pry off rear seat belt closeout. Step 17: Run Chassis Harness under B-pillar cover to passenger door sill. Use a plastic trim removal tool to remove the (2) plastic push pins and remove passenger sill plate/kick panel. Step 14: Using a plastic trim removal tool, remove rear access panel to expose 10mm bolt, and remove bolt. Step 18: Remove rubber bin insert from top of dash. Step 15: Pull out subwoofer box slightly to gain access to run Chassis Harness along existing harness
Step 19: Remove 7mm bolt. Step 22: Remove 7mm bolt. Step 20: Using a plastic trim removal tool, remove window switch panel. Step 23: Remove driver knee bolster cover. Step 21: Disconnect harness from window switches. Step 24: Remove (2) 7mm bolts on both sides of the steering column. Step 25: Remove center stack/cluster surround.
Step 26: Remove glove box for access and run Mirror Harness toward center of dash. Step 29: Connect Chassis Harness to Power Harness. Step 27: Using a plastic trim removal tool, remove HVAC panel. Step 30: Plug the Power Harness RCA connector into provided jumper harness. Step 28: Connecting Power harness. Splice Red power wire to Blue/Red wire on back of power point and Splice Black Ground to Black/White wire. RECOMMENDED: Use solder and cover with heat shrink tubing or use T-taps as an alternate connection method. Step 31: Insert the white 22-pin connector into the back of radio.
Programing Instructions PLEASE NOTE: These modules are VIN locked for single use. a) With the module not plugged in, key on the ignition and wait 10 seconds for the chimes and lights to stop flashing. b) Plug module into OBDII port, located under the dash on the driver s side, and wait to hear honk honk. Programming is completed. c) Unplug the module from the OBDII port. Green and white wires on the camera harness. Step 32: Test the system. Start vehicle and shift into Reverse in order to check that all connections were made properly. If all of the connections are correct you will see the camera image displayed on the factory display screen. To enable or disable the camera input, select from among rear vision options in radio settings. Step 33: Reassemble vehicle. Follow your disassembly steps in reverse order, taking care not to bind the harness wiring when reinstalling trim. NOTE: This camera has parklines or non parklines and mirror image or non mirror image options. Grid line options: Default setting is to display grid lines. To remove the grid line display, connect the two green wires near the end of the camera harness. Display options: (Not to be used in this application!) Default setting is mirror image display for rearward facing camera (rear view) installation. To change to non mirror image for forward facing camera (front view) connect the two white wires near the end of the camera harness.
Factory Display Camera Harness for Chrysler Town & Country, Dodge Durango, Grand Caravan, & Ram Tradesman, Jeep Commander, Grand Cherokee and Wrangler Factory Displays (Kit part number 9002-2632) NOTE: Requires Chrysler/Dodge dealer to activate; see below Applications: 2011 current Chrysler Town & Country (RBZ, RHB, RER, REZ, RBZ, REW radios) 2011 current Dodge Durango (RHR, RHB, RHZ, RHP radios) 2011 current Dodge Grand Caravan (RBZ, RHB, RER, REZ, RBZ, REW radios) 2011 current Dodge Ram Tradesman (RBZ, RHB, RER, REZ, RBZ, REW radios) 2008 2010 Jeep Commander (430, 730 radios) 2008 current Jeep Grand Cherokee (430, 730, RHR, RHB, RB2, RHP radios) 2007 current Jeep Wrangler (display radios) Please read thoroughly before starting installation and check that kit contents are complete. Items Included in the Kit: Factory Display RCA Jumper Harness Loose red and black wires (if needed) White 22-pin Connector These Instructions Tools & Supplies Needed: Delphi Terminal Removal Tool #12094429 or Small Flat Watch Repair Screwdriver 10mm Socket Plastic Trim Removal Tool Vehicle Service Manual (If needed) Safety Precautions: Work in well ventilated area that is clear of obstructions. Secure vehicle with tire chucks in both front and rear of tires. Turn vehicle accessories OFF and ensure ignition key is in OFF position. Wear safety goggles and snug fitting clothes. Use tools only for their intended purpose and which are in good repair. Only perform this task if confidence, skill, and physical ability permit. NOTE: We strive to provide accurate and up-to-date installation instructions. IMPORTANT: Use of this camera with the factory display requires activation by a Chrysler/Dodge dealer. See below for Dealer Programming Instructions. If possible, have the dealer enable the camera option prior to installation.
Step 1: Use a Plastic Trim Removal Tool to remove console and dash trim pieces to gain access to the radio bezel. Step 2: Use a Plastic Trim Removal Tool to remove radio bezel. Step 3: Unplug all radio connectors from the radio head unit and set radio aside. Only complete Step 4 and 5 for 2014+ Dodge Durango, Jeep Grand Cherokee, RAM Truck vehicles with 52-pin radio connectors. Step 4: Insert terminal from red wire on supplied jumper harness into position 31 of black 52-pin radio connector and insert terminal from black wire on supplied chassis harness into position 32 of black 52-pin radio connector. Continue with steps 6 through 9 for vehicles with 22-pin radio connector. IMPORTANT: If the White 22-pin connector is present in the vehicle and Pin 3 and/or Pin 4 are already populated, remove the terminal(s) using Delphi Terminal Removal Tool #12094429 or a Small Flat Watch Repair Screwdriver and isolate with Electrical Tape. Step 6: Remove both terminals from chassis harness. Splice provided loose red wire to chassis harness red wire and insert terminal into pin position 3 on the white 22-pin radio connector (Figure 1) until it clicks securely. Figure 1 Step 5: Connect male RCA of camera into female RCA of jumper harness and proceed to the Dealer Programming Instructions (Included). Step 7: Splice provided loose black wire to chassis harness black wire and insert terminal into pin position 4 on the white 22-pin radio connector (Figure 1) until it clicks securely. Step 8: Connect White 22-pin Connector to radio along with all remaining radio connectors before reinstalling radio head unit and all trim removed. Step 9: Connect male RCA of camera into female RCA of jumper harness and proceed to the Dealer Programming Instructions (Included).
Dealer Programming Instructions PARK VIEW REAR BACK-UP CAMERA VEHICLE CONFIGURATION Vehicle VIN must be updated with the sales code of the added accessory in order to enable system functionality. Using the DealerCONNECT website and the scan tool, complete the procedure below: A. In the Vehicle Option screen under Global Claims System category in the Service tab, enter the VIN and add the following sales code: XAC (PARK VIEW REAR BACK-UP CAMERA) as a Dealer Installed Option. B. Confirm that the new sales code has been successfully added to the VIN. With the scan tool connected to both the internet (via Ethernet port or wireless connection) and the vehicle, perform the following steps: C. Using the scan tool, select VEHICLE PREPARATION and then select RESTORE VEHICLE CONFIGURATION. D. Follow the step by step instructions on the scan tool to complete the Park View Rear Back-Up Camera vehicle configuration. Step 23: Start vehicle and shift into Reverse in order to check that all connections were made properly. If all of the connections are correct you will see the camera image displayed on your factory display. On our website you can discover more about cameras & driver safety.